abstract: Mixed-ionic electronic conducting (MIEC) oxides have drawn much attention from researchers because of their potential in high temperature separation processes. Among many materials available, perovskite type and fluorite type oxides are the most studied for their excellent oxygen ion transport property. These oxides not only can be oxygen adsorbent or O2-permeable membranes themselves, but also can be incorporated with molten carbonate to form dual-phase membranes for CO2 separation. Oxygen sorption/desorption properties of perovskite oxides with and without oxygen vacancy were investigated first by thermogravimetric analysis (TGA) and fixed-bed experiments. The oxide with unique disorder-order phase transition during desorption exhibited an enhanced oxygen desorption rate during the TGA measurement but not in fixed-bed demonstrations. The difference in oxygen desorption rate is due to much higher oxygen partial pressure surrounding the sorbent during the fixed-bed oxygen desorption process, as revealed by X-ray diffraction (XRD) patterns of rapidly quenched samples. Research on using perovskite oxides as CO2-permeable dual-phase membranes was subsequently conducted. Two CO2-resistant MIEC perovskite ceramics, Pr0.6Sr0.4Co0.2Fe0.8 O3-δ (PSCF) and SrFe0.9Ta0.1O3-δ (SFT) were chosen as support materials for membrane synthesis. PSCF-molten carbonate (MC) and SFT-MC membranes were prepared for CO2-O2 counter-permeation. The geometric factors for the carbonate phase and ceramic phase were used to calculate the effective carbonate and oxygen ionic conductivity in the carbonate and ceramic phase. When tested in CO2-O2 counter-permeation set-up, CO2 flux showed negligible change, but O2 flux decreased by 10-32% compared with single-component permeation. With CO2 counter-permeation, the total oxygen permeation flux is higher than that without counter-permeation. A new concept of CO2-permselective membrane reactor for hydrogen production via steam reforming of methane (SRM) was demonstrated. The results of SRM in the membrane reactor confirm that in-situ CO2 removal effectively promotes water-gas shift conversion and thus enhances hydrogen yield. A modeling study was also conducted to assess the performance of the membrane reactor in high-pressure feed/vacuum sweep conditions, which were not carried out due to limitations in current membrane testing set-up. When 5 atm feed pressure and 10-3 atm sweep pressure were applied, the membrane reactor can produce over 99% hydrogen stream in simulation. / Dissertation/Thesis / Doctoral Dissertation Chemical Engineering 2020

Mixed Matrix Membranes (MMMs) have received worldwide attention during the last decades. This is due to the fact that the resulting materials can combine the good processability and low cost of polymer membranes with the diverse functionality, high performance and thermal properties of the fillers. This work explores the fabrication and application of MMMs. We focused on the design and fabrication of nanofillers to impart target functionality to the membrane for water treatment, protective coating and gas separation. This thesis is divided into three sections according to the application including: I- Water Treatment: This part is divided into three chapters, two related to the membrane distillation (MD) and one related to the oil spill. Three different nanofillers have been used: Periodic mesoporous organosilica (PMO), graphene and carbon nanotube (CNT). Those nanofillers were homogeneously incorporated into polyetherimide (PEI) electrospun nanofiber membranes. The doped nanoparticle not only improved the mechanical properties and thermal stability of the pristine fiber but also enhanced the MD and oil spill performance due to the functionality of those nanofillers. II- Protective coating: This part includes two chapters describing the design and the fabrication of a smart antibacterial and anti-corrosion coating. In the first project, we fabricated colloidal lysozyme-templated gold nanoclusters gating antimicrobial-loaded silica nanoparticles (MSN-AuNCs@lys) as nano-fillers in poly(ethylene oxide)/poly(butylene terephthalate) polymer matrix. MSN-AuNCs@lys dispersed homogeneously within the polymer matrix with zero NPs leaching. The system was coated on a common radiographic dental imaging device that is prone to oral bacteria contamination. This coating can successfully sense and inhibit bacterial contamination via a controlled release mechanism that is only triggered by bacteria. In the second project, the coaxial electrospinning approach has been applied to fabricate smart core-shell nanofiber for controlled release of anti-corrosion material. Acetal-dextran was used as a pH controlled shell of the fibers and polyvinyl alcohol (PVA) as a hydrophilic core. Caffeine, as an anti-corrosion inhibitor was encapsulated in the fiber core to test its potential application as an anticorrosion coating. The almost negligible release was noticed at neutral pH. In acidic pH due to corrosion, the fibers quickly respond by releasing caffeine cargo. III- Gas separation: We describe the synthesis and application of novel ethylene-diamine-based PMO. The novel nanoparticles were homogeneously incorporated into polydimethylsiloxane to fabricate a MMMs thin layer on a porous polyacrylonitrile support. Our results prove that our PMOs can be used as nanofillers to enhance the CO2 selectivity of the PDMS polymer.

To date there exists a great deal of energetic and economic inefficiency in the separation of olefins from paraffins because the principal means of achieving industrial purity requirements is accomplished with very energy intensive cryogenic distillation. Mitigation of the severe energy intensity of the propylene/propane separation has been identified as one of seven chemical separations which can change the landscape of global energy use, and membranes have been targeted as an emerging technology because they offer scalability and lower capital and operating costs. The focus of this work was to evaluate a new direction of material development for the very industrially relevant propylene/propane separation using membranes. The objective was to develop a rational design approach for generating highly selective membranes using a relatively new platform of materials known as polyimides of intrinsic microporosity (PIM-PIs), the prospects of which have never been examined for the propylene/propane separation. Structurally, PIMs comprise relatively inflexible macromolecular architectures integrating contortion sites that help disrupt packing and trap microporous free volume elements (< 20 Å). To date most of the work reported in the literature on this separation is based on conventional low free volume 6FDA-based polyimides which in the best case show moderate C3H6/C3H8 selectivities (<20) with C3H6 permeabilities too low to garner industrial interest. Due to propylene and propane’s relatively large molecular size, we hypothesized that the use of more open structures can provide greater accessibility to the pores necessary to enhance membrane sieving and flux. It has been shown for numerous key gas separations that introduction of microporosity into a polymer structure can defy the notorious permeability/selectivity tradeoff curve and induce simultaneous boosts in both permeability and selectivity. The cornerstone approach to designing state of the art high performance PIM-PI membranes for the light gas separations involving maximizing the intra-segmental rigidity of the polymer chain was applied to the C3H6/C3H8 separation. A study regarding a stepwise maximization of intra-molecular rigidity and its effects on C3H6/C3H8 permeation was evaluated by conducting systematic structural modifications to high performance PIM-PIs. State of the art increases in performance were observed in pure-gas measurements as there were significant increases in C3H6/C3H8 selectivity and C3H6 permeability upon doing so. However, mixed-gas measurements showed that there were 65% losses in selectivity due to competitive sorption and mainly plasticization. Based on the conclusions drawn, a fundamental departure from conventional PIM design principles was used, instead emphasizing enhancing inter-chain interactions by introduction of a flexible diamine and functionalization with hydroxyl groups to attempt to immobilize the polymer chains. In doing so, the polymer chains may be able to pack more efficiently and upon sub-Tg annealing cause a microstructural reorganization to form a coplanarized configuration due to the combination of inter-chain charge transfer complexes (CTC) and hydrogen bonding networks. This approach successfully mitigated plasticization, but more importantly resulted in a tightening of the microstructure, especially in the ultra-microporous range (<7 Å) thereby yielding significant boosts in C3H6/C3H8 selectivity. Based on the PIM platform and novel polymer design approach thereof, the C3H6/C3H8 upper bound was thrust to new limits and led to the generation of the most selective solution processable polymers reported for the C3H6/C3H8 separation. Although the PIM platform has redefined the polymer upper bound, the permeability/selectivity tradeoff still endures, as the C3H6 permeabilities were on the order of 1 to 3.5 Barrer for the most selective polymers. To bridge that gap in permeability, several different approaches were taken. For the first time attempted for C3H6/C3H8 separation, high temperature heating of a PIM-PI to form thermally-rearranged and carbon molecular sieve membranes was employed. The TR membrane showed increased C3H6 permeability and about 50% losses in C3H6/C3H8 selectivity, while the CMS membrane formed at 600 oC showed modest gains in C3H6/C3H8 selectivity with significant improvements in C3H6 permeability. Finally, hybrid nanocomposite membranes incorporating a metal-organic framework structure into a PIM-PI matrix was used. ZIF-8, which has demonstrated high diffusive selectivities for C3H6/C3H8, was dispersed within the polymer, since previous work by the Koros group indicated that its incorporation into polyimide matrices can facilitate major improvements in both C3H6/C3H8 selectivity and C3H6 permeability compared to the respective neat polymer. Focus was directed towards attempting to improve polymer/nanoparticle adhesion by enhancing the interactions between the polymer and filler particles to mitigate the interfacial defects notorious in mixed-matrix membranes (MMM). To do so, ZIF-8 was dispersed into one of the best performing hydroxyl functionalized PIM-PI for the C3H6/C3H8 separation. The highest loaded mixed-matrix membrane in a glassy polymer to date of 65% (w/w) was achieved. The membranes showed pure-gas selectivities ranging from 34 with 10 Barrer at 30% loading to 43 with 38 Barrer at 65% loading. Strong performance and plasticization resistance were sustained in mixed-gas experiments even to feed pressures approaching the vapor pressure of the C3H6/C3H8 mixture, as selectivities well over 20 were achieved with high permeabilities, thereby demonstrating the potential commercial viability. Based on the work reported in this dissertation, we hope to help lay a framework to be able to tailor membrane performance and future membrane design to meet the demands of the different applications of the propylene/propane separation and hence show that there can be a marketplace for membranes in the separation. These include the debottlenecking of cryogenic distillation towers for production of polymer-grade propylene (99.5%) to reduce the associated extensive energy load, production of chemical-grade propylene (92-95% propylene), or for the recovery and recycling of olefins from reactor purges of petrochemical processes.

The Diploma thesis is devoted to the absorption of gases by the experimental gas scrubber. The main attention of the theoretical part is focused on the description of absorption, kinetics and the equilibrium between gas and liquid phase. Experimental part is concentrated on the absorption of carbon dioxide to deionized water in the experimental scrubber. Finally, experimental data are discussed.

The entire world including Saudi Arabia is dependent on natural gas to provide new energy supplies for the future. Conventional ways for gas separation are expensive, and, hence, it is very important to reduce the cost and lower the energy consumption. Membrane technology is a relatively new separation process for natural gas purification with large growth potential, specifically for off-shore applications. The economics of any membrane separation process depend primarily on the intrinsic gas permeation properties of the membrane materials. All current commercial membranes for natural gas separation are made from polymers, which have several drawbacks, including low permeability, moderate selectivity, and poor stability in acid gas and hydrocarbon environments. The recent development of polymeric materials called “polymers of intrinsic microporosity” (PIMs) provide a new class of high-performance membrane materials that are anticipated to be used in natural gas separation processes including, but not limited to, acid gas removal and separation of hydrocarbons from methane. PIM-7 is an excellent example of a material from the PIMs series for gas separation. It was selected for this work since it has not been extensively tested for its gas permeation properties to date. Specifically, sorption and mixed-gas permeation data were not available for PIM-7 prior to this work. Sorption isotherms of N2, O2, CH4, CO2, C2H6, C3H8 and n-C4H10 were determined over a range of pressures at 35 oC for PIM-7 using a custom-designed dual-volume pressure decay system. Condensable hydrocarbon gases, such as C3H8 and n-C4H10, show significantly higher solubility than the other less condensable gas of the test series due to their high affinity to the polymer matrix. Dual-mode sorption model parameters were determined from the sorption isotherms. Henry’s law solubility, Langmuir capacity constant and the affinity constant increased with gas condensability. Permeability coefficients of He, H2, N2, O2, CH4, CO2, C2H6, C3H8 and n-C4H10 were measured at 35 oC and 2 atm feed pressure using a home-made constant-volume/variable pressure pure-gas permeation system. Hydrocarbon-induced plasticization of PIM-7 was confirmed by measuring the permeability coefficients of C3H8 and n-C4H10 as function of pressure at 35 oC. Diffusion coefficients were calculated from the permeability and solubility data at 2 atm for all penetrants tested and as function of pressure for C3H8 and n-C4H10; the values for C3 and C4 increased significantly with pressure because of plasticization. Physical aging was studied by measuring the permeability coefficients of a number of gases in fresh and aged films. Mixed-gas permeation tests were performed for a feed mixture of 2 vol% n-butane and 98 vol% methane. Based on BET surface area measurements using N2 as a probe molecule, PIM-7 is a microporous polymer (S = 690 m2/g) and it was expected to exhibit selectivity for n-butane over methane, as previously observed for other microporous polymers, such as PIM-1 and PTMSP. Surprisingly, PIM-7 is more permeable to methane than n-butane and exhibits a mixed-gas methane/n-butane selectivity of up to 2.3. This result indicates that the micropore size in PIM-7 is smaller than that in other PIMs materials. Consequently, PIM-7 is not a suitable candidate membrane material for separation of higher hydrocarbons from methane.

Since the discovery of size-selective metal-organic frameworks (MOF) researchers have tried to manufacture them into gas separation membranes. ZIF-8 became the most studied MOF for membrane applications mainly because of its simple synthesis, good chemical and thermal stability, recent commercial availability and attractive pore size. The aim of this work is to develop convenient methods for growing ZIF thin layers on polymer supports to obtain defect-free ZIF membranes with good gas separation properties. We present new approaches for ZIF membranes preparation on polymers. We introduce zinc oxide nanoparticles in the support as a secondary metal source for ZIF-8 growth. Initially the ZnO particles were incorporated into the polymer matrix and later on the surface of the polymer by magnetron sputtering. In both cases, the ZnO facilitated to create more nucleation opportunities and improved the ZIF-8 growth compared to the synthesis without using ZnO. By employing the secondary seeded growth method, we were able to obtain thin (900 nm) ZIF-8 layer with good gas separation performance. Next, we propose a metal-chelating polymer as a suitable support for growing ZIF layers. Defect-free ZIF-8 films with a thickness of 600 nm could be obtained by a contra-diffusion method. ZIF-8 membranes were tested for permeation of hydrogen and hydrocarbons, and one of the highest selectivities reported so far for hydrogen/propane, and propylene/propane was obtained. Another promising method to facilitate the growth of MOFs on polymeric supports is the chemical functionalization of the support surface with functional groups, which can complex metal ions and which can covalently bond the MOF crystals. We functionalized the surface of a common porous polymeric membrane with amine groups, which took part in the reaction to form ZIF-8 nanocrystals. We observed an enhancement in adhesion between the ZIF layer and the support. The effect of parameters of the contra-diffusion experiment (such as temperature lower than room temperature and synthesis times shorter than 1 hour) on ZIF-8 membrane properties was evaluated. We could prepare one of the thinnest (around 200 nm) yet selective ZIF-8 films reported.

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第19686号 / 工博第4141号 / 新制||工||1639(附属図書館) / 32722 / 京都大学大学院工学研究科航空宇宙工学専攻 / (主査)教授 稲室 隆二, 教授 青木 一生講師杉元 宏 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

No description available.

Membrane processes have received growing attention due to their low energy consumption and ease of operation. Thin-film composite reverse osmosis membranes based on polyamides are the most widely applied commercial membranes, because of their high flux and selectivity. However, their application for gas separation processes is still limited. This is the due to the presence of defects in the membrane when in the dry state. Traditionally, thin-film composite membranes are made by interfacial polymerization between a polar (aqueous) phase and a non-polar (organic) phase. The most commonly applied thin-film composite membranes are made by dissolving m-phenylene diamine in the aqueous phase and trimesoyl chloride in the organic phase. This work investigated the possibility of fabricating thin-film composite membranes when an aliphatic alcohol (methanol, ethanol or isopropanol) is used as the polar phase. This is further extended to examining the ability of a PDMS coating to plug the defects in such layers. The effects of temperature and support type on the membrane performance were also studied. Solubility tests were conducted to determine the solubility limit of commercial and in-house fabricated amine monomers in water, methanol, ethanol and isopropanol. Water-insoluble monomers were found to be soluble in ethanol and methanol. Gas permeation tests were conducted on membranes made using water, methanol, ethanol and isopropanol as the polar phase. The results showed that the membranes produced by aliphatic alcohols had higher selectivities. The highest H2/CO2 selectivity of ~ 26 was observed in the ethanol-based membranes when they were coated with PDMS and tested at 80 C. It was confirmed that PDMS is able to plug the defects in the membrane. Membranes made on the polysulfone support were found to have higher permeance and comparable selectivity relative to the membranes made on the polyacrylonitrile supports. It was also found that a change in the polar phase solvent is able to alter the morphology of the membranes. SEM micrographs showed clear differences in the surface structure of each membrane. The average thickness values obtained from ellipsometry measurements showed a correlation with the interface miscibility. The thickest membrane corresponded to the most miscible interface (IPA/Isopar).

Metal Organic Frameworks (MOFs) are a class of porous materials that are predominantly obtained as powders and have been investigated as a solid sorbent for gas separation or carbon capture applications from combustion exhaust gases. The manufacturing of products with MOFs to use them for real life applications is still a major problem. The most common productization method used is to form pellets of the powder MOFs. This has a limitation on the product shape which makes it difficult for it to be used in gas separation applications. This study focuses on using additive manufacturing technique to give MOFs a lattice (mesh-like) geometry which is useful for gas separation applications as the mixture of gases would be able to pass through the lattice structure and be separated due to the inherent MOF properties and characteristics. Two MOFs based on magnesium and manganese salts have been studied in this project. An extrudable paste developed using alginate gel as a binder with these MOFs. With alterations in paste formulations and 3D printer parameters, lattice structures were printed using the two MOFs. CO2 and N2 gas uptakes were measured showing that the structure adsorbs CO2 gas to a higher extend which results in the separation of N2 gas in both materials. When compared to their pristine powder form, other properties of the MOFs such as crystallinity, microstructure, reusability and surface area remain to be preserved after being 3D printed in both cases.