The Antimatter Experiment: Gravity, Interferometry, Spectroscopy (AEGIS) at the European Organization for Nuclear Research (CERN) is an experiment investigating the influence of earth’s gravitational force upon antimatter. To perform precise measurements the antimatter needs to be cooled to a temperature of 100 mK. This will be done in a Penning trap, formed by several electrodes, which are charged with several kV and have to be individually electrically insulated. The trap is thermally linked to a mixing chamber of a 3He-4He dilution refrigerator. Two link designs are examined, the Rod design and the Sandwich design. The Rod design electrically connects a single electrode with a heat exchanger, immersed in the helium of the mixing chamber, by a copper pin. An alumina ring and the helium electrically insulate the Rod design. The Sandwich uses an electrically insulating sapphire plate sandwiched between the electrode and the mixing chamber. Indium layers on the sapphire plate are applied to improve the thermal contact. Four differently prepared test Sandwiches are investigated. They differ in the sapphire surface roughness and in the application method of the indium layers. Measurements with static and sinusoidal heat loads are performed to uncover the behavior of the thermal boundary resistances. The thermal total resistance of the best Sandwich shows a temperature dependency of T-2,64 and is significantly lower, with roughly 30 cm2K4/W at 50 mK, than experimental data found in the literature. The estimated thermal boundary resistance between indium and sapphire agrees very well with the value of the acoustic mismatch theory at low temperatures. In both designs, homemade heat exchangers are integrated to transfer the heat to the cold helium. These heat exchangers are based on sintered structures to increase the heat transferring surface and to overcome the significant influence of the thermal resistance (Kapitza resistance). The heat exchangers are optimized concerning the adherence of the sinter to the substrate and its sinter height, e.g. its thermal penetration length. Ruthenium oxide metallic resistors (RuO2) are used as temperature sensors for the investigations. They consist of various materials, which affect the reproducibility. The sensor conditioning and the resulting good reproducibility is discussed as well.

Master’s thesis contains description parameters of microcontroller ATMEGA644P, also contains differences between older and newer version of microcontrollers ATMEGA644 and ATMEGA644PA. Inside structure of microcontroller, memories and peripherals are described here. The construction of the universal microcontroller unit is main target of this thesis. The unit contains supply, A/D converter, current loop, communication interfaces, temperature sensor, accelerometer and other. The unit collects and saves data, communicates by interfaces and manages other functions. Using devices and circuits are described in this thesis. Development of software for microcontroller(firmware) are positioned to last part of this thesis. This software control functions of all parts positioned on the unit.

The Antimatter Experiment: Gravity, Interferometry, Spectroscopy (AEGIS) at the European Organization for Nuclear Research (CERN) is an experiment investigating the influence of earth’s gravitational force upon antimatter. To perform precise measurements the antimatter needs to be cooled to a temperature of 100 mK. This will be done in a Penning trap, formed by several electrodes, which are charged with several kV and have to be individually electrically insulated. The trap is thermally linked to a mixing chamber of a 3He-4He dilution refrigerator. Two link designs are examined, the Rod design and the Sandwich design. The Rod design electrically connects a single electrode with a heat exchanger, immersed in the helium of the mixing chamber, by a copper pin. An alumina ring and the helium electrically insulate the Rod design. The Sandwich uses an electrically insulating sapphire plate sandwiched between the electrode and the mixing chamber. Indium layers on the sapphire plate are applied to improve the thermal contact. Four differently prepared test Sandwiches are investigated. They differ in the sapphire surface roughness and in the application method of the indium layers. Measurements with static and sinusoidal heat loads are performed to uncover the behavior of the thermal boundary resistances. The thermal total resistance of the best Sandwich shows a temperature dependency of T-2,64 and is significantly lower, with roughly 30 cm2K4/W at 50 mK, than experimental data found in the literature. The estimated thermal boundary resistance between indium and sapphire agrees very well with the value of the acoustic mismatch theory at low temperatures. In both designs, homemade heat exchangers are integrated to transfer the heat to the cold helium. These heat exchangers are based on sintered structures to increase the heat transferring surface and to overcome the significant influence of the thermal resistance (Kapitza resistance). The heat exchangers are optimized concerning the adherence of the sinter to the substrate and its sinter height, e.g. its thermal penetration length. Ruthenium oxide metallic resistors (RuO2) are used as temperature sensors for the investigations. They consist of various materials, which affect the reproducibility. The sensor conditioning and the resulting good reproducibility is discussed as well.

[pt] Diferentes tipos de lasers podem ser usados para gerar pulsos de luz com uma ampla faixa de durações de pulso, energias e potências de pico. As técnicas de Q-switching e mode-locked são relatadas há anos por vários autores e pesquisadores e são frequentemente utilizadas na geração de lasers de pulso ultracurto com duração de pulso no domínio do tempo na faixa de nanossegundos até femtossegundos. Uma configuração, com ganho fornecido por um amplificador óptico semicondutor (SOA) e amplificador de fibra dopada com érbio (EDFA) é proposta e emprega a técnica de gerenciamento de dispersão para gerar um trem de pulsos ópticos exibindo alta potência de pico, taxa de repetição ultra-baixa e largura temporal curta, habilitando que este laser seja usado como uma fonte para aplicações de alta resolução em reflectometria óptica no domínio do tempo (OTDR). A operação mode-locked é conhecida por ocorrer apenas em lasers ordenados padrão por um longo tempo e até recentemente foi encontrado também em lasers de fibra aleatórios desordenados (RFL). Embora tenha havido progresso no sentido de travar modos espaciais e longitudinais em lasers aleatórios, a literatura carece de relatos sobre geração de pulsos limitada por transformada de Fourier, apesar das muitas décadas de campo. O autor demonstra experimentalmente um mode-locked random fiber laser (MLRFL) operando como um refletômetro óptico de domínio do tempo sensível à fase. Aqui, a saída total do laser fornece o sinal de detecção, em contraste com o pequeno sinal retroespalhado medido em um OTDR convencional. O laser opera como um sensor acústico distribuído (DAS) e sensor de temperatura distribuído (DTS). / [en] Different types of lasers can be used to generate light pulses with a wide range of pulse durations, energies and peak powers. Q-switching and mode-locked techniques have been reported for years by several authors and researchers and are frequently used in the generation of ultra-short-pulse lasers with time-domain pulse durations from the nanosecond to femtosecond range. A configuration, with gain provided by a semiconductor optical amplifier (SOA) and erbium-doped fiber amplifier (EDFA) is proposed and employ the dispersion management technique to generate a train of optical pulses exhibiting high-peak-power, ultralow repetition rate, and fast temporal width, enabling this laser to be used as a source for high-resolution optical time domain reflectometer (OTDR) applications. The mode-locking operation has been known to occur only in standard ordered lasers for a long time and until recently it was found to also occur in disordered random fiber lasers (RFL). Although progress has been made towards locking spatial and longitudinal modes in random lasers, the literature lacks reports on Fourier transform-limited pulse generation despite the many decades of the field. The author experimentally demonstrates a mode-locked random fiber laser (MLRFL) operating as a lasing phase-sensitive optical time domain reflectometer based on random feedback from a sensing fiber. Here, the full output of the laser provides the sensing signal, in contrast to the small backscattered signal measured in a conventional OTDR. The laser operates as a distributed acoustic sensor (DAS) and distributed temperature sensor (DTS).

This thesis is developed as a proposal for heating for a primary school and kindergarten in the region of Brno-countryside. For the insulated building, a combination of heating and air-conditioning is proposed. The concept is designed so that the air-conditioning preheats the exterior air and the heating system warms the incoming air to a comfortable temperature. For the required thermal performance, sources of heat (for gas and pellets) and a layout solution for the boiler room is designed. Drainage of combustion products is proposed for both solutions. The project solution is per the extent of the construction permit. The theoretical part is linked with the practical part through the condensation boilers, their function and division, and drainage of combustion products. The experiment for the given topic was conducted on the drainage of combustion products. The pressure loss of the reverse knob was determined in relation to the flow rate of air in the condensation boilers as this loss is essential in assessing the drainage of combustion products.