Without noise, a wireless system would be able to transmit and receive signals over an arbitrary long-distance. However, practical wireless systems are not noise-free, leading to a limited communication range. Thus, the design of low-noise devices (such as antennas, amplifiers, and filters) is essential to increase the communication range. Also, it is well known that the noise performance of a receiving radio is primarily determined by the frontend including the antenna, filter, and a low-noise amplifier. In our first design, we intend to reduce the noise level of the receiving system by integrating a parametric amplifier into the slot antenna. The parametric amplifier utilizes nonlinear and/or time-variant properties of reactive elements (capacitors and/or inductors) to amplify radio frequency signals. Also, the parametric amplifier offers superior noise performance due to its reactive nature. We utilize the parametric amplifier to design a low-noise active matching circuit for electrically small antennas in our second design. Using Chu's limit and the Bode-Fano bound, we show a trade-off between the noise and bandwidth of the electrically small antennas. In particular, to make the small antenna wideband, one needs to introduce a mismatch between the antenna and the amplifier. Due to the mismatch, the effect of the low-noise amplifier becomes even more critical and that is why we choose the parametric amplifier as a natural candidate. As a realized design, a loop antenna is configured as a receiver, and the up-converter parametric amplifier is connected to it leading to a low-noise and wideband active matching circuit. The structure is simulated using a hybrid simulation technique and its noise performance is compared to the transistor counterpart. Our simulation and measurement results show more than 20 times bandwidth improvement at the expense of a 2 dB increase in the noise figure compared to the passive antenna counterpart. / Doctor of Philosophy / Nowadays, there is a high demand for compact and high-speed electronic devices such as cellphones, tablets, laptops, etc. It is therefore essential to design a miniaturized wideband antenna. Unfortunately, a trade-off exists between the bandwidth and gain of small antennas. The trade-off is based on some fundamental limits and extends to all small and passive antennas, regardless of their shape or structure. By using an active component such as an amplifier, the gain-bandwidth trade-off can be improved. However, we show that the active component adds noise to the receiving system leading to a new trade-off between noise and bandwidth in the receiving structures. In other words, utilizing the active component does not solve the problem and just replaces the gain-bandwidth trade-off with the noise-bandwidth trade-off. To improve the noise-bandwidth trade-off, we propose a new receiving structure in which we use the parametric amplifier instead of a commercially available transistor amplifier. The noise performance of the parametric amplifier is extremely better than the transistor amplifier leading to lower noise for the specified bandwidth. In particular, we improved the noise performance of the receiving system by 3 dB leading to doubling the communication distance.

An active, broadband antenna module amenable for use in low cost phased arrays is proposed. The module consists of a Vivaldi antenna integrated with a frequency conversion integrated circuit. A method of orthogonally mounting endfire antennas onto an array motherboard is developed using castellated vias. A castellated active isolated Vivaldi antenna package is designed, fabricated, and measured. An 8x1 phased array of castellated, active Vivaldi antenna packages is designed and assembled. Each element has approximately one octave of bandwidth centered in X-band, and each is mounted onto a coplanar waveguide motherboard. Radiation patterns of the array are measured at several frequencies and scan angles.

This thesis presents solutions and studies related to the design of wideband antennas for wireless handheld terminal applications. A method of electrically shortening the terminal chassis length to obtain resonance at high frequencies has been proposed and evaluated, thereby increasing the antennas impedance bandwidth. No significant effect on the lower frequency band in a dual-band antenna prototype has been observed, making the method suitable for multi-band applications. The chassis has further been utilized as a zero-thickness 0.9 - 2.7 GHz high efficiency antenna by inserting a notch in the chassis center, and a feasibility study for typical phones has been performed. Additionally, the effect of talk position on the chassis wave-mode has been investigated, where the standard equivalent circuit model for terminal antennas has been modified to include the presence of the users head. The model has been used to explain measured and simulated effects concerning frequency detuning, efficiency reduction and bandwidth enhancements when the terminal is placed in talk position. The use of a hands-free earpiece cord is currently mandatory for FM radio reception as the cord is utilized as antenna. However, there is currently a market driven demand for removing the cord requirement since many modern phones are equipped with speakers and Bluetooth headsets. In this thesis, an active ferrite loop antenna is proposed as an internal replacement/complement with a performance of -23 dB (G/T degradation) compared to a full-size lossless dipole in urban environments. Also, a modification to the cord is suggested for DVB H reception. Complex matching networks have been investigated to increase the bandwidth of dual band PIFA antennas, and a printed dual band dipole has been integrated with a modified Marchand balun for dual resonance at two separate frequency bands, thus covering the commercial cellular bands 824-960 and 1710-2170 MHz with a single antenna.

<p>This thesis presents solutions and studies related to the design of wideband antennas for wireless handheld terminal applications. A method of electrically shortening the terminal chassis length to obtain resonance at high frequencies has been proposed and evaluated, thereby increasing the antennas impedance bandwidth. No significant effect on the lower frequency band in a dual-band antenna prototype has been observed, making the method suitable for multi-band applications. The chassis has further been utilized as a zero-thickness 0.9 - 2.7 GHz high efficiency antenna by inserting a notch in the chassis center, and a feasibility study for typical phones has been performed. Additionally, the effect of talk position on the chassis wave-mode has been investigated, where the standard equivalent circuit model for terminal antennas has been modified to include the presence of the users head. The model has been used to explain measured and simulated effects concerning frequency detuning, efficiency reduction and bandwidth enhancements when the terminal is placed in talk position.</p><p>The use of a hands-free earpiece cord is currently mandatory for FM radio reception as the cord is utilized as antenna. However, there is currently a market driven demand for removing the cord requirement since many modern phones are equipped with speakers and Bluetooth headsets. In this thesis, an active ferrite loop antenna is proposed as an internal replacement/complement with a performance of -23 dB (G/T degradation) compared to a full-size lossless dipole in urban environments. Also, a modification to the cord is suggested for DVB H reception.</p><p>Complex matching networks have been investigated to increase the bandwidth of dual band PIFA antennas, and a printed dual band dipole has been integrated with a modified Marchand balun for dual resonance at two separate frequency bands, thus covering the commercial cellular bands 824-960 and 1710-2170 MHz with a single antenna.</p>

Avec le développement de l’internet des objets et l’augmentation des applications sans fil, les antennes sont de plus en plus présentes au quotidien. Cependant, l’implantation de ces antennes est un challenge tant d’un point de vue technologique (intégration des antennes dans les dispositifs), que psychologique (acceptabilité des antennes par le grand public). Dans ce contexte, le développement d’antennes optiquement transparentes permet non seulement leur implantation sur de nouvelles surfaces (vitrages d’immeubles, écrans de smartphones ...), mais promeut aussi leur acceptabilité par le grand public grâce à leur faible impact visuel. Ce travail présente la conception, la fabrication et la caractérisation d’antennes actives optiquement transparentes. Le matériau transparent et conducteur utilisé est un maillage métallique à pas micrométrique développé spécifiquement, alliant conductivité électrique et transparence optique élevées. Dans ce cadre, un premier prototype d’antenne transparente et miniature en bande FM utilisant un transistor MESFET de dimensions sub-millimétriques a été réalisé. Des antennes agiles en fréquence en bande X (~10 GHz) couplées, soit à une diode varicap localisée (agilité ~10%), soit à un matériau ferroélectrique (agilité ~2%), ont été développées et étudiées. Une antenne passive transparente a été conçue en bande V (~60 GHz). Enfin, une transition optique (1540 nm) / hyperfréquence (1,4 GHz) a été réalisée et caractérisée, basée sur la transmission optique d’un faisceau laser au travers du matériau constitutif de l’antenne. Pour l’ensemble des prototypes réalisés, une transparence optique supérieure à 80% dans le domaine du visible associée à une résistance par carré inférieure à 0,1 ohm/sq ont été utilisées. / Within the development of the Internet of Things (IoT) and the increase of the wireless communications, antennas are even more present on everyday life. However, antenna implementation is a real challenge, from a technological point of view (antenna integration into the devices) and from a psychological point of view (acceptability by the general public). Within this framework, the development of optically transparent antennas on new surfaces (glass windows, smartphone screens . . . ) is of great interest to improve the network coverage and to assist the general public in acceptability thanks to the low visual impact of such printed antennas. The present work deals with the design, the fabrication and the characterization of optically transparent and active antennas. The transparent and conducting material used is a micrometric mesh metal film specifically developed, associating high electrical conductivity and high optical transparency. A first optically transparent and miniature FM antenna based on a MESFET transistor with micrometric size has been designed and fabricated. Frequency agile antennas operating in X-band (~10 GHz), based on a beam-lead varactor (agility ~10%) and on a ferroelectric material agility ~2%), have been developed and characterized. An optically transparent and passive antenna has been studied in V-band (~60 GHz). At last, optics (1540 nm) / microwave (1.4 GHz) transition has been performed based on the transmission of a laser beam through the transparent antenna. For all prototypes, an optical transparency level higher than 80% coupled with a sheet resistance value lower than 0.1 ohm/sq have been used.