Partially coherent interaction of the feedback light with the field in the laser cavity is affirmed with the fiber Bragg grating (FBG) stabilized 980-nm pump lasers, on the contrast of normally accepted totally incoherent state of operation in the “coherence collapse” regime. Coherence parameter y was defined in this paper to identify the fraction of feedback light working coherently. It is shown that y can be determined by fitting the measured power-difference versus pumping-rate curve to the simulation results. Experiments confirm that coherence parameter y decreases while the distance between the FBG and the laser facet increases, and vice versa. While, if the device is kept operating in the “coherence-collapse” regime, y would not change with the amount of feedback. This work will be help to improve the performance of the high power FBG stabilized 980-nm pump laser. / Thesis / Master of Applied Science (MASc)

Telecommunication networks based on optical fiber technology have become a major information-transmission system, satisfying the growing demand for bandwidth due to increased internet traffic and other applications such as video on demand, etc. Fiber Bragg gratings (FBGs), in recent years, have emerged as critical components for enabling high-capacity transmission since their response can be tailored to meet the needs of specific applications. FBGs are currently the focus of intense research interest in both the fiber communications and sensing fields. Optical fiber Bragg grating structures in single-mode fiber (SMFBGs) have been studied extensively since the discovery of photosensitivity in germanium-doped silica fiber. They have been used in numerous applications ranging from wavelength-selective filtering in wavelength-division-multiple-access (WDMA) systems to temperature and strain sensing. To a lesser extent, Bragg gratings in multimode fibers have also received attention because of easy coupling with light sources. Most of the MMFBGs related research work has demonstrated the formation of a Bragg grating in a graded-index MMF and briefly reported the measured transmission spectrum. So far, there are few theoretical studies on Bragg gratings in multimode fibers. In this thesis, we investigate Bragg gratings in multimode optical fibers both theoretically and experimentally. A comprehensive numerical model for MMFBGs has been established and the corresponding computer simulation software (MMFBG simulator combined with mode solver) developed. The optical properties of MMFBGs were systematically studied for the first time using our own MMFBG numerical software package. It effectively assists the design modeling for MMFBG-based optical devices. Bragg gratings in multimode fiber were also investigated experimentally. Our theoretical simulation results show good agreement with experiments and offer the insightful explanations for the underlying physics of the device. First, the guided modes were modeled and simulated for step index multimode fibers and graded index multimode fibers with emphasis on parabolic fiber structure. These are popular, standard and commercially available MM fibers, and employed throughout our experiments. This allows us for the simulation of fiber characteristics such as cut-off wavelength, mode effective index, propagation constants and optical field distribution. It also allows for calculation of mode coupling coefficients by overlap integral between any chosen guided modes. Therefore, it serves as a powerful model for the design and analysis of optical fibers. Second, the generalized MMFBG coupled mode theory formalism is derived. The physical mechanism of the behavior of MMFBGs is studied and discussed. The general solution to the MMF Bragg grating problem is achieved by Runge-Kutta, Newton-Raphson and shooting numerical methods. Our theoretical treatment, in particular, offers the advantages which can deal with not only self-coupling but also more complicated cross-coupling interactions and can solve arbitrary large number of mode coupling problems throughout the entire spectra simultaneously for multimode FBGs, thus allowing for a precise and quantitative study of MMFBGs. Such an intensive multimode fiber Bragg grating physical modeling and simulations have not been reported previously. It provides an effective means for the design and analysis of optical fiber devices based on Bragg gratings. Third, the optical properties of multimode FBGs were studies experimentally. Numerical predications of the grating spectral characteristics under fabrication and experimental condition are calculated. The results of the numerical calculations are compared with experimentally measured spectra of multimode gratings written by ultraviolet irradiation of deuterium-sensitized fiber with grating reflectivities ranging from 78% to 99.39%. Good agreement is obtained between the theoretical simulations and the experimental results. Thus, we provide quantitative explanations for the observed experimental phenomena. These explanations give both physical insight and a more complete understanding of the nature of the interaction between the wave propagation and multimode fiber gratings. Furthermore, the spectral simulation of the actual experiments prepares a theoretical guidance for the advanced experimental investigation and also presents a step toward MMFBG device design. Finally, the optical properties of MMFBGs were also studied theoretically. To our knowledge, this is the first detailed analysis and thorough investigation on grating characteristics in MMF. It is demonstrated that the transmission and reflection spectra of fiber Bragg gratings in multimode optical fibers strongly depend on the length of grating, index modulation, period of grating, mode excitation condition and physical structure of MMF. The simulation results allow us to deeply comprehend and visualize the more sophisticated behavior within a multimode fiber grating, and will also allow us to confidently predict and evaluate the performance of more complex structure MMFBGs. It provides the fundamental principles for designing the targeted spectrum performance and settles the theoretical rationale for realizing the practical applications. Overall, the comprehensive numerical model and MMFBG solver package developed in this thesis opens a clear and broad window for understanding MMFBG mechanisms from the physical point of view. Various simulation results and spectral characteristics have been researched and discussed under both ideal and experimental conditions for the purpose of experimental analysis and device design. The results of our study indicate that a new class of potential applications based on MMFBGs can be expected in optical fiber sensors and advanced communication systems. / Thesis / Master of Applied Science (MASc)

The continued growth of the communications industry has caused interest in mode-division multiplexing (MDM) techniques to flourish in recent years. These techniques allow individual waveguide modes to be used as distinct channels. However, as with any versatile technique, it should be also useful and beneficial to extend its application to other areas. This work concerns itself with an initial conceptual design of a mode-division multiplexing (MDM) enabled optical sensor network that can use modes to interrogate either specific sensors or sensor subsystems, and specifically with quanitizing and optimizing the injection and detection of the signal of interest. A hypothetical test setup is demonstrated, and the major issue of back reflection burying the intended signal is addressed, analyzed, and improved. Improvements in the signal-to-background contrast ratio (SBCR) of approximately 10dB were achieved depending on fibre type and proximal face. Suggestions for extensions to further improve the SBCR as well as for applications of this system are discussed. / Master of Science

Invention of silica based optical fiber not only led to revolution in communication but also provided fundamental basis for many research areas. One example area is distributed optical fiber sensing, which has been attracting research interests for decades. Optical fiber sensors are immune to electromagnetic interference, and resistant to corrosion and can endure harsh environment so they have found applications such as structural health monitoring, intrusion detection and oil downhole measurement. Significant research efforts have been paid to fiber sensing area, many techniques have been developed and some of them have been successfully demonstrated, however achieving both high-speed and long-range is still under intensive research. This dissertation proposes and demonstrates a technique with the capability of simultaneous long-range and high-speed sensing by employing serial ultra-weak fiber Bragg gratings (UW-FBGs) and dispersive components. Various factors which have influence on the system performance, including wavelength resolution, spatial resolution and sensing rate, are analyzed. Different types of light sources and dispersive units were designed and a sensing system was built. With this system, both static and dynamic response were measured, and a sensing link consisting of more than 2000 UW-FBGs was successfully measured at the speed of 20kHz. The noise sources of the system were also theoretically analyzed and experimentally measured. This demonstrated sensing technique can be applied to long range temperature and strain sensing. / Ph. D. / Optical fiber is a thin glass rod with normally two layers of slightly different silica. Because of its low loss, optical fiber can guide light for a long distance without causing significant signal fading. Modifications can be made to a small section of an optical fiber to form a fiber Bragg grating, whose optical characteristics are dependent on its temperature or the strain applied to it. This dissertation proposes a technique with the ability of measuring the temperature or strain of a long length of optical fiber which has large quantity of fiber Bragg gratings fabricated in it. Along with the capability of long range sensing, this technique also has high sensing speed. It has been demonstrated that the sensing system could perform measurement in every 50µs when the optical fiber has about 2000 fiber Bragg gratings in it. The resolution, if converted to temperature, is about 1.5°C and the accuracy is 2°C. With the ability of monitoring temperature or strain of a large span at high speed, this technique could be used in areas such as civil structure and air craft health monitoring, instruction detection and high speed temperature monitoring.

No description available.

Bragg grating reflectors etched in amorphous silicon overlay films have been integrated with Ti:LiNbO3 optical waveguides. With a 12.5 mm long grating segment and an etch depth of ~ 93 nm in a 105 nm-thick silicon film, a narrow (0.05 nm) spectral bandwidth with a record high transmission dip (> 20 dB) was achieved at a wavelength of ~1542 nm for TE polarization on an x-cut, y-propagating substrate. The reflectance in the channel waveguides is found to be strongly dependent on the depth of the etched grating. The 3-dB bandwidth of 0.05 nm obtained for all tested samples is the smallest reported for waveguides in LiNbO3. The effect of the Bragg waveguide loss factor on the transmittance and reflectance spectra is investigated using a model for contra-directional coupling that includes an attenuation coefficient. The Bragg grating spectral characteristics are exploited to fabricate distributed Bragg feedback modulators (DBFM) and Bragg reflector Fabry-Perot modulators (BFPM). The sharp cut-off in transmission and reflection spectra, which is an inherent characteristic of Bragg grating, was tuned by applying voltage via the linear electrooptic effect, to produce intensity modulation. The Bragg grating based modulators consume less electric power compared to polarization intensity modulators (PIMs). The DBFM demonstrates 1/1.6 times the modulating voltage of a PIM with identical waveguide and electrode structure. The BFPM shows 1/3.3 times the modulating voltage of the PIM. No difference in the frequency response is observed among the three modulators. Comparison of the modulation sensitivity in the linear region indicates that the Bragg grating based modulators provide better sensitivity than that of the PIM with identical waveguide and electrode structure. These results indicate the potential advantage of the Bragg grating based modulators for enhanced modulation efficiency over conventional modulators. Further improvements can be expected from the optimization of the electrode design.

This thesis concerns various aspects of the durability offibre optic sensors embedded in composite. Since repair orreplacement of embedded sensors is not generally possible, thefunctional reliability of embedded sensors is one of the mostimportant prerequisites for successful use. The main researchobjective was to investigate the interaction between the sensorand the composite, and how this is affecting the mechanical andoptical sensor response. Fibre optic sensors embedded incomposite structures induce local stress concentrations whenthe composite is subjected to mechanical loads andenvironmental changes such as temperature and moisture. Acomplex transfer of stresses through the interfaces between theembedded sensor and the composite occurs and can result inlarge local stresses in the composite and a significant changein the response of the embedded sensor. These stressconcentrations make the interfaces susceptible todebonding. The sensor performance was studied experimentally andnumerically. Some basic results were generated for the EFPI andBragg grating sensors. The phase-strain response was determinedduring static and fatigue loading. The results showed that thesensors were more reliable in compression than in tensilestatic and fatigue loading. Generally, the sensor reliabilityduring loading was significantly improved for the Bragg gratingsensors over that of the EFPI sensor, as an effect of thesensor geometry. This was also demonstrated in theinvestigations on impacts. Impacts do not necessarily result indamage in the composite, but might cause debonding or otherfailure modes in the sensor area. Large, local stressconcentrations occur at several positions in the EFPI sensor,which pointed out that this sensor type was not suitable forembedded applications. The shift in focus from the sensor concept based on the EFPIsensor to that based on the Bragg grating sensor manifesteditself in several studies. The calculated deformation fieldaround an embedded optical fibre was verified in experimentsusing a high-resolution moiré interferometric technique.Furthermore, the improvement in the coating technology wasverified. A significant higher interfacial strength wasobtained with the silane-treated glass surface. The resultsindicated that at least a twofold improvement of the shearstrength was obtained. To simultaneously measure the in-plane strain components andthe temperature change, embedded Bragg grating sensors werearranged in a rosette configuration. The relationship betweenthe optical response from each sensor and the strains in thelaminate was numerically and analytically established. Damage lead to stress redistribution in the sensor region,which may influence the output from the embedded Bragg gratingsensor. The effect was numerically evaluated for interfacialdamage, and was compared to that of a sensor with undamagedinterface. The results showed that debonding might have asignificant influence, in particular for combined thermal andmechanical loading. <b>Keywords</b>: composites, fibre optic sensor, embedded, EFPIsensor, Bragg grating sensor, durability, fatigue, impact,strain measurement, interface, stress analysis

Theoretical and experimental studies of real-time interrogation of fiber Bragg grating (FBG) sensors based on chirped pulse compression with increased interrogation resolution and signal-to-noise ratio are presented. Two interrogation systems are proposed in this thesis. In the first interrogation system, a linearly chirped FBG (LCFBG) is employed as the sensing element. By incorporating the LCFBG in an optical interferometer as the sensor encoding system, employing wavelength-to-time mapping and chirped pulse compression technique, the correlation of output microwave waveform with a chirped reference waveform would provide an interrogation result with high speed and high resolution. The proposed system can provide an interrogation resolution as high as 0.25 μ at a speed of 48.6 MHz. The second interrogation system is designed to achieve simultaneous measurement of strain and temperature. In this system, a high-birefringence LCFBG (Hi-Bi LCFBG) is employed as a sensing element.

Theoretical and experimental studies of real-time interrogation of fiber Bragg grating (FBG) sensors based on chirped pulse compression with increased interrogation resolution and signal-to-noise ratio are presented. Two interrogation systems are proposed in this thesis. In the first interrogation system, a linearly chirped FBG (LCFBG) is employed as the sensing element. By incorporating the LCFBG in an optical interferometer as the sensor encoding system, employing wavelength-to-time mapping and chirped pulse compression technique, the correlation of output microwave waveform with a chirped reference waveform would provide an interrogation result with high speed and high resolution. The proposed system can provide an interrogation resolution as high as 0.25 μ at a speed of 48.6 MHz. The second interrogation system is designed to achieve simultaneous measurement of strain and temperature. In this system, a high-birefringence LCFBG (Hi-Bi LCFBG) is employed as a sensing element.

Bragg grating reflectors etched in amorphous silicon overlay films have been integrated with Ti:LiNbO3 optical waveguides. With a 12.5 mm long grating segment and an etch depth of ~ 93 nm in a 105 nm-thick silicon film, a narrow (0.05 nm) spectral bandwidth with a record high transmission dip (> 20 dB) was achieved at a wavelength of ~1542 nm for TE polarization on an x-cut, y-propagating substrate. The reflectance in the channel waveguides is found to be strongly dependent on the depth of the etched grating. The 3-dB bandwidth of 0.05 nm obtained for all tested samples is the smallest reported for waveguides in LiNbO3. The effect of the Bragg waveguide loss factor on the transmittance and reflectance spectra is investigated using a model for contra-directional coupling that includes an attenuation coefficient. The Bragg grating spectral characteristics are exploited to fabricate distributed Bragg feedback modulators (DBFM) and Bragg reflector Fabry-Perot modulators (BFPM). The sharp cut-off in transmission and reflection spectra, which is an inherent characteristic of Bragg grating, was tuned by applying voltage via the linear electrooptic effect, to produce intensity modulation. The Bragg grating based modulators consume less electric power compared to polarization intensity modulators (PIMs). The DBFM demonstrates 1/1.6 times the modulating voltage of a PIM with identical waveguide and electrode structure. The BFPM shows 1/3.3 times the modulating voltage of the PIM. No difference in the frequency response is observed among the three modulators. Comparison of the modulation sensitivity in the linear region indicates that the Bragg grating based modulators provide better sensitivity than that of the PIM with identical waveguide and electrode structure. These results indicate the potential advantage of the Bragg grating based modulators for enhanced modulation efficiency over conventional modulators. Further improvements can be expected from the optimization of the electrode design.