No description available.

No description available.

No description available.

No description available.

Recent imaging studies have provided a new conceptual model of the internal structure of direct injection diesel fuel jets as well as empirical correlations predicting jet development and structure. This information was used to create a diesel cycle simulation model using C language including compression, fuel injection and combustion, and expansion processes. Empirical relationships were used to create a new mixing-limited zero-dimensional model of the diesel combustion process. During fuel injection five zones were created to model the reacting fuel jet: 1) liquid phase fuel 2) vapor phase fuel 3) rich premixed products 4) diffusion flame sheath 5) surrounding bulk gas. Temperature and composition in each zone is calculated. Composition in combusting zones was calculated using an equilibrium model that includes 21 species. Sub models for ignition delay, premixed burn duration, heat release rate, and heat transfer were also included. Apparent heat release rate results of the model were compared with data from a constant volume combustion vessel and two single-cylinder direct injection diesel engines. The modeled heat release results included all basic features of diesel combustion. Expected trends were seen in the ignition delay and premixed burn model studies, but the model is not predictive. The rise in heat release rate due to the diffusion burn is over-predicted in all cases. The shape of the heat release rate for the constant volume chamber is well characterized by the model, as is the peak heat release rate. The shape produced for the diffusion burn in the engine cases is not correct. The injector in the combustion vessel has a single nozzle and greater distance to the wall reducing or eliminating wall effects and jet interaction effects. Interactions between jets and the use of a spray penetration correlation developed for non-reacting jets contribute to inaccuracies in the model.

With increasing effects of global warming, efforts are made to make transportation in general more fuel efficient. When it comes to internal combustion engines, the most common way to improve fuel efficiency is through ‘downsizing’. Downsizing means that a smaller engine (with lower losses and less weight) performs the task of a larger engine. This is accomplished by fitting the smaller engine with a turbocharger, to recover some of the energy in the hot exhaust gases. Such engine systems need careful optimization and when designing an engine system it is common to use simplified flow models of the complex geometries involved. The exhaust valves and ports are usually modelled as straight pipe flows with a corresponding discharge or loss coefficient, typically determined through steady-flow experiments with a fixed valve and at low pressure ratios across the valve. This means that the flow is assumed to be independent of pressure ratio and quasi-steady. In the present work these two assumptions have been experimentally tested by comparing measurements of discharge coefficient under steady and dynamic conditions. The steady flow experiments were performed in a flow bench, with a maximum mass flow of 0.5 kg/s at pressures up to 500 kPa. The dynamic measurements were performed on a pressurized, 2 litre, fixed volume cylinder with one or two moving valves. Since the volume of the cylinder is fixed, the experiments were only concerned with the blowdown phase, i.e. the initial part of the exhaustion process. Initially in the experiments the valve was closed and the cylinder was pressurized. Once the desired initial pressure (typically in the range 300-500 kPa) was reached, the valve was opened using an electromagnetic linear motor, with a lift profile corresponding to different equivalent engine speeds (in the range 800-1350 rpm). The results of this investigation show that neither the quasi-steady assumption nor the assumption of pressure-ratio independence holds. This means that if simulations of the exhaustion process is made, the discharge coefficient needs to be determined using dynamic experiments with realistic pressure ratios. Also a measure of the quasi-steadiness has been defined, relating the change in upstream conditions to the valve motion, i.e. the change in flow restriction, and this measure has been used to explain why the process cannot be regarded as quasi-steady. / <p>QC 20170306</p>

No description available.

No description available.

Internal combustion engines developments are driven by emissions reduction and energetic efficiency increase. To reach the next standards, downsized/downspeeded engines are required to reduce fuel consumption and CO2 emissions. These techniques place an important demand on the charging system and force the introduction of multistage boosting architectures. With many possible arrangements and large number of parameter to optimize, these architectures present higher complexity than current systems. The objective of this thesis has thus been to investigate the potential of two-stage boosting architectures to establish, for the particular case of passenger car downsized/downspeeded Diesel engines, the most efficient solutions for achieving the forthcoming CO2 emissions targets. To respond to this objective, an exhaustive literature review of all existing solutions has first been performed to determinate the most promising two-stage boosting architectures. Then, a new matching methodology has been defined to optimize the architectures with, on the one hand the development of a new turbine characteristic maps representation allowing straight forward matching calculations and, on the other hand, the development of a complete 0D engine model able to predict, within a reduced computational time, the behavior of any boosting architecture in both steady state and transient operating conditions. Finally, a large parametric study has been carried out to analyze and compare the different architectures on the same base engines, to characterize the impacts of thermo-mechanical limits and turbocharger size on engine performance, and to quantify for different engine development options their potential improvements in term of fuel consumption, maximum power and fun to drive. As main contributions, the thesis provides new modeling tools for efficient matching calculations and synthesizes the main trends in advanced boosting systems to guide future passenger car Diesel engine develop / Varnier ., ON. (2012). Trends and Limits of Two-Stage Boosting Systems for Automotive Diesel Engines [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/16880

A modelagem de motores a combustão interna deve grande parte de sua importância ao uso de unidades de controle eletrônicas que buscam gerenciar as funções do motor. De forma a fornecer melhor suporte para o projetista de controle, a modelagem oferece informações que servem de planta, sobre a qual estratégias de controle serão desenvolvidas. Nesta dissertação, procurou-se estudar e modelar cinco fenômenos: a admissão de ar e de combustível, a produção de energia efetiva através da combustão, a evolução térmica do motor e o comportamento dos gases no sistema de exaustão. Investigou-se também, em todos estes fenômenos, a influência do uso de composição variada gasolina/etanol. Na admissão de ar, buscou-se estudar como a abertura da válvula borboleta e a velocidade do motor influenciam no fluxo de ar admitido, ponderando esta grandeza através de um fator de correção denominado eficiência volumétrica. Na admissão de combustível, no caso modelada para motores com injeção indireta na porta, procurou-se explanar quantitativamente sobre os diversos aspectos que influenciam a evaporação do combustível. Na geração de energia útil, priorizou-se a análise de como as características do motor e da combustão afetam a produção de torque. Na evolução térmica do motor, examinaram-se os principais fluxos energéticos do motor e os aspectos que os influenciam. Ademais, foram executadas as validações dos modelos levantados para o motor EA 111 VHT 1.6l. Os resultados, com seus respectivos erros, podem ser encontrados neste trabalho. / The internal combustion engine modeling owes big part of its importance to the use of electronic control units that aim to manage the engine functions. To provide better support to the control designer, the modeling offers information that can compose the plant, on which control strategies will be developed. In this master thesis, it was sought to study and to model five phenomena: the air intake and the fuel admission, the effective energy production from the combustion, the engine thermic evolution and the gas behavior in the exhaust system. It was also considered how the influence of the gasoline/ethanol varied composition affects all these phenomena. In the air intake, it was studied how the butterfly valve opening and the engine speed influence the intake air flow, pondering this variable through a correction factor named volumetric efficiency. In the fuel admission, in the case of this study modelled for port-fuel injection engines, it was attempted to explain quantitatively the many aspects that influence the fuel evaporation. In the mechanical energy generation, it was prioritized the analysis about how the engine and combustion characteristics affect the torque production. In the engine thermic evolution, it was examined the major energy flows and the aspects that influence them. Also, the validations of the models raised for the EA 111 VHT 1.6l engine were executed. The results, with its respective errors, can be found in this work.