Spelling suggestions: "subject:"braquetes"" "subject:"raquetes""
71 |
Efeito de cobertura antiaderente no acúmulo de biofilme em dispositivos ortodônticos / Effect of accumulation of coverage nonstick biofilm on orthodontic bracketsOliveira, Adauê Siegert de 01 June 2012 (has links)
Made available in DSpace on 2014-08-20T14:30:05Z (GMT). No. of bitstreams: 1
tese_Adaue_banca.pdf: 296840 bytes, checksum: 0cd98d8b2ca7a1306c82e4b8319d9e71 (MD5)
Previous issue date: 2012-06-01 / The use of orthodontic devices has been associated with an increase in dental biofilm retention. In this study, the effect of hydrophobic coatings, based on (fluorinated or not) organo-silanes, on the reduction of the contact angle and early biofilm retention in orthodontic devices was tested. Two different types of hydrophobic were tested: hydrophobic solution 1 (SH1), obtained by dilution of 2.5% of hexadecyl-triethoxy-silane in ethanol, and hydrophobic solution 2 (SH2), composed of 2.5% of perfluorodecyl-triethoxy-silane diluted in dimethyl sulfoxide. The solutions were applied in ceramic and stainless steel substrates and, via sol-gel process and crosslinking, siloxane networks were formed on the surface of the devices. The effect of the coatings was evaluated in two stages. In the first stage, aiming the characterization of the surface, the water contact angle was analyzed. Stainless steel and polycrystalline alumina plates were prepared, previously applying or not alumina sandblasting as surface treatment. A significant increase in contact angle was observed with the application of both hydrophobic solutions in both substrates, with the sandblasting allowing formation of super-hydrophobic surface in the ceramic substrate (contact angle up to 155o), while hydrophobic surfaces were obtained in the steel substrate (contact angle up to 123o). In the second phase, the effect of the hydrophobic coating on the biofilm retention in orthodontic brackets was evaluated using a microscosm model. Orthodontic brackets were previously prepared according to the surface treatments that showed the best results in the phase 1 (SH1 for steel, SH2 for ceramic). The effect of the coatings on the biofilm formation was evaluated in periods of 12h and 24h (controls: uncoated substrates and sandblasted substrates). The results showed that the hydrophobic coatings did not result in significant effect in biofilm retention for the time 12h, whereas all coating treatments significantly reduced the biofilm retention in the metal and ceramic brackets compared with the control groups. A significant exponential reduction in biofilm retention at 24h was associated with the increase in contact angle. It can be concluded that application of (super)-hydrophobic crosslinked coatings via sol-gel process on the surface of orthodontic metal and ceramic brackets reduced the surface wetting of the surfaces in contact with water and had a significant effect on the retention of dental biofilm after 24h / O uso de dispositivos ortodônticos tem sido associado ao aumento da retenção de biofilme dentário. Neste estudo, foi testado o efeito de coberturas hidrófobas,baseadas em organo-silanos (flourados ou não), no aumento do ângulo de contato e redução de acúmulo de biofilme inicial em dispositivos ortodônticos. Dois tipos diferentes de soluções hidrófobas foram testadas: solução hidrófoba 1 (SH1), obtida
pela diluição de 2,5% de hexadecil-trietóxi-silano em etanol, e solução hidrófoba 2 (SH2), composta por 2,5% de perfluorodecil-trietóxi-silano diluído em dimetilsulfóxido. As soluções foram aplicadas em substratos cerâmico e de aço inox e, via processo sol-gel e reticulação, foram formadas redes siloxanas na superfície dos dispositivos. O efeito das coberturas foi avaliado em duas etapas. Na primeira
etapa, buscando a caracterização da superfície, foi analisado o ângulo de contato com água. Placas de aço inox e alumina policristalina foram preparadas, aplicando ou não jateamento prévio das superfícies com partículas de alumina. Foi observado aumento significativo do ângulo de contato com a aplicação das duas soluções hidrófobas em ambos substratos, sendo que o jateamento do substrato propiciou a
formação de superfície superhidrófoba no substrato cerâmico (ângulo de contato de até 155o), enquanto superfícies hidrófobas foram obtidas no substrato aço (ângulo de contato até 123o). Na segunda fase do trabalho, avaliou-se o efeito da cobertura no acúmulo de biofilme em braquetes ortodônticos, através de modelo de microcosmos. Braquetes ortodônticos foram previamente preparados conforme os tratamentos de superfície que apresentaram melhores resultados na primeira fase (SH1 para aço, SH2 para cerâmica). Foi avaliado o efeito da cobertura na formação de biofilme em períodos de 12h e 24h (controles: substratos não-recobertos e substratos jateados). Os resultados mostraram que as coberturas hidrófobas não resultaram em efeito significativo no acúmulo de biofilme no tempo 12h, entretanto todos os tratamentos de cobertura reduziram de forma significativa o acúmulo de
biofilme sobre os braquetes metálicos e cerâmicos comparados aos grupos controle no período 24h. Foi observada relação de redução exponencial significativa entre ângulo de contato e acúmulo de biofilme para o tempo 24h. Dessa forma, conclui-se
que a aplicação de coberturas (super)-hidrófobas reticuladas via processo sol-gel na superfície de dispositivos ortodônticos metálicos e cerâmicos reduziu o molhamento das superfícies em contato com a água e teve efeito significativo na retenção de biofilme bucal sobre esses dispositivos após 24h
|
72 |
Análise dentária tridimensional em pacientes biprotrusos submetidos a extrações de primeiros pré-molares /Cunha, Anderson Farias da January 2018 (has links)
Orientador: Luiz Gonzaga Gandini Júnior / Resumo: Objetivo: Avaliar as alterações dentárias em indivíduos biprotrusos submetidos a extração dos quatro primeiros pré-molares. Materiais e métodos: A amostra constituise de 50 pacientes adultos Classe I de Angle, biprotrusos, com apinhamento até 4mm por arco dentário e com necessidade de extração de quatro primeiros pré-molares, que foram randomizados em 2 técnicas de tratamento: a retração em massa (n = 25) e a retração em duas etapas (n = 25, cada paciente teve colado um braquete convencional ou autoligado em cada canino de forma aleatória). Foram usados modelos digitais obtidos antes, um, dois e três meses após o início da retração dos caninos, e após o fechamento dos espaços das extrações. Foram avaliados a inclinação, angulação e rotação dos caninos (durante a retração dos caninos), e a rotação dos primeiros molares superiores (na retração em massa ou duas etapas). Resultados: Nenhuma diferença foi encontrada entre a técnica de retração ou tipo de braquete. Conclusão: Conclui-se que não houve diferença na angulação, inclinação e rotação entre os braquetes convencionais ou autoligados, além disso a rotação dos molares foi similar na retração em massa e duas etapas. / Abstract: Objetive: To evaluate the dental changes in patients bimaxillary protrusion with firstpremolar extraction. Methods: Fifty adults patients Class I malocclusion, dentalprotrusion, arch length discrepancy bellow for 4mm, and need for first premolarextractions were randomized to 2 treatment techniques: en-mass retraction (n = 25)and two-steps retraction (n = 25, patients had either conventional or self-ligatingbrackets bonded to canines randomly). Digital models before, and one, two, threemonths after starting the canine retraction, and after the closing of space. Wereevaluated the canine inclination, angulation and rotation (canine retraction), androtation of the upper first molars (en-mass or two-steps retraction). Results: Nodifferences were found between retraction techniques or the type of bracket.Conclusions: Angulation, inclination and rotation showed no diferences betweenconventional or self-ligating brackets, besides that the rotation molar was similar in enmassor two-steps retraction. / Mestre
|
73 |
Forças, momentos e coeficiente de atrito em teste de três pontos e em teste de resistência ao deslizamento com braquetes autoligáveis e fios 0.014\" utilizando um novo dispositivo / Forces, moments and coefficient of friction in three-bracket bending test and in resistance to sliding test with self-ligating brackets and wires 0.014\'\' using a new deviceFreitas, Ana Carolina Carneiro de 26 January 2016 (has links)
O objetivo principal do estudo é comparar o teste em 3 pontos com braquetes com o teste de resistência ao deslizamento utilizando um novo dispositivo que realiza a mensuração simultânea do coeficiente de atrito, das forças e dos momentos nos braquetes de ancoragem e da força de desativação no braquete desalinhado, exercidos por fios ortodônticos. Os objetivos secundários foram desenvolver o dispositivo e comparar, no teste em 3 pontos: (i) a influência, nas grandezas e no coeficiente de atrito cinético, da variação da simetria nas distâncias inter-braquetes, do tipo de braquete de ancoragem (canino ou 2º pré-molar), do deslocamento (3 ou 5mm) do braquete central, do sentido do desalinhamento (vestibular ou lingual) do braquete central e da marca de fio-braquete; (ii) as 3 formas de cálculo do coeficiente de atrito cinético; (iii) os 10 ciclos, para vestibular ou lingual, para verificar se eles são semelhantes ou não entre si. Foram utilizados braquetes autoligáveis (dentes 13, 14 e 15) e fios 0.014\'\' NiTi e CuNiTi das marcas Aditek e Ormco. O teste de resistência ao deslizamento foi realizado no desalinhamento lingual, nos dois deslocamentos e na configuração simétrica. O teste em 3 pontos com braquetes foi realizado no desalinhamento lingual e vestibular, nos dois deslocamentos e na configuração simétrica e assimétrica. Por meio da ANOVA, foram comparados, entre os dois tipos de teste: (A) as grandezas e o coeficiente de atrito e (B) o coeficiente de atrito gerado apenas no braquete de 2º pré-molar. Utilizando-se do mesmo teste estatístico foram comparados, no teste em 3 pontos com braquetes: (A) na configuração simétrica, algumas grandezas e o coeficiente de atrito advindos da variação da marca de fio-braquete, do deslocamento, do desalinhamento e do tipo de braquete; (B) algumas grandezas e o coeficiente de atrito gerados na configuração simétrica e assimétrica; (C) os valores das 3 formas de cálculo do coeficiente de atrito na configuração simétrica; e (D) algumas grandezas e o coeficiente de atrito encontrados nos 10 ciclos. Resultados: (A) a maioria dos valores das grandezas e do coeficiente de atrito gerados pelos dois tipos de teste foram diferentes estatisticamente; (B) o braquete de 2º pré-molar apresentou valores de coeficiente de atrito diferentes entre os dois tipos de teste; (C) na configuração simétrica, as variáveis foram estatisticamente significantes na maioria dos casos para as grandezas analisadas e para o coeficiente de atrito; (D) houve diferença entre a configuração simétrica e assimétrica; (E) o coeficiente de atrito baseado nas duas normais e na força de atrito se aproximou mais da realidade clínica e foi sensível à variação da geometria da relação fio-braquete; e (F) os 10 ciclos para lingual foram semelhantes entre si em 70% dos casos e os 10 ciclos para vestibular foram diferentes em 57% dos casos. Conclusões: o teste em 3 pontos com braquetes é diferente do teste de resistência ao deslizamento; a variação das configurações geométricas e da marca de fio-braquete pode influenciar nos valores das grandezas e do coeficiente de atrito cinético; os 10 ciclos para lingual foram mais semelhantes entre si que os 10 ciclos para vestibular. / The main objective of the study is to compare the three-bracket bending test with the resistance to sliding test using a new device that performs simultaneous measurement of coefficient of friction, the forces and moments on the anchor brackets and deactivation force in misaligned bracket, exercised by orthodontic wires. Secondary objectives were to develop the device and compare, in the three-bracket bending test: (i) the influence, on the physical quantities and on the kinetic friction coefficient, of the variation of the symmetry in the inter-bracket distance, of the type of anchor bracket (canine or 2nd premolar), of displacement (3 or 5mm) and misalignment (buccal or lingual) of the central bracket, and of the wire and bracket brand; (ii) the three ways to calculate the coefficient of kinetic friction; (iii) the 10 cycles, for buccal or lingual, to see if they are similar or not. Self-ligating brackets were used (teeth 13, 14 and 15) and wires 0.014 \'\' NiTi and CuNiTi of Aditek and Ormco brands. The resistance to sliding test was conducted on the lingual misalignment, on both displacements and on symmetrical configuration. The three-bracket bending test was held at the lingual and vestibular misalignment, at both displacements and at the symmetrical and asymmetrical configuration. Through ANOVA, were compared, between the two types of tests: (A) the quantities and the coefficient of friction and (B) the coefficient of friction generated only in the second premolar bracket. Using the same statistical test were compared, in three-bracket bending test: (A) in symmetrical configuration, the quantities and the coefficient of friction arising from the variation in the wire and bracket brands, displacement, misalignment and the type of bracket; (B) the quantities and the coefficient of friction generated by the symmetric and asymmetric configuration; (C) the values of the three ways of calculating friction coefficient; and (D) the quantities and the coefficient of friction encountered in 10 cycles. Results: (A) most of the values of the quantities and the coefficient of friction generated by the two types of test were statistically different; (B) the 2nd premolar bracket showed different friction coefficient values between the two types of test; (C) in the symmetrical configuration, the variables were statistically significant in the most of cases for quantities and the friction coefficient; (D) was found difference between symmetric and asymmetric configuration; (E) the friction coefficient based on both normal forces and frictional force was closer to the clinical reality and was sensitive to variations in the geometry of the wire-bracket relationship; and (F) the 10 cycles for lingual were similar in 70% of cases and the 10 cycles for buccal desalignment were different in 57% of cases. Conclusions: The three-bracket bending test is different from the resistance to sliding test; the variation of geometric configurations and wire and bracket brands may influence the values of the quantities and the coefficient of kinetic friction; the 10 cycles for lingual were more similar to each other than the 10 cycles for buccal.
|
74 |
Forças, momentos e coeficiente de atrito em teste de três pontos e em teste de resistência ao deslizamento com braquetes autoligáveis e fios 0.014\" utilizando um novo dispositivo / Forces, moments and coefficient of friction in three-bracket bending test and in resistance to sliding test with self-ligating brackets and wires 0.014\'\' using a new deviceAna Carolina Carneiro de Freitas 26 January 2016 (has links)
O objetivo principal do estudo é comparar o teste em 3 pontos com braquetes com o teste de resistência ao deslizamento utilizando um novo dispositivo que realiza a mensuração simultânea do coeficiente de atrito, das forças e dos momentos nos braquetes de ancoragem e da força de desativação no braquete desalinhado, exercidos por fios ortodônticos. Os objetivos secundários foram desenvolver o dispositivo e comparar, no teste em 3 pontos: (i) a influência, nas grandezas e no coeficiente de atrito cinético, da variação da simetria nas distâncias inter-braquetes, do tipo de braquete de ancoragem (canino ou 2º pré-molar), do deslocamento (3 ou 5mm) do braquete central, do sentido do desalinhamento (vestibular ou lingual) do braquete central e da marca de fio-braquete; (ii) as 3 formas de cálculo do coeficiente de atrito cinético; (iii) os 10 ciclos, para vestibular ou lingual, para verificar se eles são semelhantes ou não entre si. Foram utilizados braquetes autoligáveis (dentes 13, 14 e 15) e fios 0.014\'\' NiTi e CuNiTi das marcas Aditek e Ormco. O teste de resistência ao deslizamento foi realizado no desalinhamento lingual, nos dois deslocamentos e na configuração simétrica. O teste em 3 pontos com braquetes foi realizado no desalinhamento lingual e vestibular, nos dois deslocamentos e na configuração simétrica e assimétrica. Por meio da ANOVA, foram comparados, entre os dois tipos de teste: (A) as grandezas e o coeficiente de atrito e (B) o coeficiente de atrito gerado apenas no braquete de 2º pré-molar. Utilizando-se do mesmo teste estatístico foram comparados, no teste em 3 pontos com braquetes: (A) na configuração simétrica, algumas grandezas e o coeficiente de atrito advindos da variação da marca de fio-braquete, do deslocamento, do desalinhamento e do tipo de braquete; (B) algumas grandezas e o coeficiente de atrito gerados na configuração simétrica e assimétrica; (C) os valores das 3 formas de cálculo do coeficiente de atrito na configuração simétrica; e (D) algumas grandezas e o coeficiente de atrito encontrados nos 10 ciclos. Resultados: (A) a maioria dos valores das grandezas e do coeficiente de atrito gerados pelos dois tipos de teste foram diferentes estatisticamente; (B) o braquete de 2º pré-molar apresentou valores de coeficiente de atrito diferentes entre os dois tipos de teste; (C) na configuração simétrica, as variáveis foram estatisticamente significantes na maioria dos casos para as grandezas analisadas e para o coeficiente de atrito; (D) houve diferença entre a configuração simétrica e assimétrica; (E) o coeficiente de atrito baseado nas duas normais e na força de atrito se aproximou mais da realidade clínica e foi sensível à variação da geometria da relação fio-braquete; e (F) os 10 ciclos para lingual foram semelhantes entre si em 70% dos casos e os 10 ciclos para vestibular foram diferentes em 57% dos casos. Conclusões: o teste em 3 pontos com braquetes é diferente do teste de resistência ao deslizamento; a variação das configurações geométricas e da marca de fio-braquete pode influenciar nos valores das grandezas e do coeficiente de atrito cinético; os 10 ciclos para lingual foram mais semelhantes entre si que os 10 ciclos para vestibular. / The main objective of the study is to compare the three-bracket bending test with the resistance to sliding test using a new device that performs simultaneous measurement of coefficient of friction, the forces and moments on the anchor brackets and deactivation force in misaligned bracket, exercised by orthodontic wires. Secondary objectives were to develop the device and compare, in the three-bracket bending test: (i) the influence, on the physical quantities and on the kinetic friction coefficient, of the variation of the symmetry in the inter-bracket distance, of the type of anchor bracket (canine or 2nd premolar), of displacement (3 or 5mm) and misalignment (buccal or lingual) of the central bracket, and of the wire and bracket brand; (ii) the three ways to calculate the coefficient of kinetic friction; (iii) the 10 cycles, for buccal or lingual, to see if they are similar or not. Self-ligating brackets were used (teeth 13, 14 and 15) and wires 0.014 \'\' NiTi and CuNiTi of Aditek and Ormco brands. The resistance to sliding test was conducted on the lingual misalignment, on both displacements and on symmetrical configuration. The three-bracket bending test was held at the lingual and vestibular misalignment, at both displacements and at the symmetrical and asymmetrical configuration. Through ANOVA, were compared, between the two types of tests: (A) the quantities and the coefficient of friction and (B) the coefficient of friction generated only in the second premolar bracket. Using the same statistical test were compared, in three-bracket bending test: (A) in symmetrical configuration, the quantities and the coefficient of friction arising from the variation in the wire and bracket brands, displacement, misalignment and the type of bracket; (B) the quantities and the coefficient of friction generated by the symmetric and asymmetric configuration; (C) the values of the three ways of calculating friction coefficient; and (D) the quantities and the coefficient of friction encountered in 10 cycles. Results: (A) most of the values of the quantities and the coefficient of friction generated by the two types of test were statistically different; (B) the 2nd premolar bracket showed different friction coefficient values between the two types of test; (C) in the symmetrical configuration, the variables were statistically significant in the most of cases for quantities and the friction coefficient; (D) was found difference between symmetric and asymmetric configuration; (E) the friction coefficient based on both normal forces and frictional force was closer to the clinical reality and was sensitive to variations in the geometry of the wire-bracket relationship; and (F) the 10 cycles for lingual were similar in 70% of cases and the 10 cycles for buccal desalignment were different in 57% of cases. Conclusions: The three-bracket bending test is different from the resistance to sliding test; the variation of geometric configurations and wire and bracket brands may influence the values of the quantities and the coefficient of kinetic friction; the 10 cycles for lingual were more similar to each other than the 10 cycles for buccal.
|
75 |
EFEITO DA DENSIDADE DE ENERGIA DE FOTOATIVADORES DE ALTA POTÊNCIA NAS PROPRIEDADES FÍSICO-MECÂNICAS DE UMA RESINA ORTODÔNTICAArana, Andrés Fernando Montenegro 16 October 2017 (has links)
Submitted by Angela Maria de Oliveira (amolivei@uepg.br) on 2018-03-01T13:44:47Z
No. of bitstreams: 2
license_rdf: 811 bytes, checksum: e39d27027a6cc9cb039ad269a5db8e34 (MD5)
Andrés Fernando Montenegro.pdf: 11976346 bytes, checksum: fa909dec838336e8c5a4ed73180bb65b (MD5) / Made available in DSpace on 2018-03-01T13:44:47Z (GMT). No. of bitstreams: 2
license_rdf: 811 bytes, checksum: e39d27027a6cc9cb039ad269a5db8e34 (MD5)
Andrés Fernando Montenegro.pdf: 11976346 bytes, checksum: fa909dec838336e8c5a4ed73180bb65b (MD5)
Previous issue date: 2017-10-16 / O objetivo deste estudo foi verificar o efeito da densidade de energia e o tempo de
exposição de fotopolimerizadores LED de terceira geração em uma resina ortodôntica
disponível comercialmente nos valores de microdureza, cisalhamento, índice de
remanescente de resina e grau de conversão. Para tanto, foram realizados 3
experimentos: Experimento 1, o objetivo foi avaliar o grau de conversão (DC) e
microdureza vickers (MHV) da resina ortodôntica utilizando dois LEDs de terceira
geração, assim como, protocolos de fotoativação diferentes. Foram necessários 80
brackets cerâmicos e 80 brackets metálicos, sendo divididos em 16 grupos
experimentais (n=10) tendo os seguintes grupos para cada LED: um grupo controle,
diminuição da metade do tempo de exposição do grupo controle, um quarto do tempo
do grupo controle, função turbo ou plasma para os LEDs Bluephase e Valo,
respetivamente. Imediatamente após a polimerização, foram realizados os ensaios de
DC e MHV. O experimento 2, objetivou verificar a influência de diferentes densidades
de energia emitidas por dois fotoativadores LED de alta potência nas propriedades
físicas e mecânicas de uma resina ortodôntica em brackets metálicos. Foram necessários
80 pré-molares superiores, sendo usadas as superfícies vestibulares dos dentes para a
colagem dos 80 brackets metálicos. Os dentes foram divididos aleatoriamente em 8
grupos experimentais (n=10), sendo: um grupo controle, redução da metade do tempo
de exposição do grupo controle, um quarto do tempo do grupo controle, função plasma
ou turbo para cada LED estudado, sendo Valo e Bluephase. Após 24 horas da
polimerização, foram realizados os testes de cisalhamento (SBS), índice remanescente
de resina (ARI) e MHV. O objetivo do experimento 3 foi verificar a influência de
diferentes densidades de energia depositadas por dois fotoativadores LED diferentes de
alta potência nas propriedades físicas e mecânicas de uma resina ortodôntica em
brackets cerâmicos. Foram necessários 80 dentes pré-molares superiores hígidos, sendo
utilizadas as superfícies linguais ou palatinas dos dentes para colagem dos 80 brackets
cerâmicos. Os dentes foram divididos aleatoriamente em 8 grupos experimentais
(n=10), foram formados grupos iguais para cada LED Valo e Bluephase: um grupo
controle, diminuição da metade do tempo de exposição do grupo controle, um quarto do
tempo do grupo controle, função turbo do LED Bluephase ou plasma do LED Valo.
Após 24 horas da polimerização, foram realizados os testes de SBS, ARI e MHV. Os
resultados de cada experimento foram analisados através de testes estatísticos
específicos, para determinar se houve ou não diferença estatisticamente significativa.
Para o experimento 1 foram realizados ANOVA de duas vias e teste de Tukey (α=0,05),
para o experimento 2 e 3 foram realizados Anova de duas vias com testes de Tukey
(α=0,05). O experimento 1 mostrou que os grupos dos brackets cerâmicos tem baixa
variação, porém pequenas mudanças no aumento dos valores da energia aplicada em
Joules totais aumentam os valores de DC e MHV, nos brackets metálicos pelo fato de
impedir a passagem da luz o DC e HVK diminuem significativamente, permanecendo
dentro dos parâmetros considerados normais. O experimento 2 mostrou que ambos LED
utilizados foram efetivos tanto na função standard como na turbo ou plasma, sendo que
as funções turbo ou plasma ofereceram resultados similares aos do controle, efetivando
mesmo com a redução do tempo para a polimerização dos brackets metálicos. No
experimento 3 não houve diferença estatisticamente significativa nos grupos analisados.
Os LEDs estudados proporcionaram valores suficientes de Joules em alguns grupos
experimentais sendo este suficiente para atingir bons valores no DC, SBS e MHV. O
uso de LEDs com uma potência adequada, sendo o mínimo de 1200 mW/cm2, ou o uso
de uma potência elevada de entre 2400 a 3200 mW/cm2 e um curto período de tempo de
exposição entre 3 a 6 segundos, são efetivos para a colagem de acessórios ortodônticos. / The objective of this study was to verify the effect of energy density and the time of
exposure of third generation LED light curing agents on a commercially available
orthodontic resin in the values of microhardness, shear, resin remaining index and
degree of conversion. Three experiments were carried out: Experiment 1, the objective
was to evaluate the degree of conversion (DC) and microhardness vickers (MHV) of the
orthodontic resin using two third generation LEDs, as well as different photoactivation
protocols. 80 ceramic brackets and 80 metallic brackets were required and divided into
16 experimental groups (n=10), with the following groups for each LED: control group,
one half, one quarter of the control group time, turbo or plasma function for the
Bluephase and Valo LEDs, respectively. Immediately after the polymerization, the DC
and MHV assays of the specimens were performed. The experiment 2, aimed to verify
the influence of different energy densities emitted by two high power LED
photoactivators on the physical and mechanical properties of an orthodontic resin in
metallic brackets. For this experiment, 80 carious cavity-free, superior human premolar
teeth were used, and the buccal surfaces of the teeth were used for the bonding of the 80
metal brackets. The teeth were randomly divided into 8 experimental groups (n=10),
with the following groups being a control group, half the time of exposure of the control
group, one quarter of the time in the control group, plasma or turbo function for each
LED studied, being Valo and Bluephase. After polymerization, the teeth and specimens
were stored 24h at 37°C to perform the shear tests (SBS), resin remaining index (ARI)
and MHV. The objective of experiment 3 was to verify the influence of different energy
densities deposited by two different LED light-curing on the physical and mechanical
properties of an orthodontic resin in ceramic brackets. For this experiment, it was
necessary to have 80 carious free upper premolar human teeth, using the lingual or
palatine surfaces of the teeth for bonding the 80 ceramic brackets. The teeth were
randomly divided into 8 experimental groups (n=10), equal groups were formed for
each Valo and Bluephase LEDs: one control group, one half-time control group
exposure time, one-fourth time control group, function LED Bluephase turbo or LED
Valo Plasma. After polymerization, the teeth and specimens were stored 24 hours at
37°C to perform the SBS, ARI and MHV tests. The results of each experiment were
analyzed by specific statistical tests to determine whether or not there was a statistically
significant difference. For experiment 1, 2 and two-way ANOVA and Tukey's test
(α=0.05) were performed. Experiment 1 showed that the groups of ceramic brackets
have low variation, but small changes in the increase of the values of the applied energy
in total Joules increase the values of DC and MHV in the metallic brackets because it
prevents the passage of light the DC and HVK decrease significantly, remaining within
the parameters considered normal. Experiment 2 showed that both LEDs were effective
both in the standard function and in the turbo or plasma, and the turbo or plasma
functions gave similar results to the control, even effecting with the reduction of the
time for the polymerization of the metal brackets. In the experiment 3 there was no
statistically significant difference in the analyzed groups. The studied LEDs provided
sufficient values of Joules in some experimental groups being sufficient to reach good
values in DC, SBS and HVK. The use of LEDs with adequate power, being at least
1000 mW/cm2, or the use of a high power of between 2400 and 3200 mW/cm2 and a
short period of exposure of between 3 to 6 seconds, are sufficient for the bonding of
orthodontic accessories.
|
Page generated in 0.0508 seconds