No description available.

AASHTO LRFD requires the use of longitudinal stiffeners in plate girder webs when the web slenderness D/tw is greater than 150. This practice is intended to limit the lateral flexing of the web plate during construction and at service conditions. AASHTO accounts for an increase in the web bend buckling resistance due to the presence of a longitudinal stiffener. However, when the theoretical bend buckling capacity of the stiffened web is exceeded under strength load conditions, the Specifications do not consider any contribution from the longitudinal stiffener to the girder resistance. That is, the AASHTO LRFD web bend buckling strength reduction factor Rb applied in these cases is based on an idealization of the web neglecting the longitudinal stiffener. This deficiency can have significant impact on girder resistance in regions of negative flexure. This research is aimed at evaluating the improvements that may be achieved by fully considering the contribution of web longitudinal stiffeners to the girder flexural resistance. Based on refined FE test simulations, this research establishes that minimum size longitudinal stiffeners, per current AASHTO LRFD requirements, contribute significantly to the post buckling flexural resistance of plate girders, and can bring as much as a 60% increase in the flexural strength of the girder. A simple cross-section Rb model is proposed that can be used to calculate the girder flexural resistance at the yield limit state. This model is developed based on test simulations of straight homogenous girders subjected to pure bending, and is tested extensively and validated for hybrid girders and other limit states. It is found that there is a substantial deviation between the AISC/AASHTO LTB resistance equations and common FE test simulations. Research is conducted to determine the appropriate parameters to use in FE test simulations. Recommended parameters are identified that provide a best fit to the mean of experimental data. Based on FE simulations on unstiffened girders using these recommended parameters, a modified LTB resistance equation is proposed. This equation, used in conjunction with the proposed Rb model also provides an improved handling of combined web buckling and LTB of longitudinally stiffened plate girders. It is observed that the noncompact web slenderness limit in the Specifications, which is an approximation based on nearly rigid edge conditions for the buckling of the web plate in flexure is optimistic for certain cross-sections with narrow flanges. This research establishes that the degree of restraint at the edges of the web depend largely on the relative areas of the adjoining flanges and the area of the web. An improved equation for the noncompact web slenderness limit is proposed which leads to a better understanding and representation of the behavior of these types of members.

Structural Reliability treats uncertainties in structural design systematically, evaluating the levels of safety and serviceability of structures. During the past decades, it has been established as a valuable design tool for the description of the performance of structures, and lately stands as a basis in the background of the most of the modern design standards, aiming to achieve a uniform behaviour within a class of structures. Several methods have been proposed for the estimation of structural reliability, both deterministic (FORM and SORM) and stochastic (Monte Carlo Simulation etc) in nature. Offshore structures should resist complicated and, in most cases, combined environmental phenomena of greatly uncertain magnitude (eg. wind, wave, current, operational loads etc). Failure mechanisms of structural systems and components are expressed through limit state functions, which distinguish a failure and a safe region of operation. For a jacket offshore structure, which comprises of multiple tubular members interconnected in a three dimensional truss configuration, the limit state function should link the actual load or load combination acting on it locally, to the response of each structural member. Cont/d.

Derrière tout acte il y a une sorte de « mise en scène », une « tentative d'exprimer » ce que l'auteur ne parvient à mettre en mots, à métaboliser, d'où le recours au primat de l'agir. Dans ce travail auprès d’Auteurs d’Infraction à Caractère Sexuel en intrafamilial, il est question de saisir, d'appréhender les conditions du passage à l'acte et ce que celles-ci ont pu engendrer au sein du psychisme du sujet, pour favoriser la transgression.À travers diverses notions tirées de la littérature analytique, notamment celles attenantes à la construction psychique, à la clinique du traumatisme ou encore de la transgénérationnalité, est mise en débat la question de l'influence de l’environnement sur le fait psychique individuel.Posant, de ce fait, l'hypothèse que les identifications et répétitions transgénérationnelles d’origines traumatiques peuvent être en jeu dans le passage à l'acte, en particulier chez les AICS en intrafamilial. Ce type de passage à l'acte pourrait-il alors représenter une résolution d'une dynamique familiale vécue comme « défaillante », voire traumatique, pour le sujet ? Dans une approche phénoménologique associée à une posture psychanalytique, sont déclinés sept accompagnements de patients nous permettant de répondre à ces interrogations. L'objectif étant de réaliser une étude clinique basée sur le vécu subjectif de chacun d’entre eux, afin de mettre en lumière ce qui pourrait faire défaut dans leur structuration, leurs investissements et rapports objectaux.Le voyage au travers des cas proposés permet de poser la question du caractère résolutif de ces passage à l’acte vis-à-vis d’une dynamique familiale, dans laquelle s’origine un vécu traumatique ? Par l’infraction sexuelle, perpétrée en intrafamilial, le sujet passe-t-il par le corps et l’objectalisation d’un autre familial pour crier sa souffrance, son « mal à être » ? Le passage à l’acte, chez ces Auteurs d’Infractions à Caractère Sexuel en intra-familial, est il résolutif d’une problématique identitaire traumatique, venant d’une nécessité de trouver un sens, une recherche de signifiance à l’existence même du sujet ? Via l'analyse des mécanismes de défenses, des représentations, ainsi que des positions transférentielles et contre-transférentielles mises en jeu, il s’agit de travailler la remise en sens, pour permettre à ces patients de développer leurs capacités d’élaboration, leur redonner une place, dans le respect de leur subjectivité et celle d’autrui, une place capable de supporter la construction identitaire originelle défaillante, retrouver une identité pour dépasser le traumatique, et ouvrir le chemin d’une reconstruction. / Behind every act there is a sort of "staging", an "attempt to express" what the author cannot put into words nor metabolize, which leads him to act. In this work, amoung Authors of Infringement of Sexual Character (AISC) within familial, the aim is to understand and apprehend the conditions that triggers the act and how they affected the subject's psyche, leading him to give into the transgression.Through notions taken from the analytic's literature, in particular notions linked to the psyche's construction, to traumatic clinic or even the transgenerational transmission, we debate on the question of the influence of the environment on the individual's psyche functionning. Thereby posing hypothesis that identifications and transgenerationals repeats of traumatic origin can contribute in triggering the act, even more for AISC within familial. Could this kind of acting out then represent the consequences of a family's dynamicity experienced as "failing", or even traumatic, by the subject? Using a phenomenologic approach associated with a psychoanalytic positioning, the thorough analysis of seven case-studies could help answer those questions. The objective is to create a clinic study based on the subjective experience of each of them. This is done in hope to bring forward what could lack in their structuring, in their objectals investments and relationships.This trip through the proposed cases allow the question of whether the resolvent nature of these acting out vis-à-vis a family's dynamicity in which a traumatic experience takes its roots? Through the sexual offence, perpetrated within the family, is the subject using the body and the objectisation of another family to shout out his suffering, his "ill-being"? Is the acting out, for Authors of Infringement of Sexual Character (AISC) within familial, a consequence of a traumatic identity crisis, the need to find a sense or the search to the meaning to the subject's own existence? Through the analysis of defense mechanisms, representations, transference and counter-transference positions put in place, the goal is to help rework the senses, allow those patients to develop their elaboration capability, to give them a place, with respect to their subjectivity and that of other, a place capable of sustaining the construction of their originally deficient identity, to rediscover an identity that surpasses the trauma, and open the gates of reconstruction.

Nowadays / design, fabrication and erection of steel structures can be taken place at different locations as a result of rapid globalization / owners may require the use of widely accepted steel design codes. Therefore, engineers are faced with the challenge of being competent with several design specifications for a particular material type. AISC-360 and EC3 are widely accepted steel structure design specifications that utilize limit state principles with some similarities and differences in application. Hereby a study has been undertaken to put together the nominal strength expressions presented in both AISC-360 and EC3 codes in a single document, to identify the similarities and the differences in calculated strengths and to facilitate rapid learning of either of the specifications with prior knowledge of the other. Because of the wide scope of specifications, only fundamental failure modes are considered in this thesis. Resistance equations are directly compared with each other wherever possible. For cases where the treatment of specifications is entirely different, representative members were considered for comparison purposes.

This study consists of three self-standing parts, each dealing with a different aspect of design of composite steel-concrete flexural members. The first part deals with a new type of shear connection in composite joists. Composite steel-concrete flexural members have increasingly become popular in design and construction of floor systems, structural frames, and bridges. A particularly popular system features composite trusses (joists) that can span large lengths and provide empty web space for installation of typical utility conduits. One of the prominent problems with respect to composite joists has been the installation of welded shear connection due to demanding welding requirements and the need for significant welding equipment at the job site. This part of the study presents a new type of shear connection developed at Virginia Tech— standoff screws. Results of experimental and analytical research are presented, as well as the development of a recommended design methodology. The second part deals with reliability of composite beams. Constant research advances in the field of composite steel-concrete beam design have resulted in numerous enhancements and changes to the American design practice, embodied in the composite construction provisions of the AISC Specification (AISC 1999). Results of a comprehensive reliability study of composite beams are presented. The study considers specification changes since the original reliability study by Galambos et al. (1976), considers a larger database of experimental data, and analyses recent proposals for changes in design of shear connection. Comparison of three different design methods is presented based on a study of 15,064 composite beam cases. A method to consider effect of degree of shear connection on strength reduction factor is proposed. Finally, while basic analysis theories between the two are similar, requirements for determining the strength of composite beams in Eurocode 4 (CEN 1992) and 1999 AISC Specification (AISC 1999) differ in many respects. This is particularly true when considering the design of shear connections. This part of the dissertation explores those differences through a comparative step-by-step discussion of major design aspects, and accompanying numerical example. Several shortcomings of 1999 AISC Specification are identified and adjustments proposed. / Ph. D.

<p>Composite Plate Shear Walls - Concrete Filled (C-PSW/CF), also known as SpeedCore walls, are increasingly used in commercial buildings. C-PSW/CF offer the advantages of modularization and expedited construction time. The performance of C-PSW/CF under wind and seismic loading has been extensively studied. As such, building codes permit the use of these walls in non-seismic and seismic regions. In addition to these lateral loads, C-PSW/CF may be exposed to fire loading during their service life. Elevated temperatures resulting from the fire loading subject structural components to a set of forces and deformations. These elevated temperatures result in the significant degradation of the material properties. Thus, fire loading may lead to the failure of structural components during fire incidents within the buildings.</p> <p>This dissertation describes (i) experimental, numerical, and analytical studies conducted to evaluate the performance of C-PSW/CF and (ii) the development of design guidelines for C-PSW/CF subjected to fire and gravity loading. The results from prior experimental investigations were compiled, and five additional fire tests were conducted to address gaps in the experimental data. The fire tests were conducted on laboratory-scale specimens subjected to axial compressive loading and simulated standard fire loading (heating). The parameters considered in the tests were axial compressive loading (21% – 30% of section compressive strength, <em>Ag f’c</em>), steel plate slenderness (24 – 48, tie spacing-to-steel plate thickness ratio), and uniformity of heating (all-sided versus three-sided heating).</p> <p>Numerical and analytical studies were conducted using two independent methods namely Finite Element (FE) and Finite Difference (FD) methods. The developed models were benchmarked to test data, and the benchmarked models were used to conduct parametric studies to expand the database. The thermal and structural material properties recommended by Eurocode standards were applied in these models. The parameters considered were the wall thickness (200 mm – 600 mm), wall slenderness (story height-to-concrete thickness ratio, <em>H/tc</em>= 5 – 25), axial load ratio (<em>Pu</em> ≤ 30% section concrete strength, <em>Ac f’c</em>), heating uniformity (uniform versus non-uniform heating), boundary conditions (pinned versus fixed), cross-sectional steel plate reinforcement ratio (<em>As/Ag</em> =1.3% – 5.3%), steel plate slenderness ratio (<em>stie/tp</em> = 20 – 75), tie bar spacing-to-wall concrete thickness ratio (<em>stie/tc</em> = 0.5 – 1.0), and concrete compressive strength (<em>f’c</em> = 40 MPa – 55 MPa).</p> <p>Symmetric nonlinear thermal gradients were developed through wall thickness for the walls exposed to uniform fire loading. Due to the low thermal conductivity of concrete, the temperature decreased nonlinearly through the wall thickness towards the mid-thickness of the walls. For the non-uniform fire exposure, temperatures through the wall thickness decreased nonlinearly towards the unexposed surface of the walls. A consistent trend was observed in the axial displacements of C-PSW/CF under combined fire and gravity loading. The observed trend consisted of several steps including (i) thermal expansion, (ii) gradual axial shortening, (iii) fast axial shortening, and (iv) failure.</p> <p>Local buckling of steel plates between tie bars was observed in all walls. However, this phenomenon did not cause any significant degradation in structural performance or failure of the walls. The results from parametric studies indicated that wall slenderness ratio (story height-to-wall thickness ratio), wall thickness, applied axial load ratio, and end boundary conditions have a significant influence on the fire resistance of C-PSW/CF. Higher wall slenderness ratios and load ratios had a detrimental effect on the fire resistance of walls. Global buckling was the dominant failure mode for the walls with high slenderness ratios (e.g., <em>H</em>/<em>tc </em>³ 15). In thicker walls, the lower temperatures in the middle regions of the concrete helped to maintain the axial compressive capacity of walls under fire loading. Limiting the steel plate slenderness ratio could slightly improve the fire resistance of unprotected walls by arresting the extent of local buckling between tie bars.</p> <p>The results from the parametric studies have been used to develop an approach for designing C-PSW/CF subjected to combined fire and gravity loading. The total (linear) length of the wall was discretized into unit width columns, where each unit width column corresponded to a length of wall equal to the tie bar spacing (<em>stie</em>). Thus, each unit is like a column with steel plates on two opposite surfaces, concrete infill, and tie bars distributed uniformly along the height. The axial load capacity of C-PSW/CF can be estimated as the axial load capacity of the unit width column, calculated using the developed approach, multiplied by the linear length of the wall divided by the unit width (tie bar spacing). For this approach, the wall slenderness ratio (<em>H/tw</em>), has a limiting value of 20. Walls with wall slenderness ratios greater than 20 should be fire protected. The expansion of the material on the exposed surface of walls generated moments through the wall cross-section in non-uniform fire scenarios. This phenomenon caused the early failure of walls (~40 minutes) with wall slenderness ratios greater than 20. An approach was developed to conservatively estimate the fire-resistance rating (in hours) of unprotected C-PSW/CF exposed to the standard fire time-temperature curve. The fire-resistance rating of C-PSW/CF depends directly on the applied axial load ratio, wall slenderness ratio, and wall thickness.</p> <p>The temperature profile through the wall thickness can be calculated by discretizing the section into fibers (or elements). Since the temperature of the elements is uniform along the height and length of walls, 1D thermal analysis (through wall thickness) can be performed using heat transfer equations or the fiber-based program developed in the study.</p> <p>Vent holes are recommended to relieve the buildup steam pressure as the moisture content of concrete evaporates at temperatures exceeding the boiling point of water. A rational method was developed to design the vent holes as a function of the maximum temperature and thermal gradient through the wall thickness, heating duration, moisture content, and the acceptable level of pressure buildup on the steel plates. However, in typical cases, unprotected C-PSW/CF walls can be provided with 25 mm diameter vent holes spaced at a distance equal to story height or 3.6 m (maximum) in the horizontal and vertical directions to relieve the buildup of steam or water vapor pressure.</p> <p>This research study also led to the development and validation of a computer program that can be used instead of the design equations to more accurately model and calculate the thermal and structural performance of composite C-PSW/CF. This program is based on a fiber-based section and member analysis method that can be used to evaluate the performance and axial (gravity) load capacity of unprotected and protected C-PSW/CF subjected to uniform or non-uniform heating. The analysis can be conducted by implementing standard (ISO 834 or ASTM E119), Eurocode parametric, or user input gas (or surface) time-temperature curves.</p> <p>The proposed equations and the recommendations in this study can be used to develop design guidelines and specifications for fire resistance design of C-PSW/CF under combined fire and gravity loading. A code change proposal will be proposed to AISC <em>Specification</em> - Appendix 4 (Structural Design for Fire Condition).</p>

<p dir="ltr">Composite Plate Shear Wall/ Concrete Filled (C-PSW/CF), also referred to as SpeedCore walls, are being used as innovative shear wall commercial high-rise buildings. These walls offer advantages such as modularity and construction schedule contraction. The cross-section of C- PSWs/CF consists of concrete infill sandwiched between the steel faceplates, where the steel plates are tied together by steel tie bars. Elevated temperatures will result in a deterioration in the mechanical properties of steel and concrete during a fire event in buildings. Such degradation can lead to stability-related failure of structural components. Composite floors are connected to these walls through simple shear connections. The floor-to-wall connections will be exposed to elevated temperatures, which may result in connection failure and progressive collapse of structures.</p><p dir="ltr">Designing SpeedCore walls without fire protection raises concerns regarding the performance of other structural components connected to SpeedCore walls under fire loading including composite floor systems and wall-to-floor connections. Numerical studies conducted on the connections and the floor systems indicated that these structural components undergo thermal compression forces during heating and tensile forces during the cooling phases of a fire event. The goal of this research was to develop an approach for performance-based fire resistance design of complete floor systems consisting of SpeedCore walls, composite floor slabs, and wall-to-floor connections.</p><p dir="ltr">This research includes experimental and numerical analyses to gain insight into the behavior of the floor-to-SpeedCore wall connections under fire and gravity loading. The specimens included steel beams connected to SpeedCore walls through simple shear connections. Three types of floor-to-wall connections were tested including connections with through-plate, reinforcing plate, and unreinforced plate. The parameters considered in the test matrix included: connection type, temperature, loading angle, and loading direction. These parameters in the test matrix were based on results obtained from previous numerical and experimental studies in the literature. The experimental results can fill the existing knowledge gap on floor-to-wall connections for steel-concrete composite members, develop design recommendations, and benchmark numerical models.</p><p dir="ltr">Numerical models were developed to simulate the behavior of the connections (member level) and whole structures (structure level) at ambient and elevated temperatures. Finite Element (FE) analysis and Component-based Models (CB) were utilized to develop the numerical models. The developed models were benchmarked by comparing the obtained numerical results with experimental data reported in the literature. FE models have been validated at two different levels, namely member level, and system level. The performance of the designed connection for the archetype structures was studied using benchmarked FE and CB models. The behavior of various wall-to-floor connections with different steel plate (C-PSW/CF) detailing was investigated.</p><p dir="ltr">Benchmarked numerical models were used to perform a parametric study to evaluate the performance of these connections. UP connection detail was used to perform the study due to its promising experimental performance, which does not need any special detail or plate reinforcement. The study was performed by evaluating the effects of critical parameters on the connection behavior namely, bolt size, target temperature, loading angles, and loading direction</p>