With the explosive development of wireless communication systems the specifications of the supporting hardware platforms have become more and more demanding. According to the long term goals of the industry, future communications systems should integrate a wide variety of standards. This leads to the idea of software defined radio, implemented on fully reconfigurable hardware.Among other reconfigurable hardware blocks, suitable for the software radio concept, an outstanding importance belongs to the reconfigurable filters that are responsible for the selectivity of the system. The problematic of filtering is strictly connected to the architecture chosen for a multi-mode receiver realization. According to the chosen architecture, the filters can exhibit low pass or band pass frequency responses.The idea of reconfigurable frequency parameters has been introduced since the beginning of modern filtering applications due to the required precision of the frequency response. However, the reconfiguration of the parameters was usually done in a limited range around ideal values. The purpose of the presented research is to transform the classical filter structures with simple self-correction into fully reconfigurable filters over a wide range of frequencies. The ideal variation of the frequency parameters is continuous and consequently difficult to implement in real circuits. Therefore, it is usually sufficient to use a discrete programming template with reasonably small steps.There are several methods to implement variable frequency parameters. The most often used programming templates employ resistor and capacitor arrays, switched according to a given code. The low pass filter implementation proposed in this work uses a special switching template, optimized for a quasi-linear frequency variation over logarithmic axes. The template also includes the possibility to compensate errors caused by component tolerances and temperature. Another important topic concerns the implementation of programmable band pass filters, suitable for IF sampling receivers. The discussion is centered on the feasibility and the flexibility of different band pass filter architectures. Due to the high frequency requirements, the emphasis lays on filters that employ transconductance amplifiers and capacitors. / Die rasch fortschreitende Entwicklung drahtloser Kommunikationssysteme führt zu immer anspruchsvolleren Spezifikationen der diese Systeme unterstützenden Hardwareplattformen. Zukünftige Kommunikationssysteme sollen übereinstimmend mit den längerfristigen Zielen der Industrie verschiedene Standards integrieren. Dies führt zu der Idee von vollständig rekonfigurierbarer Hardware, welche mittels Software gesteuert wird.Inmitten anderer rekonfigurierbarer Hardwareblöcke, die für das Software Radio Konzept geeignet sind, besitzen die steuerbaren Filter, welche wesentlichen Einfluss auf die Selektivität des Systems haben, eine enorme Bedeutung. Die Filterproblematik ist eng mit der gewählten Architektur der standardübergreifenden Empfängerrealisierung verknüpft. Die Filter können entsprechend der ausgesuchten Architektur Tiefpass- oder Bandpasscharakter annehmen.Die Idee rekonfigurierbarer Frequenzparameter wurde bereits mit Beginn moderner Filteranwendungen auf Grund geforderter Frequenzganggenauigkeit umgesetzt. Jedoch wurde die Parameterrekonfiguration üblicherweise nur in einem begrenzten Bereich um die Idealwerte herum vorgenommen. Das Ziel der vorgestellten Forschungsarbeit ist es, diese klassischen Filterstrukturen mit einfacher Selbstkorrektur in über große Frequenzbereiche voll rekonfigurierbare Filter zu transformieren. Idealerweise werden die Frequenzparameter kontinuierlich variiert weswegen sich die Implementierung in reellen Schaltkreisen als schwierig erweist. Deshalb ist es üblicherweise ausreichend, ein diskretes Steuerschema mit kleinen Schrittweiten zu verwenden.Es gibt verschiedene Methoden, variable Frequenzparameter zu implementieren. Die meisten Schemata verwenden Widerstands- und Kondensatorfelder, die entsprechend eines Kodes geschaltet werden. Die in dieser Arbeit vorgestellte Implementierung eines Tiefpassfilters nutzt ein spezielles Umschaltschema, welches für die quasi-lineare Frequenzvariation bei Darstellung über logarithmischen Axen optimiert wurde. Es beinhaltet weiterhin die Möglichkeit, Fehler zu kompensieren, die durch Bauelementtoleranzen und Temperaturschwankungen hervorgerufen werden.Ein weiteres interessantes Thema betrifft die Implementierung steuerbarer Bandpassfilter, die für Empfänger mit Zwischenfrequenzabtastung geeignet sind. Die Betrachtung beschränkt sich hierbei auf die Durchführbarkeit und Flexibilität verschiedener Bandpassfilterarchitekturen. Auf Grund hoher Frequenzanforderungen liegt der Schwerpunkt auf Filtern, die auf Transkonduktanzverstärkern und Kondensatoren basieren.

LOW power operation for wireless radio receivers has been gaining importance lately on account of the recent spurt of growth in the usage of ubiquitous embedded mobile devices. These devices are becoming relevant in all domains of human influence. In most cases battery life for these devices continue to be an us-age bottleneck as energy storage techniques have not kept pace with the growing demand of such mobile computing devices. Many applications of these radios have limitations on recharge cycle, i.e. the radio needs to last out of a battery for long duration. This will specially be true for sensor network applications and for im-plantable medical devices. The search for low power wireless receivers has become quite advanced with a plethora of techniques, ranging from circuit to architecture to system level approaches being formulated as part of standard design procedures. However the next level of optimization towards “Smart” receiver systems has been gaining credence and may prove to be the next challenge in receiver design and de-velopment. We aim to proceed further on this journey by proposing Power Scalable Wireless Receivers (PSRX) which have the capability to respond to instantaneous performance requirements to lower power even further. Traditionally low power receivers were designed for worst-case input conditions, namely low signal and high interference, leading to large dynamic range of operation which directly im-pacts the power consumption. We propose to take into account the variation in performance required out of the receiver, under varying Signal and Interference conditions, to trade-off power. We have analyzed, designed and implemented a Power Scalable Receiver tar-geted towards low data-rate receivers which can work for Zigbee or Bluetooth Low Energy (BLE) type standards. Each block of such a receiver system was evaluated for performance-power trade-offs leading to identification of tuning/control knobs at the circuit architecture level of the receiver blocks. Then we developed an usage algorithm for finding power optimal operational settings for the tuning knobs, while guaranteeing receiver reception performance in terms of Bit-Error-Rate (BER). We have proposed and demonstrated a novel signal measurement system to gen-erate digitized estimates of signal and interference strength in the received signal, called Received Signal Quality Indicator (RSQI). We achieve a RSQI average energy consumption of 8.1nJ with a peak energy consumption of 9.4nJ which is quite low compared to the packet reception energy consumption for low power receivers, and will be substantially lower than the energy savings which will be achieved from a power scalable receiver employing a RSQI. The full PSRX system was fabricated in UMC 130nm RF-CMOS process to test out our concepts and to formally quantify the power savings achieved by following the design methodology. The test chip occupied an area of 2.7mm2 with a peak power consumption of 5.5mW for the receiver chain and 18mW for the complete PSRX. We were able to meet the receiver performance requirements for Zigbee standard and achieved about 5X power savings for the range of input condition variations.

This research looks into the design of an integrated in-phase/quadrature (I/Q) VCO operating at 5 GHz. The goal is to design a phase shifter that is implemented at the LO used for RF up conversion. The target application for the phase shifter is towards phased array antennas operating at 5 GHz. Instead of designing multiple VCOs that each deliver a variety of phases, two identical LC-VCOs are coupled together to oscillate at the same frequency and deliver four outputs that are 90 ° out of phase. By varying the amplitudes of the in-phase and quadrature signals independently using VGAs before adding them together, a resultant out-of-phase signal is obtained. A number of independently variable out-of-phase signals can be obtained from these 90 ° out-of-phase signals and this technique is better known as the vector sum method of phase shifting. Control signals to the inputs of the VGAs required to obtain 22.5 ° phase shifts were designed from simulations and are generated using 16-bit DACs. The design is implemented and manufactured using a 0.35 µm SiGe BiCMOS process and the complete prototype IC occupies an area of 2.65 × 2.65 mm2. The I/Q VCO with 360 ° variable phase outputs occupies 1.10 × 0.85 mm2 of chip area and the 16-bit DAC along with its decoding circuitry occupies 0.41 × 0.13 mm2 of chip area. The manufactured quadrature VCO was found to oscillate between 4.12 ~ 4.74 GHz and consumes 23.1 mW from a 3.3 V supply without its buffer circuitry. A maximum phase noise of -78.5 dBc / Hz at a 100 kHz offset and -108.17 dBc / Hz at a 1 MHz offset was measured and the minimum VCO figure of merit is 157.8 dBc / Hz. The output voltages of the 16 bit DAC are within 3.5 % of the design specifications. When the phase shifter is controlled by the 16 DAC signals, the maximum measured phase error of the phase shifter is lower than 10 %. / Dissertation (MEng)--University of Pretoria, 2009. / Electrical, Electronic and Computer Engineering / unrestricted

With the explosive development of wireless communication systems the specifications of the supporting hardware platforms have become more and more demanding. According to the long term goals of the industry, future communications systems should integrate a wide variety of standards. This leads to the idea of software defined radio, implemented on fully reconfigurable hardware.Among other reconfigurable hardware blocks, suitable for the software radio concept, an outstanding importance belongs to the reconfigurable filters that are responsible for the selectivity of the system. The problematic of filtering is strictly connected to the architecture chosen for a multi-mode receiver realization. According to the chosen architecture, the filters can exhibit low pass or band pass frequency responses.The idea of reconfigurable frequency parameters has been introduced since the beginning of modern filtering applications due to the required precision of the frequency response. However, the reconfiguration of the parameters was usually done in a limited range around ideal values. The purpose of the presented research is to transform the classical filter structures with simple self-correction into fully reconfigurable filters over a wide range of frequencies. The ideal variation of the frequency parameters is continuous and consequently difficult to implement in real circuits. Therefore, it is usually sufficient to use a discrete programming template with reasonably small steps.There are several methods to implement variable frequency parameters. The most often used programming templates employ resistor and capacitor arrays, switched according to a given code. The low pass filter implementation proposed in this work uses a special switching template, optimized for a quasi-linear frequency variation over logarithmic axes. The template also includes the possibility to compensate errors caused by component tolerances and temperature. Another important topic concerns the implementation of programmable band pass filters, suitable for IF sampling receivers. The discussion is centered on the feasibility and the flexibility of different band pass filter architectures. Due to the high frequency requirements, the emphasis lays on filters that employ transconductance amplifiers and capacitors. / Die rasch fortschreitende Entwicklung drahtloser Kommunikationssysteme führt zu immer anspruchsvolleren Spezifikationen der diese Systeme unterstützenden Hardwareplattformen. Zukünftige Kommunikationssysteme sollen übereinstimmend mit den längerfristigen Zielen der Industrie verschiedene Standards integrieren. Dies führt zu der Idee von vollständig rekonfigurierbarer Hardware, welche mittels Software gesteuert wird.Inmitten anderer rekonfigurierbarer Hardwareblöcke, die für das Software Radio Konzept geeignet sind, besitzen die steuerbaren Filter, welche wesentlichen Einfluss auf die Selektivität des Systems haben, eine enorme Bedeutung. Die Filterproblematik ist eng mit der gewählten Architektur der standardübergreifenden Empfängerrealisierung verknüpft. Die Filter können entsprechend der ausgesuchten Architektur Tiefpass- oder Bandpasscharakter annehmen.Die Idee rekonfigurierbarer Frequenzparameter wurde bereits mit Beginn moderner Filteranwendungen auf Grund geforderter Frequenzganggenauigkeit umgesetzt. Jedoch wurde die Parameterrekonfiguration üblicherweise nur in einem begrenzten Bereich um die Idealwerte herum vorgenommen. Das Ziel der vorgestellten Forschungsarbeit ist es, diese klassischen Filterstrukturen mit einfacher Selbstkorrektur in über große Frequenzbereiche voll rekonfigurierbare Filter zu transformieren. Idealerweise werden die Frequenzparameter kontinuierlich variiert weswegen sich die Implementierung in reellen Schaltkreisen als schwierig erweist. Deshalb ist es üblicherweise ausreichend, ein diskretes Steuerschema mit kleinen Schrittweiten zu verwenden.Es gibt verschiedene Methoden, variable Frequenzparameter zu implementieren. Die meisten Schemata verwenden Widerstands- und Kondensatorfelder, die entsprechend eines Kodes geschaltet werden. Die in dieser Arbeit vorgestellte Implementierung eines Tiefpassfilters nutzt ein spezielles Umschaltschema, welches für die quasi-lineare Frequenzvariation bei Darstellung über logarithmischen Axen optimiert wurde. Es beinhaltet weiterhin die Möglichkeit, Fehler zu kompensieren, die durch Bauelementtoleranzen und Temperaturschwankungen hervorgerufen werden.Ein weiteres interessantes Thema betrifft die Implementierung steuerbarer Bandpassfilter, die für Empfänger mit Zwischenfrequenzabtastung geeignet sind. Die Betrachtung beschränkt sich hierbei auf die Durchführbarkeit und Flexibilität verschiedener Bandpassfilterarchitekturen. Auf Grund hoher Frequenzanforderungen liegt der Schwerpunkt auf Filtern, die auf Transkonduktanzverstärkern und Kondensatoren basieren.