221 |
Indoor and Outdoor Evaluation of Campus RSS PerformanceLi, Qian, Zhang, Xintong January 2011 (has links)
The focus of this thesis work is to evaluate the RSS (Received Signal Strength) Performance of the University of Gävle (HiG) based on IEEE 802.11 standards both indoor and outdoor. Authors investigated the issues of deploying access points for wireless local area networks in the library-2nd floor, building 99-4th floor and outdoor university campus. By using the program VisiWave Site Survey, Global Position System (GPS) and RSS sensor to analysis the received signal strength, throughput and radio map. The influence of the building material and distance for the signal strength and the throughput are done by investigating indoor environment. The results of investigation suggest that most parts of library-2nd floor and building 99-4th floor possess at least a good RSS performance. However, minority parts of these places have a poor RSS performance, and the new resolution of Access Points’ (AP) deployment for these poor-RSS-performance parts is provided. For the outdoor campus part, the RSS in the area which near the walls of building is satisfactory (Received Signal Strength Indication (RSSI) between -79.8 dBm and -57 dBm), however in the centre of outdoor campus the RSS is poor. Thus, the evaluation of APs deployment in HiG is achieved.
|
222 |
Physical layer interface for IEEE 802.11 MAC / Hårdvaruinterface för IEEE 802.11 MACNorén, Per January 2002 (has links)
There are several standards for wireless communication. People that are involved in computers and networking recognize names like Bluetooth, HiperLAN and IEEE 802.11. A fundamental part of an IEEE 802.11 node is the Medium Access Controller. It establishes and controls communication with other nodes, using a physical layer unit. This is the work that was carried out as a master thesis project at Ericsson Microelectronics. The main goal was to design, implement and evaluate a hardware interface between the MAC and the physical layer. An important part of the work was to find a suitable partition scheme for hardware and software and to achieve this, an investigation of processor-cycles usage was carried out to support design decisions. The hardware/software partition resulted in hardware-functionality for decode of received frames and automatic transmission of acknowledge frames.
|
223 |
Investigation of IEEE Standard 802.11 Medium Access Control (MAC) Layer in ad-hocGarcia Torre, Fernando January 2006 (has links)
This thesis involved a research of mechanisms of MAC layer in the ad-hoc networks environment, the ad-hoc networks in the terminology of the standard are called IBSS Independent Basic Service, these type of networks are very useful in real situation where there are not the possibility of display a infrastructure, when there isn’t a network previous planning. The connection to a new network is one of the different with the most common type of Wireless Local Area Networks (WLAN) that are the ones with infrastructure. The connection is established without the presence of a central station, instead the stations discover the others with broadcast messages in the coverage area of each station. In the context of standard 802.11 networks the communication between the stations is peer to peer, only with one hop. To continue with initiation process is necessary the synchronization between the different stations of his timers. The other capital mechanism that is treated is the medium access mechanism, to hold a shared and unreliable medium, all the heavy of this issue goes to the distributed coordination function DCF. In this moment there is an emergent technology, WIMAX or standard IEEE 802.16, like the standard 802.11 is a wireless communication protocol. Some comparison between the MAC layer mechanisms would be realized between these two standards
|
224 |
Achieving Fairness in 802.11-Based Multi-channel Wireless Mesh NetworksLee, Ann January 2006 (has links)
Multi-hop wireless networks based on 802. 11 are being used more widely as an alternative technology for last-mile broadband Internet access. Their benefits include ease of deployment and lower cost. Such networks are not without problems. Current research on such networks aims at a number of challenges, including overcoming capacity limitation and poor fairness. <br /><br /> The focus of our research is for achieving fairness in multi-channel multi-hop wireless networks. First, we review the literature for different methods for representing link-contention areas, and the existing single-channel fairness computational model. Second, we generalize the fairness constraints applied to each link-contention area, defined in the existing single-channel fairness reference model, to multi-channel models. Third, by adopting the concepts of link-usage matrix and medium-usage matrix to represent network topology and flow status, and using Collision Domain theory and Clique Graph theory to represent link-contention area, we develop a computational model to compute optimal MAC-layer bandwidth allocated to each flow in a multi-channel multi-hop WMN. We simulate various network configurations to evaluate the performance of the fairness algorithm based on the above computational model in different scenarios. We have found that in the multi-channel environment, our extension to the Collision Domain model generally provides a more accurate estimation of network capacity. Based on this model, we have extended the source-rate-limiting mechanism, which limits the flow rate to its fair share computed by the computational model. Experimental results that validate these findings are presented in this thesis.
|
225 |
Network-Layer Resource Allocation for Wireless Ad Hoc NetworksAbdrabou, Atef January 2008 (has links)
This thesis contributes toward the design of a quality-of-service (QoS) aware network layer for wireless ad hoc networks. With the lack of an infrastructure in ad hoc networks, the role of the network layer is not only to perform multihop routing between a source node and a destination node, but also to establish an end-to-end connection between communicating peers that satisfies the service level requirements of multimedia applications running on those peers.
Wireless ad hoc networks represent autonomous distributed systems that are infrastructure-less, fully distributed, and multi-hop in nature. Over the last few years, wireless ad hoc networks have attracted significant attention from researchers. This has been fueled by recent technological advances in the development of multifunction and low-cost wireless communication gadgets. Wireless ad hoc networks have diverse applications spanning several domains, including military, commercial, medical, and home networks. Projections indicate that these self-organizing wireless ad hoc networks will eventually become the dominant form of the architecture of telecommunications networks in the near future. Recently, due to increasing popularity of multimedia applications, QoS support in wireless ad hoc networks has become an important yet challenging objective. The challenge lies in the need to support the heterogeneous QoS requirements (e.g., data rate, packet loss probability, and delay constraints) for multimedia applications and, at the same time, to achieve efficient radio resource utilization, taking into account user mobility and dynamics of multimedia traffic.
In terms of research contributions, we first present a position-based QoS routing framework for wireless ad-hoc networks. The scheme provides QoS guarantee in terms of packet loss ratio and average end-to-end delay (or throughput) to ad hoc networks loaded with constant rate traffic. Via cross-layer design, we apply call admission control and temporary bandwidth reservation on discovered routes, taking into consideration the physical layer multi-rate capability and the medium access control (MAC) interactions such as simultaneous transmission and self interference from route members.
Next, we address the network-layer resource allocation where a single-hop ad hoc network is loaded with random traffic. As a starting point, we study the behavior of the service process of the widely deployed IEEE 802.11 DCF MAC when the network is under different traffic load conditions. Our study investigates the near-memoryless behavior of the service time for IEEE 802.11 saturated single-hop ad hoc networks. We show that the number of packets successfully transmitted by any node over a time interval follows a general distribution, which is close to a Poisson distribution with an upper bounded distribution distance. We also show that the service time distribution can be approximated by the geometric distribution and illustrate that a simplified queuing system can be used efficiently as a resource allocation tool for single hop IEEE 802.11 ad hoc networks near saturation.
After that, we shift our focus to providing probabilistic packet delay guarantee to multimedia users in non-saturated IEEE 802.11 single hop ad hoc networks. We propose a novel stochastic link-layer channel model to characterize the variations of the IEEE 802.11 channel service process. We use the model to calculate the effective capacity of the IEEE 802.11 channel. The channel effective capacity concept is the dual of the effective bandwidth theory. Our approach offers a tool for distributed statistical resource allocation in single hop ad hoc networks, which combines both efficient resource utilization and QoS provisioning to a certain probabilistic limit.
Finally, we propose a statistical QoS routing scheme for multihop IEEE 802.11 ad hoc networks. Unlike most of QoS routing schemes in literature, the proposed scheme provides stochastic end-to-end delay guarantee, instead of average delay guarantee, to delay-sensitive bursty traffic sources. Via a cross-layer design approach, the scheme selects the routes based on a geographical on-demand ad hoc routing protocol and checks the availability of network resources by using traffic source and link-layer channel models, incorporating the IEEE 802.11 characteristics and interaction. Our scheme extends the well developed effective bandwidth theory and its dual effective capacity concept to multihop IEEE 802.11 ad hoc networks in order to achieve an efficient utilization of the shared radio channel while satisfying the end-to-end delay bound.
|
226 |
Centralized Rate Allocation and Control in 802.11-based Wireless Mesh NetworksJamshaid, Kamran January 2010 (has links)
Wireless Mesh Networks (WMNs) built with commodity 802.11 radios are a cost-effective means of providing last mile broadband Internet access. Their multihop architecture allows for rapid deployment and organic growth of these networks.
802.11 radios are an important building block in WMNs. These low cost radios are readily available, and can be used globally in license-exempt frequency bands. However, the 802.11 Distributed Coordination Function (DCF) medium access mechanism does not scale well in large multihop networks. This produces suboptimal behavior in many transport protocols, including TCP, the dominant transport protocol in the Internet. In particular, cross-layer interaction between DCF and TCP results in flow level unfairness, including starvation, with backlogged traffic sources. Solutions found in the literature propose distributed source rate control algorithms to alleviate this problem. However, this requires MAC-layer or transport-layer changes on all mesh routers. This is often infeasible in practical deployments.
In wireline networks, router-assisted rate control techniques have been proposed for use alongside end-to-end mechanisms. We evaluate the feasibility of establishing similar centralized control via gateway mesh routers in WMNs. We find that commonly used router-assisted flow control schemes designed for wired networks fail in WMNs. This is because they assume that: (1) links can be scheduled independently, and (2) router queue buildups are sufficient for detecting congestion. These abstractions do not hold in a wireless network, rendering wired scheduling algorithms such as Fair Queueing (and its variants) and Active Queue Management (AQM) techniques ineffective as a gateway-enforceable solution in a WMN. We show that only non-work-conserving rate-based scheduling can effectively enforce rate allocation via a single centralized traffic-aggregation point.
In this context we propose, design, and evaluate a framework of centralized, measurement-based, feedback-driven mechanisms that can enforce a rate allocation policy objective for adaptive traffic streams in a WMN. In this dissertation we focus on fair rate allocation requirements. Our approach does not require any changes to individual mesh routers. Further, it uses existing data traffic as capacity probes, thus incurring a zero control traffic overhead. We propose two mechanisms based on this approach: aggregate rate control (ARC) and per-flow rate control (PFRC). ARC limits the aggregate capacity of a network to the sum of fair rates for a given set of flows. We show that the resulting rate allocation achieved by DCF is approximately max-min fair. PFRC allows us to exercise finer-grained control over the rate allocation process. We show how it can be used to achieve weighted flow rate fairness. We evaluate the performance of these mechanisms using simulations as well as implementation on a multihop wireless testbed. Our comparative analysis show that our mechanisms improve fairness indices by a factor of 2 to 3 when compared with networks without any rate limiting, and are approximately equivalent to results achieved with distributed source rate limiting mechanisms that require software modifications on all mesh routers.
|
227 |
Experimental Performance Evaluation of Bit-Rate Selection Algorithms in Multi-Vehicular NetworksSon, Giyeong 21 January 2011 (has links)
IEEE 802.11 PHY supports multiple transmission rates according to multiple different modulations and coding schemes. Each WiFi station selects its own transmission rate according to its own
algorithm; in particular, the IEEE 802.11 standards do not specify the bit-rate selection method. Although many adaptive bit-rate selection algorithms have been proposed, there is limited research
and evaluation on the performance of such algorithms for roadside networks, especially in cases with multi-vehicle roadside multi-vehicular WiFi networks.
In this thesis we propose an opportunistic highest bit-rate algorithm, Opportunistic Highest Bit-Rate Multi-Vehicular WiFi Networks (OHBR-MVN), specifically for roadside multi-vehicular WiFi networks. Our proposal is based on three key characteristics of such networks: (1) vehicles will drive closer to, and eventually pass, the roadside WiFi station, experiencing a progressively better
transmission environment; (2) the vast majority of data transmitted in single-vehicle drive-by downloading scenarios occurs at the maximum transmission rate; (3) vehicles that transmit at less than the maximum rate do so at the expense of those that could send more data at a higher
transmission rate. We therefore believe that transmitting only at the highest possible bit-rate is the preferred algorithm for such networks. Further, this approach keeps the bit-rate selection extremely simple, avoiding the complexity and resulting problems of adaptive approaches.
Through a series of experiments that compare the throughput of both fixed and adaptive bit-rate
selection algorithms we show that our approach yields both higher throughput and better fairness characteristics, while being significantly simple, and thus more robust.
|
228 |
Studies in Wireless Home Networking Including Coexistence of UWB and IEEE 802.11a SystemsFiroozbakhsh, Babak 25 January 2007 (has links)
Characteristics of wireless home and office services and the corresponding networking issues are discussed. Local Area Networking (LAN) and Personal Area Networking (PAN) technologies such as IEEE 802.11 and Ultra Wideband (UWB) are introduced. IEEE 802.11a and UWB systems are susceptible to interference from each other due to their overlapping frequencies. The major contribution of this work is to provide a framework for coexistence of the two systems. The interference between the two systems is evaluated theoretically by developing analytical models, and by simulations. It is shown that the interference from UWB on IEEE 802.11a systems is generally insignificant. IEEE 802.11a interference on UWB systems, however, is very critical and can significantly increase the bit error rate (BER) and degrade the throughput of the UWB system. A novel idea in the MAC layer is presented to mitigate this interference by means of temporal separation. Simulation results validate our technique. Implications to wireless home services such as high definition television (HDTV) are provided. Future research directions are discussed.
|
229 |
Correct, Efficient, and Realistic Wireless Network SimulationsSubbareddy, Dheeraj Reddy 10 January 2007 (has links)
Simulating wireless networks accurately is a non-trivial task because of the large
parameter space that affects the performance of such networks. Increasing the amount of
detail in the simulation model increases these requirements by many times. Hence there
is a need to develop suitable abstractions that maintain the accuracy of the simulation
while keeping the computational resource requirements low. The topic of wireless network
simulation models is explored in this research, concentrating on the medium access control
and the physical layers.
In the recent years, a large amount of research has focussed on various kinds of wireless
networks to fit various application domains. Mobile Ad-Hoc Networks (MANETs), Wire-
less Local Area Networks (WLANs), and Sensor Networks are a few examples.The IEEE
802.11 Physical layer(PHY) and Medium Access Control (MAC) layer are the most popular
wireless technologies in practice. Consequently, most implementations use the IEEE 802.11
specifications as the basis for higher layer protocol design and analyses.
In this dissertation, we explore the correctness, efficiency, and realism of wireless network
simulations. We concentrate on the 802.11-based wireless network simulations, although the
methods and results can also be used for various other wireless network simulations too.
While many simulators model the IEEE 802.11 wireless networks, almost all of them tend to
make some abstractions to lessen the computation burden and to obtain reasonable results.
A comparitive study of three wireless simulators is made with respect to the correctness of
their ideal behavior as well as their behavior under a high degree of load.
Further, the physical-layer abstraction in wireless network simulations tends to be very
simplistic because of the huge computational requirements that are needed to accurately
model the various propagation, fading, and shadowing models. When mobility is taken into
account several other issues like the Doppler effect should also be accounted for.
This dissertation explores an empirical way to model the physical layer which cumula-
tively accounts for all these effects. From a network protocol designers perspective, it is
the cumulative effect of all these parameters that is of interest.
Our major contribution has been the investigation of novel empirical models of the
wireless physical layer, which account for node mobility and other effects in an outdoor
environment. These models are relatively more realistic and efficient when implemented
in a simulation environment. Our simulation experiments validate the models and pro-
vide simulation results which closely match our outdoor experiments. Another significant
contribution is in understanding and design of wireless network simulation models.
|
230 |
Design of a Wireless LAN Medium Access Controller on the ARM-based PlatformYang, Cheng-Hsien 03 September 2003 (has links)
It is a future trend to include the function of wireless networking in portable electronic devices, such as notebooks, tablet PC, PDA, mobile phone, and other information applicants. IEEE 802.11 is the most popular wireless LAN protocol that defines the functions in the medium access control (MAC) layer and physical layer.
In this thesis, we design and implement a flexible and reusable soft IP (Intellectual Property) for wireless MAC that is compatible with AMBA system and can be used in SOC applications. The wireless MAC supports buffer descriptors, interrupt and DMA. The IP provides an AMBA-compatible interface for the host system bus, and provides a communication interface for the baseband processor in the physical layer.
|
Page generated in 0.0274 seconds