O presente trabalho consiste basicamente no desenvolvimento de um programa de engenharia denominado SAJ (sistema de análise de juntas) capaz de realizar uma análise detalhada do comportamento de dois dos diversos tipos de juntas coladas existentes, a junta simples colada (\"single lap joint\") e a junta dupla colada (\"double lap joint\"). Sendo que foram analisadas juntas coladas com aderentes de material compósito ou, então, compostas de aderentes de compósitos e metal. O programa de engenharia desenvolvido possibilita o cálculo das tensões, dos esforços e dos deslocamentos nessas juntas. Para validar o referido programa, os resultados obtidos do mesmo foram confrontados com os resultados obtidos para condições semelhantes utilizando \"softwares\" comerciais de elementos finitos e de cálculo de juntas. Após a validação do programa, são apresentados alguns estudos de fatores que influenciam na resistência da junta colada, verificando a influência do comprimento de \"overlap\" (sobreposição), a rigidez do adesivo e a espessura da camada adesiva. Também é apresentada uma análise de falha dos aderentes de compósito evidenciando assim, as potencialidades e limitações desta ferramenta computacional para a área de desenvolvimento de produto. / This work consists on the development of software called SAJ which can analyze a bonded joint behavior in detail, not only for single lap joint, but also, for double lap joint. These joints could be made of composite/composite materials or metal/composite as adherentes. The software developed can calculate the joints stresses, loads and displacements. The results obtained are compared to the results obtained using commercial software and the same problems proposed. After the validation of SAJ, some studies were performed in order to determine how some characteristics affect the joint stresses distribution as overlap length, adhesive elastic modulus, adhesive thickness and a failure analysis of composite adherents showing the potential and limitation of this computational tool for the product development area.

No description available.

This dissertation is to obtain an overall understanding of the crack path selection in adhesively bonded joints. Using Dow Chemical epoxy resin DER 331® with various levels of rubber concentration as an adhesive, and aluminum 6061-T6 alloy with different surface pretreatments as the adherends, both symmetric and asymmetric double cantilever beam (DCB) specimens are prepared and tested under mixed mode fracture conditions in this study. Post-failure analyses conducted on the failure surfaces indicate that the failure tends to be more interfacial as the mode II component in the fracture increases whereas more advanced surface preparation techniques can prevent failure at the interface. Through mechanically stretching the DCB specimens uniaxially until the adherends are plastically deformed, various levels of T-stress are achieved in the specimens. Test results of the specimens with various T-stresses demonstrate that the directional stability of cracks in adhesive bonds depends on the T-stress level. Cracks tend to be directionally stable when the T-stress is compressive whereas directionally unstable when the T-stress is tensile. However, the direction of crack propagation is mostly stabilized when more than 3% mode II fracture component is present in the loading regardless of the T-stress levels in the specimens. Since the fracture sequences in adhesive bonds are closely related to the energy balance in the system, an energy balance model is developed to predict the directional stability of cracks and the results are consistent with the experimental observations. Using the finite element method, the T-stress is shown to be closely related to the specimen geometry, indicating a specimen geometry dependence of the directional stability of cracks. This prediction is verified through testing DCB specimens with various adherend and adhesives thicknesses. By testing the specimens under both quasi-static and low-speed impact conditions, and using a high-speed camera to monitor the fracture sequence, the influences of the debond rate on the locus of failure and the directional stability of cracks are investigated. Post-failure analyses suggest that the failure tends to be more interfacial when the debond rate is low and tends to be more cohesive when the debond rate is high. However, this rate dependence of the locus of failure is greatly reduced when more advanced surface preparation techniques are used in preparing the specimens. The post-failure analyses also reveal that cracks tend to be more directionally unstable as the debond rate increases. Finally, employing interface mechanics and extending the criteria for the direction of crack propagation to adhesively bonded joints, the crack trajectories for directionally unstable cracks are predicted and the results are consistent with the overall features of the crack paths observed experimentally. / Ph. D.

Fiber-reinforced composites comprise an important class of lightweight materials which are finding increasing applications in engineering structures including body components of automobiles and aircraft. Traditionally, synthetic fibers made of glass, carbon, etc. along with a polymeric resin have constituted the most common composites. However, due to environmental concern, occupational health safety considerations, higher cost, etc., research has been focused on substituting synthetic fibers, especially glass fibers with safer, economic and biodegradable natural fibers. Due to the ease of availability and affordability in terms of cost, woven jute mats, among a wide variety of natural fiber-based reinforcements, offer a good choice in combination with a suitable resin such as polyester or epoxy for fabrication of composite laminates. In structural applications, joining of parts made of jute fiber-reinforced composites (JFRCs) would be a natural requirement. Alternatives to joining processes for metals such as welding, riveting, etc. are required for composites. A joining process of high potential is adhesive bonding which has the advantages of reducing stress concentration, permitting fastening of dissimilar materials, etc. In the present study, adhesively bonded joints of JFRCs and their mechanical behavior are investigated under quasi-static and cyclic loading conditions. Initially, characterization of substrates is carried out under monotonic loading. This is followed by determination of stress- Strain curves, failure load and mean shear strength of bonded joints as functions of joint curing temperature and overlap length using a two-part structural epoxy adhesive. All tests are carried out according to relevant ASTM standards. It has been observed that higher curing temperatures give rise to only marginally high failure load and mean shear stress at failure compared to curing at room temperature. For a given curing temperature, failure load increases while mean shear strength decreases with respect to overlap length in both types of joints. As fatigue failure is a crucial consideration in design, the behavior of adhesively bonded JFRC joints is studied for the first time under cyclic loading conditions leading to the commonly-used S-N curve for characterization of failure of materials at different loading-unloading cycles. Interestingly, the fatigue strength for infinite life of adhesively bonded JFRC joints turns out to be approximately 30% of the quasi-static strength, a correlation which usually applies to materials in general. The effect of joint overlap length on fatigue life is studied and it is observed that the above relation between fatigue and quasi static strength is retained for different overlap lengths. Additionally, insights are provided into failure modes of joints under different loading conditions and for varying overlap lengths. Various empirical predictors such as exponent, power and hybrid models fitting the S-N curve are obtained and their relative efficacy (in terms of Coefficient of Determination R2, Adjusted-R2, Akaike’s Information Criterion and Residual Sum of Squares) enumerated in prediction of failure load including quasi-static failure load. As numerical simulation is an indispensable tool in designing geometrically complex structures under nonlinear conditions including failure and contact, finite element modeling of JFRC substrates, bulk adhesive and adhesively bonded joints has been investigated using implicit and explicit LS-DYNA solvers. In this context, the effects of various modeling parameters (mesh size and loading rate) and details of constitutive models capable of capturing plasticity and failure in an orthotropic composite and isotropic adhesive are discussed. Mesh size has been found to be an important parameter affecting computed results. Finally, a good correlation within ~(4% - 7%) was found between the predicted and experimental results for JFRC substrates, bulk adhesive and adhesively bonded single lap joints.

Le programme de recherche développé dans le cadre de cette thèse a pour principal objectif de concevoir, réaliser et valider une méthodologie d'étude des effets du vieillissement des interfaces collées, basée sur l'utilisation d'un dispositif de fluage innovant pouvant être couplé à un vieillissement hygrothermique. Celui-ci reprend la configuration classique de joint à double recouvrement mais permet de solliciter sous charge constante l'assemblage collé béton/composite. Il présente de plus certaines spécificités (zones de joint non sollicitées, compatibilité avec une machine d'essai à simple recouvrement existante,...) qui permettent de recueillir un grand nombre de résultat expérimentaux complémentaires. En premier lieux, nos travaux présentent une synthèse bibliographique retraçant le contexte du renforcement par composites collés et précisant les principaux mécanismes physico-chimiques susceptibles d'affecter la durabilité des adhésifs. Le manuscrit décrit ensuite les travaux expérimentaux menés pour étudier le comportement mécanique et physico-chimique des deux adhésifs sélectionnés pour la réalisation des joints collés béton/composites. Finalement, une approche prédictive basée sur i) des tests de fluage thermo-stimulés, ii) sur l'application du Principe de Superposition Temps-Température et iii) sur l'utilisation du modèle rhéologique de Burger, a permis de proposer un modèle de fluage non linéaire pour chacun des deux systèmes de colle. La seconde partie des travaux expérimentaux concerne la conception et la validation d'un dispositif innovant destiné à la caractérisation du comportement en fluage des interfaces collées béton/composite. Un élément important du cahier des charges de ce dispositif était d'en limiter l'encombrement, de sorte qu'il soit possible de tester plusieurs corps d'épreuve dans une chambre climatique au volume réduit, en vue d'étudier les effets synergiques du fluage et du vieillissement environnemental sur la durabilité des joints collés. Dans ce contexte, un prototype capable de solliciter en fluage trois corps d'épreuves à double recouvrement réalisés avec le procédé de renforcement Sika®Carbodur®S et connectés sur un unique circuit hydraulique, a été conçu et réalisé. Les résultats issus du prototype ont permis de le valider, en vérifiant notamment le maintient dans le temps de la charge appliquée, et le comportement symétrique des corps d'épreuve à double recouvrement. Le comportement mécanique des interfaces collées s'est révélé répétable, symétrique et conforme aux diverses modélisations réalisées, soit en calculant la réponse instantanée de l'interface au moyen d'un logiciel aux Eléments Finis (E.F.) ou à partir du modèle analytique de Volkersen, soit en calculant la réponse différée de l'interface en intégrant le modèle de fluage non linéaire de l'adhésif identifié précédemment dans le calcul aux E.F.. La dernière partie des travaux présentés dans le manuscrit concerne la réalisation d'un banc complet de fluage impliquant 14 corps d'épreuves à double recouvrement. Ces corps d'épreuve sont réalisés pour moitié avec le système de renforcement Sika®Carbodur®S et pour l'autre moitié avec le système Compodex. Le banc de fluage est installé dans la salle de vieillissement hygrothermique du Département Laboratoire d'Autun (40°C ; 95% H.R.). Tous les corps d'épreuves sont sollicités en fluage par un système de chargement alimenté par un circuit hydraulique similaire à celui utilisé pour le prototype, mais complété par une centrale hydraulique régulant la pression à partir de la mesure d'un capteur de pression. Pour compléter ces caractérisations sur interfaces collées, des essais de vieillissement sont également menés sur des éprouvettes d'adhésifs massiques stockées dans la salle climatique, certaines d'entre elles étant simultanément soumises à des sollicitations de fluage / The main objective of the present research is to design, realize and validate a methodology for studying ageing of bonded interfaces, based on the development of an innovative experimental creep device that can be coupled to hydrothermal aging. This device is based on the double-lap joint shear test configuration and enables to apply a constant load to the bonded assembly. In addition, this device combines other complementary features (unsolicited bonded joint zones, compatibility with an existing single lap shear test machine ...) that allows collecting useful complementary data. First, our work presents a literature review outlining the context of strengthening by bonded composite and specifying the main physicochemical mechanisms that may affect the durability of adhesive joints. Then, the manuscript describes the experimental characterizations carried out to assess both mechanical and physicochemical behaviors of the two adhesives selected for this study and which will be used to bond the composite on RC specimens in a later stage. Finally, a predictive approach based on i) thermo-stimulated creep tests, ii) on the application of the Time-Temperature-Superposition Principle and iii) on the use of the Burger's rheological model, allowed us to propose a non-linear creep model for each of the two adhesive systems. The second part of the experimental work is devoted to the design and validation of an innovative device for characterizing the creep behavior of concrete / composite adhesively bonded interfaces. An important requirement in the specifications was to reduce the size of the experimental device, so that several test specimens could be installed in a climatic room of limited volume, in order to study the synergistic effects of creep and hydrothermal ageing on the joint durability. In this line, a prototype involving three double-shear test-specimens loaded by flat jacks actuated by a centralized hydraulic system, was designed and realized (test-specimens were prepared using the Sika®Carbodur® S strengthening system). Collected data made it possible to validate the creep setup, by checking the constancy of the applied load over time, and the symmetrical behavior of the double lap shear test bodies. The mechanical behavior of the bonded interfaces was found to be repeatable, symmetrical and in a fair agreement with numerical and analytical modeling, done either by calculating the instantaneous response of the interface using a finite element (FE) approach and the analytical Völkersen's model, or by simulating the delayed creep response of the interface using a FE model in which the non-linear creep behavior of the adhesive layer had been implemented. The last chapter of the manuscript presents the realization of a full-scale creep setup involving fourteen double lap test specimens. Half of the test specimens were strengthened with Sika®Carbodur ® S and the other half with Compodex® C12 reinforcing composite system. This creep setup was installed in the climatic room of the Département Laboratoire d'Autun (40°C, 95% R.H.). Test specimens are creep loaded thanks to flat jacks powered by a hydraulic system similar to that used in the prototype, but supplemented by an electronic station that ensures pressure regulation in the circuit, based on the measurements of a pressure sensor. Beside these characterizations of bonded interfaces, complementary tests are also conducted on samples of the buk adhesive material stored in the climatic room, some of these samples being simultaneously subjected to creep loading

In this thesis, a new modeling methodology applicable to adhesively bonded joints for crash simulations is presented. Using this approach, adhesive joints can be modeled without using minute solid elements thus reducing the size of the model. Moreover, coarse mesh can be used for substrates in the overlap region of a joint. Both of these improvements together yield significant reduction in simulation run times in crash analysis when compared to solid element representation of adhesive. The modeling can also capture effects of strain rate for a given ambient temperature. In order to develop the efficient modeling procedure mentioned above, experimental, analytical and numerical studies have been carried out. Mechanical behaviors of adhesively bonded joints are studied with the help of double lap shear (DLS) coupon tests conducted at different extension rates and temperatures. The joint specimens are made from dual-phase (DP) steel coupons bonded with epoxy resin. Tests are also carried out to ascertain the behaviors of these component materials at different extension rates and temperatures. A new semi-analytical solution procedure is developed considering material nonlinearity to predict mechanical behaviors of adhesively bonded DLS joints. The joint behaviors using the semi-analytical approach are predicted separately using the Von Mises and exponent Drucker-Prager yield criteria. The predicted force versus extension curves using semi-analytical solution are compared with test results. It is also hypothesized here that, the semi-analytical solution procedure can be used as a base to develop efficient modeling procedures of adhesively bonded joints in FEA. In finite element analysis, both adhesive and substrates are modeled as elastic-plastic materials. It is shown that the shell-solid model of the DLS joint, in which substrates are modeled using shell elements and adhesive is modeled using solid elements, can accurately predict the mechanical behavior of the joint. Both exponent Drucker-Prager and Von Mises material models in ABAQUS are used to calculate force versus extension curves. Numerical and experimental forces versus extension curves are compared. A new methodology for efficient modeling of adhesively bonded joints in LS-DYNA using equivalent material properties in the joint overlap region is proposed. Various models using this methodology are assessed by comparing their results with shell-solid model and test results. Finally, it is also shown that strain rate effects can be included in the efficient modeling approach.

Le travail présenté dans ce mémoire avait pour objectif d'étudier le processus de la pénétration d'eau dans les composites en carbone/époxyde dans un premier temps, et dans un deuxième temps, d'étudier l'effet de la prise en eau par ces matériaux sur les performances mécaniques des composites et leur joints collés. L'intégration de ces phénomènes physiques dans la modélisation numérique est d'une grande importance dans la prédiction de la durabilité d'une structure en composite subissant un vieillissement hygrothermique. Par conséquent, ce travail consiste non seulement en des observations expérimentales, mais aussi en des simulations numériques. Des corrélations entre les résultats obtenus permettent d'une part de mieux comprendre ce qui se passe dans un système composite avec l'assemblage collé soumis à des charges mécaniques, de l'initiation d'endommagement jusqu'à la rupture finale ; d'autre part, de valider un modèle numérique robuste dans le but de la conception et de l'optimisation. Les originalités de ce travail se situent à différents niveaux en proposant : 1. un nouveau modèle de diffusion à deux-phases permettant de mieux décrire l'effet de l'épaisseur des stratifiés sur la pénétration de l'eau; 2. un nouveau modèle RPM " Residual Property Model " afin de prévoir la dégradation des propriétés mécaniques due à la prise en eau ; 3. une nouvelle loi de traction-séparation linéaire-exponentiel pour décrire la courbe-R observée dans les essais DCB en mode I pur sur les composites stratifiés afin de les intégrer plus facilement dans les modèles numériques

Στην παρούσα διπλωματική εργασία αναπτύχθηκε τρισδιάστατο αριθμητικό μοντέλο με βάση την μέθοδο των πεπερασμένων στοιχείων για την προσομοίωση της μηχανικής συμπεριφοράς συνδέσεων με κόλλα πολύστρωτων πλακών. Το μοντέλο αναπτύχθηκε χρησιμοποιώντας το εμπορικό πακέτο πεπερασμένων στοιχείων ANSYS. Για την προσομοίωση της συμπεριφοράς της κόλλας χρησιμοποιήθηκαν δύο προσεγγίσεις: η μοντελοποίηση της ζώνης συνοχής και η μοντελοποίηση της βλάβης του συνεχούς μέσου. Οι δύο αυτές προσεγγίσεις συγκρίθηκαν τόσο ως προς την αξιοπιστία τους, η οποία καθορίζεται από την σύγκριση με πειραματικά αποτελέσματα, όσο και ως προς την ευκολία εφαρμογής τους, η οποία καθορίζεται από τα δεδομένα που απαιτούνται και τον υπολογιστικό χρόνο. Η σύγκριση των δύο μεθοδολογιών έγινε στην βάση της εφαρμογής τους για την προσομοίωση της μηχανικής συμπεριφοράς σε φόρτιση τύπου Ι σύνδεσης με κόλλα μεταξύ δύο ψευδοισότροπων CFRP πολύστρωτων πλακών. Το συγκεκριμένο πρόβλημα επελέγη διότι υπήρχαν διαθέσιμα πειραματικά αποτελέσματα προς σύγκριση στο Εργαστήριο. Οι πολύστρωτες πλάκες μοντελοποιήθηκαν χρησιμοποιώντας το στρωματικό στοιχείο του ANSYS SOLID185. Στο στοιχείο αυτό κάθε στρώση μοντελοποιείται ξεχωριστά ως ορθότροπο υλικό. Η εφαρμογή της μοντελοποίησης της ζώνης συνοχής έγινε μέσω της χρήσης του στοιχείου του ANSYS INTER205. Για την εφαρμογή της μοντελοποίησης της βλάβης του συνεχούς μέσου αναπτύχθηκε μακρο-ρουτίνα χρησιμοποιώντας την γλώσσα προγραμματισμού του κώδικα ANSYS. Τα αριθμητικά αποτελέσματα έδειξαν ότι και οι δύο μεθοδολογίες προσομοιώνουν με ικανοποιητική ακρίβεια την καμπύλη δύναμης-μετατόπισης της σύνδεσης. Σχετικά με την ευκολία εφαρμογής των δύο μεθόδων, η σύγκριση έδειξε ότι η μέθοδος της μοντελοποίησης της ζώνης συνοχής υπερτερεί έναντι της μεθόδου μοντελοποίησης της βλάβης του συνεχούς μέσου διότι απαιτεί μικρότερο αριθμό δεδομένων, μειονεκτεί όμως ως προς τον απαιτούμενο υπολογιστικό χρόνο. Και οι δύο μέθοδοι κρίνονται κατάλληλες για χρήση στην αριθμητική σχεδίαση συνδέσεων με κόλλα. / This work is based on the development of three-dimensional numerical model based on the finite element method to simulate the mechanical behavior of adhesive bonded joints in composite materials. The model was developed in finite element procedures under the framework of the commercial software ANSYS. To simulate the behavior of the adhesive used two approaches: the cohesive zone modeling (CZM) and the continuum damage modeling (CDM). These two approaches are compared both in terms of reliability, which is determined by comparison with experimental results, and applicability, which is determined by the parameters required and the computational time. The comparison between the two methodologies was the basis of their application to simulate the mechanical behavior under mode-I fracture behavior of adhesively bonded joints between two CFRP plates. This problem was chosen because there were experimental results to compare in the laboratory. The sandwich plates are modeled using the stromal element of ANSYS SOLID185. This item each layer separately modeled as orthotropic material. The adhesive is modeled using the interface element of ANSYS INTER205. For the purpose of modeling the failure of continuous medium developed macro routine using the programming language code ANSYS. The numerical results showed that both methodologies simulate sufficient precision the curve force-displacement of the connection. About applicability of the two methods, the comparison showed that the process of cohesive zone modeling outweighs the process of continuum damage modeling because it requires less number of parameters, but falls to the computational time. Both methods are suitable for use in numerical design of adhesively bonded joints.

Zum kraft- und formschlüssigen Fügen von dünnwandigen, filigranen Betonfertigteilen eignen sich besonders kontinuierliche, flächige Verbindungen, die durch Verkleben erzielt werden können. Im Rahmen dieses Vorhabens sollten möglichst einfach zu handhabende Klebverbindungen für Platten- und Scheibenbauteile konstruiert und optimiert werden. Die Verbindungen sollten so ausgelegt werden, dass sie sowohl Beanspruchungen aus einzelnen Schnittgrößen als auch aus Schnittgrößenkombinationen übertragen können. Die einzelnen Parameter, die dabei untersucht werden sollten, sind im Wesentlichen die Klebefugengeometrie sowie die Oberflächenbeschaffenheit und Bewehrung der zu verklebenden Bauteile. Als Klebstoff sollte in erster Linie ein zementgebundener Hochleistungsmörtel, eingesetzt werden. Das Optimieren der Klebefugengeometrie und der Bewehrung in der Nähe der Fuge erfolgte mit Hilfe eines mathematisch fundierten Shape- und Topologie-Optimierungsverfahrens, wobei die Fugengeometrie sowie das Interface zwischen Beton und Bewehrung mit Level-Set-Funktionen beschrieben wurden. Dieses Verfahren nutzt den topologischen Gradienten als Maß für die Sensitivität der Zielfunktion bzgl. der Größe einer Pore oder eines Risses in einem gegebenen Punkt im Bauteil [1]. Auf der Grundlage von Kleinteilversuchen wurden Bruchkriterien entwickelt, die die Festigkeit der Klebefuge sowohl für eine kombinierte Schub-Druck- als auch für eine Schub-Zugbeanspruchung beschreiben. Basierend auf den gewonnenen Erkenntnissen wurden weiterhin Entscheidungshilfen zur Fugengestaltung sowie ein ingenieurmäßiger Bemessungsansatz erarbeitet. [Aus: Kurzzusammenfassung] / Continuous two-dimensional connections, which are achieved by gluing are particularly suitable for the force-locking and form-fit joining of thin-walled, filigree precast concrete elements. Within the framework of this project, easy-to-handle adhesive joints for plate and plane components can be designed and optimized. The connections should be designed in such a way that they can withstand both stresses from individual internal forces as well as from combinations of internal forces. In essence, the individual parameters that should be investigated are the geometry of the bonding joint as well as the surface condition and reinforcement of the components to be bonded. A cementitious high-performance mortar should primarily be used as adhesive. The optimization of the adhesive joint geometry and the reinforcement close to the joint was carried out by means of a mathematically founded shape and topology optimization method, whereby the joint geometry as well as the interface between concrete and reinforcement were described with level set functions. This method uses the topological gradient as a measure of the sensitivity of the objective function to the size of a pore or crack at a given point in the structural member [1]. On the basis of small part tests, fracture criteria were developed which describe the strength of the adhesive joint both for a combined shear-compressive and a shear-tensile load. Based on the knowledge gained, decision supports for joint design and an engineering design approach were also developed. [Off: Summary]

Structural adhesives are widely used with great success, and yet occasional failures can occur, often resulting from improper bonding procedures or joint design, overload or other detrimental service situations, or in response to a variety of environmental challenges. In these situations, cracks can start within the adhesive layer or debonds can initiate near an interface. The paths taken by propagating cracks can affect the resistance to failure and the subsequent service lives of the bonded structures. The behavior of propagating cracks in adhesive joints remains of interest, including when some critical environments, complicated loading modes, or uncertainties in material/interfacial properties are involved. From a mechanics perspective, areas of current interest include understanding the growth of damage and cracks, loading rate dependency of crack propagation, and the effect of mixed mode fracture loading scenarios on crack path selection. This dissertation involves analytical, numerical, and experimental evaluations of crack propagation in several adhesive joint configurations. The main objective is an investigation of crack path selection in adhesively bonded joints, focusing on in-plane fracture behavior (mode I, mode II, and their combination) of bonded joints with uniform bonding, and those with locally weakened interfaces. When removing cured components from molds, interfacial debonds can sometimes initiate and propagate along both mold surfaces, resulting in the molded product partially bridging between the two molds and potentially being damaged or torn. Debonds from both adherends can sometimes occur in weak adhesive bonds as well, potentially altering the apparent fracture behavior. To avoid or control these multiple interfacial debonding, more understanding of these processes is required. An analytical model of 2D parallel bridging was developed and the interactions of interfacial debonds were investigated using Euler-Bernoulli beam theory. The numerical solutions to the analytical results described the propagation processes with multiple debonds, and demonstrated some common phenomena in several different joints corresponding to double cantilever beam configurations. The analytical approach and results obtained could prove useful in extensions to understanding and controlling debonding in such situations and optimization of loading scenarios. Numerical capabilities for predicting crack propagation, confirmed by experimental results, were initially evaluated for crack behavior in monolithic materials, which is also of interest in engineering design. Several test cases were devised for modified forms of monolithic compact tension specimens (CT) were developed. An asymmetric variant of the CT configuration, in which the initial crack was shifted to two thirds of the total height, was tested experimentally and numerically simulated in ABAQUS®, with good agreement. Similar studies of elongated CT specimens with different specimen lengths also revealed good agreement, using the same material properties and cohesive zone model (CZM) parameters. The critical specimen length when the crack propagation pattern abruptly switches was experimentally measured and accurately predicted, building confidence in the subsequent studies where the numerical method was applied to bonded joints. In adhesively bonded joints, crack propagation and joint failure can potentially result from or involve interactions of a growing crack with a partially weakened interface, so numerical simulations were initiated to investigate such scenarios using ABAQUS®. Two different cohesive zone models (CZMs) are applied in these simulations: cohesive elements for strong and weak interfaces, and the extended finite element method (XFEM) for cracks propagating within the adhesive layer. When the main crack approaches a locally weakened interface, interfacial damage can occur, allowing for additional interfacial compliance and inducing shear stresses within the adhesive layer that direct the growing crack toward the weak interface. The maximum traction of the interfacial CZM appears to be the controlling parameter. Fracture energy of the weakened interface is shown to be of secondary importance, though can affect the results when particularly small (e.g. 1% that of the bulk adhesive). The length of the weakened interface also has some influence on the crack path. Under globally mixed mode loadings, the competition between the loading and the weakened interface affects the shear stress distribution and thus changes the crack path. Mixed mode loading in the opposite direction of the weakened interface is able to drive the crack away from the weakened interface, suggesting potential means to avoid failure within these regions or to design joints that fail in a particular manner. In addition to the analytical and numerical studies of crack path selection in adhesively bonded joints, experimental investigations are also performed. A dual actuator load frame (DALF) is used to test beam-like bonded joints in various mode mixity angles. Constant mode mixity angle tracking, as well as other versatile loading functions, are developed in LabVIEW® for use with a new controller system. The DALF is calibrated to minimize errors when calculating the compliance of beam-like bonded joints. After the corrections, the resulting fracture energies ( ) values are considered to be more accurate in representing the energy released in the crack propagation processes. Double cantilever beam (DCB) bonded joints consisting of 6061-T6 aluminum adherends bonded with commercial epoxy adhesives (J-B Weld, or LORD 320/322) are tested on the DALF. Profiles of the values for different constant mode mixity angles, as well as for continuously increasing mode mixity angle, are plotted to illustrate the behavior of the crack in these bonded joints. Finally, crack path selection in DCB specimens with one of the bonding surfaces weakened was studied experimentally, and rate-dependency of the crack path selection was found. Several contamination schemes are attempted, involving of graphite flakes, silicone tapes, or silane treatments on the aluminum oxide interfaces. In all these cases, tests involving more rapid crack propagation resulted in interfacial failures at the weakened areas, while slower tests showed cohesive failure throughout. One possible explanation of this phenomenon is presented using the rate-dependency of the yield stress (commonly considered to be corresponding to the maximum traction) of the epoxy adhesives. These experimental observations may have some potential applications tailoring adhesive joint configurations and interface variability to achieve or avoid particular failure modes. / Ph. D.