Wind energy is a relatively young but rapidly expanding industry. In order for wind generation to be cost effective, it must produce energy at a minimum cost per dollar of investment. Performance characteristics such as power output versus wind speed must be optimized in order to compete with other energy sources. Also, if the utility uses wind power for a part of its generation, the output power of these turbines must have the same high quality and reliability when it enters the utility grid. The ability to vary operating speed is important in wind generation because it allows for an optimization of the transfer of power from the wind to the turbine shaft. Doubly-fed induction generators (DFIG) are an interesting solution for variable-speed systems with limited variable speed range, and are typically used in wind energy conversion systems. / The objectives of this thesis are to implement a decoupled P-Q control of a DFIG that does not rely on mechanical sensors and to design a speed and position sensorless algorithm that is robust to variations of the values of the machine parameters. The sensorless DFIG control algorithm presented in this thesis is based on a modified phasedlock loop with an improved positioning algorithm. With the measured stator voltages, stator and rotor currents, the speed and position of the DFIG are estimated. The speed is estimated independent of machine parameters, which results in a significant improvement in speed control robustness to parameter variations. In addition, the algorithm avoids using differentiation, which significantly improves its immunity to noise and does not require the measurement of the rotor voltages. Also, it is shown that the positioning algorithm has an improved operation in generator mode. Although the accuracy of the positioning algorithm is depended on machine parameters; it is shown with the designed controller that the P-Q decoupled control is robust to changes of machine parameters. Theoretical and simulation results are validated on an experimental setup.

Wind generation has become one of the most popular choices of technology for adding new generation capacity to power systems worldwide. Several factors have contributed to the increased integration of wind generation, including environmental concerns and the continual increase in fossil fuel prices. As well, recent regulations have moved toward limitations on greenhouse gases, especially in the European Union (EU). Similar laws are currently under consideration in the US and other parts of the world. Other factors have also promoted the use of wind energy, such as advances in manufacturing and control technology and the attractiveness of wind as a “green” source of energy. The large-scale integration of wind power into an electricity system introduces planning and operational challenges because of the intermittent nature of wind speed and the difficulty involved in predicting it. For these reasons, wind energy is often considered an unreliable energy source. Additional problems are associated with the integration of large-scale wind farms into an electrical grid, among which wind power fluctuation is the most challenging. To maximize the penetration level of wind energy in a grid, a reliable technology must be developed in order to eliminate or at least decrease wind power fluctuation. The primary goal of this thesis was to develop methods of maximizing the penetration level of wind energy conversion systems (WECSs) into a grid, which requires mitigating wind power fluctuation. A robust control technique has therefore been developed for mitigating wind power fluctuation. This control technique exploits historical environmental data collected over a number of years in order to evaluate the profile of the output power of a variety of wind energy conversion systems (WECSs). The developed control technique was applied to Types A and C WECSs modifying the pitch angle controller of Type A WECS and the back-to-back converter control of Type C WECS. The Attachment of a storage device to the WECSs after the control technique is applied was investigated from both an economic and a technical point of view. The optimum sizing and siting of the wind energy conversion system equipped with the proposed control technique was also studied. This research is expected to contribute to the advancement of WECS technology by presenting a feasible solution to the problems associated with the integration of large-scale WECSs into electrical grids.

The increasing price of fuel and energy, combined with environmental laws and regulations, have led many different energy producers to integrate renewable, clean energy sources with non-renewable ones, forming the idea of energy hubs. Energy hubs are systems of technologies where different energy forms are conditioned and transformed. These energy hubs offer many advantages compared to traditional single-energy sources, including increased reliability and security of meeting energy demand, maximizing use of energy and materials resulting in increasing the overall system efficiency. In this thesis, we consider an energy hub consisting of natural gas (NG) turbines for the main source of energy— electricity and heat— combined with two renewable energy sources—wind turbines and PV solar cells. The hub designed capacity is meant to simulate and replace the coal-fired Nanticoke Generating Station with NG-fired power plant. The generating station is integrated with renewable energy sources, including wind and solar. The hub will also include water electrolysers for hydrogen production. The hydrogen serves as an energy storage vector that can be used in transportation applications, or the hydrogen can be mixed into the NG feed stream to the gas turbines to improve their emission profile. Alkaline electrolysers’ technology is fully mature to be applied in large industrial applications. Hydrogen, as an energy carrier, is becoming more and more important in industrial and transportation sectors, so a significant part of the thesis will focus on hydrogen production and cost. In order to achieve the goal of replacing the Nanticoke Coal-fired Power Plant by introducing the energy hub concept, the study investigates the modeling of the combined system of the different technologies used in terms of the total energy produced, cost per kWh, and emissions. This modeling is done using GAMS® in order to make use of the optimization routines in the software. The system is modeled so that a minimum cost of energy is achieved taking into account technical and thermodynamic constrains. Excess energy produced during off-peak demand by wind turbines and PV solar cells is used to feed the electrolyser to produce H2 and O2. Through this method, a significant reduction in energy cost and greenhouse gas (GHG) emissions are achieved, in addition to an increased overall efficiency.

Designing horizontal-axis wind turbine (HAWT) blades to achieve satisfactory levels of performance starts with knowledge of the aerodynamic forces acting on the blades. In this thesis, HAWT blade design is studied from the aspect of aerodynamic view and the basic principles of the aerodynamic behaviors of HAWTs are investigated. Blade-element momentum theory (BEM) known as also strip theory, which is the current mainstay of aerodynamic design and analysis of HAWT blades, is used for HAWT blade design in this thesis. Firstly, blade design procedure for an optimum rotor according to BEM theory is performed. Then designed blade shape is modified such that modified blade will be lightly loaded regarding the highly loaded of the designed blade and power prediction of modified blade is analyzed. When the designed blade shape is modified, it is seen that the power extracted from the wind is reduced about 10% and the length of modified blade is increased about 5% for the same required power. BLADESIGN which is a user-interface computer program for HAWT blade design is written. It gives blade geometry parameters (chord-length and twist distributions) and design conditions (design tip-speed ratio, design power coefficient and rotor diameter) for the following inputs / power required from a turbine, number of blades, design wind velocity and blade profile type (airfoil type). The program can be used by anyone who may not be intimately concerned with the concepts of blade design procedure and the results taken from the program can be used for further studies.

The debate on global warming is over (Stix, 2006 p24). The global community must now find ways to reduce greenhouse emissions, particularly from energy generation. Wind energy provides one of the potential solutions to generate renewable energy without creating harmful greenhouse gases. Wind energy is the fastest growing energy generation industry globally (‘Operating wind power capacity' 2006a). This rapid growth is being driven by increasing global energy demand, commitment from governments globally to international agreements including the Kyoto Protocol (UNFCCC 1997) to reduce the emission of greenhouse gases, as well as individual country commitments to mandatory renewable energy targets. Australia, whilst being a signatory to the United Nations Framework Convention on Climate Change (UNFCCC) commitment to reduce greenhouse gas emissions, has so far failed to ratify the Kyoto Protocol. In Australia, wind energy development to date has been driven primarily by the development of the Mandatory Renewable Energy Target (MRET) under the Renewable Energy (Electricity) Act 2000. This requires a commitment to 2% of total electricity generation (9,500GW) to be derived from renewable energy sources by the year 2010 (Warwryk, undated). It is now understood, that the current federal obligation to renewable energy is now oversubscribed, and consequently the likelihood of further wind energy projects being developed is highly limited (Brazzale 2005). External to the government commitment to renewable energy, the development of wind energy projects requires a range of inputs including, but not limited to; an understanding of the wind resource, security of land, access to suitable electricity transmission grid, a market for the electricity, access to suitable technology and a level of community support. Whilst the literature related to project management and risk management is extensive, the literature related to the risks associated with wind energy development in Australia is limited. This research then seeks to fill a void that asks the question; How can project managers minimise the risk associated with wind energy developments in Australia? To investigate this research problem, comparative case study analysis was adopted as a methodology utilising a structured interview process of project managers responsible for the development of 8 Australian wind energy projects. This research shows that the greatest risk to Australian projects is the lack of security associated with the current federal legislation and the consequent loss of market value of the power from wind energy projects. A number of additional primary and secondary risks are identified by the interview participants, and the research is able to draw out three common themes of risk management strategies. These three themes were categorised as conservatism, due diligence and proactivism. This study contributes to the research associated with project management, risk management and wind energy development. This insight into the Australian wind energy industry provides policy makers, educators and stakeholders with information to assist in improving the political, economic and social environment for further wind energy development, in order to mitigate against further greenhouse gas emission and combat global warming.

The debate on global warming is over (Stix, 2006 p24). The global community must now find ways to reduce greenhouse emissions, particularly from energy generation. Wind energy provides one of the potential solutions to generate renewable energy without creating harmful greenhouse gases. Wind energy is the fastest growing energy generation industry globally (‘Operating wind power capacity' 2006a). This rapid growth is being driven by increasing global energy demand, commitment from governments globally to international agreements including the Kyoto Protocol (UNFCCC 1997) to reduce the emission of greenhouse gases, as well as individual country commitments to mandatory renewable energy targets. Australia, whilst being a signatory to the United Nations Framework Convention on Climate Change (UNFCCC) commitment to reduce greenhouse gas emissions, has so far failed to ratify the Kyoto Protocol. In Australia, wind energy development to date has been driven primarily by the development of the Mandatory Renewable Energy Target (MRET) under the Renewable Energy (Electricity) Act 2000. This requires a commitment to 2% of total electricity generation (9,500GW) to be derived from renewable energy sources by the year 2010 (Warwryk, undated). It is now understood, that the current federal obligation to renewable energy is now oversubscribed, and consequently the likelihood of further wind energy projects being developed is highly limited (Brazzale 2005). External to the government commitment to renewable energy, the development of wind energy projects requires a range of inputs including, but not limited to; an understanding of the wind resource, security of land, access to suitable electricity transmission grid, a market for the electricity, access to suitable technology and a level of community support. Whilst the literature related to project management and risk management is extensive, the literature related to the risks associated with wind energy development in Australia is limited. This research then seeks to fill a void that asks the question; How can project managers minimise the risk associated with wind energy developments in Australia? To investigate this research problem, comparative case study analysis was adopted as a methodology utilising a structured interview process of project managers responsible for the development of 8 Australian wind energy projects. This research shows that the greatest risk to Australian projects is the lack of security associated with the current federal legislation and the consequent loss of market value of the power from wind energy projects. A number of additional primary and secondary risks are identified by the interview participants, and the research is able to draw out three common themes of risk management strategies. These three themes were categorised as conservatism, due diligence and proactivism. This study contributes to the research associated with project management, risk management and wind energy development. This insight into the Australian wind energy industry provides policy makers, educators and stakeholders with information to assist in improving the political, economic and social environment for further wind energy development, in order to mitigate against further greenhouse gas emission and combat global warming.

Thesis (M.S.)--Missouri University of Science and Technology, 2008. / Vita. The entire thesis text is included in file. Title from title screen of thesis/dissertation PDF file (viewed May 12, 2008) Includes bibliographical references (p. 64-66).

Thesis (MS)--Montana State University--Bozeman, 2009. / Typescript. Chairperson, Graduate Committee: Douglas S. Cairns. Includes bibliographical references (leaves 138-143).

Thesis (M.S.)--University of Wisconsin--Madison, 1996. / Typescript. eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references (leaves 143-162).

Thesis (Ph. D.)--Ohio State University, 2006. / Title from first page of PDF file. Includes bibliographical references (p. 140-147).