This work assesses the feasibility of designing and implementing the wave rotor (WR), the pulse detonation engine (PDE) and the internal combustion wave rotor (ICWR) as part of novel Brayton cycles able to reduce emissions of future aircraft. The design and evaluation processes are performed using the simplified analytical solution of the devices as well as 1D-CFD models. A code based on the finite volume method is built to predict the position and dimensions of the slots for the WR and ICWR. The mass and momentum equations are coupled through a modified SIMPLE algorithm to model compressible flow. The code includes a novel tracking technique to ensure the global mass balance. A code based on the method of characteristics is built to predict the profiles of temperature, pressure and velocity at the discharge of the PDE and the effect of the PDEs array when it operates as combustion chamber of gas turbines. The detonation is modelled by using the NASA-CEA code as a subroutine whilst the method of characteristics incorporates a model to capture the throttling and non-throttling conditions obtained at the PDE's open end during the transient process. A medium-sized engine for business jets is selected to perform the evaluation that includes parameters such as specific thrust, specific fuel consumption and efficiency of energy conversion. The ICWR offers the best performance followed by the PDE; both options operate with a low specific fuel consumption and higher specific thrust. The detonation in an ICWR does not require an external source of energy, but the PDE array designed is simple. The WR produced an increase in the turbine performance, but not as high as the other two devices. These results enable the statement that a pressure rise combustion process behaves better than pressure exchangers for this size of gas turbine. Further attention must be given to the NOx emission, since the detonation process is able to cause temperatures above 2000 K while dilution air could be an important source of oxygen.

This work assesses the feasibility of designing and implementing the wave rotor (WR), the pulse detonation engine (PDE) and the internal combustion wave rotor (ICWR) as part of novel Brayton cycles able to reduce emissions of future aircraft. The design and evaluation processes are performed using the simplified analytical solution of the devices as well as 1D-CFD models. A code based on the finite volume method is built to predict the position and dimensions of the slots for the WR and ICWR. The mass and momentum equations are coupled through a modified SIMPLE algorithm to model compressible flow. The code includes a novel tracking technique to ensure the global mass balance. A code based on the method of characteristics is built to predict the profiles of temperature, pressure and velocity at the discharge of the PDE and the effect of the PDEs array when it operates as combustion chamber of gas turbines. The detonation is modelled by using the NASA-CEA code as a subroutine whilst the method of characteristics incorporates a model to capture the throttling and non-throttling conditions obtained at the PDE's open end during the transient process. A medium-sized engine for business jets is selected to perform the evaluation that includes parameters such as specific thrust, specific fuel consumption and efficiency of energy conversion. The ICWR offers the best performance followed by the PDE; both options operate with a low specific fuel consumption and higher specific thrust. The detonation in an ICWR does not require an external source of energy, but the PDE array designed is simple. The WR produced an increase in the turbine performance, but not as high as the other two devices. These results enable the statement that a pressure rise combustion process behaves better than pressure exchangers for this size of gas turbine. Further attention must be given to the NOx emission, since the detonation process is able to cause temperatures above 2000 K while dilution air could be an important source of oxygen.

Indiana University-Purdue University Indianapolis (IUPUI) / This study contributes to a better understanding of ignition by hot combustion gases which finds application in internal combustion chambers with pre-chamber ignition as well as in wave rotor engine applications. The experimental apparatus consists of two combustion chambers: a pre chamber that generates the transient hot jet of gas and a main chamber which contains the main fuel air blend under study. Variables considered are three fuel mixtures (Hydrogen, Methane, 50\% Hydrogen-Methane), initial pressure in the pre-chamber ranging from 1 to 2 atm, equivalence ratio of the fuel air mixture in the main combustion chamber ranging from 0.4 to 1.5, and initial temperature of the main combustion chamber mixture ranging from 297 K to 500 K. Experimental data makes use of 4 pressure sensors with a recorded sampling rate up to 300 kHz, as well as high speed Schlieren imaging with a recorded frame rate up to 20,833 frame per seconds. Results shows an overall increase in ignition delay with increasing equivalence ratio. High temperature of the main chamber blend was found not to affect hot jet ignition delay considerably. Physical mixing effects, and density of the main chamber mixture have a greater effect on hot jet ignition delay.

Indiana University-Purdue University Indianapolis (IUPUI) / Pressure wave supercharger is an application of wave rotor technology that utilizes compression waves produced by high-pressure engine exhaust gas to compress the fresh intake air within the channels. The phenomena within the wave rotor channels are governed by compression and expansion waves initiated when the channel ends are periodically exposed to differing pressure ports. Two incoming fluids are brought into contact for a very short amount of time to facilitate efficient energy and momentum transfer, thereby exchanging pressure dynamically between the fluids by means of unsteady pressure waves. Since the energy transfer is based on unsteady pressure waves, correct matching of waves and ports is essential for optimum results. Mistiming of the waves in the channels is detrimental to the efficient exchange of pressure and low-pressure exhaust scavenging, which ensures minimum exhaust gas recirculation. Due to varying speed and load conditions of the unit to be supercharged, it is not always possible to maintain the rotor speed constant at the design point. To mitigate the effects of wave mistiming due to varying speed, a well-designed combination of wall-pockets was used in Comprex® pressure wave supercharger. The wall-pockets are the recesses provided in the endplates of pressure wave superchargers to create necessary pressure zones at desired locations. This thesis details an extensive qualitative and computational investigation of the performance of pressure wave superchargers with pockets. Numerical simulations of pressure wave superchargers have been performed using the wave rotor analysis codes employed at the Combustion and Propulsion Research Laboratory at IUPUI. This work also pays close attention to inspecting the numerical schemes and modeling of different physical phenomena used in each code. A comparative verification of the wave rotor analysis codes has been conducted to ensure that the same fundamental numerical scheme is correctly implemented in each code. The issue of low-pressure scavenging has been demonstrated by simulating the four-port (pocketless) pressure wave supercharger operating at lower speeds. The wall-pockets have been modeled using a simple lumped volume technique. The gas state in the lumped volume of pockets is estimated using the continuity and energy equations such that the net mass and energy fluxes between each pocket and the wave rotor channels are close to zero. The lumped volume models of pockets have been implemented in the four-port wave rotor configurations to simulate the pressure wave superchargers with pockets. The simulation results show that the pockets assist to maintain sufficient pressure in the desired zones to facilitate proper low-pressure scavenging during lower rotor speed operations. The Comprex simulation results have been observed to be in good agreement with experimental data and qualitative analysis. Specific observations on the performance of each code and comprehensive simulation results have been presented.

<div>Pressure wave supercharger is an application of wave rotor technology that utilizes compression waves produced by high-pressure engine exhaust gas to compress the fresh intake air within the channels. The phenomena within the wave rotor channels are governed by compression and expansion waves initiated when the channel ends are periodically exposed to differing pressure ports. Two incoming fluids are brought into contact for a very short amount of time to facilitate efficient energy and momentum transfer, thereby exchanging pressure dynamically between the fluids by means of unsteady pressure waves. Since the energy transfer is based on unsteady pressure waves, correct matching of waves and ports is essential for optimum results. Mistiming of the waves in the channels is detrimental to the efficient exchange of pressure and low-pressure exhaust scavenging, which ensures minimum exhaust gas recirculation. Due to varying speed and load conditions of the unit to be supercharged, it is not always possible to maintain the rotor speed constant at the design point.</div><div>To mitigate the effects of wave mistiming due to varying speed, a well-designed combination of wall-pockets was used in Comprex® pressure wave supercharger. The wall-pockets are the recesses provided in the endplates of pressure wave superchargers to create necessary pressure zones at desired locations. This thesis details an extensive qualitative and computational investigation of the performance of pressure wave superchargers with pockets. Numerical simulations of pressure wave superchargers have been performed using the wave rotor analysis codes employed at the Combustion and Propulsion Research Laboratory at IUPUI. This work also pays close attention to inspecting the numerical schemes and modeling of different physical phenomena used in each code. A comparative verification of the wave rotor analysis codes has been conducted to ensure that the same fundamental numerical scheme is correctly implemented in each code. The issue of low-pressure scavenging has been demonstrated by simulating the four-port (pocketless) pressure wave supercharger operating at lower speeds. The wall-pockets have been modeled using a simple lumped volume technique. The gas state in the lumped volume of pockets is estimated using the continuity and energy equations such that the net mass and energy fluxes between each pocket and the wave rotor channels are close to zero. The lumped volume models of pockets have been implemented in the four-port wave rotor configurations to simulate the pressure wave superchargers with pockets. The simulation results show that the pockets assist to maintain sufficient pressure in the desired zones to facilitate proper low-pressure scavenging during lower rotor speed operations. The Comprex simulation results have been observed to be in good agreement with experimental data and qualitative analysis. Specific observations on the performance of each code and comprehensive simulation results have been presented.</div>

Indiana University-Purdue University Indianapolis (IUPUI) / Investigations of a constant-volume combustor ignited by a penetrating transient jet (a puff) of hot reactive gas have been conducted in order to provide vital data for designing wave rotor combustors. In a wave rotor combustor, a cylindrical drum with an array of channels arranged around the axis spins at a high rpm to generate high-temperature and high-pressure product gas. The hot-gas jet ignition method has been employed to initiate combustion in the channels. This study aims at experimentally investigating the ignition delay time of a premixed combustible mixture in a rectangular, constant-volume chamber, representing one channel of the wave rotor drum. The ignition process may be influenced by the multiple factors: the equivalence ratio, temperature, and the composition of the fuel mixture, the temperature and composition of the jet gas, and the peak mass flow rate of the jet (which depends on diaphragm rupture pressure). In this study, the main mixture is at room temperature. The jet composition and temperature are determined by its source in a pre-chamber with a hydrogen-methane mixture with an equivalent ratio of 1.1, and a fuel mixture ratio of 50:50 (CH4:H2 by volume). The rupture pressure of a diaphragm in the pre-chamber, which is related to the mass flow rate and temperature of the hot jet, can be controlled by varying the number of indentations in the diaphragm. The main chamber composition is varied, with the use of four equivalence ratios (1.0, 0.8, 0.6, and 0.4) and two fuel mixture ratios (50:50, and 30:70 of CH4:H2 by volume). The sudden start of the jet upon rupture of the diaphragm causes a shock wave that precedes the jet and travels along the channel and back after reflection. The shock strength has an important role in fast ignition since the pressure and the temperature are increased after the shock. The reflected shock pressure was examined in order to check the variation of the shock strength. However, it is revealed that the shock strength becomes attenuated compared with the theoretical pressure of the reflected shock. The gap between theoretical and measured pressures increases with the increase of the Mach number of the initial shock. Ignition delay times are obtained using pressure records from two dynamic pressure transducers installed on the main chamber, as well as high-speed videography using flame incandescence and Schileren imaging. The ignition delay time is defined in this research as the time interval from the diaphragm rupture moment to the ignition moment of the air/fuel mixture in the main chamber. Previous researchers used the averaged ignition delay time because the diaphragm rupture moment is elusive considering the structure of the chamber. In this research, the diaphragm rupture moment is estimated based on the initial shock speed and the longitudinal length of the main chamber, and validated with the high-speed video images such that the error between the estimation time and the measured time is within 0.5%. Ignition delay times decrease with an increase in the amount of hydrogen in the fuel mixture, the amount of mass of the hot-jet gases from the pre-chamber, and with a decrease in the equivalence ratio. A Schlieren system has been established to visualize the characteristics of the shock wave, and the flame front. Schlieren photography shows the density gradient of a subject with sharp contrast, including steep density gradients, such as the flame edge and the shock wave. The flame propagation, gas oscillation, and the shock wave speed are measured using the Schlieren system. An image processing code using MATLAB has been developed for measuring the flame front movement from Schlieren images. The trend of the maximum pressure in the main chamber with respect to the equivalence ratio and the fuel mixture ratio describes that the equivalence ratio 0.8 shows the highest maximum pressure, and the fuel ratio 50:50 condition reveals lower maximum pressure in the main chamber than the 30:70 condition. After the combustion occurs, the frequency of the pressure oscillation by the traversing pressure wave increases compared to the frequency before ignition, showing a similar trend with the maximum pressure in the chamber. The frequency is the fastest at the equivalence ratio of 0.8, and the slowest at a ratio of 0.4. The fuel ratio 30:70 cases show slightly faster frequencies than 50:50 cases. Two different combustion behaviors, fast and slow combustion, are observed, and respective characteristics are discussed. The frequency of the flame front oscillation well matches with that of the pressure oscillation, and it seems that the pressure waves drive the flame fronts considering the pressure oscillation frequency is somewhat faster. Lastly, a feedback mechanism between the shock and the flame is suggested to explain the fast combustion in a constant volume chamber with the shock-flame interactions.

Indiana University-Purdue University Indianapolis (IUPUI) / This study contributes to a better working knowledge of the equipment being used in a well-established combustion lab. In particular, several constant-volume combustion properties (e.g., time ignition delay, flame propagation, and more) are examined to deduce any buoyancy effects between fuel and air mixtures and to develop a method aimed at minimizing such effects. This study was conducted on an apparatus designed to model the phenomena occurring within a single channel of a wave rotor combustor, which consists of a rotating cylindrical pre-chamber and a fixed rectangular main combustion chamber. Pressure sensors monitor the internal pressures within the both chambers at all times, and two slow-motion videography techniques visually capture combustion phenomena occurring within the main chamber. A new recirculation pump system has been implemented to mitigate stratification within the chamber and produce more precise, reliable results. The apparatus was used in several types of experiments that involved the combustion of various hydrocarbon fuels in the main chamber, including methane, 50%-50% methane-hydrogen, hydrogen, propane, and 46.4%-56.3% methane-argon. Additionally, combustion products created in the pre-chamber from a 1.1 equivalence ratio reaction between 50%-50% methane-hydrogen and air were utilized in the issuing pre-chamber jet for all hot jet ignition tests. In the first set of experiments, a spark plug ignition source was used to study how combustion events travel through the main chamber after different mixing methods were utilized – specifically no mixing, diffusive mixing, and pump circulation mixing. The study reaffirmed that stratification between fuel-air mixtures occurs in the main chamber through the presence of asymmetrical flame front propagation. Allowing time for mixing, however, resulted in more symmetric flame fronts, broader pressure peaks, and reduced combustion time in the channel. While 30 seconds of diffusion helped, it was found that 30 seconds of pumping (at a rate of 30 pumps per 10 seconds) was the most effective method at reducing stratification effects in the system. Next, stationary hot jet ignition experiments were conducted to compare the time between jet injection and main chamber combustion and the speed of the resulting shockwaves between cases with no mixing and 30 seconds of pump mixing. Results continued to show an improvement with the pump cases; ignition delay times were typically shorter, and shock speeds stayed around the same, if not increased slightly. These properties are vital when studying and developing wave rotor combustors, and therefore, reducing stratification (specifically by means of a recirculation system) should be considered a crucial step in laboratory models such as this one. Lastly, experiments between a fueled main chamber and rotating pre-chamber helped evaluate the leakage rate of the traversing hot jet ignition experimental setup paired with the new pump system. In its current form, major leaks are inevitable when attempting traversing jet experiments, especially with the pump’s suction action drawing sudden large plumes of outside air into the main chamber. To minimize leaks, gaps between the pre-chamber and main chamber should be reduced, and the contact surface between the two chambers should be more evenly distributed. Also, the pump system should only be operated as long as needed to evenly distribute the fuel-air mixture, which approximately happens when the main chamber’s total volume has been circulated through the system one time. Therefore, a new pump system with half of the original system’s volume was developed in order to decrease the pumping time and lower the risk of leaks.

Indiana University-Purdue University Indianapolis (IUPUI) / Testing of a wave-rotor constant-volume combustor (WRCVC) showed the viability of the application of wave rotors as a pressure gain combustor. The aero-thermal design of the WRCVC rig had originally been performed with a time-dependent, one-dimensional model which applies a single-step reaction model for the combustion process of the air-fuel mixture. That numerical model was validated with experimental data with respect of matching the flame propagation speed and the pressure traces inside the passages of the WRCVC. However, the numerical model utilized a single progress variable representing the air-fuel mixture, which assumes that fuel and air are perfectly mixed with a uniform concentration; thus, limiting the validity of the model. In the present work, a two-step reaction model is implemented in the combustion model with four species variables: fuel, oxidant, intermediate and product. This combustion model is developed for a more detailed representation for the combustion process inside the wave rotor. A two-step reaction model presented a more realistic representation for the stratified air-fuel mixture charges in the WRCVC; additionally it shows more realistic modeling for the partial combustion process for rich fuel-air mixtures. The combustion model also accounts for flammability limits to exert flame extinction for non-flammable mixtures. The combustion model applies the eddy-breakup model where the reaction rate is influenced by the turbulence time scale. The experimental data currently available from the initial testing of the WRCVC rig is utilized to calibrate the model to determine the parameters, which are not directly measured and no directly related practice available in the literature. A prediction of the apparent ignition the location inside the passage is estimated by examination of measurements from the on-rotor instrumentations. The incorporation of circumferential leakage (passage-to-passage), and stand-off ignition models in the numerical model, contributed towards a better match between predictions and experimental data. The thesis also includes a comprehensive discussion of the governing equations used in the numerical model. The predictions from the two-step reaction model are validated using experimental data from the WRCVC for deflagrative combustion tests. The predictions matched the experimental data well. The predicted pressure traces are compared with the experimentally measured pressures in the passages. The flame propagation along the passage is also evaluated with ion probes data and the predicted reaction zone.

When studying pressure-gain combustion and wave rotor combustors, it is vital that any experimental model accurately reflect the real world conditions/applications being studied; this not only confirms previous computational and analytical work, but also provides new insights into how these concepts and devices work in real life. However, mixture stratification can have a noticeable effect on multiple combustion properties, including flame propagation, pressure, ignition time delay, and more, and this is especially true in constant-volume combustion chambers. Because it is beneficial to model wave rotor systems using constant-volume combustors such as what is employed in the IUPUI Combustion and Propulsion Research Laboratory, these stratification effects much be taken into account and reduced if possible. This study sought to find an effective method to reduce stratification in a rectangular constant-volume combustion chamber by means of manual recirculation pump. Spark-ignited flames were first produced in the chamber itself and studied using schlieren and color videography techniques as well as quantitative pressure histories. After determining the pump's effectiveness in reducing stratification, it was next employed when a hot jet of combustion products from a separate combustion chamber was used as an ignition source instead of the spark plug - a process typically employed in real wave rotor combustors. Lastly, the pump was used to study the leakage from the system for future test cases in order to offer further recommendations on how to effectively use the recirculation system. This process found that key properties significant to wave rotor development, such as time ignition delay, were affected by these stratification effects in past studies that did not account for this detail. As such, the pump has been permanently incorporated into the wave rotor model, as stratification is a vital. Additionally, significant fuel leakage is possible during rotational pre-chamber cases, and this should be address before proceeding with such experiments in the future. To combat this, the pump system has been reduced in volume, and suggestions have been provided on how to better seal the main rectangular chamber in the future.

<p dir="ltr">This study contributes to research involving wave rotor combustors by studying the</p><p dir="ltr">development of a hot jet issuing from a cylindrical pre-combustion chamber. The pre-chamber was</p><p dir="ltr">developed to provide a hot fuel-air mixture as an ignition source to a rectangular combustion</p><p dir="ltr">chamber, which models the properties of a wave rotor channel. The pre-combustion chamber in</p><p dir="ltr">this study was rebuilt for study and placed in a new housing so that buoyancy effects could be</p><p dir="ltr">studied in tandem with other characteristics. The effectiveness of this hot jet is estimated by using</p><p dir="ltr">devices and instrumentation to measure properties inside the pre-chamber under many different</p><p dir="ltr">conditions. The properties tracked in this study include maximum pressure, the pressure and time</p><p dir="ltr">at which an aluminum diaphragm ruptures, and the moment a developed flame reaches a precise</p><p dir="ltr">location within the chamber. The pressure is tracked through use of a high-frequency pressure</p><p dir="ltr">transducer, the diaphragm rupture moment is captured with a high-speed video camera, and the</p><p dir="ltr">flame within the pre-chamber is detected by a custom-built ionization probe. The experimental</p><p dir="ltr">apparatus was used in three configurations to study any potential buoyancy effects and utilized</p><p dir="ltr">three different gaseous fuels, including a 50%-50% methane-hydrogen blend, pure methane, and</p><p dir="ltr">pure hydrogen. Additionally, the equivalence ratio within the pre-chamber was varied from values</p><p dir="ltr">of 0.9 to 1.2, and the initial pressure was set to either 1.0, 1.5, or 1.75 atm. In all cases, combustion</p><p dir="ltr">was initiated from a spark plug, causing a flame to develop until the diaphragm breaks, releasing</p><p dir="ltr">a hot jet of fuel and air from the nozzle inserted into the pre-chamber. In the pressure transducer</p><p dir="ltr">tests, it was found that hydrogen produced the highest pressures and fastest rupture times, and</p><p dir="ltr">methane produced the lowest pressures and slowest rupture times. The methane-hydrogen blend</p><p dir="ltr">provided a middle ground between the two pure fuels. An equivalence ratio of 1.1 consistently</p><p dir="ltr">provided the highest pressure values and fastest rupture out of all tested values. It was also found</p><p dir="ltr">that the orientation has a noticeable impact on both the pressure development and rupture moment</p><p dir="ltr">as higher maximum pressures were achieved when the chamber was laid flat in the “vertical jet”</p><p dir="ltr">orientation as compared to when it was stood upright in the “horizontal jet” orientation.</p><p dir="ltr">Additionally, increasing the initial pressure strongly increased the maximum developed pressure</p><p dir="ltr">but had minimal impact on the rupture moment. The tests done with the ion probe demonstrated</p><p dir="ltr">that an equivalence ratio of 1.1 produces a flame that reaches the ion probe faster than an</p><p dir="ltr">equivalence ratio of 1.0 for the methane-hydrogen blend. In its current form, the ion probe setup</p><p>18</p><p dir="ltr">has significant limitations and should continue to be developed for future studies. The properties</p><p dir="ltr">analyzed in this study deepen the understanding of the processes that occur within the pre-chamber</p><p dir="ltr">and aid in understanding the conditions that may exist in the hot jet produced by it as the nozzle</p><p dir="ltr">ruptures. The knowledge gained in the study can also be applied to develop models that can predict</p><p dir="ltr">other parameters that are difficult to physically measure.</p>