Superheaters suffer large material loss during combustion of waste and biomass, causing a short life time for these expensive components. During combustion, corrosive ash particles are formed and erosion is caused by circulating bed material and sand particles, all contributing to the material loss. This study examines whether corrosion or erosion has the largest effect on this material loss by investigating two superheaters in loop seal during biomass and waste combustion of an 85 MW, Circulating Fluidized Bed (CFB) boiler in Händelö. The samples were investigated by SEM/EDX and XRD with regard to material loss and corrosion products. The superheaters have different thermal conditions since the material temperature in the first superheater that the steam passes is lower than in the one that comes after. In this report, a model to determine the tube temperature in steam boiler superheaters is also described due to the fact that the local tube temperature is of great importance of condensation of corrosive gases such as KCl and NaCl. Material loss was significantly greater on the cooler superheater compared with the warmer. The material temperatures on the outside of the tubes, were calculated to be about 574 °C for the cooler superheater and about 617°C for the warmer superheater. Overall, all analyzes showed low levels of corrosive substances, although there was a certain corrosion tendency, which indicates that material loss of the superheaters is caused by corrosion-assisted erosion. Lower material temperature of the superheater resulted in a higher degree of condensation of corrosive species such as alkali chlorides, which might have accelerated the erosion. The conclusion is that the dominant mechanism of material loss on the superheaters is erosion.

The direct variable costs for heat and electricity production based on solid biomass fuel combustion is approximately 3-5 times lower than the costs in a fossil fuel-oil based boiler in Sweden. In addition waste derived biomass fuels are typically much cheaper than biomass not classified as waste. The introduction of the waste derived fuels; wastewater treatment sludge, demolition wood, and animal waste in a 50MWth circulating fluidized bed (CFB) biomass boiler located in Perstorp, Sweden, led to rapid deposit buildup in superheaters, heavy ash accumulation in economizers and failing boiler tubes and vortex finders that forced frequent boiler shutdowns. This in turn increased the use of expensive oil (fossil fuel) in backup boilers and the CO2 footprint of the on-site energy conversion system. This work aims to increase the general mechanistic understanding of combustion systems using complex fuels, and includes: A mapping of the boiler failure and preventive maintenance statistics; elemental composition analysis of ash, deposits and fuel fractions; flue-gas composition measurements; chemical speciation analysis; an attempt to describe the overall ash transformation reactions and mass balance throughout the combustion process. Scanning electron microscope (SEM) equipped with energy dispersive X-ray spectroscopy (EDS) was used to analyze the elemental composition of ash and deposits. The SEM-EDS results were used together with data from X-ray powder diffraction (XRD) analysis, thermodynamic phase data, and equilibrium calculations in an attempt to quantify the crystalline phases and the overall ash transformation of the process. Based on the findings concerning ash transformation and the failure statistics, it has been possible to identify generic key parameters regarding boiler design and process parameters, enabling major improvements of the CFB boiler availability, a lower overall energy conversion cost and a reduced CO2 footprint. / Den direkta rörliga kostnaden för värme-och elproduktion baserad på fast biobränsle är ungefär 3-5 gånger lägre än kostnaden för fossiloljebaserad produktion. Avfallsklassade fasta biobränslen är vidare oftast betydligt billigare än fasta biobränslen som inte är klassade som avfall. Införandet av de avfallsklassade bränslena; reningsslam, rivningsvirke, och animaliskt avfall i en 50MWth cirkulerande fluidiserad bädd (CFB) -panna, ledde till kraftig beläggningstillväxt i överhettare och ackumulering av aska i ekonomisers, samt haveri av panntuber och centrumrör i cyklonerna, som tvingade fram frekventa pannstopp. Detta ökade i sin tur användningen aveldningsolja (fossilt bränsle) i reservkrafts-pannor vilket resulterade i ett större CO2 utsläpp och en högre kostnad för energiomvandlingen på siten. Detta arbete syftar till att öka den allmänna mekanistiska förståelsen av förbränningssystem som använder komplexa bränslen, och omfattar; haveri- och underhållsstatistik, elementarsammansättningsanalys av aska, beläggningar och bränslefraktioner, rökgasens sammansättning, kemisk specificering av askor och beläggningar, ett försök att beskriva de övergripande askomvandlingsreaktionerna, samt en massbalans för förbränningsprocessen. Svepelektronmikroskop (SEM) utrustat med energidispersiv röntgenspektroskopi (EDS) användes för att analysera den elementära sammansättningen av aska och beläggningar. SEM-EDS-resultaten användes tillsammans med pulverröntgendiffraktionsanalys (XRD), termodynamiska fasdata, och jämviktsberäkningar i ett försök att kvantifiera de kristallina faserna och de övergripande askomvandlingsreaktionerna i processen. Baserat på resultaten rörande askomvandling och haveristatistik, har det varit möjligt att identifiera generiska nyckelparametrar gällande panndesign och processparametrar, som möjliggjort stora förbättringar av CFB pannans tillgänglighet, en lägre totalkostnad för energiomvandlingen på siten samt ett minskat CO2-utsläpp.