In 1996, the promulgation of the amended Telecommunications Act initiated a series of liberalization in telecommunication industry. From 1998 to 2000, Taiwan had become the most rapid growth area around the world with 130% compound annual growth rate and had marked a milestone with more than 80% of penetration by the end of 2000. This study focuses on the pricing plans offered by the main operators, CHT, TCC and FET, to analyze the pricing strategies and the competition scenarios with one another. In this study, we, first, gather the pricing plans of the operators and then review the history of the price adjustment. At last, we compare the pricing plans across the boundary of the operators. From the history of the price adjustment and the market evolution, we realize that the new subscribers encouraged by low prices are mostly low in airtime usages. The operators discriminates these low airtime users more in prices under the consideration of market competition and profit gaining. From reviewing the pricing plans of the operators respectively, we find the existence of ¡§redundant¡¨ pricing plans, which might bring the operators extra income. From comparison of the pricing plans offered by the three main operators, we conclude the three players try to lower the competition strength by charging high in different segments.

In this thesis, we take an application of multiple symbol differential detection (MSDD) technique in direct-sequence code division multiple access (CDMA) system. It is well- known that MSDD is an effective noncoherent demodulator which outperform the conventional M-ary differential phase shift keying (MDPSK) in additive white Gaussian noise (AWGN) channel. Take MPSK demodulator into consideration, the performance of MSDD based on noncoherent demodulation approaches the performance of coherent demodulation. However, there is little research about MSDD in frequency-selective fading channel. We are now combining the MSDD and Rake receiver to be the signal demodulator. In conventional, there are two kinds of Rake receivers. One is coherent demodulator. Another is noncoherent demodulator. For coherent demodulation, it needs to have channel estimation at each path. The advantage is that the performance will be improved. On the other hand, the disadvantage is complexity and operation will increase. On the contrast, for noncoherent demodulation, it is the performance degradation and complexity simplification. In this thesis, We suggest a multiple symbol differential detection on Rake receiver for CDMA system. From our computer simulation, only for hard decision, the performance is improved and the improvement is proportional to the number of multipath and the number of the length of multiple symbol. This will not happen in conventional MDPSK. However, from our observation, the improvement of performance is degrading as the number of multipath increase. Thus, we employee the technique of Viterbi decoding differential detection (VDDD) to demodulate the differential sequence. By the property of decision interval, the VDDD can obtain additional improvement.

A novel CMOS tunable bandpass filter and a novel voltage controlled oscillator are proposed. Both circuits are designed using the UMC 0.5£gm CMOS process parameters. The CMOS tunablebandpass filter is realised by using the intrinic parasitic capacitance of the MOS transistor. This filter has neither on-chip planar inductor nor poly-capacitance; therefore, the chip area is reduced. Simulation results show that the bandpass filter is tunable in the range between 190MHz and 347MHz. Therefore, the filter is suitable for the IF filter application that is between 200MHz and 300MHz. The Q-factor is also tunable and has a maximum value of 983. Applying the circuit of the bandpass filter, a second order voltage controlled oscillator is designed. Simulation results show that the voltage controllable oscillator is tunable in the range between 444MHz and 746MHz.

This thesis proposes a knowledge management technique, called knowledge map management system, which consists of three components: knowledge navigation, knowledge seeking, and learning history advisory. The knowledge navigation function helps knowledge seekers to understand the knowledge structure. Similarly, the knowledge-seeking component helps knowledge seekers to retrieve knowledge with its structure. The learning adviser generalizes the knowledge access pattern in problem solving history and advises knowledge in the problem solving process. In this study, we prototype the knowledge map management system to facilitate knowledge sharing activities. In order to keep the knowledge map up to date, we also propose the incremental approach to maintaining knowledge structure with the addition of knowledge artifacts. The knowledge map creation and maintenance functions are evaluated using documents collected from SCTNet and master thesis repository at National Central Library, and result in encouraging results.

The purpose of this study is to investigate the efficiencies of bioremediation of sandy beach contaminated by crude oil. In this study, we used two lab-scale tanks, tank-A and tank-B, to simulate a sandy beach contaminated by crude oil. In the experiments, we added the bioreagents and oleophilic fertilizers (Inipol EAP 22®) in order to enrich crude oil degradation of sandy beach. The crude oil was degraded by nature culture in tank-A, while the crude oil was degraded by the mixed culture of several pure strains¡]MO-1, KS-1, DS-4, PF-4, PH-2, B-1, TF and XY-2¡^. We divided the experiment into five stages in this study. In conclusion, we found that the oleophilic fertilizers could increase both of the growth rate of oil degradation bacteria and crude oil biodegradation rate. However, a part of the fertilizers might flow into the ocean due to idal current. The addition of mixed culture could help to improve the biodegradation rate of sandy beach contaminated by crude oil.

Digital satellite communication systems are equipped with nonlinear amplifiers such as travelling wave tube (TWT) amplifiers at or near saturation for better efficiency. The TWT exhibits nonlinear distortion in both amplitude and phase (AM/AM and AM/PM) conversion, respectively. That is, in the digital satellite communication the transmission is disturbed not only by the non-linearity of transmitter amplifier, but also by the inter-symbol interference (ISI) with additive white Gaussian noise. To compensate the non-linearity of the transmitter amplifier and ISI, in this thesis, a new nonlinear compensation scheme consists of the predistorter and adaptive third-order Volterra-based equalizer, with the inverse QRD-RLS (IQRD-RLS) algorithm, which are located before and after the nonlinear channel, is proposed respectively. The third-order Volterra filter (TVF) equalizer based on the IQRD-RLS algorithm achieve superior performance, in terms of convergence rate, steady-state mean-squared error (MSE), and numerically stable. They are highly amenable to parallel implementation using array architectures, such as systolic arrays. The computer simulation results using the M-ary PSK modulation scheme are carried out the signal¡¦s constellation diagrams, the learning curve of the MSE and the bit error rate (BER) are compared with conventional least mean square (LMS), gradient adaptive lattice (GAL) and adaptive LMS with lattice pre-filter algorithms.

Growth Mechanism and Infrared Detection of High-temperature Superconducting and Colossal Magnetoresistance Films Department of Electrical Engineering, National Sun Yat-Sen University Meng-Tsong Hong* Ying-Chung Chen**, Hsiung Chou** -------------------------------------------------- Abstract---- The growth mechanism of YBa2Cu3O7-d (YBCO) films grown by RF sputtering has been investigated. When growing films by RF sputtering, the shape of the plasma and the degree of resputtering effect were varied by setting different relative positions of the heater to the gun. As the substrate was near the plasma, the negative oxygen ions resputtered part of the mobile atoms from the surface of film back into the plasma, which caused the composition distortion, delayed the merge of grains and left uncovered holes. Setting a longer relative distance, the resputtering effect was suppressed and the precipitates appeared on the surface of films resulting in a rough surface. At an optimum relative position between heater and gun, the function of resputtering produced a polishing effect on the surface of films. This polishing effect suppressed the growth of precipitates without slowing down the growth of grains, a smooth and precipitate-free YBCO film might obtain. We also found that the film with smooth and precipitate-free morphology exhibited suppressed superconductivity. The most direct way to enhance the photoresponse of a bolometer is by modifying the microbridge from a single straight bridge to a meander or change the thermal coupling configuration between bolometer and heat sink. In the study of high-temperature superconducting (HTSC) bolometers, it is found that the geometry and thermal coupling configuration play very important roles on the behavior of heat conduction, which alter the thermal conversion efficiency, DT/WD. Actually, DT/WD is a matter of the absorption of the AC thermal irradiation and the dissipation of both the irradiation and the DC joule heat generated by the bias current. The competition between the capability of heat dissipation and the thermal generation determined the magnitude of DT/WD. The La0.67Ca0.33MnO3-y (LCMO) thin films with epitaxial structure and smooth surface morphology have been deposited. A LCMO thin-film microbridge was fabricated into a microbridge by conventional photolithography and dry etching for optical detection. The measured photoresponse, DV, of this LCMO thin-film microbridge reveals that it is bolometric in nature. The photoresponse is linearly proportional to the bias current Ib and the power density of irradiation WD, which strongly suggests the applicability of an LCMO thin-film microbridge to a linear optical detector. The ratio of the photoresponse to the irradiated power density, DV/WD, is independent of the incident-light wavelength l from 0.633 to 3.5 mm. The dependence of the photoresponse on modulated frequency f, follows the DV µ f -0.21 relation. Under Ib = 100 mA and f = 5 Hz at an operating temperature Top = 223 K, the responsivity S and noise voltage Vn are 685 V/W and 20 nV¡ÑHz -0.5, respectively, for this LCMO thin-film microbridge. From the measured S and Vn, the noise equivalent power (NEP) and detectivity D* were be calculated to be 2.92´10-11 W¡ÑHz -0.5 and 2.76´109 cm¡ÑHz 0.5¡ÑW -1, respectively, for this LCMO thin-film microbridge. The experimental results from this LCMO thin-film microbridge show the practical applicability of this new detector system compared to other established detectors. *Student **Advisor

In recent years, many people use the World Wide Web and Internet to find information that they want. HTML is a document markup language for publishing hypertext on the WWW. HTML has been the target format for content developers around the world. Basically, HTML tags serve the primary purpose of describing how to display a data item. Therefore, HTML documents are difficult to find some useful information. That is because, HTML documents are mixed content with display tags. On the other hand, XML is the another data format for data exchange inter-enterprise applications on the Internet. In order to facilitate data exchange, industry groups define public Document Type Definitions (DTD) that specify the format of the XML documents to be exchanged between their applications. Moreover, WWW/EDI or Electric Commerce is very popular and a lot of business data uses XML to exchange on the World Wide Web. Basically, XML tags describe the data itself. The contents (meaning) of the XML documents and the display format is separated. It could be easily to find meaningful information of the XML documents and analyze the information. Moreover, when a large volume of business data (XML documents) exists, we must transform the XML documents to the relational databases. In order to exchange business data between applications, we must construct the XML documents from the relational database. In this thesis, we design the mapping technique and present the implementation of mapping tools between XML documents and relational databases. XML document is fundamentally different from relational data. XML document are hierarchy, and elements of document should be nested and repeated more times (i.e., set-valued and recursion). Therefore, we can not map from the XML documents to the relational databases straightforwardly. Our mapping technique must resolve the above problems. We design and implement a mapping technique between the XML documents and the relational database such that those mapping can be done automatically for any kind of XML documents and any kind of commercial relational databases. The whole tools are implemented in Visual Basic and SQL Server 2000. From our experiences, we show that our efficient mapping technique can be applied to any kind of relational databases without any extra requirements or changes to the databases.

In periodic wireless broadcasting, air behaves like a storage medium requiring new data organization and access methods.Due to power limit for the portable units (ex. the palmtop), how to design an energy-saving organization is a key issue.Imielinski et al. have proposed the hashing based schemes, including the Hashing A and Hashing B schemes, to save energy in the progress of getting data of interest. The Hashing B scheme improves the directory miss phenomenon in the Hashing A scheme, where the directory miss is that the client's initial probe comes before the bucket containing his key but after the bucket which contains a proper offset. However, based on these two schemes, if the differences between the minimum overflow and the other overflows are large extremely or the small overflows appear near the rear part of the broadcast file, both schemes have a poor performance. Therefore, in this thesis, we propose four multiple-hashing-functions-based schemes, including the FirstR, FirstL, AvgK and TopK schemes, to overcome such the situations. The basic idea is to use cutlines to divide the broadcast file with N logical buckets into several regions, and then each region may have the different minimum overflow. Since the minimum overflow in each region can be different, we can have different hashing functions for those regions to determine the positions of the designated buckets. Among the proposed schemes, the difference is how to determine the positions of the cutlines. The FirstR scheme finds those cutlines from the right end to the left whenever the difference of overflows of two adjacent logical buckets is greater than or equal to 1. The FirstL scheme finds those cutlines from the left end to the right whenever the difference of overflows of two adjacent logical buckets is greater than or equal to 1. In the AvgK scheme, we first calculate AvgD, the average of the differences of two consecutive overflows whose values are large than or equal to 1. Then we find cutlines from the left end to the right whenever the difference of two adjacent logical buckets is greater than or equal to AvgD. The TopK determines the cutlines by considering the descending order of the differences of overflows. From our performance analysis and simulation study, the performance of the TopK scheme is the best among the proposed schemes. Therefore, we then make a comparison between the TopK scheme and the Hashing B scheme. Since the number of the hashing functions in the TopK scheme is larger than those in the Hashing B, the physical bucket in the TopK scheme is somewhat bigger than that in the m Hashing B scheme. In our simulation, we have considered this factor as well. From our performance analysis and simulation study, we show that the performance of the TopK scheme performs better than that of the Hashing B scheme, even though the above factor about the storage size is considered. The TopK scheme improves the directory miss in the Hashing B scheme; therefore, the average access time is improved excellently.

A symbolic image database system is a system in which a large amount of image data and their related information are represented by both symbolic images and physical images. How to perceive spatial relationships among the components in a symbolic image is an important criterion to find a match between the symbolic image of the scene object and the one being store as a modal in the symbolic image database. Spatial reasoning techniques have been applied to pictorial database, in particular those using 2D strings as an index representation have been successful. In this thesis, we extend the existing three levels of type-i similarity to more levels to aid similarity retrieval more precisely. There are 13 spatial operators which were introduced by Lee and Hsu to completely represent spatial relationships in 1D space. But, they just combined the 13 spatial relationships on x- and y-axis to represent the spatial relationships in 2D space by 13 times 13 = 169 spatial relationships. However, the 169 spatial relationships are still not sufficient to show all kinds of spatial relationships between any two objects in 2D space. For example, the directional relationships, like North or South West, exist in 2D space and is difficult to be deducted from those 13 spatial operators. Thus, we add the nine directional relationships to the 169 spatial relationships in 2D space. In this way, we can distinguish up to 289 spatial relationships in 2D space. Moreover, in our proposed strategy, we also take care of the problem caused by the MBRs. In most of the previous approaches for iconic indexing, for simplifying the concerns, they apply the MBRs of two objects to define the spatial relationship between them. The topological relationships, however, between objects can be quite different from the spatial relationship of their respective $MBR$s. Therefore, sometimes, it is hard to correctly describe the spatial relationship of the objects in terms of the relationships between their corresponding MBRs. To improve this drawback resulted from MBRs, we adopting the concept of topological relationships in our proposed strategy. Good access methods for large image databases are important for efficient retrieval. The signature files can be viewed as a preselection searching filter to prune off the unsatisfied images. In order to solve the ambiguity of the MBRs and to present the spatial relationships in two dimensional space completely, we propose a hybrid approach-based signature extraction method for similarity retrieval. From our simulation study, we show that our approach can provide a higher rate of a correct match and requires a smaller storage cost than Lee et al.'s 2D B-based signature approach. In some case, the correct match rate based on our proposed strategy can be up to 42.18%, while it is just 16.66% in Lee et al.'s strategy. Moreover, the worst case of the storage cost required in our proposed strategy is 1686 bits. But, it always needs 2015 bits in Lee et al.'s strategy.