The subject of this diploma thesis is optimalization of exhaust manifold of ŠKODA 1,2 MPI engine with respect for the plastic deformation at heat stress. The first part is focused on general description of converter module, whose component the exhaust manifold is. In the next part of the thesis is computation of a heat load of the exhaust manifold. The last part is devoted to the seal analysis of the whole converter module of a ŠKODA three-cylinder engine.

Práce se zabývá studiem procesů probíhajících při zhášení silnoproudého oblouku ve zhášecí komoře jističe. Je zaměřena na výpočet dynamiky tekutin a teplotního pole v okolí elektrického oblouku. V práci je dále popsán vliv vzdálenosti plechů v komoře a vliv tvarů plechů z hlediska aerodynamických podmínek uvnitř komory. Dalším cílem dosaženým touto prací je poskytnutí informací o vlivu polohy elektrického oblouku na termodynamické vlastnosti uvnitř komory. Toto je důležité, zejména pokud je oblouk do komory vtahován jinými silami, např. elektromagnetickými a během tohoto vtahovacího procesu mění svůj tvar i polohu. Za účelem co nejjednoduššího, ale zároveň co nejefektivnějšího řešení úkolu, byl vyvinut software určen speciálně pro výpočet dynamiky tekutin numerickou metodou konečných objemů (FVM). Tato metoda je, v porovnání s rozšířenější metodou konečných prvků (FEM), vhodnější pro výpočet dynamiky tekutin (CFD) zejména proto, že režie na výpočet jedné iterace jsou menší v porovnání s ostatními numerickými metodami. Další výhodou tohoto softwarového řešení je jeho modularita a rozšiřitelnost. Cely koncept softwaru je postaven na tzv. zásuvných modulech. Díky tomuto řešení můžeme využít výpočtové jádro pro další numerické analýzy, např. strukturální, elektromagnetickou apod. Jediná potřeba pro úspěšné používání těchto analýz je napsáni solveru pro konečné prvky (FEM). Jelikož je software koncipován jako multi–thread aplikace, využívá výkon současných vícejádrových procesorů naplno. Tato vlastnost se ještě více projeví, pokud se výpočet přesune z CPU na GPU. Jelikož současné grafické karty vyšších tříd mají několik desítek až stovek výpočetních jader a pracují s mnohem rychlejšími pamětmi, než CPU, je výpočetní výkon několikanásobně vyšší.

The aim of the Master thesis is to design and verify the function of the system for the ventilation of parked car in the summer season with the intention to cut down the temperature peak in the cabin of the vehicle. The design of the system consists of the suitable placement of the fans and corresponding inlets and outlets for the flowing of the ventilating air. The fans are powered by a photovoltaic panel. The functionality of the system is verified by the measuring of the temperature drop in the cabin of the car. The ambient conditions for the setting of the intensity of solar radiation and of the ambient temperature have been chosen from the real measurements from TUBO station which is meteorological station of the Faculty of Civil Engineering of BUT Brno.

This master thesis deals with the possibilities of traffic of nuclear power unit at thermal and power effect at the end of the campaign, focusing on VVER reactors. For a better idea of the reader the design of key components of the unit in terms of performance is analysed. Parameters of relevant components for Dukovany NPP are presented briefly. The possibilities of traffic of nuclear power unit on thermal and power effect at the end of the campaign are particularly demonstrated on the example of the Dukovany NPP. Furthermore the program Moby-Dick is introduced and the basic possibilities for its use to calculate the course of the campaign are described. At the end of the thesis, we conducted sample calculations for the duration of the campaign on the fourth block of the nuclear power plant.

The master´s thesis contained basic information about the method of thermodynamic efficiency of hydraulic machines. The first part briefly mentioned our opinion on the most widely used method for determining the efficiency of hydraulic machines. Another section of thesis is characterization and measurement procedure using the thermodynamic method. Another section describes measurements of water plants and laboratory measurements, which took place in the past. The final part describes the results of laboratory measurements, which took place in the lab of VUT FSI Brno, and evaluating and comparing the results.

This work deals with the measurement of temperature fields in the air using an infrared camera. The dissertation describes the opportunity of measuring the temperature field in the air and the characterization of the developed measuring method. In the next part there are introduced the beginning of thermography imaging and the field of usability of the new infrared measuring method. Further, the theoretical foundations of the thermography measuring method in the temperature fields in the air are described. In the theoretic background there are described the analysis of heat conduction in an auxiliary material, the determination of dynamic properties of the method and the analysis of radiation, which has an influence on infrared imagining. This method requires an insertion of the auxiliary material into the non-isothermal air flow, which can allow for the study of the temperature distribution in air. For effective visualization of temperature fields in the air using an infrared camera, the selection of the appropriate auxiliary material, on which the air temperature displays, is crucial. In the next part of the doctoral thesis, there is a description of static measuring properties of auxiliary materials. The usability range of the measuring method is determined from these properties. In the thesis there are presented the description of the device for the measurement of 2D temperature fields in the air and the description of the measuring device for 3D measurements of temperature fields in the air using an infrared camera, which can also be used for measurements of temperature fields in small enclosed spaces through a viewing window. For the practical use of the method, the detailed methodology of measuring temperature fields in the air by an infrared camera was developed and its applicability was demonstrated on practice examples. The developed measuring method can be used in many areas of research and in practice.

The aim of this diploma thesis is to focus on the resistance of concrete exposed to high temperatures especially with focus of resistance against explosive spalling as well as clarifying the mode of action of various types of polypropylene fibres. The theoretical part is an introduction to the issues of explosive spalling, its mechanisms and majority influencing factors. Further description of the processes taking place in the structure of concrete under extreme thermal load, distribution and size of pores in concrete, thermal load, temperature-time curves and their applications, methods of elimination of negative behaviour of concrete exposed to thermal loading (passive and active methods), mode of action of polypropylene fibres and more is also included in the theoretical part. The main aim of experimental part is to verify the function of polypropylene fibers of various Melt Flow Indexes (MFI) and dosage. Primarily, the test samples with content of the PP-fibers are compared to the reference sample without fibers. Secondarily, the samples with standard PP-fibers (with MFI 25) with dosage 2.0 kg/m3 are compared to samples with modified PP-fiber (with MFI 2500) of dosage 0.9 kg/m3. Photogrammetric images were used for evaluation and comparison of spalled surfaces and its depth. Determination of the softening temperature and melting point of the modified and standard PP-fibers was made by using a high temperature microscope video. The second part of the experimental work was to define concrete permeability at different temperatures and pressures. Permeability was measured at temperatures of 20°C, 90°C, 150°C, 175°C, 200°C, 225°C and 250°C and at pressure of 0.2, 0.4 and 0.6 MPa.

This thesis deals with the behavior of cement concrete at high temperature with a focus on the impact behavior of aggregate, cement type and polypropylene fiber reinforcement. The theoretical part describes the issue of cement concrete at high temperatures, especially processes in the cement matrix, aggregates and polypropylene fibers. Furthermore, theoretical part describes the selection of a suitable type of cement and aggregates in concrete exposed to high temperatures. In the experimental part was designed the concrete composition with various kinds different types of aggregates and two types of cements. The temperature stress of test samples was performed according to ISO standard temperature curve 834. Subsequently, was made the verification of the physic-mechanical properties such as changes in bulk density and compressive strength after heat load. Moreover, the surface appearance of samples after heat load was evaluated, especially the occurrence of samples, the crack width and explosive spalling. Mineralogical composition changes of prepared samples before and after heat load were observed via X-ray diffraction analysis. Finally, we made a photogrammetry on a test plates after heat load which defined the size of the area and depth of spalling concrete surface.

This diploma thesis focuses on strength design of steam condenser. The goal of the thesis is to make strength calculations for the specific operation conditions, introduce possible solutions, provide recommendations and refer to weak points of such calculation procedures. First, thermal-hydraulic design in HTRI software is performed. Strength calculations respect ČSN EN 13445 standard. Strength calculation with imported temperature field is performed in ANSYS Workbench software. In the next step, another strength calculation is realized in Sant´ Ambrogio software. Results are evaluated in conclusion chapter, including recommendations for the possible following work.

This master‘s thesis is focused on the study of the behavior of cement concrete at high temperatures with a focus on monitoring the impact of aggregate and cement type. This work describes the processes in aggregates and cement matrix at high temperatures. The theoretical part describes the selestion of a suitable aggregate and cement for the surroundings with potential exposure to high temperatures. In the experimental part is given design of composition of a concrete with two types of aggregates and four cements. It has been suggested 8 recipes. Changes were observed densities, compressive strength and tensile strength in bending, calculate the velocity of propagation of waves with ultrasonic pulsed method. Also evaluated the appearance of the surface samples after thermal load – cracks on the surface and measure the maximum crack width.