The focus of this study was to determine the effects of pretreatment of wheat straw by superheated steam (SS) alone or in combination with boiling water (BW) on biomass structure and yields of fermentation products (cell mass and fermentation end-products) by Clostridium thermocellum. Different cultivars of wheat straw were ground to a particle size less than 355 µm, and exposed to the following methods of pretreatment: i) 15 min soaking in 119 °C boiling water under absolute pressure of 193 kPa, followed by processing with SS at atmospheric pressure at different temperatures and retention times; ii) 15 min processing with SS at atmospheric pressure; and iii) 15 min soaking in 119 °C boiling water under absolute pressure of 193 kPa. Processing with SS was conducted at a variety of temperatures in the range of 180-220 °C. The severity of pretreatment was expressed through a treatment severity factor as a measure of harshness of treatment. Pretreatment combinations of boiling water with superheated steam at different retention times inside the SS chamber were also investigated. Wheat straw samples were then used as substrates in fermentation reactions with C. thermocellum. The most noticeable effects on biomass structure and fermentation were observed at the highest severity factor of 6.5, corresponding to 15 min pretreatment with boiling water followed by 15 min treatment with SS at 220˚C. This pretreatment provided the maximum increase in percentage of contribution of amorphous cellulose (% CAC), and the highest fermentation yield in terms of hydrogen, carbon dioxide, and ethanol production. / October 2015

Since boiling heat transfer affords a very effective means to transfer heat, it is implemented in numerous technologies and industries ranging from large power generation plants to micro-electronic thermal management. Although having been a subject of research for several decades, an accurate prediction of boiling heat transfer is still challenging due to the complexity of the coupled mechanisms involved. It appears that the boiling heat transfer coefficient is intimately related to bubble dynamics (i.e. bubble nucleation, growth and detachment) as well as factors such as nucleation site density and interaction between neighbouring and successive bubbles. In order to contribute to the understanding of the boiling phenomenon, an experimental investigation of saturated pool boiling from a single or two neighbouring artificial nucleation sites on a polished copper surface has been performed. The bubble growth dynamics has been characterized for different wall superheats and a experimental growth law has been established. The interaction between successive bubbles from the same nucleation site has been studied, showing the bubble shape oscillations that can be caused by these interactions. The forces acting on a growing bubble has been reviewed, and a complete momentum balance has been made for all stages of bubble growth. The curvature along the interface has been measured, and indications concerning the mechanism of bubble detachment have been suggested. The rise of bubble after detachment has been investigated, and the maximum velocity reached before a change of direction has been estimated and compared to existing models from the literature. The interaction between bubbles growing side by side has been studied: the generation and propagation of a wave front during the coalescence of two bubbles has been highlighted. As boiling heat transfer enhancement techniques are being imagined and developed, this study also focuses on the electrohydrodynamic enhancement technique. Boiling experiments have been performed in the presence of electric fields, and their effects on heat transfer and bubble dynamics have been characterized. Although the volume of the bubbles at detachment and the relationship between the bubble frequency and the wall superheat were not affected, the bubble growth curve was modified. The bubbles were elongated in the direction of the electric field, and this elongation was estimated and compared to other studies from the literature. The rising velocity of the bubble was reduced in the presence of electric field, and the behaviour of bubbles growing side by side was modified, the electric field causing the bubbles to repeal each other. These results, obtained in a fully controlled environment, provide compelling evidence that electric fields can be implemented to alter the bubble dynamics and subsequently heat transfer rates during boiling of dielectric fluids.

Suvirinimas elektros lanku yra labai paplitęs visose pramonės šakose. Daugeliu atveju iškyla problemų skaičiuojant ir projektuojant įrenginius, kurie virina elektros lanku. Siekiant pašalinti šiuos sunkumus vis labiau nagrinėjami suvirinimo elektros lanku pereinamieji procesai. Virinant šiuo būdu įvykus trumpajam jungimui vyksta pereinamieji procesai, kurių metu gaunamas gamybinis brokas. Todėl norint pagerinti suvirinimo siūlės kokybę, siekiama, kad kuo greičiau atsistatytų visos sistemos darbinės charakteristikos. Didžiausią reikšmę suvirinant turi elektros lanko įtampa. Šiame darbe nagrinėjami suvirinimo lanko maitinimo šaltiniai, įtampos reguliavimo būdai ir suvirinimo lygintuvai. Tiriamojoje dalyje sudaryta funkcinė schema ir automatinio reguliavimo sistemos struktūrinė schema. Naudojantis programinės įrangos Matlab paketu apskaičiuoti pareinamieji procesai. / Electric arc welding is very popular in all branch of industry. There is a lot of problem to calculate and design equipments with boiling electric arc. On purpose eliminate this problems look into transition process for electric arc welder. Bolding in this way processing short conection we have transition process and get manufacturing spoilage. On purpose to have better welding seam we have to have more faster running system characteristic. The most biggest importance of bolding have voltage of welding seam. In this project we will research welding seam feeding sourse, voltage controlling way and bolding leveler. In the inquiring part we will build functional scheme and system flowchart of automatic control. Using Matlab program we will produse transitive process.

Two-phase heat transfer in mini/micro-channels is capable of meeting the high cooling demands of modern high heat flux applications. The phase change process ensures better temperature uniformity and control for local hot spots. Furthermore, these compact channels could be helpful in reducing the required charge and material inventories.Environmental concerns—mainly ozone depletion and global warming—have instigated a search for new alternatives in refrigeration industry. While new compounds are being developed to address stringent legislative demands, natural alternatives are also coming into prominence. A limited number of investigators have reported on thermal performance of such alternatives. The current study is therefore focused on saturated flow boiling heat transfer, pressure drop and dryout characteristics for three low global warming potential (GWP) refrigerants (R152a, R600a and R1234yf) in a vertical mini-channel.In this study experiments were carried out by uniformly heating a test section (stainless steel tube with 1.60 mm inside diameter and 245 mm heated length) at 27 and 32 oC saturation temperature with 50-500 kg/m2s mass velocities. The effects of various parameters of interest (like heat flux, mass flux, system pressure, vapor quality, operating media) on flow boiling heat transfer, frictional pressure drop and dryout characteristics were recorded. R134a, which has been widely used in several applications, is utilized as a reference case for comparison of thermal performance in this study.Experimental results for saturated boiling heat transfer showed strong influence of heat flux and system pressure with insignificant contributions from mass flux and vapor quality. Two phase frictional pressure drop increased with mass flux, vapor quality and with reduced operating pressure. The dryout heat flux remained unaffected with variation in saturation temperature, critical vapor quality in most cases was about 85%. The experimental results (boiling heat transfer, two-phase pressure drop and dryout heat flux) were compared with well-known macro and micro-scale correlations from the literature. / <p>QC 20141124</p>

The high ozone depletion and global warming potentials of fluorocarbon refrigerants have resulted in prohibitions and restrictions in many markets. Hydrocarbon refrigerants have low environmental impacts and are successfully used in domestic refrigerators and car air conditioners but replacing fluorocarbons in centrifugal chillers for air conditioning applications is unknown. Hydrocarbon replacements need a heat transfer correlation for refrigerant in flooded evaporators and predictions for operating conditions, capacity and performance. Safety precautions for large quantities of hydrocarbon refrigerants are needed and control of overpressure in plantrooms requires accurate prediction. Reliable correlations exist for forced convection in a single phase flow, condensation outside tubes and evaporation off sprayed tubes. For flooded evaporators this thesis proposes a new correlation for forced convection boiling of any refrigerant. An enhancement factor is combined with a modified Chen coefficient using recent pool boiling and forced convection correlations outside tubes. This correlates within typically a factor of two to known boiling literature measurements for CFC-113, CFC-11, HCFC-123, HFC-134a and HC-601. The operating conditions, capacity and performance of replacement hydrocarbons in centrifugal chillers were predicted using fluorocarbon performance as a model. With the new heat transfer correlation hydrocarbon predictions for flooded evaporators were made. For any fluorocarbon refrigerant there exists a replacement mixture of hydrocarbons which with a rotor speed increase about 40% gives the same cooling capacity in the same centrifugal chiller under the same operating conditions. For example replacing HCFC-123 in a flooded evaporator with HC-601/602 [90.4/9.6] and increasing the rotor speed by 43% will increase the coefficient of performance by 4.5% at the same cooling capacity. The maximum plantroom overpressure considered was from leakage and ignition of a uniform air/refrigerant mixture with maximum laminar burning velocity. Flow was modelled using a turbulence viscosity due to Launder and Spalding and turbulent deflagration using a reaction progress variable after Zimont. These partial differential equations were solved approximately for two and three dimensional geometries using finite volume methods from the Fluent program suite. Simple overpressure predictions from maximum flame area approximations agreed with Fluent results within 13.7% promising safe plantroom design without months of computer calculation.

Thesis (doctoral)--Helsinki University of Technology, 2004. / Includes bibliographical references (p. 146-154). Also available on the World Wide Web.

Thesis (M.S.)--University of Wisconsin -- La Crosse, 1980. / Includes bibliographical references (leaves 105-111).

abstract: Microchannel heat sinks can possess heat transfer characteristics unavailable in conventional heat exchangers; such sinks offer compact solutions to otherwise intractable thermal management problems, notably in small-scale electronics cooling. Flow boiling in microchannels allows a very high heat transfer rate, but is bounded by the critical heat flux (CHF). This thesis presents a theoretical-numerical study of a method to improve the heat rejection capability of a microchannel heat sink via expansion of the channel cross-section along the flow direction. The thermodynamic quality of the refrigerant increases during flow boiling, decreasing the density of the bulk coolant as it flows. This may effect pressure fluctuations in the channels, leading to nonuniform heat transfer and local dryout in regions exceeding CHF. This undesirable phenomenon is counteracted by permitting the cross-section of the microchannel to increase along the direction of flow, allowing more volume for the vapor. Governing equations are derived from a control-volume analysis of a single heated rectangular microchannel; the cross-section is allowed to expand in width and height. The resulting differential equations are solved numerically for a variety of channel expansion profiles and numbers of channels. The refrigerant is R-134a and channel parameters are based on a physical test bed in a related experiment. Significant improvement in CHF is possible with moderate area expansion. Minimal additional manufacturing costs could yield major gains in the utility of microchannel heat sinks. An optimum expansion rate occurred in certain cases, and alterations in the channel width are, in general, more effective at improving CHF than alterations in the channel height. Modest expansion in height enables small width expansions to be very effective. / Dissertation/Thesis / M.S. Mechanical Engineering 2011

abstract: A relatively simple subset of nanotechnology - nanofluids - can be obtained by adding nanoparticles to conventional base fluids. The promise of these fluids stems from the fact that relatively low particle loadings (typically <1% volume fractions) can significantly change the properties of the base fluid. This research explores how low volume fraction nanofluids, composed of common base-fluids, interact with light energy. Comparative experimentation and modeling reveals that absorbing light volumetrically (i.e. in the depth of the fluid) is fundamentally different from surface-based absorption. Depending on the particle material, size, shape, and volume fraction, a fluid can be changed from being mostly transparent to sunlight (in the case of water, alcohols, oils, and glycols) to being a very efficient volumetric absorber of sunlight. This research also visualizes, under high levels of irradiation, how nanofluids undergo interesting, localized phase change phenomena. For this, images were taken of bubble formation and boiling in aqueous nanofluids heated by a hot wire and by a laser. Infrared thermography was also used to quantify this phenomenon. Overall, though, this research reveals the possibility for novel solar collectors in which the working fluid directly absorbs light energy and undergoes phase change in a single step. Modeling results indicate that these improvements can increase a solar thermal receiver's efficiency by up to 10%. / Dissertation/Thesis / Ph.D. Mechanical Engineering 2011

Political, environmental and marketing factors mean there is a global requirement to produce vehicles with improved fuel economy and reduced emissions. This thesis shows that the gasoline direct injection (GDI) engine will continue to form a significant portion of the automotive propulsion market in the short to medium term. However, to reach future targets continuous development and optimisation of these engines is essential. The introduction to this thesis discusses the role some of the key aspects of GDI engine design have on overall engine efficiency. The fuel spray is shown to be a key contributor to this, as it is a primary driver in the fuel/air mixing process, and therefore intrinsically linked to the combustion efficiency.