No description available.

Wood as a construction material has in recent years increased, in particular concerningpedestrian bridges. By utilizing wood, the ecological footprint can be reduced,and the material can be designed to comply with the increasing aesthetic demandbridge designers are facing. However, as the material weighs little with respect toits bearing capacity, combined with design becoming more slender, human inducedvibrations are becoming a problem.Having this in mind, the objective of the thesis is to conduct a case study on anexisting timber pedestrian bridge and assess its dynamic parameters by means ofexperiential testing and numerical modelling. The case study concerns the Hägernäsbridge, an arch bridge located in Hägernäs, Täby. The thesis also considers seasonaleffects by conducting experiments on two separate occasions. In addition, the thesisevaluates influencing parameters on the dynamic behaviour by conducting a sensitivityanalysis. To aid the above mentioned objective, a literature review coveringsimilar type of analysis is conducted. The literature review also studies the seasonaleffect, mainly from the asphalt layer, as its stiffness contribution is temperaturedependant.The results from the dynamic parameters showed that not all modes fall above therecommended values concerning damping ratio (with values above 1-1.5%). However,all modes fulfill design criteria concerning the magnitude of the natural frequencies.Furthermore, results showed that the natural frequencies are highly temperaturedependant. The measured values during warm weather (+17C) resulted in lowervalues than those from the cold weather experiment (-10C). Moreover, the greatestdifference, by 21% was on the 1st transverse mode and the lower difference was onthe 1st vertical mode, that decreased by merely 5%. Moreover, the damping ratiowas calculated and it was not possible to find any correlation between warm andcold temperature. Instead, decreased temperature caused some modes to increase indamping ratio and others to decrease. The most affected mode was once again the1st transverse mode which increased by 146% going from warm to cold temperature

Av olika orsaker sker rörelser i strukturer, vilket leder till att deformationer uppstår. För att upptäcka deformationer krävs att förändringarna övervakas regelbundet. Övervakning kan ske på olika sätt. När detta utförs bör ett stomnät, upprättat av referenspunkter av god kvalitet, finnas tillgängligt. Stomnätet ger en grund för deformationsmätningen och gör att instrumentet som används, kan erhålla en lokalisering av var referenspunkterna placeras innan mätningen av strukturen utförs. 2014 utförde konsultföretaget Sweco, med uppdrag från Leksands kommun, en deformationsmätning av Leksandsbron, som är en gammal bågvalvsbro från 1925 i Leksands kommun, Dalarnas län. Syftet var att undersöka brons hållbarhet, men några slutsatser kunde inte dras utifrån den mätningen. I denna studie är syftet att ge förslag på hur Swecos stomnät skulle kunna utvecklas. Kompletteringen av stomnätet utfördes genom en simulering i programvaran SBG Geo där ett antal av Swecos kända stompunkter valdes och nya stompunkter placerades ut grafiskt med avseende på kvalitet, tillförlitlighet, geometri och ekonomiska aspekter i tre scenarier. Ett stomnät kan se ut på många olika sätt i teorin, men i praktiken är omgivningen begränsad vid bromätningar. Nätutjämning av förslagen fick senare klargöra vilket nät som var det bästa för att använda som referens till inmätningen av bron. Kompletteringen resulterade i att det förslag som var det mest lämpade också var det som var bäst anpassat till brons omgivning, natur och sikt. Det bästa förslaget har därefter användes därefter till inmätning av Leksandsbron, där Swecos deformationsmätning utgjorde referens. Inmätningen av stomnätet och bron utfördes med totalstationen Trimble S7. Genom nätutjämning beräknades nätets koordinater och osäkerheter från observationerna och differenserna jämfördes mot Swecos punkter för att se om någon deformation uppstått. Resultatet visar att två av Swecos punkter och några av brons punkter har utsatts för deformation. Deformationen för punkternas avvikelser analyserades också genom att använda t-student signifikanstest på ett konfidensintervall av 95%. Är avvikelsen inom intervallet har punkten inte rört sig och är avvikelsen utanför konfidensintervallet har punkten rört sig. Signifikanstestet visade att de punkter som utsatts för deformation i nätutjämningen även är signifikanta i t-student testet och bekräftade att punkterna har rört sig. / For different reasons there are movements in structures, which leads to deformations. To monitor deformations, the changes have to be monitored on a regular basis. Monitoring can take place in different ways. When doing this, a core network based on good quality reference points, should be available. The core network provides a basis for deformation measurements and allows the instrument to predict a suitable location before measuring of the structure. In 2014, the consultancy company Sweco, commissioned by Leksands municipality, made deformation measurements of Leksandsbron, an old arch bridge from 1925, situated in Leksand, Dalecarlia. The intention was to investigate the sustainability of the bridge, but it was not possible to draw any conclusions from the measurements from 2014. The purpose of this study is to give suggestions on how the core network from Sweco could be developed. The completion was performed by a simulation in SBG Geo Software where some known points from Sweco were chosen as a reference and new points were graphically placed in terms of quality, reliability, geometry and economic aspects in three scenarios. A core network can look in many different ways theoretically, but practically, and especially at bridge measurements, there are limitations. By network adjustment of the proposals it could be clarified, which network was the best one to use for the survey of the bridge. The result of the completion was that the best suited proposal also was the one best suited to the surroundings, nature and visibility of the bridge The best suggestion was used for the bridge measurement with Sweco´s deformation measurement as a reference. The survey of the core network and the points of the bridge was performed by the Trimble S7 total station. With network adjustment the coordinates and assurances were calculated and the differences were compared to Sweco points to see if any deformation had occurred. The result showed that two of Sweco´s points and some of the bridge points have been exposed to deformation. The deformation has also been analyzed for the deviations of the core network points and the bridge points by using t-student significance test of a confidence interval of 95%. If the deviation is within the range it´s considered that the point has not moved and if the deviation is outside the range it´s considered that the point has moved. The significance test showed that the same points that had been exposed to deformation in the network adjustment, also were significant in the t-student test, which confirms that the points have moved.

<p> </p><p>The aim of this Master Thesis is to assess the load carrying capacity of the Glomman Bridge outside of the Swedish city Örebro. The Glomman Bridge is an unreinforced concrete single span arch bridge with backfill. The bridge was constructed in 1923 on assignment from the Swedish National Railways (SJ).</p><p>The failure criteria used in this thesis is that the bridge collapses when any cross section in the concrete arch reaches its ultimate capacity. In reality, the bridge may manage heavier loads than this. When the capacity is reached in a cross section, a hinge is formed and the arch relocates the forces to other parts of the arch that can carry higher stresses. The real bridge will not collapse until a fourth hinge is formed, and by that a mechanism. To be able to calculate the cross section forces in the arch, it was necessary to know the influences of the loads on the arch when they were run along the bridge. For this purpose, influence lines were obtained from a 2D finite element model created in ABAQUS, a general FE-analyses software. A calculation routine to find the least favourable load combination was then created in Matlab, a numerical calculation software. The routine was made to find the worst case among different load cases and to combine the standardized axle pressures with the present number of axles.</p><p>A parametric survey was also performed because the material properties for the different parts of the bridge are very uncertain. In the survey, the initial values were changed one at a time to study the outcome on the load factor. The load factor is the ratio between the ultimate limit load and the actual load. The studied parameters are the compressive strength, the Young's modulus, the density and the Poisson's ratio of the different parts of the bridge. The parameters are studied individually irrespective of possible correlation. The studied parts of the bridge are the backfill, the arch, the abutments and the asphalt. The clearly most important component is found to be the backfill. With increased stiffness or increased Poisson's ratio in the backfill follows increased load factor.</p><p>The equations behind the failure envelope can be derived from equilibrium equations for the unreinforced cross section. The influence lines are normalised with respect to the capacity of the cross section to get the degree of efficiency along the whole length of the arch, instead of the common influence lines that give the cross section forces. This is done because the failure is not caused by large cross section forces but by an exceeded ultimate stress. As the different loads are run along the bridge, the largest positive and negative efficiency for bending moment and normal force are localised. The normalised cross section forces are plotted together with the failure envelope and the load factor is then calculated.</p><p>Several masonry arch bridges were loaded until collapse in a study performed by the British Transport and Road Research Laboratory. One of the bridges in the study, the Prestwood Bridge, has been used in this thesis as a comparison to the Glomman Bridge. The load carrying capacity of the Prestwood Bridge is known, and is used to verify that the method using the failure envelope is applicable.</p><p>To compare the results from the cross section analysis from the failure envelope model to another method, the Glomman Bridge and the Prestwood Bridge were also tested in the commercial software RING 2.0. The method used in RING 2.0 differs from the failure mode in this thesis by calculating the load factor when four different cross sections reach their capacity and the bridge collapses.</p><p>The failure envelope method allows an A/B-value (Axle- and Bogie load) of 102 kN/147 kN when using very poor values of the parameters and 181 kN/226 kN when using a reference case with normal parameters.</p><p>Although the load capacity is found to be acceptable, the uncertainties are still large. To get a more accurate apprehension of the condition of the actual bridge, further research should be carried out, such as e.g. a non-linear model.</p> / <p>Syftet med föreliggande examensarbete är att uppskatta bärförmågan hos bron Glomman utanför Örebro. Glomman är en oarmerad betongvalvbro i ett spann med ovanliggande jordfyllning. Bron byggdes 1926 på uppdrag av Statens Järnvägar (SJ).</p><p>Brottkriteriet i detta examensarbete är att bron går till brott när något tvärsnitt i betongbågen uppnår sin kapacitet. I själva verket är det möjligt att bron kan klara tyngre last än detta. När kapaciteten nås i ett tvärsnitt uppstår en led och bågen omlagrar krafterna till andra bågdelar som klarar större spänningar. Den verkliga bron rasar inte förrän en fjärde led har utvecklats, och därmed en mekanism. För att kunna beräkna tvärsnittskrafterna i bågen, var det nödvändigt att känna till trafiklasternas påverkan på bågen när de kördes över bron. För detta ändamål erhölls influenslinjer från en tvådimensionell finita elementmodell skapad i ABAQUS, ett generellt FE-program. En beräkningsrutin för att finna värsta tänkbara lastkombinering skapades i Matlab, ett numeriskt beräkningsprogram. Rutinen utformades för att hitta värsta fallet bland olika lastfall samt för att kombinera standardiserade axeltryck med det aktuella antalet axlar.</p><p>En parameterstudie utfördes också då materialegenskaperna för de olika delarna i bron är mycket osäkra. I parameterstudien ändrades ingångsvärdena ett åt gången för att studera utslaget på lastfaktorn. Lastfaktorn är förhållandet mellan brottgränslasten och den verkliga lasten. De parametrar som studeras är tryckhållfastheten, <em>E</em>-modulen, densiteten och tvärkontraktionen för de olika brodelarna. Parametrarna studeras enskilt utan hänsyn till eventuell korrelation. De brodelar som studeras är fyllningen, bågen, fundamenten och asfalten. Den klart viktigaste komponenten visar sig vara fyllningen. Med ökad styvhet eller ökad tvärkontraktion i fyllningen följer ökad last­faktor.</p><p>Ekvationerna bakom brottenveloppet kan härledas ur jämviktsekvationer för det oarmerade tvärsnittet. Influenslinjerna normeras med avseende på tvärsnittets kapa­citet för att få ut utnyttjandegraden längs hela bågen. Detta görs då det egentligen inte är för stor tvärsnittskraft som orsakar brott utan för stor spänning. Högsta och lägsta utnyttjandegrad för böjande moment och normalkraft lokaliseras när de olika typlasterna körs över bron. Utnyttjandegraderna placeras i brottenveloppet för att sedan räkna fram en lastfaktor.</p><p>Ett flertal liknande broar har lastats till brott i en studie genomförd av British Transport and Road Research Laboratory. En av broarna i studien, Prestwood Bridge, har använts i denna rapport som jämförelse med Glomman. Då bärförmågan hos Prestwood Bridge är känd används den till att bekräfta att metoden med brott­enveloppet är tillämpbar.</p><p>För att jämföra resultaten från tvärsnittsanalysen i brottenveloppmetoden med en annan metod, testades även Glomman och Prestwood Bridge i det kommersiella programmet RING 2.0. Metoden som används i RING 2.0 skiljer sig från brottmoden i denna rapport genom att istället beräkna lastfaktorn när fyra olika tvärsnitt har uppnått sina kapaciteter och bron kollapsar.</p><p>Metoden med brottenvelopp tillåter ett A/B-värde (Axel- och Boggitryck) på 102 kN/147 kN när mycket dåliga parametervärden används och 181 kN/226 kN när referensfallet med normala parametervärden används.</p><p>Även om bärförmågan kan anses vara acceptabel är osäkerheterna stora. För att få en nogrannare uppfattning om brons faktiska tillstånd bör fortsatta studier utföras, som t.ex. en icke-linjär modell.</p>

Objetivo: Avaliar pacientes reabilitados com prótese tipo protocolo mandibular e analisar o impacto do diferente número de implantes utilizados na taxa de sobrevivência dos implantes, perda óssea marginal e sobrevivência das próteses. Material e métodos: Esta revisão sistemática foi conduzida segundo orientações do PRISMA e registrada sob número de registo CRD42016048523 (PROSPERO). A base de dados electrônica PubMed/MEDLINE foi pesquisada para artigos publicados até 17 de julho de 2016 sem restrições quanto ao ano de publicação e teve como objetivo responder a seguinte pergunta em formato PICO: "Em pacientes desdentados, protocolos mandibulares suportados por três implantes, comparados com diferente número de implantes, mostram taxa de sobrevivência de implantes, perda óssea marginal e sobrevivência da prótese satisfatórios?" Os estudos foram avaliados segundo os níveis de evidência OCEBM e a qualidade metodológica foi avaliada de acordo com a escala MINORS e ferramenta de risco de viés Cochrane. Foi realizada a estatística descritiva quando aplicável. Curvas de sobrevivência para os implantes foram construídas com o metódo de Kaplan Meyer e a perda óssea marginal foi analisada pelos testes de kruskal-Wallis, Dunn’s e Mann Whitney. Resultados: 21 estudos foram incluídos na síntese quantitativa. 4712 implantes e 1245 protocolos mandibulares foram examinados em 1245 pacientes. Os resultados foram agrupados em categorias com base no número de implantes instalados em cada paciente: grupo 1 (três implantes) mostrou uma taxa de sobrevivência do implante de 90%, grupo 2 (4 implantes) apresentou 95% e o grupo 3 (cinco implantes) atingiu a menor taxa de sobrevivência do implante (74%). Os grupos 1 e 3 apresentaram os menores valores de perda óssea no primeiro ano (0,73 e 0,70 mm respectivamente), com diferença estatisticamente significante do grupo 2 que registrou mediana = 1,31 mm (p = < 0,001). Conclusão: Apesar das limitações quanto à falta de estudos de elevado nível de evidência e da própria metodologia da pesquisa por termos MeSH, pôde-se concluir que protocolos mandibulares suportados por três implantes demonstraram sobrevivência de implantes e perda óssea marginal no primeiro ano satisfatórios. A sobrevivência de próteses, no entanto, foi inferior aos demais grupos e isto sugere um maior acompanhamento de tais reabilitações a fim de esclarecer dados e buscar soluções. / Purpose: To assess edentulous patients rehabilitated by implant-supported mandibular full-arch bridges and to analyze the impact of the different number of implants used on implant survival rate, bone loss around the fixtures and prosthesis survival rate. Material and methods: This systematic review followed PRISMA guidelines and was registered on PROSPERO (registration number CRD42016048523). PubMed/MEDLINE electronic database was searched for articles published up until July 17th, 2016 without restrictions about publication year and aimed to answer the following question in PICO format: “In edentulous patients, full arch-bridges supported by three implants, compared to those with different number of implants, show satisfactory implant survival rate, bone loss and prosthesis survival rate?” Evidence level of studies were evaluated according to OCEBM e the methodological quality by MINORS scale and Cochrane Risk of Bias Tool. Descriptive statistics was performed when applicable. Implant survival curves were constructed with Kaplan-meyer method and marginal bone loss was analyzed with kruskal-Wallis, Dunn’s and Mann Whitney tests. Results: 21 studies were enrolled. Overall, 4712 implants and 1245 implant-supported fullarch bridges were examined in 1245 patients. Results were grouped on categories based on the number of fixtures on each patient: Group 1 (three implants) showed an implant survival rate of 90%, Group 2 (four implants) presented 95% and the Group 3 (five implants) reached the lowest implant survival rate (74%). Group 1 and Group 3 showed the lowest values of first year bone loss (0.73 and 0.70 mm respectively), statistically significant different of Group 2 that registered median = 1,31mm (p = <0.001). Conclusion: Despite of the limitations regarding the lack of high level of evidence studies and the methodology of MeSH terms research itself, it was concluded that full archbridges supported by three implants show satisfactory implant survival rate and first year bone loss. The prosthesis survival rate, however, was inferior to the other groups and this suggests a bigger follow-up of these rehabilitations with the aim of clarifying data and search for solutions. / Dissertação (Mestrado)

The subject of this thesis is alternative design of the pedestrian bridge over Brno reservoir near Veveří castle. Three preliminary studies are created. The chosen variant consists of a stress ribbon supported by a steel arches. Time dependent analysis of load cases effects during construction stages is calculated by ANSYS. The bridge is verified according to the European Standards.

The topic of my master's thesis is a concept and evaluation of a new steel construction of a foot bridge for pedestrians and cycles across the river Morava. The concept has two alternatives. Option 1: The foot bridge has three spans. The span lengths are 27+81+27m, the middle span is stiffened by an arc. There is a bridge deck that consists of a cellular beam which is locked onto the arc. The bridge deck is lower, steel and orthotropic. The arrangement of rods is radial. Option 2: The middle span is stiffened by two arcs bowed to each other. The bridge deck consists of two beams with crossbeams and is locked onto the arcs. The bridge deck is again lower, steel and orthotropic. The arrangement of rods is radial. The wind bracing has a shape of a Vierendeel beam.

Diploma thesis deals with a design of concrete arch structure. There was made a preliminary design of concrete structure of a buried arch bridge. Subsequently was the shape of arch structure optimized to oblige the requirements of real buried arch bridge structure. There is included static calculation of the ecoduct construction. It is developed detailed drawings

The subject of this master's thesis is design of road bridge over highway D1 by the city Přerov. From the three proposed solutions has been chosen bridge with self-anchored arched structure which is good for deep notch. The concrete bridge was designed and assessed according to current Eurocodes. The thesis includes detailed structural analysis, drawings and visualization of the bridge. The analysis was performed using software Scia Engineer including time dependent analysis (TDA). Assessment of structure was made in Excel or by hand.

The subject of this diploma thesis is design of arch bridge across the highway. Has been elected self-anchored structure with span of arch 60 m and trapezoid bridge deck from prestressed concrete. The load effects is calculated by software Scia Engineer including time dependent analysis. The supporting structure is assessed for the ultimate limit state and serviceability limit state. Static assessment is done by hand calculation according to CSN EN 1992-2. Part of the thesis is drawing and visualization of the bridge.