The Azeri, Chirag, Gunashli (ACG) field is located offshore Azerbaijan. The reservoirs are multilayered sandstones forming traps within a major anticlinal structure. Proven crude oil reserves are estimated to contain 5.4 billion barrels of oil. In the past this area has been studied in regional detail but not at the reservoir scale with respect to the fluvio-deltaic sediments filling the northern shore of the ancient South Caspian Sea. The aim of this study is carried out the sedimentological, cyclostratigraphical analysis and reservoir characterization of Balakhany X Formation within the Productive Series which is considered to be one of the significant producing horizons. To be able to achieve this objective, a 30m thick section, which is mainly composed of siliciclastics, has been studied in detail on Balakhany X cores from C01 well Azeri field. In this study, detailed lithofacies analyses were performed and sandstone, mudstone, siltstone facies were recognized in the studied interval of the Balakhany X Formation. Litharenites and sublitharenites sandstones are the most abundant in the succession. Sedimentological analysis such as grain-size sphericity, provenance, XRD, SEM and grain surface texture were performed and their relationship with depositional environment were discussed. The grain size distribution of the samples along the succession shows distribution of fine to very fine sands. Sorting of sandstones ranges between moderately well to very well sorted. The provenance analysis of sandstones based on modal analysis of thin sections related to recycled orogen. According to interpretation of grain size parameters and grain surface textures analysis the main transporting agent of sands observed as wind, wave and river agents. High resolution cyclostratigraphy studies based on cm-m scaled cyclic occurrences of lithofacies along the measured section were performed. Milankovitch, sub-Milankovitch and millennial cycles were determined along the studied section. The petrophysical analysis revealed good to very good (18 to 24%) porosity and good permeability (10 to 538mD) in Balakhany X Formation. The porosity and permeability are affected by both textural and compositional controls. Grain size distribution along the reservoir section is fine to very fine sands. Influence of compaction was observed by the fractures and dissolutions on the sand grains. The calcite cement, grain-size variation, sorting and compaction are the main factors controlling porosity and permeability.

Expansive soils occurring in arid and semi-arid climate regions of the world cause serious problems on civil engineering structures. Such soils swell when given an access to water and shrink when they dry out. Several attempts are being made to control the swell-shrink behavior of these soils. Soil stabilization using chemical admixtures is the oldest and most widespread method of ground improvement. In this study, waste limestone dust and waste dolomitic marble dust, by-products of marble industry, were used for stabilization of expansive soils. The expansive soil is prepared in laboratory as a mixture of kaolinite and bentonite. Waste limestone dust and waste dolomitic marble dust were added to the expansive soil with predetermined percentage of stabilizer varying from 0 to 30 percent. Grain size distribution, consistency limits, chemical and mineralogical composition, swelling percentage, and rate of swell were determined for the samples. Swelling percentage decreased and rate of swell increased with increasing stabilizer percentage. Also, samples were cured for 7 days and 28 days before applying swell tests. Curing of samples affects swell percentages and rate of swell in positive way.

ABSTRACT THE EFFECT OF GROUP BEHAVIOR ON THE PULL-OUT CAPACITY OF SOIL NAILS IN HIGH PLASTIC CLAY Ak&amp / #56256 / &amp / #56533 / &amp / #56256 / &amp / #56570 / , Ebru Ph. D., Department of Civil Engineering Supervisor : Assoc. Prof. Dr. B. Sad&amp / #56256 / &amp / #56533 / k Bak&amp / #56256 / &amp / #56533 / r Co-Supervisor : Asst. Prof. Dr. M. Tolga Y&amp / #56256 / &amp / #56533 / lmaz September 2009, 161 pages Soil nailing technique is widely used in stabilizing roadway and tunnel portal cut excavations. The key parameter in the design of soil nail systems is the pull-out capacity. The pull-out capacity of the soil nails can be estimated from the studies involving similar soil conditions or can be estimated from the empirical formulas. Field verification tests are performed before the construction stage in order to confirm the parameter chosen in the design of soil nailing system. It is reported in the literature that, the pull-out resistance of a soil nail in sand should be reduced for the nails installed closer than a specific minimum distance, whereas no such requirement have been discussed for nail groups in clays. v In this study, the pull-out resistance of nails in high plastic clay are tested to investigate the influence of nail spacing in group applications. The laboratory set-up for the pull-out tests is composed of an aluminum model box (300mm (w) x 300mm (h) x 500 mm (l)), soil sample, reinforcements, pull-out device, overburden pressure applicator and monitoring device. A series of pull-out tests has been carried out on single nails and group of nails with spacings 2 and 6 times the diameter of a nail in order to observe the group effect on the pullout capacity of the nails. The nails are located into their positions during the placement of clay into the box. Within the limitations of this study, it is observed that, there is a reduction in the pull-out capacity of the central nail in 2&Oslash / spaced group. The pull-out capacity of the central nail in nail group with 6&Oslash / spacing, is not affected from the neighboring nails. In all tests, the plots of pull-out load on nail versus nail displacement show that, the peak value of load is followed by a sharp reduction. The peak pull-out load is mobilized at first few millimeters of the nail displacements. A 3D finite element program is used for numerical analyses of the experiments. The measured pull-out capacity of the soil nails are compared by the results of simulated forces obtained from these analyses. By and large, the agreement between the tests and the numerical analyses is observed to be satisfactory. The details of the numerical models are briefly presented in order to give insight into numerical modeling of soil nails in real applications.

Turkey is one of the most earthquake prone countries in the world. The study area, Erbaa, is located in a seismically active fault zone known as North Anatolian Fault Zone (NAFZ). Erbaa is one of the towns of Tokat located in the Middle Black Sea Region. According to the Earthquake zoning map of Turkey, the study area is in the First Degree Earthquake Zone. The city center of Erbaa (Tokat) was previously settled on the left embankment of Kelkit River. After the disastrous 1942 Niksar-Erbaa earthquake (Mw = 7.2), the settlement was moved southwards. From the period of 1900s, several earthquakes occurred in this region and around Erbaa. The 1942 earthquake is the most destructive earthquake in the center of Erbaa settlement. In this study, the geological and geotechnical properties of the study area were investigated by detailed site investigations. The Erbaa settlement is located on alluvial and Pliocene deposits. The Pliocene clay, silt, sand, and gravel layers exist in the southern part of Erbaa. Alluvium in Erbaa region consists of gravelly, sandy, silty, and clayey layers. The alluvial deposits are composed of stratified materials of heterogeneous grain sizes, derived from various geological units in the vicinity. The main objective of this study is to prepare a seismic microzonation map of the study area for urban planning purposes since it is getting more essential to plan new settlements considering safe development strategies after the disastrous earthquakes. In this respect, seismic hazard analyses were performed to deterministically assess the seismic hazard of the study area. Afterwards, the essential ground motions were predicted regarding near fault effects as the study area is settled on an active fault zone. 1-D equivalent linear site response analyses were carried out to evaluate the site effects in the study area. Amplification values obtained from site response analyses reveal that the soil layers in the study area is quite rigid. Furthermore, liquefaction potential and post liquefaction effects including lateral spreading and vertical settlement were also delineated for the study area. The above-mentioned parameters were taken into account in order to prepare a final seismic microzonation map of the study area. The layers were evaluated on the basis of overlay methodologies including Multi-Criteria Decision Analysis (MCDA). Two different MCDA techniques, Simple Additive Weighting (SAW) and Analytical Hierarchical Process (AHP), were carried out in GIS environment. The seismic microzonation maps prepared by SAW and AHP methods are compared to obtain a final seismic microzonation map. Finally, the map derived from the AHP method is proposed to be the final seismic microzonation map of Erbaa. As an overall conclusion, the northwestern part of the study area where the loose alluvial units exist is found to be vulnerable to earthquake-induced deformations. On the other hand, the Pliocene units in the southern and alluvial units in the northeastern part are quite resistant to earthquake effects. In addition, the proposed final seismic microzonation map should be considered by urban planners and policy makers during urban planning projects in Erbaa.

Fluid migration behind the cased holes is an important problem for oil and gas industry both considering short terms and long terms after cementing operation. For many reasons like high formation pressures, high shrinkage rate of cement slurry while setting, lack of mechanical seal, channeling due to cement slurry setting profile, hydrocarbon migration may occur and lead expensive recompletion operations and sometimes abandonment. Solutions to this problem vary including high density-low fluid loss cement slurry or right angle cement setting profile. During this study, the effect of &ldquo / free water&rdquo / which is the basic quality property of API G class cement, on fluid migration potential has been tested for different samples and in combination with different physical conditions. For this study API G class cements have been used. In order to justify the quality of each cement sample standard API G class quality tests were conducted. Moreover, as a main instrument &ldquo / Static Gel Strength Analyzer&rdquo / is used to measure the static gel strength of cement slurry and how long it takes to complete transition time. Bolu cement, Nuh cement, and Mix G cement samples were tested according to their free fluid values which are %2.5, %5, %3.12 respectively, and it is found that the Bolu cement with lowest free fluid content has the lowest potential for fluid migration. As a conclusion, fluid migration through behind the cased hole is a major threat for the life of the well. Appropriate cement slurry system may easily defeat this threat and lead cost saving well plans. Key words: Fluid migration, fluid loss, transition time, channeling, right angle, API G class cement, free water, high formation pressure

ABSTRACT IMPROVEMENT OF BEARING CAPACITY OF A SOFT SOIL BY THE ADDITION OF FLY ASH &Ouml / ZDEMIR, Murat Aziz M.Sc., Department of Civil Engineering Supervisor : Prof. Dr. Erdal &Ccedil / OK&Ccedil / A Co-Supervisor : Assoc. Prof. Dr. Murat G&Uuml / LER May 2011, 119 pages Soft soils are not suitable for use in runway and highway construction due to their undesirable characteristics such as poor grading, low strength, excessive plasticity, tendency to shrink or swell. By stabilizing such soils with appropriate agents, their engineering properties can be improved. One of the stabilizing agents is Class C fly ash. This study aimed at investigation of bearing capacity improvement of a soft soil (from Elmadag area) by using Class C fly ash (from Soma Thermal Power Plant). In the experimental study, index properties of soft soil and fly ash stabilized samples are determined. Then modified Proctor compaction, soaked California Bearing Ratio, and Unconfined Compressive Strength characteristics of the samples are investigated. During the study, the stabilized soil samples are prepared at different fly ash contents, i.e., 0%, 3%, 5%, 7%, and 10%. The samples are subjected to soaked California Bearing Ratio tests after 0, 7, and 28 days of curing. In addition to California Bearing Ratio tests, Unconfined Compressive Strength tests with 0, 7, and 28 days of curing are performed samples. For comparison purpose, hydrated lime is also used instead of fly ash in Unconfined Compressive Strength tests at predetermined contents, i.e., 3%, 5%, and 7%. In order to observe microstructures of samples, Scanning Electron Microscope - Energy Dispersive X-ray analysis are performed. The results of the study show that bearing capacity of Elmadag soft soil can be improved substantially and swell can be reduced significantly by using Class C fly ash.

Seismic safety of underground structures (culvert, subway, natural gas and water sewage systems) plays a major role in sustainable public safety and urban development. Very few experimental data are currently available and there is not generally accepted procedure to estimate the dynamic pressures acting on underground structures. This study aims to enhance the state of prevalent information necessary in understanding the dynamic behavior of box culverts and the stresses acting under dynamic excitations through experimental analyses. For this purpose, a series of shaking table tests were conducted on box-type culverts buried in dry sand. To simulate the free-field boundary conditions, a laminar box was designed and manufactured for use in a 1-g shake table. Four culvert models having different rigidities were tested under various harmonic motions in order to examine the effect of flexibility ratio on dynamic lateral soil pressures. Based on the tests results, a simplified dynamic pressure distribution acting on sidewalls of the culvert model was suggested. Then, a dynamic lateral coefficient was defined for the proposed peak pressure value in the distribution. The values of this coefficient were obtained as a function of shear strain and relative stiffness between the soil and underground structure. Finally, a simplified frame analysis approach was suggested for the assessment of the forces on the structure, to help to carry out a preliminary design of box-type culverts. In this approach, it was assumed that the culvert was fixed at bottom and subjected to lateral stresses on sidewalls and shear stresses on the upper face. For the confirmation of the method, centrifuge tests were conducted on a box-type culvert model under the Seventh Framework Programme of European Union with Grant Agreement No.227887. Results show that the proposed simplified procedure can be used in reasonable accuracy as a practical approach for the preliminary assessment of box-type culverts buried in dry sand under seismic action.

Static and dynamic interaction mechanism of the retained soil-compressible geofoam buffer and yielding retaining structures requires further investigation. The present study, initiated on this motive, discusses the results of 1-g physical model tests and numerical analyses of cantilever retaining walls with and without deformable geofoam buffers between the wall and cohesionless granular backfill. 0.7m high walls with various wall thicknesses were utilized in the physical modeling. Dynamic tests were carried out by using a laminar container placed on a uni-axial shaking table. Influence of buffer thickness, geofoam type and wall flexibility as well as base excitation characteristics on the lateral earth pressures and flexural wall deflections were under concern. Outcomes of the analyses performed with FLAC-2D (v6.0) finite difference code were validated against the results of the physical model tests. It was observed that the arching effect induced in the retained soil by the lateral compression of the lower half of the geofoam buffer has a positive effect, as this zone is able to absorb a portion of the total unbalanced lateral force exerted by the backfill thus causing a reduction in the static and seismic lateral wall pressures. Relative thickness and stiffness of the geofoam buffer appear to be the most dominant factors affecting the reduction in earth thrust. Lateral earth pressure coefficients determined from physical model tests were compared with those calculated using methods available in the literature. Good agreement was observed between the predictions. Graphs were provided to estimate the static and dynamic lateral earth pressure coefficients for various combinations of wall stiffness and buffer characteristics. Analysis of a 6m high prototype cantilever wall subjected to an excitation recorded in August 17, 1999 Kocaeli earthquake by finite difference method exhibited the contribution of geofoam buffers on seismic performance of cantilever earth retaining walls. It was observed that the presence of an EPS geofoam inclusion provides a reduction of the permanent flexural wall deflections as well as total seismic thrust likely to be experienced by the wall during an earthquake.

The primary objective of this study is to evaluate the seismic hazard in the Eastern Marmara Region using improved seismic source models and enhanced ground motion prediction models by probabilistic approach. Geometry of the fault zones (length, width, dip angle, segmentation points etc.) is determined by the help of available fault maps and traced source lines on the satellite images. State of the art rupture model proposed by USGS Working Group in 2002 is applied to the source system. Composite reoccurrence model is used for all seismic sources in the region to represent the characteristic behavior of North Anatolian Fault. New and improved global ground motion models (NGA models) are used to model the ground motion variability for this study. Previous studies, in general, used regional models or older ground motion prediction models which were updated by their developers during the NGA project. New NGA models were improved in terms of additional prediction parameters (such as depth of the source, basin effects, site dependent standard deviations, etc.), statistical approach, and very well constrained global database. The use of NGA models reduced the epistemic uncertainty in the total hazard incorporated by regional or older models using smaller datasets. The results of the study is presented in terms of hazard curves, deaggregation of the hazard and uniform hazard spectrum for six main locations in the region (Adapazari, Duzce, Golcuk, Izmit, Iznik, and Sapanca City Centers) to provide basis for seismic design of special structures in the area. Hazard maps of the region for rock site conditions at the accepted levels of risk by Turkish Earthquake Code (TEC-2007) are provided to allow the user perform site-specific hazard assessment for local site conditions and develop site-specific design spectrum. Comparison of TEC-2007 design spectrum with the uniform hazard spectrum developed for selected locations is also presented for future reference.

Rock slope stability is considered as one of the most important fields in rock engineering. Developments of computation facilities and increase in application of sophisticated mathematical concepts in engineering problems have also affected the methods of slope stability analysis. In recent years, the numerical modeling methods have extensively applied instead of limit equilibrium methods. Also, the probabilistic methods are considered in rock slope designs to quantify the uncertainties of input effecting variables. In this research, a probabilistic-numerical approach was developed by integration of three dimensional Distinct Element Method (DEM) and probabilistic approach to analyze the stability of discontinuous rock slopes. Barton models have been used to model the behavior of rock discontinuities and the shear strain was considered as failure indicator of discontinuities. The proposed methodology was applied to a rock slope in Amasya, Turkey where the Joint Roughness Coefficient (JRC) was considered as the main random variable. The effect of basic friction angle and cohesion of joints infilling material and its strength reduction due to weathering were included in the analysis. In the slope the shearing behavior of fourteen discontinuities and the failure probability of each block were investigated, and the corresponding Reliability Index (&beta / ) was derived for each of the discontinuities.