Diploma thesis focuses on simultaneous transmission of selected photonic services by one single-mode optical fiber. The thesis deals with the problem of common transmission of multiple photonic services by one optical fiber using the wavelength division multiplex technology. Furthermore, the origin and influence of nonlinear phenomena accompanying the simultaneous transmission of photonic services are described. Except common data transmission with a bitrate of 10 Gbit/s, a common high-speed data signal transmission with a bitrate of 200 Gbit/s, accurate time transmission and high-power sensor signal are considered. During the aimultaneous transmission of selected photonic services, the measurement of the transmission parameters was performed for various variants of the simultaneous transmission arrangement. In particular, the influence of nonlinear phenomena and possible mutual interference of individual transmission channels at 50 and 100 GHz between signals was analyzed.

The performance and lifetime of lithium-ion batteries are strongly influenced by their composition. One category of critical components are electrolyte additives, which are included primarily to stabilize electrode/electrolyte interfaces in the battery cells by forming passivation layers. The presented study aimed to identify and study such an additive that could form a hydrogen-evolution-suppressing solid electrolyte interphase (SEI) in lithium-ion batteries based on aqueous electrolytes. A promising molecular additive, ethyl 2,2-difluoroacetate (EDFA), was found to hold the qualities required for an SEI former and was herein further analyzed electrochemically. Analysis of the battery cells were performed with linear sweep voltammetry and cyclic voltammetry with varying scan rate and EDFA concentrations. Results show that both 1 and 10 w-% EDFA in the electrolyte produced hydrogen-evolution-suppressing SEI:s, although the higher concentration provided no apparent benefit. Lithium-ion full-cells based on LiMn2O4 vs. Li4Ti5O12 active materials displayed poor, though partly reversible, dis-/charge cycling despite the operation of the electrode far outside the electrochemical stability window of the electrolyte. Inclusion of reference electrodes in the lithium-ion cells proved to be immensely challenging with unpredictable drifts in their electrode potentials during operation. To summarize, HER-suppressing electrolyte additives are demonstrated to be a promising approach to stabilize high-voltage operation of aqueous lithium-ion cells although further studies are necessary before any practical application thereof can be realized. Electrochemical evaluation of the reaction mechanism and efficiency of the electrolyte additives relies however heavily on the use of reference electrodes and further development thereof is necessary.

Doctor Scientiae (Odontology) - DSc(Odont) / Investigations of pathoses of the oral cavity encompass a relatively wide spectrum of diseases, abnormalities, tumours and tumour-like conditions affecting and occurring in the dental hard tissues and supportive structures, the bony skeleton of the face and the soft tissues of the. mouth. It involves a study of the normal - oral biology - and the abnormal - oral pathology. Oral pathology is a relatively new specialized field of dental science and practice. In South Africa, prior to the nineteen-fifties, research in oral pathology was primarily directed towards dental disease. Two people - Julius Staz of the University of the Witwatersrand and Tony Ockerse of the University of Pretoria - were the doyens in this field and made major contributions to dental science. Staz reported on the status of dental caries and tumorous malformations of teeth and Ockerse on the prevalence and severity of fluorosis in South Africa. During the fifties a second generation of dental surgeons, who were interested in soft tissue, bone and tumour pathology, emerged. They ,were Bertie Cohen, George Baikie, Mervyn Shear and John Lemmer who, at that time, were all from the University of the Witwatersrand. Bertie Cohen later joined the Royal College of Surgeons of England. Mervyn Shear led the field with his research on cysts of the oral cavity. The practice of oral pathology, moulded on anatomical pathology, was established in the early sixties and Mervyn Shear and the author, from the University of Pretoria, became known as oral pathologists. Research at that early stage comprised clinical and histological observations of oral lesions, diseases, tumours and tumour-like conditions. Observation techniques became more sophisticated during the sixties and seventies with the advent of histochemistry and electronmicroscopy. The next major development which blossomed in the seventies and early eighties was the application of epidemiological methods in the study of disease. Epidemiological principles enabled the correct recording of profiles of oral pathoses in the community. Much was learnt about the prevalence and distribution of oral conditions. The application and use of experimental models, especially laboratory animals, became popular in the eighties. Amongst others, a germfree animal unit was established in the Faculty of Dentistry of the University of Stellenbosch enabling workers to study the microbiological aetiology of dental and oral disease. Morphological observations of tumours and mucosal lesions were further enhanced during this period with the development of immunocytochemistry Experimental cell studies by means of cell culture techniques, commenced late in the eighties and was established in the early nineties. These models fostered molecular biology techniques which have become useful tools for the investigation of the aetiology of disease at a cellular and molecular level. At present molecular techniques are also popular in other spheres of oral pathology such as microbiological, immunological and oncological research. The author's first contact with oral pathology as a subject, forming an important and interesting part of dentistry, was the prescribed textbook "Oral and Dental Diseases", 2nd ed., 1951., by HH Stone of the University of Liverpool in the United Kingdom. Subsequently an enduring interest in the subject and research was cultivated by three teachers and colleagues, Ivor Kramer, Robert Bradlow and Mervyn Shear. Ivor Kramer, Professor of Oral Pathology in the Eastman Dental Institute of the University of London was a superb postgraduate teacher of oral pathology, and revelled in research. The Dean of the Institute, Professor Sir Robert Bradlow was a clinician and splendid diagnostician. He correlated the clinical and histopathological features of oral diseases. These two teachers set the course in oral pathology for the author during his postgraduate studies. In the sixties, after a spell at the University of Pretoria, the author joined Professor Mervyn Shear at the University of Witwatersrand. It was here that the author could further his skills of presenting lectures and research papers in an orderely manner and strengthen his love of research. The research carried out by the author reflects to a large extent the development of research in oral pathology in South Africa since 1960.. It includes studies of diseases and lesions of the oral mucosa, the dental hard tissues, tumours of the oral cavity and jaws and forensic odonto-stomatology. To date 139 articles have been published and accepted in scientific journals of which I was the first or co-author. The research presented here, however, comprises only those studies related to pathoses of the oral mucosa as it occurs in South Africa. Fifty-four papers and two abstracts are submitted. The papers are grouped into two divisions which include studies on (I) normal human oral and ectocervical mucosa and (II), those related to pathoses of the oral mucosa. The latter is subdivided into sections on: the profile of lesions of the oral mucosa in the community; cytological, clinical and morphological features of lesions of the oral mucosa; and studies on the aetiology of lesions of the oral mucosa. Each division and section is preceded by a declaration as to the contribution of the author or co-authors and a précis of the aims, objects and research findings. In the introduction of the précis statements are made explaining the aims of the study. These statements are not referenced because they appear in the respective articles.

Chalcogenide glasses are highly nonlinear optical materials which can be used for fabricating active and passive photonic devices. This thesis work deals with the fabrication of buried, three dimensional, channel waveguides in chalcogenide glasses, using ultrafast laser inscription technique. The femtosecond laser pulses are focused into rare earth ions doped and undoped chalcogenide glasses, few hundred microns below from the surface to modify the physical properties such as refractive index, density, etc. These changes are made use in the fabrication of active and passive photonic waveguides which have applications in integrated optics. The first chapter provides an introduction to the fundamental aspects of femtosecond laser inscription, laser interaction with matter and chalcogenide glasses for photonic applications. The advantages and applications of chalcogenide glasses are also described. Motivation and overview of the present thesis work have been discussed at the end. The methods of chalcogenide glass preparation, waveguide fabrication and characterization of the glasses investigated are described in the second chapter. Also, the details of the experiments undertaken, namely, loss (passive insertion loss) and gain measurements (active) and nanoindentation studies are outlined. Chapter three presents a study on the effect of net fluence on waveguide formation. A heat diffusion model has been used to solve the waveguide cross-section. The waveguide formation in GeGaS chalcogenide glasses using the ultrafast laser, has been analyzed in the light of a finite element thermal diffusion model. The relation between the net fluence and waveguide cross section diameter has been verified using the experimentally measured properties and theoretically predicted values. Chapter four presents a study on waveguide fabrication on Er doped Chalcogenide glass. The active and passive characterization is done and the optimal waveguide fabrication parameters are given, along with gain properties for Er doped GeGaS glass. A C-band waveguide amplifier has been demonstrated on Chalcogenide glasses using ultrafast laser inscription technique. A study on the mechanical properties of the waveguide, undertaken using the nanoindentation technique, is presented in the fifth chapter. This work brings out the close relation between the change in mechanical properties such as elastic modulus and hardness of the material under the irradiation of ultrafast laser after the waveguide formation. Also, a threshold value of the modulus and hardness for characterizing the modes of the waveguide is suggested. Finally, the chapter six provides a summary of work undertaken and also discusses the future work to be carried out.

[EN] The processing of radiofrequency signals using photonics means is a discipline that appeared almost at the same time as the laser and the optical fibre. Photonics offers the capability of managing broadband radiofrequency (RF) signals thanks to its low transmission attenuation, a variety of linear and non-linear phenomena and, recently, the potential to implement integrated photonic subsystems. These features open the door for the implementation of multiple functionalities including optical transportation, up and down frequency conversion, optical RF filtering, signal multiplexing, de-multiplexing, routing and switching, optical sampling, tone generation, delay control, beamforming and photonic generation of digital modulations, and even a combination of several of these functionalities. This thesis is focused on the application of vector processing in the optical domain to radiofrequency signals in two fields of application: optical beamforming, and photonic vector modulation and demodulation of digital quadrature amplitude modulations. The photonic vector control enables to adjust the amplitude and phase of the radiofrequency signals in the optical domain, which is the fundamental processing that is required in different applications such as beamforming networks for direct radiating array (DRA) antennas and multilevel quadrature modulation. The work described in this thesis include different techniques for implementing a photonic version of beamforming networks for direct radiating arrays (DRA) known as optical beamforming networks (OBFN), with the objectives of providing a precise control in terrestrial applications of broadband signals at very high frequencies above 40 GHz in communication antennas, optimizing the size and mass when compared with the electrical counterparts in space application, and presenting new photonic-based OBFN functionalities. Thus, two families of OBFNs are studied: fibre-based true time delay architectures and integrated networks. The first allow the control of broadband signals using dispersive optical fibres with wavelength division multiplexing techniques and advanced functionalities such as direction of arrival estimation in receiving architectures. In the second, passive OBFNs based on monolithically-integrated Optical Butler Matrices are studied, including an ultra-compact solution using optical heterodyne techniques in silicon-on-insulator (SOI) material, and an alternative implementing a homodyne counterpart in germanium doped silica material. In this thesis, the application of photonic vector processing to the generation of quadrature digital modulations has also been investigated. Multilevel modulations are based on encoding digital information in discrete states of phase and amplitude of an electrical signal to enhance spectral efficiency, as for instance, in quadrature modulation. The signal process required for generating and demodulating this kind of signals involves vector processing (phase and amplitude control) and frequency conversion. Unlike the common electronic or digital implementation, in this thesis, different photonic based signal processing techniques are studied to produce digital modulation (photonic vector modulation, PVM) and demodulation (PVdM). These techniques are of particular interest in the case of broadband signals where the data rate required to be managed is in the order of gigabit per second, for applications like wireless backhauling of metro optical networks (known as fibre-to-the-air). The techniques described use optical dispersion in optical fibres, wavelength division multiplexing and photonic up/down conversion. Additionally, an optical heterodyne solution implemented monolithically in a photonic integrated circuit (PIC) is also described. / [ES] El procesamiento de señales de radiofrecuencia (RF) utilizando medios fotónicos es una disciplina que apareció casi al mismo tiempo que el láser y la fibra óptica. La fotónica ofrece la capacidad de manipular señales de radiofrecuencia de banda ancha, una baja atenuación, procesados basados en una amplia variedad de fenómenos lineales y no lineales y, recientemente, el potencial para implementar subsistemas fotónicos integrados. Estas características ofrecen un gran potencial para la implementación de múltiples funcionalidades incluyendo transporte óptico, conversión de frecuencia, filtrado óptico de RF, multiplexación y demultiplexación de señales, encaminamiento y conmutación, muestreo óptico, generación de tonos, líneas de retardo, conformación de haz en agrupaciones de antenas o generación fotónica de modulaciones digitales, e incluso una combinación de varias de estas funcionalidades. Esta tesis se centra en la aplicación del procesamiento vectorial en el dominio óptico de señales de radiofrecuencia en dos campos de aplicación: la conformación óptica de haces y la modulación y demodulación vectorial fotónica de señales digitales en cuadratura. El control fotónico vectorial permite manipular la amplitud y fase de las señales de radiofrecuencia en el dominio óptico, que es el procesamiento fundamental que se requiere en diferentes aplicaciones tales como las redes de conformación de haces para agrupaciones de antenas y en la modulación en cuadratura. El trabajo descrito en esta tesis incluye diferentes técnicas para implementar una versión fotónica de las redes de conformación de haces de en agrupaciones de antenas, conocidas como redes ópticas de conformación de haces (OBFN). Se estudian dos familias de redes: arquitecturas de retardo en fibra óptica y arquitecturas integradas. Las primeras permiten el control de señales de banda ancha utilizando fibras ópticas dispersivas con técnicas de multiplexado por división de longitud de onda y funcionalidades avanzadas tales como la estimación del ángulo de llegada de la señal en la antena receptora. En la segunda, se estudian redes de conformación pasivas basadas en Matrices de Butler ópticas integradas, incluyendo una solución ultra-compacta utilizando técnicas ópticas heterodinas en silicio sobre aislante (SOI), y una alternativa homodina en sílice dopado con germanio. En esta tesis, también se han investigado técnicas de procesado vectorial fotónico para la generación de modulaciones digitales en cuadratura. Las modulaciones multinivel codifican la información digital en estados discretos de fase y amplitud de una señal eléctrica para aumentar su eficiencia espectral, como por ejemplo la modulación en cuadratura. El procesado necesario para generar y demodular este tipo de señales implica el procesamiento vectorial (control de amplitud y fase) y la conversión de frecuencia. A diferencia de la implementación electrónica o digital convencional, en esta tesis se estudian diferentes técnicas de procesado fotónico tanto para la generación de modulaciones digitales (modulación vectorial fotónica, PVM) como para su demodulación (PVdM). Esto es de particular interés en el caso de señales de banda ancha, donde la velocidad de datos requerida es del orden de gigabits por segundo, para aplicaciones como backhaul inalámbrico de redes ópticas metropolitanas (conocida como fibra hasta el aire). Las técnicas descritas se basan en explotar la dispersión cromática de la fibra óptica, la multiplexación por división de longitud de onda y la conversión en frecuencia. Además, se presenta una solución heterodina implementada monolíticamente en un circuito integrado fotónico (PIC). / [CA] El processament de senyals de radiofreqüència (RF) utilitzant mitjans fotònics és una disciplina que va aparèixer gairebé al mateix temps que el làser i la fibra òptica. La fotònica ofereix la capacitat de manipular senyals de radiofreqüència de banda ampla, una baixa atenuació, processats basats en una àmplia varietat de fenòmens lineals i no lineals i, recentment, el potencial per implementar subsistemes fotònics integrats. Aquestes característiques ofereixen un gran potencial per a la implementació de múltiples funcionalitats incloent transport òptic, conversió de freqüència, filtrat òptic de RF, multiplexació i demultiplexació de senyals, encaminament i commutació, mostreig òptic, generació de tons, línies de retard, conformació de feix en agrupacions d'antenes i la generació fotònica de modulacions digitals, i fins i tot una combinació de diverses d'aquestes funcionalitats. Aquesta tesi es centra en l'aplicació del processament vectorial en el domini òptic de senyals de radiofreqüència en dos camps d'aplicació: la conformació òptica de feixos i la modulació i demodulació vectorial fotònica de senyals digitals en quadratura. El control fotònic vectorial permet manipular l'amplitud i la fase dels senyals de radiofreqüència en el domini òptic, que és el processament fonamental que es requereix en diferents aplicacions com ara les xarxes de conformació de feixos per agrupacions d'antenes i en modulació multinivell. El treball descrit en aquesta tesi inclou diferents tècniques per implementar una versió fotònica de les xarxes de conformació de feixos en agrupacions d'antenes, conegudes com a xarxes òptiques de conformació de feixos (OBFN), amb els objectius de proporcionar un control precís en aplicacions terrestres de senyals de banda ampla a freqüències molt altes per sobre de 40 GHz en antenes de comunicacions, optimitzant la mida i el pes quan es compara amb els homòlegs elèctrics en aplicacions espacials, i la presentació de noves funcionalitats fotòniques per agrupacions d'antenes. Per tant, s'estudien dues famílies de OBFNs: arquitectures de retard en fibra òptica i arquitectures integrades. Les primeres permeten el control de senyals de banda ampla utilitzant fibres òptiques dispersives amb tècniques de multiplexació per divisió en longitud d'ona i funcionalitats avançades com ara l'estimació de l'angle d'arribada del senyal a l'antena receptora. A la segona, s'estudien xarxes de conformació passives basades en Matrius de Butler òptiques en fotònica integrada, incloent una solució ultra-compacta utilitzant tècniques òptiques heterodinas en silici sobre aïllant (SOI), i una alternativa homodina en sílice dopat amb germani. D'altra banda, també s'ha investigat en aquesta tesi tècniques de processament vectorial fotònic per a la generació de modulacions digitals en quadratura. Les modulacions multinivell codifiquen la informació digital en estats discrets de fase i amplitud d'un senyal elèctric per augmentar la seva eficiència espectral, com ara la modulació en quadratura. El processat necessari per generar i desmodular aquest tipus de senyals implica el processament vectorial (control d'amplitud i fase) i la conversió de freqüència. A diferència de la implementació electrònica o digital convencional, en aquesta tesi s'estudien diferents tècniques de processament fotònic tant per a la generació de modulacions digitals (modulació vectorial fotònica, PVM) com per la seva demodulació (PVdM). Això és de particular interès en el cas de senyals de banda ampla, on la velocitat de dades requerida és de l'ordre de gigabits per segon, per a aplicacions com backhaul sense fils de xarxes òptiques metropolitanes (coneguda com fibra fins l'aire). Les tècniques descrites es basen en explotar la dispersió cromàtica de la fibra òptica, la multiplexació per divisió en longitud d'ona i la conversió en freqüència. A més, es prese / Piqueras Ruipérez, MÁ. (2016). Photonic Vector Processing Techniques for Radiofrequency Signals [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/63264