Disertační práce je zaměřena na kovové a polymerní výměníky tepla. Hlavním předmětem zkoumání je optimalizace teplosměnných ploch za účelem zvýšení účinnosti výměníku tepla. Tyto cíle byly dosaženy experimentálně a numericky pomocí modelování v ANSYS. Na základě dosažených výsledků byla rozpracována technologie křížového navíjení polymerních výměníků z dutých vláken. Experimentální zařízení původně určené pro navíjení tlakových nádrží bylo modifikované pro automatizovanou výrobu polymerních výměníků z dutých vláken, ježto může být použita při jejich masové výrobě. Tato práce se také zabývala výměníky tepla pro klimatizační systémy. Byly zkoumány možnosti využití polymerních výměníků z dutých vláken v těchto systémech. Mimo jiné byla provedena studie vlivu cyklického tepelného zatížení standardního kovového žebrovaného tepelného výměníku.

In this paper is carried out basic design and calculation of tube heat exchanger with a straight tube bundle with installed systém of disk and doughnut baffles. The calculation included pressure losses and heat transfer coefficient of tubular space and shell side. Then CFD model was made for parametric study, which was focused on influence of change of the baffles geometry on the heat output of the exchanger and the pressure loses on the shell side.

The diploma thesis contains calculations of gasification of coal boiler. The first part of thesis contains stochiometric calculations, heat balance and calculations of combustion chamber. In the next part are calculations of heat exchange surfaces and at the end of this part are calculations of regenerative air heater and total boiler balance. Calculations are made by regard to investments costs, preservation of the steam parameters and keeps emissons limits.

The following master’s thesis examines the use of biothermal energy released during the decomposition process of composting. The aim of this thesis is to explain the heat generation principles of composting, to summarize its consumption possibilities, and to design a suitable use of the source for the demands of a real building. First, the theoretical framework compares various options of the biomass utilization. It then describes the biochemical course of organic matter decomposition, and conceptualizes the term thermocompost as well as different methods of heat extraction. Subsequently, it lists ways of applying this technology in practice. Second, the empirical part uses the findings to propose a compost pile installation, and its connection to the current heating and hot water system in Ecocentre Karpaty in Nová Lhota, Hodonín. Due to the low-temperature nature of the source and the mode of usage of the building, it is recommended to accumulate the heat generated in the hot water storage tank. The preheating of potable water is considered as its primary benefit. In case of sufficiently high temperature of the thermocompost, the design also includes the possibility of preheating of heating water. In conclusion, the thesis evaluates the financial costs of the project and determines the financial savings. These have – due to the low frequency of the building usage and the consumption of hot water reach – relatively low values.

The aim of this thesis is a draft of a gas steam boiler with steam output of 200 t/h. The first part of the paper provides stoichiometric calculations, then there are calculations of the dew point, boiler efficiency and the amount of gas. After that, calculations and a draft of the combustion chamber are carried out and then heat balances are drafted. In the following text, geometric properties of individual heat exchanging surfaces are drafted. At the end, there are control calculations. This thesis contains a blueprint of the gas steam boiler.

The diploma thesis deals with comparison of heat loss calculation by CSN 06 0210 and CSN EN 12831. This work contains short introduction to the heat loss calculation, definition of basic terms, detailed analysis of heat loss calculation by both standards, description of exemplar buildings, heat loss calculation and heat requirement for heating of buildings according to particular standards. At the end of the work the comparison and discussion of calculation results is presented.

Viktor Lípa Stillage boiler Graduation theses, power department, 2008 This graduation theses deals with designer solution of the boiler, include the dimensioning heat exchangers and engineering designer of the economizer chamber. Boiler is used for stillage combustion and fitted by natural circulation in vaporizer and stoker fired furnace.

The main subjekt of that diploma thesis is an optimalization energetic ekonomy of a bathroom. The ojective is propose suitable resolution for decrease decrement heating and employ outlet heat of burnt gas which are going from steam generator. In the first part of thesis is evaluation inceptive state, inlet and outlet flows of energies. In the next part, there are confront indivudual resolving from technically angle and economically angle.

The main subjekt of this master’s thesis is the description of the processes of production of beer in a cold block, describing the theory of sanitation and theory of CIP cleaning station. The second part of this work is practical proposal of CIP cleaning station, selecting anappropriate heat exchanger, its design and economic evaluation of the proposed CIP station.

The thesis is focused on the cooling cycles, namely cycles of absorption. The work is divided into several parts, as problems to be solved. The first part deals with the principles and using refrigeration cycles in practice, their involvement and by comparing the working pairs of substances circulating in the absorption unit. The practical part deals with making a proposal for one-and two-level modular absorption cycle of 6 kW, and the subsequent techno-economic comparison with commonly supplied absorption unit