No description available.

No description available.

Autoignition and oxidation of two Methane (CH4) and Dimethyl Ether (CH3OCH3 or DME) mixtures in air were studied in shock tubes over a wide range of equivalence ratios at elevated temperatures and pressures. These experiments were conducted in the reflected shock region with pressures ranging from 0.8 to 35.7 atmospheres, temperatures ranging from 913 to 1650 K, and equivalence ratios of 2.0, 1.0, 0.5, and 0.3. Ignition delay times were obtained from shock-tube endwall pressure traces for fuel mixtures of CH4/CH3OCH3 in ratios of 80/20 percent volume and 60/40 percent volume, respectively. Close examination of the data revealed that energy release from the mixture is occurring in the time between the arrival of the incident shock wave and the ignition event. An adjustment scheme for temperature and pressure was devised to account for this energy release and its effect on the ignition of the mixture. Two separate ignition delay correlations were developed for these pressure- and temperature-adjusted data. These correlations estimate ignition delay from known temperature, pressure, and species mole fractions of methane, dimethyl ether, and air (0.21 O2 + 0.79 N2). The first correlation was developed for ignition delay occurring at temperatures greater than or equal to 1175 K and pressures ranging from 0.8 to 35.3 atm. The second correlation was developed for ignition delay occurring at temperatures less than or equal to 1175 K and pressures ranging from 18.5 to 40.0 atm. Overall good agreement was found to exist between the two correlations and the data of these experiments. Findings of these experiments also include that with pressures at or below ten atm, increased concentrations of dimethyl ether will consistently produce faster ignition times. At pressures greater than ten atmospheres it is possible for fuel rich mixtures with lower concentrations of dimethyl ether to give the fastest ignition times. This work represents the most thorough shock tube investigation for oxidation of methane with high concentration levels of dimethyl ether at gas turbine engine relevant temperatures and pressures. The findings of this study should serve as a validation for detailed chemical kinetics mechanisms.

No description available.

No description available.

Degradable low-fouling hydrogels are ideal vehicles for drug and cell delivery. For each application, hydrogel degradation rate must be re-optimized for maximum therapeutic benefit. We developed a method to rapidly tune degradation rates of low-fouling poly(oligo(ethylene glycol) methyl ether methacrylate) (P(EG)xMA) hydrogels by modifying two interdependent variables: (1) base-catalyzed crosslink degradation kinetics, dependent on crosslinker electronics (electron withdrawing groups (EWGs)); and (2) polymer hydration, dependent on the molecular weight (MW) of poly(ethylene glycol) (PEG) pendant groups. By controlling EWG strength and PEG pendant group MW, P(EG)xMA hydrogels were tuned to degrade over 6 to 52 d. A six-member P(EG)xMA copolymer library yielded slow and fast degrading low-fouling hydrogels for short- and long-term delivery applications. The degradation mechanism was also applied to RGD-functionalized poly(carboxybetaine methacrylamide) (PCBMAA) hydrogels to achieve slow (52 d) and fast (13 d) degrading low-fouling, bioactive hydrogels. / Thesis / Master of Science (MSc) / The delivery of drugs and cells to disease sites is hindered by transport barriers, which can be overcome through local delivery. Injectable hydrogels can serve as local depots that release drugs or cells to improve therapeutic benefit. Currently, however, hydrogels suffer from uncontrolled degradation in the body, degrading at unpredictable rates dependent on the local environment; hydrogels with predictable and tunable degradation rates are therefore required. Herein, we report a method to produce a library of polymers that in situ crosslink to form hydrogels with a range of degradation rates only influenced by the local environments pH, a known quantity. Moreover, the polymers are low-fouling and therefore have minimal non-specific interactions with biomolecules and cells, which improves biocompatibility.

Hydrophilic/hydrophobic block copolymers as proton exchange membranes (PEMs) has become an emerging area of research in recent years. Three series of hydrophilic/hydrophobic, fluorinated/sulfonated multiblock copolymers were synthesized and characterized in this thesis. These copolymers were obtained through moderate temperature (~100°C) coupling reactions, which minimize the ether-ether interchanges between hydrophobic and hydrophilic telechelic oligomers via a nucleophilic aromatic substitution mechanism. The hydrophilic blocks were based on the nucleophilic step polymerization of 3,3′-disulfonated, 4,4′-dichlorodiphenyl sulfone with an excess 4,4′-biphenol to afford phenoxide endgroups. The hydrophobic (fluorinated) blocks were largely based on decafluoro biphenyl (excess) and various bisphenols. The copolymers were obtained in high molecular weights and were solvent cast into tough membranes, which had nanophase separated hydrophilic and hydrophobic regions. The performance and structure-property relationships of these materials were studied and compared to random copolymer systems. NMR results supported that the multiblock sequence had been achieved. They displayed superior proton conductivity, due to the ionic proton conducting channels formed through the self-assembly of the sulfonated blocks. The nano-phase separated morphologies of the copolymer membranes were studied and confirmed by atomic force microscopy. Through control of a variety of parameters, including ion exchange capacity and sequence lengths, performances as high, or even higher than those of the state-of-the-art PEM, Nafion, were achieved. / Ph. D.

Phosphorus-containing high performance polymers have been extensively studied during the last 10 years. These materials are of interest for a variety of optical and fire resistant properties, as well as for their ability to complex with the inorganic salts. This dissertation has focused on the nature of the phosphonyl group interactions with hydroxyl containing polymers, such as the poly(hydroxy ether)s. These may be considered linear models of epoxy resins and are also closely related to dimethacrylate (vinyl ester) matrix resins that are important for composite systems. It has been shown that bisphenol A poly(arylene ether phosphine oxide/sulfone) homo- or statistical copolymers are miscible with a bisphenol A-epichlorohydrin based poly(hydroxy ethers) (PHE), as shown by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC), infrared spectroscopy and , solid state cross polarization-magic angle spinning nuclear magnetic resonance (CP-MAS). These measurements illustrate the strong hydrogen bonding between the phosphonyl groups of the copolymers and the pendent hydroxyl groups of the PHE as the miscibility inducing mechanism. Complete miscibility at all blend compositions was achieved with as little as 20 mole% of phosphine oxide units in the poly(arylene ether) copolymer. Replacement of the bisphenol A moiety by other diphenols, such as hydroquinone, hexafluorobisphenol A and biphenol did not significantly affect blend miscibilities. Miscible polymer blends with PHE were also made by blending poly(arylene thioether phosphine oxide), and fully cyclized phosphine oxide containing polyimides based on (prepared from 2,2'-bis[4-(3,4-dicarboxyphenoxy)phenyl]propane dianhydride (BPADA) and bis(m-aminophenyl) methyl phosphine oxide (DAMPO)) or bis(m-aminophenyl) phenyl phosphine oxide). Additional research has focused on the influence of these materials on the property characteristics of vinyl ester matrix resins and has shown that the concentration of phosphonyl groups controls the homogeneity of both oligomers and the resulting networks. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and fracture toughness measurements further confirmed the qualitative observations. Metal salts, such as CoCl2 and CuCl2 had earlier been demonstrated to form complexes/nanocomposites with phosphorus-containing poly(arylene ethers). It has been possible to prepare transparent films with 100 mol% of metal chlorides, based upon the phosphonyl groups. The films are transparent, unlike the opaque polysulfone control systems. FTIR results suggested the formation of inorganic salt and polymer complexes at low concentrations. TEM showed homogeneous morphology at low concentrations and excellent dispersion even at high mole % of salts. Cobalt materials reinforce the basic poly(arylene ether)s to provide higher modulus values and influence positively the char yield generated after TGA experiments in air. The cobalt salt/BPADA-DAMPO polyimide composites also yield transparent films, implying very small dimensions. Silica-polymer nanocomposites were also produced by mixing commercial silica colloid/N,N-dimethylacetamide (DMAc) fine dispersions (~ 12 nm) with bisphenol A poly(arylene ether phenyl phosphine oxide). The dry films produced by solution casting are transparent and silica colloids are evenly dispersed (~ 12 nm) into the polymer matrix as shown by TEM. These nanocomposites increased char yield compared with the polymer control, suggesting their fire retardant character. In comparison, the silica/polysulfone hybrid films prepared by the same methods were opaque and the char yield was not improved. This different phase behavior has been explained to be due to the hydrogen bonding between phosphonyl groups and silanol hydroxyl groups on the surface of the nanosilica. / Ph. D.

The objectives of this research were to study the gas transport properties of proton exchange membranes (PEM), namely disulfonated poly(arylene ether sulfone) (BPSH-35), post sulfonated diels-alder poly(phenylene) (SDAPP), and poly(perfluoro sulfonic acid) (Nafion). The O2 gas permeabilities were found to be lower in BPSH and SDAPP as compared to poly(perfluoro sulfonic acid) because of difference in Tg (TgBSPH= 250 oC, TgSDAPP= 330 oC versus TgNafion=150 oC). Higher Tg polymers have a more rigid, inflexible polymer segments causing a reduction in gas permeability. In comparison to SDAPP, BPSH has a lower O2 gas permeability because of the bulky side groups in the SDAPP backbone. O2 sorption measurements were carried out both under non-humidified and humidified conditions as a function of relative humidity and temperature at a normal PEM operating pressure of 1 atm. Under non-humidified conditions, BPSH, SDAPP, and Nafion 112 exhibited Henry's Law sorption, consistent with dilute dissolution of O2 into the polymer matrix. The enthalpies of sorption were calculated to determine the interaction of O2 with each membrane. The sorption enthalpies in BPSH and SDAPP increased with increasing pressure indicating the formation of more O2-O2 interactions. The enthalpies in Nafion 112 were relatively constant with increasing pressure. In the presence of moisture, the sorption behavior changed from Henry's Law to Type IV sorption behavior, which is common in hydrophilic polymers. The SDAPP membrane was found to have the highest percent wet O2 mass uptake because of a higher number of sulfonic acid groups interacting with the water/O2 system. Finally the O2 sorption for various porous catalyst powders, consisting of platinum supported on carbon was measured in the non-humidified and humidified state. The catalysts were found to have Knudsen diffusion in the non-humidified state with 20 wt% Pt-C having the largest O2 sorption. In the humidified state, the highest O2 mass uptake was achieved with 40 wt% Pt-C. These results are explained in terms of the trade-off between catalyst dispersion and catalyst size. Furthermore, O2 sorption measurements were utilized for membrane electrode assemblies containing 40 wt% Pt-C and hot pressed at 210 oC for BPSH-35 (25 and 80K) and Nafion 112 membranes. The same sorption behavior occurred in the MEAs as in the neat membrane, but at a lower capacity. This is because the electrode introduces a more tortuous path to the gas molecules permeating across the membrane. / Ph. D.

Poly(arylene ether sulfone)s (PAES) are important commercial polymers and have been extensively studied due to their excellent thermal and mechanical properties. However, some applications are still limited when good solvent resistance and low thermal expansion coefficient are required. There has been a continuous interest in developing new PAES based on new monomers or polymer modifications to obtain new properties or to enhance existing properties. In this dissertation, the synthesis, characterization and structure-property relationship of new 1,4-cyclohexylene ring containing PAESs were comprehensively studied. Different polymerization techniques were used to synthesize polymers with different segmental lengths. The monomer, 4,4'-[trans-1,4-cyclohexanebis(methylene)] bisphenol (CMB), was synthesized and fully characterized. Based on 4,4′-dihydroxy-p-terphenyl (DHTP), 4,4′-dihydroxybiphenyl (DHBP) and the CMB monomer, homopolymer and random copolymers of PAES were prepared with high molecular weights and high glass transition temperatures. Dynamic mechanical analysis (DMA) on these polymers showed multiple sub-Tg relaxations. A large increase in the ultimate elongation was obtained with the CMB and DHTP containing sample, which could be due to the strong sub-Tg relaxations observed from the DMA results. A series of four acid chloride monomers were synthesized and polymerized with phenol terminated PAES oligomers. Solution polymerization and pseudo-interfacial polymerization techniques were used to prepare both bisphenol-A (bis-A) based and DHBP based PAES oligomers. With the incorporation of the trans-1,4-cyclohexylene units, decreases in the glass transition temperatures were observed from both the bis-A based and the DHBP based polymers. However, melting transitions were only observed in the DHBP based trans-1,4-cyclohexylene containing PAESs. Crystallinity was confirmed by differential scanning calorimetry (DSC) and wide angle X-ray diffraction (WAXD). A mechanical property study of the high molecular weight trans-1,4-cyclohexylene containing polymer samples showed moderate ultimate elongation enhancements. A series of PAES-polyester multiblock copolymers were synthesized with both solution method and melt polymerization. In the solution method, phenol terminated PAES oligomers and the acid chloride terminated poly(1,4-cyclohexylenedimethylene terephthalate) (PCT) oligomers were presynthesized and coupled in solution. The molecular weights of the polymer products obtained from the solution method were limited by solubility issues. Melt phase polymerization was employed to obtain high molecular weight polymers. Hydroxy ethoxy terminated PAES oligomers were synthesized and polymerized with 1,4-cyclohexanedimethanol (CHDM) and dimethyl terephthalate (DMT) in the melt. Polymers with high molecular weights were obtained. Tensile test results suggested that the mechanical properties of these polymers were dominated by the PAES components with polyester contents up to 20 wt%. Melting transitions were observed from polymers with higher polyester contents, and these polymers exhibited limited solubility in common organic solvents. / Ph. D.