En esta tesis doctoral se presenta el diseño, la implementación y la caracterización de sensores en fibra óptica para la monitorización de diversas magnitudes en ambientes adversos. Se entiende como ambientes adversos aquellas condiciones ambientales externas a los sensores que por su naturaleza dificultan el uso y la fiabilidad a largo plazo de los sistemas de monitorización. Existe una gran variedad de ambientes adversos tales como temperaturas extremas, altas presiones, ambientes químicos o ionizantes, vibraciones o impactos mecánicos, entre otros. Este trabajo de tesis, realizado en el Grupo de Comunicaciones Ópticas y Cuánticas (GCOC) del Instituto de Telecomunicaciones y Aplicaciones Multimedia (ITEAM) de la Universitat Politècnica de València así como el trabajo realizado durante la estancia en la School of Engineering and Applied Science de la Aston University, contempla algunos de estos escenarios, por lo que en el diseño e implementación de los sensores ópticos se han empleado distintas tecnologías ópticas, como las redes de difracción de Bragg (FBGs) o los interferómetros ópticos, con el fin de optimizar las prestaciones de los sensores. En primer lugar, se ha realizado un estudio exhaustivo de las redes de difracción de Bragg regeneradas (RFBGs) para la medida de temperaturas extremas, cercanas a los 1300ºC en algunos casos. Este estudio comprende desde el proceso de fabricación de estos dispositivos fotónicos hasta la caracterización como sensores de temperatura y el estudio de la estabilidad térmica a largo plazo. Se ha realizado también un estudio teórico y experimental sobre la multiplexación de interferómetros modales que, por su sensibilidad y robustez, son muy apropiados para su uso en condiciones ambientales adversas. La técnica de multiplexación desarrollada permite multiplexar los interferómetros modales en distintas configuraciones minimizando la interferencia entre ellos. Por último, se muestra la implementación de un sistema de inscripción de FBGs en fibras ópticas de polímeros y el uso de los dispositivos obtenidos para el diseño, la implementación y la caracterización de sensores ópticos para la medida de curvaturas, grandes deformaciones y deformaciones dinámicas. / Barrera Vilar, D. (2013). Diseño, fabricación y caracterización de FBGs e interferómetros en fibra óptica para la monitorización en ambientes adversos [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/33399 / Premios Extraordinarios de tesis doctorales

[EN] Structural Health Monitoring (SHM) is a discipline that quantitatively assesses the integrity and performance of infrastructures, relying on sensors, and support the development of efficient Maintenance and Rehabilitation (M&R) plans. Optical Multicore Fiber (MCF) Shape Sensors offer an innovative alternative to traditional methods and enable the reconstruction of the deformed shape of structures directly and in real-time, with no need of computation models or visual contact and exploiting all the advantages of Optical Fiber Sensors (OFS) technology. Despite the intense research efforts centered on this topic by research groups worldwide, a comprehensive investigation on the parameters that influence the performance of these sensors has not been conducted yet. The first part of the thesis presents a numerical study that examines the effects of strain measurement accuracy and core position errors on the performance of optical multicore fiber shape sensors in sensing three-dimensional curvature, which is at the basis of shape reconstruction. The analysis reproduces the strain measurement process using Monte Carlo Method (MCM) and identifies several parameters which play a key role in the phenomenon, including core spacing (distance between outer cores and sensor axis), number of cores and curvature measured. Finally, a set of predictive models were calibrated, by fitting the results of the simulations, to predict the sensors performance. Afterward, an experimental study is proposed to evaluate the performance of optical multicore fiber in sensing shape, with particular focus on the influence of strain sensors length. Two shape sensors were fabricated, by inscribing long (8.0 mm) and short (1.5 mm) Fiber Bragg Gratings (FBG) into the cores of a multicore seven-core fiber. Thus, the performance of the two sensors was assessed and compared, at all the necessary phases for shape reconstruction: strain sensing, curvature calculation and shape reconstruction. To conclude, an innovative approach, based on the Saint-Venant's Torsion Theory, is presented to determine the twisting of multicore fiber and to compensate the errors due to twisting during shape reconstruction. The efficiency of the theoretical approach was then corroborated performing a series of twisting tests on a shape sensor, fabricated by inscribing FBGs sensors into an optical spun multicore seven-core fiber. The investigation of the mechanical behavior of multicore optical shape sensors has synergically involved diverse disciplines: Solid Mechanics, Photonics, Statistics and Data Analysis. Such multidisciplinary research has arisen from the prolific cooperation between the Institutes of the Institute of Science and Technology of Concrete (ICITECH) and the Institute of Telecommunications and Multimedia Applications (iTEAM) - Photonics Research Labs (PRL) - of Universitat Politècnica de València (UPV), in addition to valuable collaboration with other members of the European ITN-FINESSE project, to which this work belongs. This research work aims to enhance the performance optical multicore fiber shape sensors and support the development of new sensor geometries, with great potential for structural health monitoring applications. / [ES] La Monitorización de la Salud Estructural (MSE) evalúa cuantitativamente la integridad y el comportamiento de las infraestructuras y permite desarrollar planes eficaces de Mantenimiento y Rehabilitación (M&R), utilizando los datos de los sensores. Sensores de forma basados en fibra óptica multinúcleo ofrecen una alternativa a los métodos tradicionales y permiten la reconstrucción de la deformada de estructuras de forma directa y en tiempo real, sin necesidad de modelos de cálculo o contacto visual y con todas las ventajas de la tecnología de los Sensores de Fibra Óptica (SFO). A pesar de los grandes esfuerzos en la investigación centrada en este tema por parte de los grupos de investigación de todo el mundo, todavía no se ha realizado una investigación exhaustiva que estudie los parámetros que influyen en el comportamiento de estos sensores. En la primera parte de la tesis se presenta un estudio numérico en el que se examinan los efectos de la precisión de la medición de la tensión y los errores de posición del núcleo en el comportamiento de los sensores de forma basados en fibra óptica multinúcleo para definir la curvatura tridimensional, que es la base de la reconstrucción de la forma. El análisis reproduce el proceso de medición de la tensión utilizando el método de Monte Carlo (MC) e identifica una serie de parámetros que desempeñan un papel en el proceso, entre ellos la separación del núcleo (distancia entre los núcleos exteriores y el eje del sensor), el número de núcleos y la curvatura medida. Por último, se calibró un conjunto de modelos de predicción ajustando los resultados de las simulaciones para predecir el comportamiento de los sensores. A continuación, se propone un estudio experimental para evaluar el comportamiento de los sensores de forma basado en fibra óptica multinúcleo, con especial atención en la influencia de la longitud de los sensores de deformación. Se fabricaron dos sensores de forma, inscribiendo Fiber Bragg Gratings (FBG) con longitudes de 8,0 mm y 1,5 mm en los núcleos de una fibra multinúcleo de siete núcleos. Así, se evaluó y comparó el comportamiento de los dos sensores en todas las fases necesarias para la reconstrucción de la forma, incluyendo la medición de la tensión, el cálculo de la curvatura y la reconstrucción de la forma. Para concluir, se presenta un enfoque innovador, basado en la Teoría de la Torsión de Saint-Venant, para determinar la torsión de la fibra multinúcleo y compensar los errores debidos a la torsión durante la reconstrucción de la forma. La eficiencia del enfoque teórico fue verificada realizando una serie de pruebas de torsión en un sensor de forma, fabricado inscribiendo los sensores de FBGs en una fibra óptica multinúcleo torcida y siete núcleos. La investigación del comportamiento mecánico de los sensores ópticos de forma multinúcleo ha involucrado sinérgicamente diversas disciplinas: Mecánica del sólido, Fotónica, Estadística y Análisis de datos. Esta investigación multidisciplinaria ha surgido de la prolífica cooperación entre el Instituto de Ciencia y Tecnología del Hormigón (ICITECH) y el Instituto de Telecomunicaciones y Aplicaciones Multimedia (iTEAM) - Laboratorio de Investigación Fotónica (LIF) - de la Universidad Politécnica de Valencia (UPV), además de la valiosa colaboración con otros miembros del proyecto europeo ITN-FINESSE, al que pertenece este trabajo. Este trabajo de investigación puede permitir mejorar el comportamiento de los sensores de forma basados en fibra óptica multinúcleo y apoyar el desarrollo de nuevas geometrías de sensores, con un gran potencial para aplicaciones de control de la salud estructural. / [CA] Structural Health Monitoring (SHM) avalua quantitativament la integritat i el comportament de les infraestructures i permet desenrotllar plans eficaços de Maintenance and Rehabilitation (M&R), utilitzant les dades dels sensors. Optical Multicore Fiber (MCF) Shape Sensors oferixen una alternativa als mètodes tradicionals i permeten la reconstrucció de la forma de la deformació de les estructures de forma directa i en temps real, sense necessitat de models de càlcul o contacte visual i amb tots els avantatges de l'Optical Fiber Sensors (OFS) Technology. A pesar dels grans esforços en la investigació centrada en aquest tema per part dels grups d'investigació de tot el món, encara no s'ha realitzat una investigació exhaustiva que estudie els paràmetres que influïxen en el comportament d'aquestos sensors. En la primera part de la tesi es presenta un estudi numèric en què s'examinen els efectes de la precisió del mesurament de la tensió i els errors de posició del nucli en el comportament dels sensors de forma basats en fibra òptica multinucli per a definir la curvatura tridimensional, que és la base de la reconstrucció de la forma. L'anàlisi reproduïx el procés de mesurament de la tensió utilitzant el mètode de Monte Carlo (MC) i identifica una sèrie de paràmetres que exercixen un paper en el procés, entre ells la separació del nucli (distància entre els nuclis exteriors i l'eix del sensor), el nombre de nuclis i la mesura de la curvatura. Finalment, es va calibrar un conjunt de models de predicció ajustant els resultats de les simulacions per a predir el comportament dels sensors. A continuació, es proposa un estudi experimental per a avaluar el comportament dels sensors de forma basat en fibra òptica multinucli, amb especial atenció en la influència de la longitud dels sensors de deformació. Es van fabricar dos sensors de forma, inscrivint Fiber Bragg Gratings (FBG) amb longituds de 8,0 mm i 1,5 mm en els nuclis d'una fibra multinucli de set nuclis. Així, es va avaluar i es va comparar el comportament dels dos sensors en totes les fases necessàries per a la reconstrucció de la forma, incloent el mesurament de la tensió, el càlcul de la curvatura i la reconstrucció de la forma. Per a concloure, es presenta un enfocament innovador, basat en la Teoria de la Torsió de Saint-Venant, per a determinar la torsió de la fibra multinucli i compensar els errors deguts a la torsió durant la reconstrucció de la forma. L'eficiència de l'enfocament teòric va ser verificada realitzant una sèrie de proves de torsió en un sensor de forma, fabricat inscrivint els sensors de FBGs en una fibra òptica de set nuclis de filat múltiple. La investigació del comportament mecànic dels sensors òptics de forma multinucli ha involucrat sinèrgicament diverses disciplines: Mecànica del sòlid, Fotónica, Estadística i Anàlisi de dades. Aquesta investigació multidisciplinària ha sorgit de la prolífica cooperació entre l'Institut de Ciència i Tecnologia del Formigó (ICITECH) i l'Institut de Telecomunicacions i Aplicacions Multimèdia (iTEAM) - Laboratori de investigación fotònica (LIF) - de la Universitat Politècnica de València (UPV), a més de la valuosa col·laboració amb altres membres del projecte europeu ITN- FINESSE, al qual pertany aquest treball. Aquest treball d'investigació pot permetre millorar el comportament dels sensors de forma basats en fibra òptica multinucli i ajudar al desenrotllament de noves geometries de sensors, amb un gran potencial per a aplicacions de control de la salut estructural. / Floris, I. (2020). Optical Multicore Fiber Shape Sensors. A numerical and experimental performance assessment [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/148715

[pt] O aumento dos custos relacionados aos processos de manutenção em estruturas como aeronaves, aliadas à crescente demanda das mesmas, alimentam a necessidade de investimentos em técnicas inovadoras de monitoramento estrutural. Dessa forma, o trabalho realizado nesta tese, busca o desenvolvimento de uma técnica de monitoramento ativo, visando o acompanhamento de parâmetros da estrutura analisada, a fim de identificar e caracterizar processos de dano não visíveis, tais como corrosão e delaminação. A metodologia empregada, teve como base a análise dos padrões de deformação superficial, obtidos com o uso de grades de sensores à fibra óptica baseadas em redes de Bragg (FBG). Inicialmente, tais padrões foram provocados por carregamentos estáticos (tração), e posteriormente por atuadores PTZ fixados à estrutura. Estes últimos são submetidos a uma voltagem alternada e frequência fixa. Esta técnica apresenta todas as vantagens dos sensores FBG (massa e dimensões reduzidas, imunidade eletromagnética, elevado poder de multiplexação e alta sensibilidade entre outras), alem de permitir a visualização de alterações nos padrões de deformação, provocados por danos, através da variação da frequência de excitação. Com relação à interpretação dos resultados, a estratégia empregada consistiu em separar o problema de detecção e caracterização dos danos. Dessa forma, a detecção é realizada comparando a energia das deformações superficiais dos corpos de prova nos casos com e sem defeito, enquanto a caracterização é obtida através a utilização de redes neurais artificiais (RNA), por meio de rotinas de reconhecimento de padrões. / [en] The higher costs related to maintenance processes in structures such as aircraft, coupled with the growing demand of them, fueling the need for investment in innovative techniques for structural monitoring. Thus, the work done in this thesis seeks to develop a technique of active monitoring, aiming at monitoring of structure parameters analyzed in order to identify and characterize processes of hidden damage such as corrosion and delamination. The maid methodology was based on the analysis of patterns of surface deformation, obtained with the use of nets of optical fiber sensors based on fiber Bragg gratings ( FBG ). Initially, these patterns were caused by static loads (tension ), and later by PTZ actuators fixed to the frame, who are subjected to an AC voltage and fixed frequency. This technique has all the advantages of the FBG s sensors (mass and small dimensions, electromagnetic immunity, high multiplexing s power and high sensitivity among others), in addition to allowing visualization of changes in the patterns of deformation caused by damage, by varying the frequency excitation. With respect to the interpretation of the results, the strategy employed was to separate the problem of detection and characterization of damage. Thus, the detection is performed by comparing the deformation energy of the surface of the specimens in the cases with and without defect, whereas the characterization is obtained through the use of artificial neural networks (ANN) by means of pattern recognition routines.

Améliorer la sécurité routière passe par une meilleure compréhension des causes d'accidents. Il est donc nécessaire de développer des observatoires discrets pour étudier la manière de conduire de tous les automobilistes. Une partie de cette analyse implique l'utilisation de capteurs mesurant les trajectoires des véhicules sur une portion de route. Deux capteurs innovants ont été crées pour pallier au manque de capteurs suffisamment précis pour ces travaux de recherche : le premier est un capteur à fibres optiques présentant une succession de réseaux de Bragg et le second, protégé par un brevet, est fondé sur une technologie résistive. Le premier repère la déformation locale de fibres optiques noyées à moins d'un centimètre sous la surface de la chaussée. Il utilise la variation de longueurs d'onde engendré par l'extension de la fibre à la zone de contact roue - sol. En utilisant un algorithme adéquat, il est insensible à la température. Le second est constitué de deux conducteurs dont un est résistif. Le poids du véhicule engendre un contact électrique entre les deux conducteurs, transformant la résistance électrique de l'ensemble. Les modèles développés, électrique ainsi que de variation thermique, permettent sa meilleure utilisation. Ils ont été soumis à une expérimentation sur une route départementale. Le capteur optique s'avère plus performant mais coûteux. Le deuxième n'est pas assez robuste mais présente des perspectives intéressantes. / This action stake is not technology for itself. It is a great help the development of new safety functions, e.g. the estimation of driver’s behaviour based uponthe vehicle’s trajectory. This trajectory is determined via two sensors we developed. This system must not disturb the driver and should therefore remain invisible to him. The first one is a fiber Bragg grating (FBG) sensor. It detects local strain due to the vehicle weight. The fiber is embedded in the road thanks to resin used in other traffic sensors. The vehicle location is spotted according to the variations of Bragg wavelengths. The fiber extension located under the ground - wheel contact zone changes the step of the Bragg grating. The second one is based upon two conductors. One of them has a grater electrical resistance. The vehicle’s weight creates a link between the two conductors. The resulting electrical resistance provides a lateral position estimation of the vehicle. Electrical and thermic models and simulation even increase the sensor reliability. A caveat is lodged. Both of them were tested on a secondary road. To put in a nutshell, the FBG sensor gives better results but is very expensive (sensors and interrogator too). The resistance sensor is not much raw nevertheless it has interesting perspectives.

A slab-coupled optical fiber sensor (SCOS) falls into a narrow class of all-dielectric optical fiber electric field sensors, which makes it a perfect candidate for measurements of high electric fields in environments where presence of conductors is highly perturbing to the system under test. Its nonlinear response to high fields requires a new nonlinear calibration technique. A nonlinear calibration method is explained and demonstrated to successfully measure high electric fields, as well as high voltages with dynamic range up to 50 dB. Furthermore, a SCOS can be fitted into narrow spaces and make highly localized measurements due to its small size. This allows a SCOS to be integrated inside a standard high voltage coaxial cable, such as RG-218. Effects of partial discharge and arcing is minimized by development of a fabrication method to avoid introduction of impurities, especially air-bubbles, into the cable during SCOS insertion. Low perturbation of the measured voltage is shown by simulating the introduced voltage reflections to be on the order of –50 dB. It is also shown that a SCOS can be inserted into other cables without significant perturbation to the voltage. A complete high voltage and high electric field measurement system is built based on the high-voltage modifications of the SCOS technology. The coaxial SCOS is enhanced for robustness. Enhancements include packaging a SCOS into stronger ceramic trough, strengthening the fiber with kevlar reinforced furcation tubing and protecting the sensor with metal braces and protective shells. The interrogator is protected from electromagnetic interference with an RF-shielded box. Reduction in power losses introduced by the new PANDA-SCOS technology allows interrogator bandwidths to be increased up to 1.2 GHz. The whole measurement process is streamlined with dedicated software, developed specifically for high voltage and electric field measurements with support for the nonlinear calibration.

A slab-coupled optical fiber sensor (SCOS) falls into a narrow class of all-dielectric optical fiber electric field sensors, which makes it a perfect candidate for measurements of high electric fields in environments where presence of conductors is highly perturbing to the system under test. Its nonlinear response to high fields requires a new nonlinear calibration technique. A nonlinear calibration method is explained and demonstrated to successfully measure high electric fields, as well as high voltages with dynamic range up to 50 dB. Furthermore, a SCOS can be fitted into narrow spaces and make highly localized measurements due to its small size. This allows a SCOS to be integrated inside a standard high voltage coaxial cable, such as RG-218. Effects of partial discharge and arcing is minimized by development of a fabrication method to avoid introduction of impurities, especially air-bubbles, into the cable during SCOS insertion. Low perturbation of the measured voltage is shown by simulating the introduced voltage reflections to be on the order of −50 dB. It is also shown that a SCOS can be inserted into other cables without significant perturbation to the voltage.A complete high voltage and high electric field measurement system is built based on the high-voltage modifications of the SCOS technology. The coaxial SCOS is enhanced for robustness. Enhancements include packaging a SCOS into stronger ceramic trough, strengthening the fiber with kevlar reinforced furcation tubing and protecting the sensor with metal braces and protective shells. The interrogator is protected from electromagnetic interference with an RF-shielded box. Reduction in power losses introduced by the new PANDA-SCOS technology allows interrogator bandwidths to be increased up to 1.2 GHz. The whole measurement process is streamlined with dedicated software, developed specifically for high voltage and electric field measurements with support for the nonlinear calibration.

<p>The task of the project was to evaluate a differential phase shift keying demodulation technique by replacing a Mach-Zehnder interferometer receiver with an optical filter (Fiber Bragg Grating). Computer simulations were made with single optical transmission, multi channel systems and transmission with combined angle/intensity modulated optical signals. The simulations showed good results at both 10 and 40 Gbit/s. Laboratory experiments were made at 10 Gbit/s to verify the simulation results. It was found that the demodulation technique worked, but not with satisfactory experimental results. The work was performed at Eindhoven University of Technology, Holland, within the framework of the STOLAS project at the department of Electro-optical communication.</p>

The task of the project was to evaluate a differential phase shift keying demodulation technique by replacing a Mach-Zehnder interferometer receiver with an optical filter (Fiber Bragg Grating). Computer simulations were made with single optical transmission, multi channel systems and transmission with combined angle/intensity modulated optical signals. The simulations showed good results at both 10 and 40 Gbit/s. Laboratory experiments were made at 10 Gbit/s to verify the simulation results. It was found that the demodulation technique worked, but not with satisfactory experimental results. The work was performed at Eindhoven University of Technology, Holland, within the framework of the STOLAS project at the department of Electro-optical communication.

The objective of this thesis is to study of optical effects, arising in the form of non-uniform waveguide structure, complicated refractive index profiles or due to pulse propagation in dense wavelength division multiplexing (DWDM) optical communication systems. These effects are important and critically influence the performance of DWDM optical systems. A comprehensive survey of current literature on optical effects due to nonuniform optical structure and nonlinear optical effects is first done, showing their advantages and disadvantage in optical communication systems. A survey on methods of optical waveguide analysis is also done. The main contribution has been made to three main aspects of the problem : Accurate analysis of uniform/non-uniform optical waveguides with arbitary refractive index profiles Pulse propagation and distortion in DWDM Raman amplification systems. Use of non-uniform FBG to compensate for pulse distortion We study several existing analytical techniques developed so far for analyzing the mode of non-uniform optical waveguide structures. Later, we verify the analytical results by finite element method (FEM). The convergence study is also carried out. A new computational technique is proposed modifying the finite element method to analyze complex refractive index profiles required for the analysis, namely single mode step index profile, multi clad fiber, W -profile, chirp profile etc. An accuracy of 10−4 in the calculation of propagation constant/eigen-value is demonstrated. Dispersion characteristics of optical fibers w.r.t. different profile parameters is evaluated. A modification to scalar BPM is proposed and applied to study the effects of inhomogeneities along the propagation direction. The applicability and accuracy of the method is tested using integrated optic waveguide devices, namely, graded index slab waveguide. The proposed BPM uses Fourier decomposition of the transverse field. Coupled mode theory (CMT) of optical waveguides in non-homogeneous optical medium is applied to study the interaction of lightwaves propagation together such as in a DWDM system. The BPM results is verified by CMT. The inhomogeneous waveguide theory is extended to study pulse propagation in DWDM optical communication system. Nonlinear optical effects are an important aspects of DWDM systems with fiber Raman amplifier. Finite difference time domain (FDTD) method is necessary to study these nonlinear optical effects as other conventional methods are not suitable here. Here, we discuss DWDM optical communication systems due to nonlinearity in the form of SRS effect. In case of FRA, we study the various kinds of fiber profile design parameters, for the purpose to achieve and extend the flat gain bandwidth over the EDFA window. We also propose and study, a new bi-directional optical fiber transmission scheme with various constraints, using Raman amplification process with and without pump depletion. Our scheme, provides an advantage like high SNR, low pump induced noise, for long-haul communication link. We find that, there is a quite significant crosstalk and power coupling among the dense DWDM channels but earlier discussed BPM fails to account for possible interference effects among the channels. To reduce the harmful nonlinear optical effects like four wave mixing (FWM), we need to deploy a high chromatic dispersion fiber, which will ultimately lead to high pulse walk-off rate among the DWDM channels; hence for high bit rate long haul systems, walk-off effect can not be ignored. Application of FDTD provided an improved insight into the effect of GVD on stimulated Raman scattering crosstalk than different modulation techniques and line codes. It is shown through analysis that pulse walk-off phenomena may distort the data asymmetrically; especially for case of wide-band DWDM transmission system. Hence, the pulse walk-off effect should be considered in future systems containing optical amplifier. It is shown, that large walk-off rate may reduce the crosstalk among DWDM channels but tends to increase the asymmetric pulse distortion. Data may lose due to high walk-off effect. We also investigate channel addition/removal process in DWDM fiber Raman amplifier. We also demonstrate that the pulse walk-off effect tends to lead significantly to positive chirp for higher frequency channels. This feature can be exploited to overcome the chromatic dispersion effects in DWDM transmission systems. Pulse walk-off induced chirp, can be compensated by using the nonuniform fiber Bragg grating (NUFBG). The CMT due to periodic perturbation of the circular cylindrical waveguide structures is applied here. Here, we discuss the function of fiber Bragg grating as a transmission versus reflecting grating filter. We also discuss, FBG application to gain flattening of an EDFA window as well as how the group velocity dispersion (GVD) will be affected with bandwidth and coupling coefficient. We develop a new analytical technique to estimate the bandwidth of FBG based optical system. Finally, we investigate the dispersion compensation properties, pulse distortion, peak reflectivity analysis in uniform/non-uniform FBG due to an uniform/non-uniform incoming signal. More complicated refractive index profile can significantly reduce the GVD as well as side lobes intensity. Dispersion characteristic due to an arbitrary refractive index profile is discussed in details for the case of non-uniform FBG. Thus, we concluded that wide band DWDM optical communication system need to closely take into account various inhomogeneities and nonlinearities of optical fibers w.r.t. wave and pulse propagation.

La corrosion des armatures de renforcement des structures en béton représente un enjeu socio-économique majeur. Sa détection et le suivi de son évolution constituent un défi pour la recherche appliquée. Les techniques standards non destructives de détection de corrosion mettent en œuvre des procédés indirects tels la mesure d’impédance, de potentiels, ou par ultrasons. Leurs capacités d’auscultation sont limitées dans l’espace (notamment en profondeur), leur coût reste élevé dans un contexte de maintenance périodique et elles conduisent à des paramètres d’interprétation complexe. Des progrès sont nécessaires dans la détection et l’analyse fiable de la progression des processus de corrosion. Dans ce travail, nous présentons une nouvelle méthode pour détecter la corrosion et le suivi de son évolution, basée sur l’observation directe des changements intervenant à l’interface fer-béton par Capteur à Fibre Optique (CFO). L'attaque par corrosion de la surface de l'armature dépend de plusieurs paramètres électrochimiques (température, pH, carbonatation, présence de chlorures, contamination biologique, etc.). Deux comportements mécaniques à l'interface fer-béton sont distingués. Dans le premier cas (carbonatation), le produit d'oxydation du métal reste à l'interface et augmente la pression interne, pouvant conduire à la fissuration de la couche de béton extérieure. Dans le second cas (piqures), les ions métalliques sont évacués hors de la structure avec comme conséquence une réduction de section des barres d'armature (affaiblissement du renforcement). Un CFO innovant est proposé dans le but de localiser et quantifier les deux types de corrosion précités. Le principe consiste à observer l’impact direct de la corrosion sur l’état de déformation d’une fibre optique préalablement précontrainte par construction. Deux procédés métrologiques sont étudiés : Bragg et réflectométrie fréquentielle (Optical Frequency-Domain Reflectometry - OFDR). Des tests de corrosion accélérée montrent la faisabilité du procédé. Une procédure de fabrication simplifiée et à coût optimisé est proposée pour la surveillance in situ et répartie des structures de génie civil, dans une perspective future de maintenance conditionnée. / Corrosion of reinforced bars (rebars) in concrete structures remains a major issue in civil engineering works, being its detection and evolution a challenge for the applied research. Usual non-destructive corrosion detection methods involve impedance, potential or ultra-sonic indirect measurements of complex interpretation. Besides, they are restricted to near-surface examinations and the maintenance cost is still high (scheduled maintenance). Many efforts remain to be done to survey the onset and progression of corrosion processes in a reliable way. In this work, we present a new methodology to detect the onset of corrosion and to monitor its evolution, based on the direct observation of rebar–concrete interface changes by the use of an Optical Fiber Sensor (OFS). The corrosion attack over rebar surface depends on several physical, chemical and electrochemical parameters (temperature, pH, presence of chlorides/CO2, biological contamination, etc.). Two types of mechanical behavior and described. In the first case (carbonation), metal oxidation products stay at the interface and increase internal pressure, potentially leading to a crack of the external concrete layer. In the second case (pitting), metal ions are evacuated out of the structure, leading to a reduction of the rebar section (structural weakness). An innovative sensor design is proposed with the purpose of localizing and quantifying the amount of both corrosion types. The basic principle consists in measuring the impact of corrosion over the state of strain of a prestressed optical fiber. Two metrological techniques are used: Fiber Bragg Grating (FBG) and Optical Frequency-Domain Reflectometry (OFDR). Accelerated corrosion tests were performed in electrolytic solutions for both kinds of corrosion types (pitting and carbonation) and provide a proof-of-concept for the technique. A low-cost, simplified manufacturing procedure is proposed with the aim to provide distributed and in situ Structural Health Monitoring (SHM), suitable for future Condition-Based Maintenance (CBM) of civil engineering concrete structures.