No description available.

<p>The thesis is dealing with mixing processes havingapplication to ground improvement by deep mixing. The mainobjectives of the thesis is to make a contribution to knowledgeof the basic mechanisms in mixing binding agents into soil andimprove the knowledge concerning factors that influence theuniformity of stabilised soil.</p><p>A great part of the work consists of a literature surveywith particular emphasis on literature on the processindustries. This review forms a basis for a profounddescription and discussion of the mixing process and factorsaffecting the process in connection with deep mixingmethods.</p><p>The thesis presents a method for a simple field test for thestudy of influential factors in the mixing process. A number offactors in the installation process of lime-cement columns havebeen studied in two field tests using statistical multifactorexperiment design. The effects of retrieval rate, number ofmixing blades, rotation speed, air pressure in the storagetank, and diameter of the binder outlet on the stabilisationeffect and the coefficient of variation determined byhand-operated penetrometer tests for excavated lime-cementcolumns, were studied.</p><p>The literature review, the description of the mixingprocess, and the results from the field tests provide a morebalanced picture of the mixing process and are expected to beuseful in connection to ground improvement projects and thedevelopment of mixing equipments.</p><p>The concept of sufficient mixture quality, i.e. theinteraction between the mixing process and the mechanicalsystem, is discussed in the last section. By means ofgeostatistical methods, the analysis considers thevolume-variability relationship with reference to strengthproperties. According to the analysis, the design values forstrength properties depends on the mechanical system, the scaleof scrutiny, the spatial correlation structure, and the conceptof safety, i.e. the concept of sufficient mixture quality isproblem specific.</p><p><b>Key words:</b>Deep Mixing, Lime cement columns, Mixingmechanisms, Mixture quality, Field test, ANOVA, Variancereduction.</p>

Opening-mode fracture shapes are typically the result of brittle deformation and proportional growth in fracture height, length, and width. Based on the typical fracture shape, it is assumed that fracture tips are free to propagate in all directions. Some natural rock fractures have been shown to form as a result of slow non-elastic deformation processes. Such fractures may propagate to a finite length or height and accommodate further growth by aperture widening only. To determine the growth conditions of a fracture in the Triassic-Jurassic La Boca Formation of northeastern Mexico and to test fracture growth models, I combined fluid inclusion microthermometry and SEM-based cathodoluminescence cement texture analysis to determine the relative timing of fracture cement precipitation and related fracture opening for five samples collected along its trace. Fracture growth initiated at a minimum age of 70 Ma as two separate fractures with branching fracture tips that coalesced to a single continuous fracture under prograde burial conditions at a minimum age of 54 Ma. At this stage, fracture growth was accommodated by both propagation (i.e. increase in trace length) and by an increase in aperture during maximum burial and early exhumation. Samples collected at the fracture tips recorded temperatures reflecting fracture opening starting with maximum burial at a minimum age of 48 Ma at one tip and of 38 Ma at the other tip. Synkinematic fluid inclusions in crack-seal cement track continued fracture opening close to the fracture tips without a concurrent increase in trace length after 38 Ma until about 21 Ma. I attribute the observed change in fracture growth mechanism to a change in material response. The stage in aperture increase without propagation corresponds to an increase in elastic compliance or in non-elastic flow properties. Non-elastic flow can be attributed to solution-precipitation creep of the host rock. Dissolution of host quartz grains and subsequent quartz precipitation is consistent with the abundance of quartz fracture cement formed during exhumation. Cement textures from fractures in the La Boca Formation mimic those found in subsurface core, which allows application of the results to a variety of geologic environments. / text

M. Tech. Engineering: Civil. / Aims investigate the response of cement stabilised sub-base layers to dynamic load by evaluating the changes in stiffness at known strain level, and to compare the stiffness from dynamic loads with those derived from the Unconfined Compressive Stress (UCS) test.

Αντικείμενο της παρούσας Μεταπτυχιακής Διπλωματικής Εργασίας είναι η διερεύνηση της τιμής του συντελεστή διαπερατότητας άμμων διαφορετικής κοκκομετρικής σύνθεσης, η αξιολόγηση των αποτελεσμάτων και η σύγκριση τους με τιμές που προκύπτουν εφαρμόζοντας γνωστές εξισώσεις πρόβλεψης της τιμής του συντελεστή διαπερατότητας και, τέλος, η ειδική εφαρμογή των αποτελεσμάτων σε μια προσπάθεια διαμόρφωσης μοντέλου πρόβλεψης της ενεσιμότητας αιωρημάτων τσιμέντου σε άμμους. / Purpose of the Thesis is to investigate the value of the coefficient of sands permeability, the evaluation of results and their comparison with values obtained by applying known predictive formulas of coefficient of permeability and finally, the implementation of the results in creating a predicting model of the groutability of cement suspensions in sands.

No description available.

The goal of this research is to investigate the behavior of polymer concrete confined with a carbon fiber sleeve used as a pile foundation. To evaluate the behavior of a confined polymer concrete pile in this research, four steps was considered. The first step of this investigation considered the mix design of polymer concrete, polymer concrete is a new material which is a combination of epoxy resin and aggregate. Instead of using a traditional mix of cement and water to make concrete, epoxy resin is used. Three dissimilar varieties of aggregate are mixed with different ratios in order to reach the maximum bulk density to obtain the maximum strength. After discovering the optimum ratio which gives the maximum bulk density, several samples of the aggregate are mixed with different ratios of epoxy resin. Next, the samples are investigated in a compression test to observe which ratios have the maximum strength and this ratio is used for a polymer concrete mix design to create a pile foundation. The pile is a built using a cast in place method and confined with a sleeve of carbon fiber. The second part of this investigation determined the structural mechanical properties of confined polymer concrete pile material. The unconfined and confined polymer concrete was tested in compression to determine compressive strength and stress-strain behavior. Similar tests were conducted on unconfined and confined cement concrete for comparison between these materials. Additional tension tests were conducted on unconfined polymer concrete. Then, a carbon fiber sleeve was tested in compression test to determine tensile strength and tension stress-strain behavior. After these tests, the confined polymer concrete is modeled in the computer program MATTCAD which is used to calculate the theoretical bending moment capacity and load-displacement curve. Finally, the confined polymer concrete is tested with the MTS 311 Load Frame in three point load flexure test to determine the experimentally bending moment capacity, load-displacement curve and compare with theoretical results. Confined polymer concrete was tested in one and two way cyclic loading to observe the ductility behavior of this material as laterally loaded piles and compared with cement concrete results in cyclic loading. The third part of this investigation determined the geotechnical mechanical properties of confined polymer concrete pile material. Cyclic Multi Degree of Freedom (CYMDOF) device was used to determine interface reaction and friction angle between confined polymer concrete and soil with interface shear test theory method. Furthermore, the same device was used to determine the friction angle of soil with direct shear test theory, and compare the friction angle results together. The last part of this investigation considered the behavior of different sized confined polymer concrete pile in different types of soil. A confined polymer concrete pile was modeled into PLAXIS and OPENSEES PL computer software to analysis pile in axial load and lateral load respectively. Furthermore, a cement concrete pile was modeled with similar software and conditions to compare these two materials.

To assess the long-term performance of soil-cement materials used in source-control remediation methods (i.e. cement-based solidification/stabilization), procedures to measure or estimate contaminant migration parameters are essential. Previous research indicates that diffusion may be an important mechanism in contaminant transport through soil-cement materials. However, there is a paucity of information regarding the diffusion of contaminants through these materials. The development of a single-reservoir diffusion apparatus and methodology to assess the effective diffusion coefficient (De) and effective porosity (ne) of dissolved, conservative, inorganic chemicals for saturated, cured, monolithic soil-cement specimens is discussed. This is the only study known to investigate these parameters for these materials. The results of tritiated water diffusion tests on 14 different soil-cement mixtures are presented and the influence of curing time and mixture properties such as water-to-cement ratio, cement content, and grain-size distribution are examined. Results suggest that, to determine reasonable assessments of the longer-term parameters, soil-cement samples should be cured for a minimum of 70 days before commencing diffusion testing. Values of ne (0.21 to 0.41) and De (2.50×10-10 m2/s to 7.0×10-10 m2/s) determined are similar to those previously determined for a number other low-hydraulic conductivity materials (i.e. saturated inactive clays). The water content of the initial mixture is shown to have a substantial effect on the diffusive properties as the results indicate that both the total porosity (n) and the effective porosity, ne, generally increase with increasing initial water content. For the range of soils used in this investigation, grain-size distribution did not have a substantial effect on the values of ne or De determined from diffusion testing. The adaptation of a double-reservoir diffusion testing apparatus and methodology to evaluate the distribution coefficient (Kd) and De of organic contaminants is also presented. This apparatus is used to evaluate Kd and De of benzene, ethylbenzene, naphthalene, and trichloroethylene for three soil-cement mixtures. Values of Kd (0 to 2.5 cm3/g depending on the compound and soil-cement mixture tested) determined from diffusion testing, batch testing, and theoretical estimates from the literature were in general agreement. Values of De for the organic compounds ranged from 1.50×10-10 to 3.0×10-10 m2/s.

Water contaminated due to mining activities is often acidic and can contain high concentrations of dissolved metals. Cement kiln dust (CKD) is a fine-grained, alkaline material that is generated as a by-product of cement production. Its high lime (CaO) content makes it attractive as a substitute for quicklime in the generation of slurries for the treatment of mine water. The first part of this study analyzed six CKD samples for several physical and chemical properties to determine their variability and to compare them to the characterization of a commercial quicklime sample. Neutralization and precipitation experiments using acidic mine water containing high concentrations of zinc and iron determined that all slaked CKD slurries performed comparably to the quicklime slurry in terms of precipitation of soluble metals. The results of this research show that CKD can be effectively used to neutralize mine water and precipitate and remove dissolved metals.

Oil companies need to evaluate the risk of annular fluid or gas migration if cement fails during the life of the well. Sustained casing pressure can lead to shutting in the wells to avoid health, safety, and environment (HSE) risks and government fines. To understand the long-term integrity of cement in high temperature and high pressure (HTHP) conditions and the mechanical properties that affect the ability of cements to seal fluids, this project used finite-element models (FEMs) to study the stress-causing phenomena. FEM analyses in ABAQUS version 6.11 were used to determine the potential of cement failure in oil wells. The model uses a 3D section of a well that can be used for different casing and formation types under different loading conditions. The model built in ABAQUS version 6.11 allows incorporating materials with nonlinear mechanical properties; it also uses FEM analysis to forecast fractures inside the cement under different loading scenarios like hydraulic fracture jobs or casing tests. The finite-element model included cases for cement cracking, cement debonding, and plastic deformation of the cement and rock that can generate loss of zonal isolation. Linear manner: set cements behave elastically until a failure criterion is reached, and then they can behave plastically. The FEM approach can reproduce stresses, strains, and volume changes in the material under different environmental HTHP conditions. Cemented wells have both tensile and compressive stresses that make some parts of the cement sheath experience fracture initiation, plastic deformation, or debonding. This dissertation provides a model that will help drillers design the set cement for long-term integrity in HPHT well conditions. The FEM predicts if the cement sheath can develop debonding, cracks or plastic deformations during the life of the well. The cement sheath needs to be designed for long-term zonal isolation to avoid interzonal communications, remedial costs and environmental problems related to cement seal. A CMS™-300 Automated Permeameter, a mechanical properties analyzer, HPHT cement consistometer, annular expansion molds, and tri-axial test equipment were used in this study to test cements for specific applications in three Colombian oil fields, including an oil field with in-situ combustion project.