In the production of cement, to increase the cement/clinker ratio and decrease CO2 emission, the most important alternative is to produce mineral admixture incorporated cements (CEM II-III-IV-V) instead of portland cement (CEM I). These cements are usually produced by intergrinding the portland cement clinker and the mineral admixtures. However, the difference between grindabilities of the different components of such cements may cause significant effects on the particle size distribution and many other properties. For this reason, separate grinding of additives and clinker may be thought as an alternative. In this study, the effects of intergrinding and separate grinding on the particle size distribution and consequently on the strength of portland composite cements which contained natural pozzolan (trass), granulated blast furnace slag (GBFS) and limestone besides portland cement clinker were studied.

Properly proportioned, placed and cured concrete can be durable under most conditions. However, deterioration of concrete does occur under certain environments. One of the problems that affect the durability of hardened concrete is delayed ettringite formation (DEF) which is an important problem encountered in precast concrete industry where high temperature curing is applied. Although there had been many researches on DEF, there are still many uncertainties about its chemistry and mechanism. In this study, the effects of partial cement replacement by different mineral admixtures (trass, blast furnace slag and fly ash), SO3/Al2O3 molar ratio and specific surface area of cement on DEF were investigated. For this purpose, 9 groups of control cements were prepared with 3 different specific surface areas and 3 different SO3/Al2O3 molar ratios. Different amounts of mineral admixtures were blended with the control cements. High temperature curing was applied to the cement pastes and the expansions of these pastes were measured periodically for 240 days. v The experimental results obtained were interpreted for a comparative analysis of the effects of the afore-mentioned parameters.

In 2017, the Swedish Parliament stated a new climate law with the goal that Sweden should be climate neutral by 2045. The concrete industry has developed a roadmap on how the goal for 2045 can be achieved, where one way to reduce the carbon emissions from concrete is by replacing a part of the cement clinker with alternative binders in the concrete mix. Ground granulated blast furnace slag (GGBS), fly ash, silica fume and trass are alternative binders that are possible to use in concrete mixes to reduce the amount of ordinary Portland cement (OPC). GGBS, fly ash and silica fume are by-products from other industries, while trass is volcanic ash that can be extracted. Besides the positive environmental impact that comes from using alternative binders and reducing the amount of cement clinker, the alternative binders have other properties, both positive and negative, that affect the concrete. The aim of this thesis was to investigate whether concrete with alternative binders does fulfill the regulations set by Swedish standards and how concrete with alternative binders does affect the material parameters. The concrete mixes were divided into three different types of concrete: concrete for bridges (w/c ratio 0.4), hydropower structures (w/c ratio 0.45) and wind powerplant foundations (w/c ratio 0.55). A total of seven concrete mixes were cast in a laboratory and the concrete mixes were investigated in the three hardening stages of concrete: fresh, young and hardened. The analyzed material parameters were compressive strength, shrinkage, frost resistance, workability, air voids and temperature development. Beyond the experimental testing, a global warming potential (GWP) comparison was made to compare the reduction of GWP for each concrete mix compared to a reference concrete for each usage area. The mix containing a CEM II/A-V fly ash cement and 15% GGBS showed great potential regarding the different material parameters. This mix, however, is according to Swedish standards not possible to certify for structures in exposure class XF4, such as bridges, but is possible to certify for structures in exposure class XF3, such as wind powerplant foundations. The mix containing 30% GGBS and 5% silica fume also showed beneficiary properties, but superplasticizers are required in this mix to ensure good workability. For hydropower structures, the mix containing 35% GGBS showed a great compressive strength but a high temperature development and low workability. The mix containing trass had a notably low temperature development, but with an increase in shrinkage and low workability. Moreover, all concrete mixes showed a frost resistance which, according to standard, is classified as “Very Good”. / Sveriges regering antog 2017 ett nytt klimatpolitiskt ramverk med målet att Sverige ska ha noll nettoutsläpp av växthusgaser år 2045. Betongindustrin har tagit fram en färdplan för hur betong kan bli klimatneutralt, där ett sätt att reducera klimatpåverkan från betong är att byta ut en del av cementklinkern mot alternativa bindemedel. Mald granulerad masugnsslagg (GGBS), flygaska, silikastoft och trass är alternativa bindemedel som är möjliga att använda i betongblandningar för att reducera mängden Portlandcement. GGBS, flygaska och silikastoft är restprodukter från andra industrier medan trass är en vulkanisk aska som kan utvinnas. Utöver den positiva miljöeffekten som erhålls när alternativa bindemedel ersätter cementklinker, så har de alternativa bindemedlen andra egenskaper, både positiva och negativa, som påverkar betongen. Målet med denna studie var att undersöka och jämföra om betongblandningar där en del av cementklinkern har ersatts med alternativa bindemedel når upp till de krav som ställs i nuvarande regelverk. Utöver det så undersöktes även hur betongblandningarnas materialparametrar påverkades av alternativa bindemedel. Betongblandningarna delades in i tre olika typer av betong: betong för broar (vct 0.4), vattenbyggnader (vct 0.45) och vindkraftverksfundament (vct 0.55), där totalt sju betongblandningar tillverkades i ett laboratorium. Betongblandningarna undersöktes i de tre olika faserna för hårdnande av betong, vilka är färsk, ung och hårdnad betong. De materialparametrar som analyserades var tryckhållfasthet, krympning, frostresistens, arbetbarhet, luftporhalt och temperaturutveckling. Förutom de experimentella testerna gjordes en jämförelse kring hur mycket koldioxid som kan reduceras för varje betongblandning, jämfört med en referensbetong för varje användningsområde. Betongblandningen med ett CEM II/A-V flygaska-cement och 15% GGBS visade stor potential med avseende på de olika materialparametrarna. Denna blandning är dock enligt svensk standard inte möjlig att certifiera för betongbyggnad i exponeringsklass XF4, exempelvis broar, men kan certifieras för betongbyggnad i exponeringsklass XF3, exempelvis fundament för vindkraftverk. Blandningen med 30% GGBS och 5% silikastoft visade även positiva egenskaper, men flyttillsatsmedel måste användas i denna blandning för att erhålla en god arbetbarhet. För vattenbyggnadsbetong så visade blandningen med 35% GGBS en hög tryckhållfasthet, men samtidigt en hög temperaturutveckling och en låg arbetbarhet. Blandningen med trass hade en noterbart låg temperaturutveckling, men med ökad krympning samt låg arbetbarhet. Avslutningsvis så uppvisade alla blandningar en frostresistens som enligt standard klassificeras som ”Mycket bra”.