This thesis deals with the change of the fuel base of a coal boiler due to the reduction of CO2 emissions and its thermal recalculation. In the first part, there is implemented calculation of the combusting chamber. This is followed by the recalculation of the heat transfer surfaces. The emphasis is placed on the preservation of the exsiting steam parametrs.

This diploma thesis deals with the design of a structure for heat transfer path of miniaturized heat switch. The focus is on production using SLM additive technology. The aim is to assess the possibilities of using metal 3D printing on a part intended primarily for heat transfer. This work presents several concepts of structure arrangement, which are further analysed and evaluated. The results show the potential of additive technologies in this area and the proposed structures meet the heat transfer requirement according to the calculations used.

This diploma thesis is dedicated to the design of a combustion air heater for a biomass boiler with a water content of over 60%. The first part of the thesis describes biomass and its use in energetics. Furthermore, the stoichiometry of combustion, heat transfer in the exchanger, design of dimensions and air pressure losses are calculated. The last chapter describes the method of air heating regulation.

This thesis project solve problematic of thermal proces in lead-acid batteries. There are decribed history of lead – acid batteries, distributions of batteries, overview of construction lead – acid batteries and VRLA batteries and is decribed thermal runaway proces and basic termal process. They are listed here practical results and the measurements is concluded.

This thesis describes the design of a new circuit for the production of superheated steam instead of the original heat exchanger, which showed frequent failure. In the introduction is disassambling the problems of the existing heat exchanger and the proposed method of solving the problem. Proposed is a new process circuit consisting of a heat exchanger to heat the steam, separator and heat exchanger for superheated stream. Gradually, the work both heat exchangers are designed thermal and strenght. In the thermal part is modeled all process circuit and calculated in the program ChemCad. The strength calculation is solved analytically according to EN 13 445, then all dimensions of heat exchangers are optimized. In the conclusion is verified by metod of finite element critical part of the exchanger. After successful completion of the design thermal and strength calculation was made relevant drawing documentation.

This master thesis follows the bachelor thesis with the same name. It is looks into the analyses of the combi-cycle, the advantage of which is high efficiency and easy separation of CO2 for its storage and further usage. It introduces the Graz cycle, its thermal balance a basic arrangement. The calculation is attached in a separate .XLS file. At the end of the thesis, the result of the calculation is interpreted and the conditions under which the project would be realized are outlined.

This master’s thesis deals with a design of Na-CO2 heat exchanger. There is a comparison of shell and tube heat exchanger with PCHE in the first part. Further the shell and tube heat exchanger with internally finned tubes was chosen as the basic conception. There was performed an optimization of construct and operations parameters for this concept. The optimization was performed on the basis of thermal and hydraulic calculations. Further there were performed calculations for ensuring of safe operation of the heat exchanger. The conclusion of the diploma thesis deals with comparison of the designed heat exchanger with similar projects.

Graduation these deals with investigation of critical heat flux in pressurized water nuclear reactors. Theoretical part covers fundamental terms from area hydrodynamics of two-phase flow and critical heat flux. Here are also mentioned the individual approaches to description of physical process of heat transfer crisis. Practical part is devoted to systems design of measuring stand for critical heat flux in vertical canal allowing visualization of two-phase flow.

The topic of this thesis is the thermal calculation of steam boiler with natural gas fuel. The first part is describing technical characteristic and parametres of the boiler. The main part of this thesis is the thermal calculation of the boiler. The following part deals with determination of steam amount and steam parametres for blowing through pipes of the boiler.

Diplomová práce se zabývá spalováním zemního plynu při využití vzduchu s vyšším obsahem kyslíku (21–46 % kyslíku ve spalovacím vzduchu), tzv. kyslíkem obohaceným spalováním (OEC). Technologie OEC nalezla uplatnění v průmyslu, kde se jsou nároky na zvýšenou produktivitu, dosažení vyšší tepelné účinnosti, zlepšení vlastností plamene, snížení náklady, či zlepšení kvality výsledného produktu. Ačkoliv OEC přináší řadu výhod, je nutné zmínit i nevýhody jako: poškození zařízení, nestejnoměrné zahřívání, narušení plamene, zvýšené emise anebo zpětný zášleh plamene. Zkoušky proběhly na zkušebně hořáků, která umožňuje testovat hořáky nejen na plynná a kapalná paliva, ale i hořáky navržené pro kombinované spalování při maximálním výkonu hořáku 1 800 kW. Při zkouškách byl použit plynový „low-NOx“ hořák se stupňovitým přívodem paliva. V diplomové práci je popsán vliv obsahu kyslíku ve spalovacím vzduchu na emise oxidů dusíku (NOx), teplotu plamene, přenos tepla ze spalin do stěn spalovací komory, a také vlastnosti plamene, zvláště pak jeho stabilitu, tvar a rozměry. Zkoušky proběhly při výkonech 300 kW, 500 kW a 750 kW, přičemž pro výkon 750 kW proběhly testy jak při jednostupňové, tak dvoustupňové konfiguraci.