Neste trabalho são apresentados os resultados do desenvolvimento e teste de esquemas upwind de alta resolução para o controle da difusão numérica em leis de conservação gerais e problemas em dinâmica dos fluidos. Em particular, são derivados dois novos esquemas: o ALUS (Adaptive Linear Upwind Scheme) e o TOPUS (Third-Order Polynomial Upwind Scheme). Esses esquemas são testados no transporte de escalares, em equações 1D tipo convecção-difusão, em sistemas hiperbólicos 1D, nas equações de Euler 2D da dinâmica dos gases e nas equações de Navier-Stokes incompressíveis 2D/3D. Os esquemas são então associados a uma modelagem algébrica não linear para a simulação de problemas de escoamentos incompressíveis turbulentos 2D com/sem superfícies livres / In this work, results of the development and testing of high-resolution upwind schemes for controlling of the numerical diffusion for general conservation laws and fluid dynamics problems are presented. In particular, two new high-resolution upwind schemes are derived, namely, the ALUS (Adaptive Linear Upwind Scheme) and the TOPUS (Third-Order Polynomial Upwind Scheme). These schemes are tested in scalar transport, 1D convection-diffusion equations, 1D hyperbolic systems, 2D Euler equations of the gas dynamics, and in 2D/3D incompressible Navier-Stokes equations. The schemes are then combined with a nonlinear Reynolds stress algebraic equation model for the simulation of 2D incompressible turbulent flows with/without free surfaces

This paper covers information research of basic design rules of industrial wet sumps. It describes mathematical models of vortices and method for their identification and visualization. Then the author focuses on CFD modeling of surface vortices with single phase and multiphase approach with Volume of Fluid method. Basic principles of multiphase CFD modelling in OpenFOAM and ANSYS Fluent are given. Description and benchmarking of suitable turbulence models is also present. The single phase and multiphase approach were successfully validated for a simple test case of bathtub surface vortex. Satisfactory agreement with experimental data was achieved. The accuracy and behavior of both solvers were compared between each other. This gives us useful tool for evaluation of inflow condition and danger of surface vortex occurrence in wet sumps. The acquired knowledges were used to design an experimental test case with geometry similar to industrial wet sump. A map of surface vortex occurrence has been created for different operating points. One of the operating point has been used for numerical simulation (both single phase and multiphase). Partial agreement with experimental observation has been achieved.

Detta examensarbete undersöker möjligheten att tillämpa tidiga och ej så beräkningstunga CFD-simuleringar (’Computational Fluid Dynamics’) för optimering av gasväxlingskomponenter tidigt i produktutvecklingsprocessen. Examensarbetet har innefattat framtagande av generellt applicerbara inställningar och riktlinjer vid modellering av gasväxlingskomponenter med programvaran OpenFOAM, optimerade för att nyttja så låg beräkningskraft som möjligt men fortfarande erhålla tillräckligt noggranna och pålitliga resultat. Rapporten ger en teoretiskt genomlysning med motivering av simuleringsrelaterade val i OpenFOAM i syfte att validera och efter behov justera de inställningar och parameterval ansatta i det befintliga Excel skriptet – framtaget av avdelningen med ansvar för avgasefterbehandlingssystem – som automatiserar uppställningen av OpenFOAM:s simuleringsrelaterade filstruktur. Detta i syfte att erhålla och säkerställa pålitliga resultat vid användning av skriptet anpassat för simulering av gasväxlingskomponenter. Rapporten redovisar även bakomliggande analyser för olika inställningar och val i OpenFOAM i syfte att tjäna som välgrundade riktlinjer genom hela CFD-processen; såsom för skapande av geometriska modeller, generering av volymsnät, åtgärder för att säkerställa konvergens samt uppställning och tolkning av resultatet. En av examensarbetets leveranser är en metodbeskrivning utformad med praktiska riktlinjer för genomförandet av hela CFD-processen med avsedda programvaror samt med tillhörande praxis avseende simuleringsrelaterade val genom processen. Ett antal genomförda fallstudier i examensarbetet visar att OpenFOAM har potential att utföra initiala och indikativa simuleringar för att mer tidseffektivt möjliggöra en bredare idégenerering i konceptutvecklingsfasen. / This thesis investigates the possibility of applying early and not so computational heavy simulations using Computational Fluid Dynamics (CFD) for optimization of gas exchange components early in the product development process. The scope of the thesis includes the development of generally applicable settings and guidelines – documented in a methodology – when modelling gas exchange components with the software OpenFOAM, optimized to use as low computational power as possible but still obtaining sufficiently accurate and reliable data. The report consists of a theoretical study and motives for simulation-related choices in OpenFOAM in order to adjust and validate the settings and parameter choices applied in the existing Excel script – developed by the department responsible for exhaust aftertreatment systems – that automates the set-up of OpenFOAM's simulation-related file structure. This in order to obtain and ensure reliable results using the script adapted to the environment for gas exchange components. The report also presents underlying analyses for different settings and choices in order to serve as well-founded guidelines throughout the CFD-process; such as the creation of geometric models, the generation of mesh, measures to ensure convergence, and the set-up and interpretation of the results. One of the deliverables of the thesis is a method description designed with practical guidelines for the entire CFD-process with intended software’s and with associated best practices in regards of simulation-related choices throughout the process. A number of case studies – that has been simulated in this thesis – show that OpenFOAM has the potential to perform initial and indicative simulations enabling a more time-efficiently and broader ideation in the concept development phase.