One of the major challenges in the field of organic semiconductors is to develop molecular design rules and processing routes which optimise the charge carrier mobility, whilst independently controlling the radiative and non-radiative processes. To date there has existed a seeming trade-off between charge carrier mobility and photoluminescence efficiency, which limits the development of some devices such as electrically pumped laser diodes. This thesis investigates fluorescence enhancement strategies for high-mobility polymer semiconductor systems and the mechanisms by which they currently display poor emission properties. Four independent approaches were taken and are detailed as follows. 1. Solubilising chain engineering It is shown that for the high mobility polymer poly(indacenodithiophene-co-benzothiadiazole), the addition of a phenyl- initiated side chain can enhance the solid-state fluorescence quantum yield, exciton lifetime and exciton diffusion length significantly in comparison to that without phenyl-addition. 2. Energy transfer to a highly fluorescent chromophore It is shown that for the high mobility polymer poly(indacenodithiophene-co-benzothiadiazole) efficient energy transfer to a more emissive squaraine dye molecule is possible despite fast non-radiative decay short exciton diffusion lengths. This results in a significant fluorescence enhancement, which in turn facilitates an order of magnitude increase of the efficiency of polymer light emitting diodes made from this material combination. 3. Energy gap engineering The well known Energy Gap Law predicts an increase in the non-radiative rate as the optical bandgap of an organic chromophore decreases in energy. In combination with this, almost all polymer semiconductors reported to date with high charge carrier mobility have low optical bandgaps. Therefore, molecular design principles which act to increase the optical bandgap of polymer semiconductors whilst retaining a high mobility were sought out. One specific system was successfully identified and showed a significant fluorescence enhancement compared to is predecessor poly(indacenodithiophene-co-benzothiadiazole) in both the solution and the solid state. It is found that the Frenkel exciton lifetime in this new system is a factor of four larger which also results in a significantly increased exciton diffusion length. An inter-chain electronic state is also identified and discussed. 4. Hydrogen substitution For some low-bandgap material systems such as erbium chromophores, high energy vibrational modes such as the C-H stretching mode can act as non-radiative pathways. The effect of hydrogen substitution with deuterium and fluorine was therefore investigated in a series of polythiophene derivative families. It was found that in the solid state, fluorescence and exciton lifetime enhancement occurred when the backbone hydrogen atoms were replaced with fluorine. However, evidence is given that this was not owing to the initial hypothesis, and is more likely owing to structural differences which occur in these substituted material systems.

<p>Over the last few decades, bulk-heterojunction organic photovoltaic devices comprising an intimately mixed donor-acceptor blend have gained serious attention due to their potential for being cheap, light weight, flexible and environmentally friendly. In this thesis, APFO-3/PCBM bulk-heterojunction based organic photovoltaic devices with an inverted layer sequence were investigated systematically. Doctor blade coating is a technique that is roll-to-roll compatible and cost efficient and has been used to fabricate the solar cells.</p><p>Initial studies focused on optimization of the electrodes. A thin film of the conductive polymer PEDOT:PSS was chosen to be the transparent anode. Different PEDOT:PSS films with respect to the film thickness and deposition temperature were characterized in terms of conductivity and transmission. Decent conductance and transmittance were obtained in the films deposited with wet film thickness setting of 35 μm, The cathode was fabricated from a metal bilayer comprising Al and Ti with an area about 1 cm², and the best-working cathodes contained a 70 nm thick Al layer covered by a thin Ti layer of about 10 -15 nm.</p><p>Optimized coating temperature and wet film thickness settings for the active layer and PEDOT:PSS layer were experimentally determined. The highest efficiency of the APFO-3/PCBM based inverted solar cells fabricated by doctor blading was 0.69%, which exceeded the efficiency of spin-coated inverted cells.</p><p>A higher efficiency (0.8 %) was achieved by adding a small amount of high molecular weight polystyrene to the active layer. Morphological changes after adding of the polystyrene were observed by optical microscopy and AFM. A coating temperature dependent phase separation of the APFO-3/PCBM/polystyrene blend was found.</p><p> </p>

<p>In this thesis, the microstructure of organic photovoltaic APFO-3:PC₆₁BM bulk-heterojunction blends was examined. Earlier studies have focused on the microstructure after spin coating. This thesis aims to give a better insight into microstructural degradation as the films are annealed above the glass transition temperature, T_g, and the mixture approaches thermodynamic equilibrium. Electro- and photoluminescence studies indicate that the polymer and PC₆₁BM are intermixed on a scale shorter than the exciton diffusion length of 10 nm, even when annealed above T_g. The temperature stability of APFO-3:PC₆₁BM was also investigated with respect to the molecular weight of the polymer. The photovoltaic performance of these blends was found to be stable up to temperatures approaching the glass transition temperature, especially if a high molecular-weight APFO-3 grade was used.</p><p> </p><p>The crystallization of PC₆₁BM was also investigated. Above T_g, PC₆₁BM crystallization was found to commence, albeit slowly at temperatures close to T_g. At elevated temperatures instead, micrometer sized crystals were observed to form. It was also noted that illumination while annealing APFO-3:PC₆₁BM thin films above T_g affected PC₆₁BM crystallization, the origin of which is so far unclear although chemical degradation could be largely excluded.</p>

In this thesis, the microstructure of organic photovoltaic APFO-3:PC61BM bulk-heterojunction blends was examined. Earlier studies have focused on the microstructure after spin coating. This thesis aims to give a better insight into microstructural degradation as the films are annealed above the glass transition temperature, Tg, and the mixture approaches thermodynamic equilibrium. Electro- and photoluminescence studies indicate that the polymer and PC61BM are intermixed on a scale shorter than the exciton diffusion length of 10 nm, even when annealed above Tg. The temperature stability of APFO-3:PC61BM was also investigated with respect to the molecular weight of the polymer. The photovoltaic performance of these blends was found to be stable up to temperatures approaching the glass transition temperature, especially if a high molecular-weight APFO-3 grade was used.   The crystallization of PC61BM was also investigated. Above Tg, PC61BM crystallization was found to commence, albeit slowly at temperatures close to Tg. At elevated temperatures instead, micrometer sized crystals were observed to form. It was also noted that illumination while annealing APFO-3:PC61BM thin films above Tg affected PC61BM crystallization, the origin of which is so far unclear although chemical degradation could be largely excluded.

Over the last few decades, bulk-heterojunction organic photovoltaic devices comprising an intimately mixed donor-acceptor blend have gained serious attention due to their potential for being cheap, light weight, flexible and environmentally friendly. In this thesis, APFO-3/PCBM bulk-heterojunction based organic photovoltaic devices with an inverted layer sequence were investigated systematically. Doctor blade coating is a technique that is roll-to-roll compatible and cost efficient and has been used to fabricate the solar cells. Initial studies focused on optimization of the electrodes. A thin film of the conductive polymer PEDOT:PSS was chosen to be the transparent anode. Different PEDOT:PSS films with respect to the film thickness and deposition temperature were characterized in terms of conductivity and transmission. Decent conductance and transmittance were obtained in the films deposited with wet film thickness setting of 35 μm, The cathode was fabricated from a metal bilayer comprising Al and Ti with an area about 1 cm2, and the best-working cathodes contained a 70 nm thick Al layer covered by a thin Ti layer of about 10 -15 nm. Optimized coating temperature and wet film thickness settings for the active layer and PEDOT:PSS layer were experimentally determined. The highest efficiency of the APFO-3/PCBM based inverted solar cells fabricated by doctor blading was 0.69%, which exceeded the efficiency of spin-coated inverted cells. A higher efficiency (0.8 %) was achieved by adding a small amount of high molecular weight polystyrene to the active layer. Morphological changes after adding of the polystyrene were observed by optical microscopy and AFM. A coating temperature dependent phase separation of the APFO-3/PCBM/polystyrene blend was found.

For more than 20 years, scientists have studied solar cells made from organic semiconductors. Throughout this time, device structures have evolved from bilayer devices to bulk heterojunction (BHJ) devices and even though efficiencies are approaching 10%, scientists still know relatively little about the transport of charge carriers and recombination mechanisms in these materials. Novel structures, based on lateral BHJ solar cells, have proven to be versatile tools to study transport and recombination mechanisms. In addition, these structures can easily be employed by researchers and solar cell manufacturers to determine the quality and measure the improvement of their materials. For these studies, poly(3-hexylthiophene) (P3HT):[6,6]-phenyl C61-butyric acid methyl ester (PCBM) has been employed due to its wide use among researchers as well as potential for commercialization. DC photocurrent measurements as a function of device length have yielded the mobility-lifetime product and the generation rate of free carriers within these BHJ devices. In addition to these parameters, the recombination rate as a function of light intensity provides information about the mechanisms of recombination. For example, by measuring the recombination rate as a function of applied electric field and light intensity we have found that recombination is unimolecular in nature and shifts to bimolecular at increased electric field strengths. Additionally, the mobility-lifetime product, generation rate, and recombination mechanism have been studied as a function of applied electric field, illumination spectrum, illumination intensity, etc. This information has provided much insight on physics of the P3HT:PCBM material system which did not exist before these studies. / text

The increasing demand for energy and the pressure to reduce reliance on fossil fuels encourages the development of devices to harness clean and renewable energy. Solar energy is a large enough source to fulfill these demands, however, in order to overcome its daily and seasonal variability, it has been proposed that sunlight be harvested and stored in the form of chemical fuels. One potential approach is the photosynthetic splitting of water to store solar energy in the simplest chemical bond, H–H, using a device that includes: semiconducting microwire arrays as light harvesting components, redox catalysts, and a membrane barrier for separating the products of water redox reactions.. However, the harvested solar energy can be lost across the system and it is critical to characterize the electrical properties of each component within the system to quantify how much of this energy will ultimately be coupled to the water splitting reactions. The aim of this research is to develop approaches for characterization of a proposed system of this kind, incorporating individual semiconductor microwires as photoelectrodes (with no redox catalysts) embedded into a candidate conducting polymer membrane to form a single functional unit. Semiconductor microwires were isolated and using a novel contact formation approach with tungsten probes in a standard probe station, and their current versus voltage properties were characterized. This approach is of particular interest when ii considering the limitations of conventional contact formation approaches (e.g. thermal evaporation of contact metals), arising from the small dimensions of the microwires and also the incompatibility of these techniques with many microwire/polymer structures due to the unwanted interactions between polymers, photoresists, etchants and the high temperature lithographic processes. The electrical properties of different microwires and also the junctions between microwires and two candidate polymers were studied. Specifically, the combination of methyl-terminated silicon microwires and PEDOT:PSS:Nafion demonstrated promising behavior, with a total DC resistance of approximately 720 kΩ (i.e. losses < 16 mV at maximum available photocurrent), making it a suitable candidate for the use in the proposed system. The outcome of these research may be applied to many applications including semiconducting microstructures and conducting polymers.

A new class of electrodes with nanometer-scale contact spacing can be produced at the edge of patterned metal/insulator/metal this film structures. A key challenge is to produce insulator layers with low leakage current and have pristine metal contacts for controlled molecular contacts. Atomic layer deposition of high quality Al2O3 thin films onto Au electrodes was enabled by surface modification with a self-assembled monolayer of -OH groups that react with a monolayer of trimethylaluminum gas source. Ar ion milling was then used to expose the edge of the Au/dielectric/Au structure for molecular electrode contacts. The junctions are characterized by atomic force microscope and tunnel current properties. The Au/self-assembled monolayer/Al2O3/Au tunnel junction, with a very thin oxide insulator layer (15.4 Å), is stable and has a small tunneling current density of about 0.20 ~ 0.75 A/cm2 at 0.5 V. Organometalic cluster molecules were attached to bridge the electrodes. Through tunnel current modeling, low temperature and photo current measurements, molecular current was found to be consistent with direct tunneling through the organic tethers to available states at the metal center. This novel electrode was also used to study the efficiency of organic conducting thin films where the photovoltaic efficiency can be improved when the electrode separation distance is below the exciton diffusion length. Copper (II) phthalocyanine (CuPc) was thermally evaporated between the nano-gap electrodes formed by Au/Al2O3/Au tunnel junctions. A large photocurrent enhancement over 50 times that of bulk CuPc film was observed when the electrode gap distance approached 10 nm. CuPc diffusion length is seen to be 10 nm consistent with literature reports. All devices show diode I-V properties due to a large Schottky barrier contact resistance between the small top Au electrode and the CuPc film. To add another dimension of nm-scale patterning, nanowires can be used as line-of-sight shadowmasks provided that nanowire location and diameter can be controlled. Lateral ZnO nanowires were selectively grown from the edge of a Si/Al2O3/Si multi-layer structure for potential integration into devices utilizing Si processing technology. Microstructural studies demonstrate a 2-step growth process in which the tip region, with a diameter ~ 10 nm, rapidly grew from the Al2O3 surface. Later a base growth with a diameter ~ 22 nm overgrew the existing narrow ZnO nanowire halting further tip growth. Kinetics studies showed surface diffusion on the alumina seed surface determined ZnO nanowire growth rate.

Organische Halbleiter besitzen neue, bemerkenswerte Materialeigenschaften, die sie für die grundlegende Forschung wie auch aktuelle technologische Entwicklung (bsw. org. Leuchtdioden, org. Solarzellen) interessant werden lassen. Aufgrund der starken konformative Freiheit der konjugierten Polymerketten führt die Vielzahl der möglichen Anordnungen und die schwache intermolekulare Wechselwirkung für gewöhnlich zu geringer struktureller Ordnung im Festkörper. Die Morphologie hat gleichzeitig direkten Einfluss auf die elektronische Struktur der organischen Halbleiter, welches sich meistens in einer deutlichen Reduktion der Ladungsträgerbeweglichkeit gegenüber den anorganischen Verwandten zeigt. So stellt die Beweglichkeit der Ladungen im Halbleiter einen der limitierenden Faktoren für die Leistungsfähigkeit bzw. den Wirkungsgrad von funktionellen organischen Bauteilen dar. Im Jahr 2009 wurde ein neues auf Naphthalindiimid und Bithiophen basierendes Dornor/Akzeptor Copolymer vorgestellt [P(NDI2OD‑T2)], welches sich durch seine außergewöhnlich hohe Ladungsträgermobilität auszeichnet. In dieser Arbeit wird die Ladungsträgermobilität in P(NDI2OD‑T2) bestimmt, und der Transport durch eine geringe energetischer Unordnung charakterisiert. Obwohl dieses Material zunächst als amorph beschrieben wurde zeigt eine detaillierte Analyse der optischen Eigenschaften von P(NDI2OD‑T2), dass bereits in Lösung geordnete Vorstufen supramolekularer Strukturen (Aggregate) existieren. Quantenchemische Berechnungen belegen die beobachteten spektralen Änderungen. Mithilfe der NMR-Spektroskopie kann die Bildung der Aggregate unabhängig von optischer Spektroskopie bestätigt werden. Die Analytische Ultrazentrifugation an P(NDI2OD‑T2) Lösungen legt nahe, dass sich die Aggregation innerhalb der einzelnen Ketten unter Reduktion des hydrodynamischen Radius vollzieht. Die Ausbildung supramolekularen Strukturen nimmt auch eine signifikante Rolle bei der Filmbildung ein und verhindert gleichzeitig die Herstellung amorpher P(NDI2OD‑T2) Filme. Durch chemische Modifikation der P(NDI2OD‑T2)-Kette und verschiedener Prozessierungs-Methoden wurde eine Änderung des Kristallinitätsgrades und gleichzeitig der Orientierung der kristallinen Domänen erreicht und mittels Röntgenbeugung quantifiziert. In hochauflösenden Elektronenmikroskopie-Messungen werden die Netzebenen und deren Einbettung in die semikristallinen Strukturen direkt abgebildet. Aus der Kombination der verschiedenen Methoden erschließt sich ein Gesamtbild der Nah- und Fernordnung in P(NDI2OD‑T2). Über die Messung der Elektronenmobilität dieser Schichten wird die Anisotropie des Ladungstransports in den kristallographischen Raumrichtungen von P(NDI2OD‑T2) charakterisiert und die Bedeutung der intramolekularen Wechselwirkung für effizienten Ladungstransport herausgearbeitet. Gleichzeitig wird deutlich, wie die Verwendung von größeren und planaren funktionellen Gruppen zu höheren Ladungsträgermobilitäten führt, welche im Vergleich zu klassischen semikristallinen Polymeren weniger sensitiv auf die strukturelle Unordnung im Film sind. / Organic semiconductors are in the focus of recent research and technological development (eg. for organic light-emitting diodes and solar cells) due to their specific and outstanding material properties. The strong conformational freedom of conjugated polymer chains usually leads to a large number of possible geometric arrangements while weak intermolecular interactions additionally lead to poor structural order in the solid state. At the same time the morphology of those systems has direct influence on the electronic structure of the organic semiconductor which is accompanied by a significant reduction of the charge carrier mobility in contrast to their inorganic counterparts. In that way the transport of charges within the semiconductor represents one of the main limiting factors regarding the performance and efficiency of functional organic devices. In 2009 Facchetti and coworkers presented a novel conjugated donor/acceptor copolymer based on naphthalene diimide and bithiophene [P(NDI2OD‑T2)] which was characterized by an outstanding charge carrier mobility. In this work the mobility of electrons and holes in the bulk of P(NDI2OD‑T2) is determined by single carrier devices and the time-of-flight technique. The results imply a low energetic disorder in these polymer layers. While the material was initially expected to be mainly amorphous, a detailed study of the photophysical properties of P(NDI2OD‑T2) shows that precursors of supramolecular assemblies (aggregates) are already formed in polymer solution. Quantum-chemical calculations support the occurring optical changes. NMR spectroscopy was applied to independently prove the formation of chain aggregates in commonly used organic solvents. The investigation of P(NDI2OD‑T2) solutions by analytical ultracentrifugation implies that aggregation mainly proceeds within single polymer chains by reduction of the hydrodynamic radius. To understand the influence of the chemical structure, pre-aggregation and crystal packing of conventional regioregular P(NDI2OD-T2) on the charge transport, the corresponding regioirregular polymer RI-P(NDI2OD-T2) was synthesized. By combining optical, X-ray, and transmission electron microscopy data, a quantitatively characterization of the aggregation, crystallization, and backbone orientation of all of the polymer films was possible, which was then correlated to the electron mobilities in electron-only diodes. The anisotropy of the charge transport along the different crystallographic directions is demonstrated and how the mobility depends on π-stacking but is insensitive to the degree or coherence of lamellar stacking. The comparison between the regioregular and regioirregular polymers also shows how the use of large planar functional groups leads to improved charge transport, with mobilities that are less affected by chemical and structural disorder with respect to classic semicrystalline polymers such as poly(3-hexylthiophene).

Polyaromatic molecules functionalized with carboxylic groups have served as model systems for the growth of organic semiconducting films on a large variety of substrates. Most non-reactive substrates allow for a growth mode compatible with the bulk phase of the molecular crystal with two molecules in the unit cell, but some more reactive substrates including Ag(111) and Ag(110) can induce substantial changes in the first monolayer (ML). In the specific case of Ag(110), the adsorbate unit cell of both NTCDA and PTCDA resembles a brickwall structure, with a single molecule in the unit cell. From this finding, it can be concluded that the adsorbate-substrate interaction is stronger than typical inter-molecular binding energies in the respective bulk phases. In the present work, the interactions between small Ag(110) clusters and a single NTCDA or PTCDA molecule are investigated with different ab initio techniques. Four major ingredients contribute to the binding between adsorbate and substrate: Directional bonds between Ag atoms in the topmost layer and the oxygen atoms of the molecule, Pauli repulsion between filled orbitals of molecule and substrate, an attractive van-der-Waals interaction, and a negative net charge on the molecule inducing positive image charges in the substrate, resulting therefore in an attractive Coulomb interaction between these opposite charges. As both Hartree-Fock theory and density functional theory with typical gradient-corrected density functional do not contain any long range correlation energy required for dispersion interactions, we compare these approaches with the fastest numerical technique where the leading term of the van-der-Waals interaction is included, i.e. second order Møller-Plesset theory (MP2). Both Hartree-Fock and density functional theories result in bended optimized geometries where the adsorbate is interacting mainly via the oxygen atoms, with the core of the molecule repelled from the substrate. Only at the MP2 level, the inclusion of the major part of the attractive van-der-Waals interaction brings the adsorbate back to an arrangement close to parallel to the substrate, with very small differences in height between the different subunits. With respect to experimental data obtained on Ag(111), the calculated distance between adsorbate and substrate is somewhat smaller, indicating that the open Ag(110) surface interacts more strongly with the organic compounds. This is consistent with the fact that only Ag(110) induces a brickwall unit cell of the adsorbate, a clear sign for a particularly large adsorption energy. The resulting model geometries are analysed in terms of cohesive energy, Mulliken charges, core level shifts, and vibrational properties. / Polyaromatische Moleküle, die mit Carboxylgruppen funktionalisiert wurden, haben als Modellsysteme für das Wachstum von organischen Halbleiterfilmen für eine breite Palette von Substraten gedient. Für die meisten nichtreaktiven Substrate ist ein zum molekularen Kristall kompatibles Wachstum mit zwei Monolagen pro Einheitszelle möglich, jedoch erzeugen reaktivere Substrate wie z.B. Ag(111) oder Ag(110) bereits substanzielle Modifikationen in der ersten Monolage. Im speziellen Fall von Ag(110) bildet die Adsorbateinheitszelle sowohl von NTCDA als auch PTCDA eine sogenannte brickwall structure heraus mit einem einzigen Molekül pro Einheitszelle. Aus dieser Beobachtung kann geschlussfolgert werden, dass die Adsorbat-Substrat-Wechselwirkung stärker ist als die typischen intermolekularen Bindungsenergien in der entsprechenden Bulk-Phase. In der vorliegenden Arbeit werden die Wechselwirkungen zwischen kleinen Ag(110)-Clustern und einem einzelnen NCTDA oder PTCDA-Molekül mit verschiedenen ab initio-Techniken untersucht. Im Wesentlichen tragen vier Hauptbestandteile zur Bindung zwischen Adsorbat und Substrat bei: Gerichtete Bindungen zwischen Ag-Atomen in der obersten Substratschicht und den Sauerstoffatomen des Moleküls, Pauli-Abstoßung zwischen besetzten Orbitalen von Molekül und Substrat, eine anziehende Van-der-Waals-Wechselwirkung sowie einer negativen Ladung des Moleküls und der dazugehörigen positiven Spiegelladung im Substrat, die zu einer anziehenden Coulombwechselwirkung führen. Da weder die Hartree-Fock-Theorie noch die Dichtefunktionaltheorie mit dem typischen gradientenkorrigierten Dichtefunktional die für Dispersionswechselwirkungen benötigte langreichweitige Korrelationsenergie beinhalten, vergleichen wir diese beiden Ansätze mit der schnellsten numerischen Methode, die den dominierenden Term der Van-der-Waals-Wechselwirkung beinhaltet, nämlich der Møller-Plesset-Theorie zweiter Ordnung (MP2). Sowohl die Hartree-Fock-Theorie als auch die Dichtefunktionaltheorie sagen verbogene optimierte Geometrien voraus, die vorwiegend durch die Sauerstoffatome interagieren, wohingegen die zentralen Teile des Moleküls vom Substrat abgestoßen werden. Lediglich die MP2, die den wesentlichen Teil der anziehenden Van-der-Waals-Wechselwirkung beinhaltet, sagt eine beinahe parallele Anordnung des Moleküls an das Substrat voraus, wobei die einzelnen Untereinheiten des Moleküls nur unwesentlich verschiedene Abstände zum Substrat haben. Im Vergleich zu experimentellen Daten für Ag(111) ist die berechnete Distanz zwischen Adsorbat und Substrat etwas kleiner, woraus sich schlussfolgern lässt, dass die offene Ag(110)-Oberfläche stärker mit den organischen Verbindungen interagiert. Das ist im Einklang mit der Tatsache, dass nur Ag(110) die brickwall-Struktur des Adsorbats besitzt, was ein deutliches Zeichen für eine hohe Adsorptionsenergie ist. Die resultierenden Modellgeometrien wurden bezüglich ihrer Kohäsionsenergie, Mullikenladungen, Kernelektronenniveauverschiebungen und vibrationeller Eigenschaften untersucht.