This dissertation proposes, studies and experimentally demonstrates novel liquid crystal (LC) optics to solve challenging problems in RF and photonic signal processing, freespace and fiber optic communications and microscopic imaging. These include free-space optical scanners for military and optical wireless applications, variable fiber-optic attenuators for optical communications, photonic control techniques for phased array antennas and radar, and 3-D microscopic imaging. At the heart of the applications demonstrated in this thesis are LC devices that are non-pixelated and can be controlled either electrically or optically. Instead of the typical pixel-by-pixel control as is custom in LC devices, the phase profile across the aperture of these novel LC devices is varied through the use of high impedance layers. Due to the presence of the high impedance layer, there forms a voltage gradient across the aperture of such a device which results in a phase gradient across the LC layer which in turn is accumulated by the optical beam traversing through this LC device. The geometry of the electrical contacts that are used to apply the external voltage will define the nature of the phase gradient present across the optical beam. In order to steer a laser beam in one angular dimension, straight line electrical contacts are used to form a one dimensional phase gradient while an annular electrical contact results in a circularly symmetric phase profile across the optical beam making it suitable for focusing the optical beam. The geometry of the electrical contacts alone is not sufficient to form the linear and the quadratic phase profiles that are required to either deflect or focus an optical beam. Clever use of the phase response of a typical nematic liquid crystal (NLC) is made such that the linear response region is used for the angular beam deflection while the high voltage quadratic response region is used for focusing the beam. Employing an NLC deflector, a device that uses the linear angular deflection, laser beam steering is demonstrated in two orthogonal dimensions whereas an NLC lens is used to address the third dimension to complete a three dimensional (3-D) scanner. Such an NLC deflector was then used in a variable optical attenuator (VOA), whereby a laser beam coupled between two identical single mode fibers (SMF) was mis-aligned away from the output fiber causing the intensity of the output coupled light to decrease as a function of the angular deflection. Since the angular deflection is electrically controlled, hence the VOA operation is fairly simple and repeatable. An extension of this VOA for wavelength tunable operation is also shown in this dissertation. A LC spatial light modulator (SLM) that uses a photo-sensitive high impedance electrode whose impedance can be varied by controlling the light intensity incident on it, is used in a control system for a phased array antenna. Phase is controlled on the Write side of the SLM by controlling the intensity of the Write laser beam which then is accessed by the Read beam from the opposite side of this reflective SLM. Thus the phase of the Read beam is varied by controlling the intensity of the Write beam. A variable fiber-optic delay line is demonstrated in the thesis which uses wavelength sensitive and wavelength insensitive optics to get both analog as well as digital delays. It uses a chirped fiber Bragg grating (FBG), and a 1xN optical switch to achieve multiple time delays. The switch can be implemented using the 3-D optical scanner mentioned earlier. A technique is presented for ultra-low loss laser communication that uses a combination of strong and weak thin lens optics. As opposed to conventional laser communication systems, the Gaussian laser beam is prevented from diverging at the receiving station by using a weak thin lens that places the transmitted beam waist mid-way between a symmetrical transmitter-receiver link design thus saving prime optical power. LC device technology forms an excellent basis to realize such a large aperture weak lens. Using a 1-D array of LC deflectors, a broadband optical add-drop filter (OADF) is proposed for dense wavelength division multiplexing (DWDM) applications. By binary control of the drive signal to the individual LC deflectors in the array, any optical channel can be selectively dropped and added. For demonstration purposes, microelectromechanical systems (MEMS) digital micromirrors have been used to implement the OADF. Several key systems issues such as insertion loss, polarization dependent loss, wavelength resolution and response time are analyzed in detail for comparison with the LC deflector approach. A no-moving-parts axial scanning confocal microscope (ASCM) system is designed and demonstrated using a combination of a large diameter LC lens and a classical microscope objective lens. By electrically controlling the 5 mm diameter LC lens, the 633 nm wavelength focal spot is moved continuously over a 48 [micro]m range with measured 3-dB axial resolution of 3.1 [micro]m using a 0.65 numerical aperture (NA) micro-objective lens. The ASCM is successfully used to image an Indium Phosphide twin square optical waveguide sample with a 10.2 [micro]m waveguide pitch and 2.3 [micro]m height and width. Using fine analog electrical control of the LC lens, a super-fine sub-wavelength axial resolution of 270 nm is demonstrated. The proposed ASCM can be useful in various precision three dimensional imaging and profiling applications.

In this study, the Dual Beam Phased Array Antenna System designed for COST260* project is upgraded to have the abilities of beam steering, tracking and direction finding by providing the necessary computer codes using C++ Programming Language. The functions of new prototype are tested to verify the operation. *COST260 project was an adaptive phased array receiving antenna system for satellite communication, which was operating at 11.49-11.678 GHz band.

In this thesis, a cavity-backed slot antenna array is designed for relatively wide instantaneous bandwidth, high gain and low sidelobes. The array consists of four, rectangular, slot elements, arranged side-by-side in a linear array and developed around 5GHz. Two feed points, at opposing sides of the printed array, each excite two of the slot elements through a series feed. This bidirectional feed presents symmetry to the design and prevents the tendency of beam-drift versus frequency as is common with many series-fed arrays. While being fed in-phase, the array will maintain boresight at broadside over the entire operating bandwidth. Also, the additional port allows for the potential introduction of a phase offset and, therefore, beam tilt. Finally, the printed array is designed to function within a quarter-wave, metallic cavity to achieve unidirectional radiation and improve gain.

The diploma thesis is aimed to design, optimize, produce and subsequently measure the properties of the reflector with the electronic steering direction for the frequency of the 24,125 GHz band ISM. The problem chosen is solved by a group of voltage-controlled varicaps. The reflector consists of a matrix of two rows, each containing 3 cells. The reflector was designed by full-wave software CST Microwave Studio 2015.

In recent years, multi-functional reconfigurable antennas (MRA) has attracted much attention in wireless communication. The reconfigurable antenna can adapt itself with changing system conditions, and it can provide different multi-functionalities which can give better system performances. Instead of using multiple antennas, a single reconfigurable antenna can provide the same performance and occupy less space. By using the parasitic layer technique, an antenna can be turned into a reconfigurable antenna. The main objective of this thesis is to study radiation pattern reconfiguration of the horn antenna by using the parasitic layer concept. The MRA consists of a single horn, dielectric loaded truncated pyramid (DLTP), and the parasitic layer. The antenna that is chosen in this thesis is the horn antenna because it provides high directivity. DLTP is used for magnification purpose. The results show that three modes of operations that provide better performances compared to the single horn antenna are achieved.

The full spatial covariance matrix of the multiple input multiple-output (MIMO) channel is an important quantity in channel modeling, communication system signal processing, and performance analysis, and therefore this matrix forms the heart of the research outlined in this dissertation. The work begins with an investigation of a generalized framework for computing the full MIMO spatial covariance based on the power angular spectrum (PAS) of the multipath field and the transmit and receive antenna element radiation patterns. For the case of uniform linear arrays and when the PAS clusters satisfy uniform, truncated Gaussian, or truncated Laplacian distributions, a series expansion is used to allow analytic evaluation of the required integrals in the formulation. The study also demonstrates the validity of some simplifying assumptions used to reduce the complexity of the covariance computation by applying the technique to ray tracing data as well as considers an analysis of the convergence properties of the series when computed using a finite number of terms. The insights and tools obtained from this covariance analysis are then used to develop a general approach for constructing MIMO transmit and receive beamforming vectors based on the full spatial covariance. While transmit and receive beamforming for the MIMO channel is a well-studied topic, when the transmit precoding is based on channel covariance information, developing near-optimal transmit and receive beamformers when the receiver is constrained to use linear processing remains an unsolved problem. This iterative beamforming algorithm presented here can accommodate different types of available channel information and receiver capabilities as well as either a sum power constraint or a per-antenna power constraint. While the latter is more realistic, construction of the optimal transmit precoder is less understood for this constraint. Simulation results based on measured channels demonstrate that the approach generates beamformer solutions whose performance rivals that achieved for an optimal nonlinear receiver architecture.

A monolithically integrated broadly tunable MQW laser that utilizes a combined impurity-free vacancy disordering (IFVD) of quantum wells and optical beam steering techniques is proposed and investigated experimentally. The device consists of a beam-steering section and an optical amplifier section fabricated on a GaAs/AlGaAs quantum well (QW) p-i-n heterostructure. The beam steering section forms a reconfigurable optical waveguide that can be moved laterally by applying separately controlled electrical currents to two parallel contact stripes. The active core of the gain section is divided in into selectively intermixed regions. The selective intermixing of the QW in the gain section results in neighboring regions with different optical bandgaps. The wavelength tuning is accomplished by steering the amplified optical beam through the selected region where it experiences a peak in the gain spectrum determined by the degree of intermixing of the QW. The laser wavelength tunes to the peak in the gain spectrum of that region. The IFVD technique relies on a silica (SiO2) capped rapid thermal annealing and it has been found that the degree of intermixing of the QW with the barrier material is dependent on the thickness of the SiO2 film. The QW sample is first encapsulated with a 400nm thick SiO2 film grown by plasma enhanced chemical vapor deposition (PECVD). In the gain section, the SiO2 film is selectively etched using multiple photolithographic and reactive ion etching steps whereas the SiO2 film is left intact in all the remaining areas including the beam-steering section. The selective area quantum well intermixing is then induced by a single rapid thermal annealing step at 975°C for a 20s duration to realize a structure with quantum well that has different bandgaps in the key regions. Optical characterizations of the intermixed regions have shown a blue shift of peak of the electroluminescence emission of 5nm, 16nm and 33nm for the uncapped, 100nm and 200nm iv respectively when compared to the as grown sample. The integrated laser exhibited a wavelength tuning range of 17nm (799nm to 816nm). Based on the same principle of QW selective intermixing, we have also designed and fabricated a monolithically integrated multi-wavelength light emitting diode (LED). The LED emits multiple wavelength optical beams from one compact easy to fabricate QW structure. Each wavelength has an independent optical power control, allowing the LED to emit one or more wavelengths at once. The material for the LED is the same AlGaAs/GaAs QW p-i-n heterostructure described above. The device is divided into selectively intermixed regions on a single QW structure using IFVD technique to create localized intermixed regions. Two different designs have been implemented to realize either an LED with multiple output beams of different wavelengths or an LED with a single output beam that has dual wavelength operation capabilities. Experimental results of the multiple output beams LED have demonstrated electrically controlled optical emission of 800nm, 789nm and 772nm. The single output LED has experimentally been shown to produce wavelength emission of 800nm and/or 772nm depending on electrical activation of the two aligned intermixed regions.

The development of phased array antenna systems requires considerable resources and time. Due to this constraint, the Naval Air Command (NAVAIR) needs a phased array that can be physically reconfigured to meet the demands of multiple missions without added development time or cost. This work develops and demonstrates a solution to this problem by implementing an adaptive calibration approach to the development of electronically steerable antennas (ESAs). In contrast to previous analog adaptive beamformer systems, this system allows for an arbitrary antenna configuration with a variable number of antenna elements and locations. A simulation model of arbitrary phased array configurations was developed to test the beamformer calibration algorithm and was used to show practical tile locations. To demonstrate this approach, four 4x4 ULA phased array antenna tiles were built and tested together in various configurations to show the viability of developing a physically reconfigurable phased array system.

No description available.

No description available.