Recently, additive manufacturing (AM), or "3D printing," is expanding into civil infrastructure applications, particularly cementitious materials. To ensure the safety, health, and welfare of the public, quality assurance and quality control (QA/QC) methods via standardized testing procedures are of the upmost importance. However, QA/QC methods for these applications have yet to be established. This thesis aims to implement existing ASTM standards to characterize additive manufactured cementitious composites and to gather better information on how to tackle the challenges that are inherent when printing with cementitious materials. In this work, fresh mix properties and hardened concrete properties were investigated using current ASTM standards as a starting point for applying or adapting them for AM applications. Specifically, this project applied existing ASTM standards for fresh mix mortars to measure setting time, flow, and early compressive strength as qualitative indicators of printability, pumpability, and buildability. The fresh mix properties were investigated for 12 different mortar mixes to demonstrate the effect that moisture content, absorption, and sand type can have on these fresh mix properties. The results for setting time and compressive strength demonstrated that there was less variability in the properties when the moisture condition of the aggregate was measured and accounted. Flow was shown to be strongly influenced by the sand type. Additively manufactured mortars were used to print a box in a layer-by-layer process. To evaluate the effect of layering on the flexural strength, three-point bending tests were implemented using four different loading orientations to explore the anisotropic mechanical properties. The observed anisotropic behavior was corroborated with stereo-digital image correlation data showing the stress-strain and load-deflection relationships. Two orientations (A and B) demonstrated brittle behavior while the other two orientations (C and D) experienced quasi-brittle behavior. In addition, setting a minimum unit weight of 132 pcf enabled an analysis of the effect that defects had on the mechanical performance: specimens greater than 132 pcf demonstrated greater and less variable strengths than the specimens less than 132 pcf. The discussion of how defects impacted performance of the different orientations can be valuable when determining how to effectively model, design, and inspect 3D printed structures in the future. The findings of this thesis confirm that existing ASTM standards for mortars can be modified and applied to AM cementitious composites for QA/QC. It is recommended that mixtures used in 3D printing of cementitious composites should design and accommodate the moisture condition of the aggregate to optimize the predictability of the fresh and early-age properties. For the hardened properties, it is recommended that testing procedures such as flexural testing account for anisotropic behavior. Furthermore, for implementation of 3D printed concrete structures, it is highly recommended that design is a function of loading orientation due to the anisotropic properties of the composite. / Master of Science / Recently, additive manufacturing (AM), or "3D printing," is expanding into civil infrastructure applications, specifically cementitious materials such as mortar and concrete. Understanding and predicting the behavior of the materials when using this new technique is vital for quality assurance and quality control (QA/QC). However, standard test methods have yet to be established for this new construction technique. This thesis aims to use existing testing standards to characterize AM cementitious composites and to gather better information on how to tackle the challenges of printing with these materials. In this work, properties before and after the materials hardened were studied by adapting current testing standards. Specifically, this project applied existing testing standards for fresh mix mortars to measure setting time, flow, and early compressive strength. These properties can serve as indicators of specific printing requirements. The fresh mix properties were studied for 12 different mortar mixes to show the effect of moisture content, absorption, and sand type. The results suggest that there was less variability in the properties when the moisture condition and type of the aggregate was accounted. The fresh mix materials were printed in a layer-by-layer process and then hardened in place. The effects of the layers were explored by performing flexure tests using four orientations with respect to how the load was applied to the layers. The observed difference in behavior for the different orientations was supported by digital image correlation data. In addition, an analysis of the effect defects had on the performance was included. Understanding how defects impacted performance can be valuable for effectively designing 3D printed structures in the future. The results of this thesis confirm that existing testing standards for mortars can be adapted and applied to AM cementitious materials for QA/QC. It is recommended that mixtures used in 3D printing of cementitious materials should account for the moisture condition of the aggregate to improve the predictability of the fresh and early-age properties. For the hardened properties, it is recommended that the design is a function of loading orientation due to the difference in behavior for the different orientations of the material.

La nécessité de rénover les réseaux d'assainissement des grandes villes et les besoins de construire de nouvelles structures conduisent les gestionnaires de réseaux d'assainissement et les fabricants de canalisation à rechercher des solutions pour obtenir des installations d'assainissement durables. Parmi les détériorations rencontrées dans ces structures, 9% peuvent être attribués à la biodétérioration des matériaux cimentaires. Cette étude a deux objectifs principaux. Le premier est de développer un essai accéléré reproductible en laboratoire et qui donne des résultats proches de ceux obtenus sur site. Le second est d'étudier la biodétérioration des matériaux cimentaires pour mieux comprendre les mécanismes et plus spécifiquement la différence de comportement entre les matériaux à base de ciment d'aluminate de calcium (CAC) et de ciment Portland ordinaire (OPC). Dans ce cadre, différentes formulations cimentaires ont été exposées in situ afin de déterminer les paramètres influant sur la biodétérioration. En parallèle, des expériences en laboratoire ont été réalisées pour mieux comprendre chaque étape du mécanisme de biodétérioration. Les résultats des expositions sur site montrent que les matériaux à base de CAC ont une durabilité plus importante que les autres formulations cimentaires. Les études réalisées en laboratoire permettent d'attribuer ces meilleures performances à la teneur en aluminium qui inhibe la croissance des microorganismes tout en protégeant la matrice grâce à la précipitation d'une couche d'alumine hydratée dans la porosité et à la surface de ces matériaux et qui maintient le pH à 3,5-4. La chimie de surface a également un rôle important en favorisant ou non l'oxydation abiotique de l'H2S. Les résultats des expositions sur site et des différents essais de laboratoire ont été utilisés pour développer un essai accéléré donnant des résultats prometteurs / The need for renovation of sewer networks in major cities and the necessity to build new structures lead managers of sewer pipe and manufacturers to seek for solutions for sustainable sanitation. 9% of damages encountered in these structures can be attributed to the biodeterioration of cementitious materials. This study has two main objectives. The first one is to develop an accelerated reproducible laboratory test that gives results similar to those obtained on site. The second is to study the biodeterioration of cementitious materials in order to better understand mechanisms and more especially the difference in behavior between materials based on calcium aluminate cement (CAC) and ordinary Portland cement (OPC). Within this framework, different cement formulations were exposed in situ to identify the parameters influencing biodeterioration. Meanwhile, laboratory experiments were conducted to better understand each step of the mechanism of biodeterioration. Results of on site exposition show that materials based on CAC have a greater durability than other cement formulations. Laboratory studies assign these best performances to the aluminum content which inhibits the growth of microorganisms while protecting the matrix by precipitation of a hydrated alumina layer in the porosity and on the surface of these materials. This layer maintains the pH at 3.5-4. Surface chemistry was shown to play an important role in catalizing abiotic oxidation of H2S. The results of on-site exhibitions and various laboratory tests were used to develop an accelerated test giving promising results

A deposição de rejeitos radioativos em repositórios geológicos profundos vem sendo estudada nos últimos anos em diversos países. Materiais à base de cimento são utilizados nesses repositórios como material estrutural, matriz de imobilização de rejeitos ou material de preenchimento. Compreender o desempenho desse material é essencial para garantir a segurança da instalação durante o seu tempo de vida útil (de milhares a centenas de milhares de anos, dependendo do tipo de rejeito). Este trabalho objetiva modelar o comportamento em longo prazo do cimento Portland e estudar a influência de diversos fatores na hidratação e na evolução desse material. A modelagem descritiva abordou a hidratação do cimento nas condições ambientais esperadas no repositório e os efeitos desses fatores em propriedades mecânicas, mineralógicas e morfológicas do cimento. Os fatores ambientais considerados relevantes neste trabalho foram: alta temperatura e pressão, penetração de água subterrânea contendo íons quimicamente agressivos ao cimento e a presença do campo de radiação proveniente dos rejeitos. Ensaios acelerados de degradação também foram realizados para corroborar com o modelo descrito. Observou-se uma sinergia entre diversos fatores na degradação do cimento, como a influência da temperatura e da radiação em reações deletérias ao material. O resultado da modelagem apontou três principais possíveis causas de falha nas barreiras artificiais: a) a formação de um caminho preferencial; b) a perda de resistência e coesão do material; e c) o aumento na corrosão das estruturas metálicas. A descrição do modelo apresentada é a base para a modelagem matemática e a análise de segurança dos repositórios estudados no Brasil. / The radioactive waste disposal in deep geological repositories has been studied for many countries in the last years. Cementitious materials are used in these repositories as structural material, immobilization matrix and as backfill material. The understanding of the performance of these materials is essential to ensure the safety of the installation during its life time (from thousand to hundreds of thousands of years, depending on the type of waste). This works aims at modeling the long-term performance of Portland cement and study the influence of many environmental factors in the hydration and evolution of this material. The modeling approached the cement hydration in the conditions expected in the repository and the effects of these factors on cement mechanical, mineralogical and morphological properties. The environmental factors considered relevant was: high temperature and pressure, the penetration of groundwater containing aggressive chemical ions, and a radiation field from the waste. Degradation accelerated tests were done to corroborate with the descriptive model. It was observed a synergism between some factors on the cement degradation, as the influence of temperature and radiation field in some deleterious reactions in the material. The results of modeling pointed to three main causes of engineered barrier failure: a) the formation of a preferential pathway; b) loss of resistance and cohesion in the material; and c) the increase in the metallic structures corrosion process. The descriptive model is the basis for a mathematical modeling and to perform the safety assessment of the repositories studied in Brazil.

A deposição de rejeitos radioativos em repositórios geológicos profundos vem sendo estudada nos últimos anos em diversos países. Materiais à base de cimento são utilizados nesses repositórios como material estrutural, matriz de imobilização de rejeitos ou material de preenchimento. Compreender o desempenho desse material é essencial para garantir a segurança da instalação durante o seu tempo de vida útil (de milhares a centenas de milhares de anos, dependendo do tipo de rejeito). Este trabalho objetiva modelar o comportamento em longo prazo do cimento Portland e estudar a influência de diversos fatores na hidratação e na evolução desse material. A modelagem descritiva abordou a hidratação do cimento nas condições ambientais esperadas no repositório e os efeitos desses fatores em propriedades mecânicas, mineralógicas e morfológicas do cimento. Os fatores ambientais considerados relevantes neste trabalho foram: alta temperatura e pressão, penetração de água subterrânea contendo íons quimicamente agressivos ao cimento e a presença do campo de radiação proveniente dos rejeitos. Ensaios acelerados de degradação também foram realizados para corroborar com o modelo descrito. Observou-se uma sinergia entre diversos fatores na degradação do cimento, como a influência da temperatura e da radiação em reações deletérias ao material. O resultado da modelagem apontou três principais possíveis causas de falha nas barreiras artificiais: a) a formação de um caminho preferencial; b) a perda de resistência e coesão do material; e c) o aumento na corrosão das estruturas metálicas. A descrição do modelo apresentada é a base para a modelagem matemática e a análise de segurança dos repositórios estudados no Brasil. / The radioactive waste disposal in deep geological repositories has been studied for many countries in the last years. Cementitious materials are used in these repositories as structural material, immobilization matrix and as backfill material. The understanding of the performance of these materials is essential to ensure the safety of the installation during its life time (from thousand to hundreds of thousands of years, depending on the type of waste). This works aims at modeling the long-term performance of Portland cement and study the influence of many environmental factors in the hydration and evolution of this material. The modeling approached the cement hydration in the conditions expected in the repository and the effects of these factors on cement mechanical, mineralogical and morphological properties. The environmental factors considered relevant was: high temperature and pressure, the penetration of groundwater containing aggressive chemical ions, and a radiation field from the waste. Degradation accelerated tests were done to corroborate with the descriptive model. It was observed a synergism between some factors on the cement degradation, as the influence of temperature and radiation field in some deleterious reactions in the material. The results of modeling pointed to three main causes of engineered barrier failure: a) the formation of a preferential pathway; b) loss of resistance and cohesion in the material; and c) the increase in the metallic structures corrosion process. The descriptive model is the basis for a mathematical modeling and to perform the safety assessment of the repositories studied in Brazil.

Water is the most used substance in the world, followed by concrete. Water scarcity is nowadays more common due to concentrated population growth and climate change. Concrete demand is ~15 billion m3 per year fulfilling the need for more and better housing and infrastructure for a growing and wealthier population. Since no other material could fulfil this demand, concrete needs to be produced in a sustainable way, minimizing environmental loads such as water consumption. The water footprint is a tool that measures water use over a products\' life cycle and estimates its potential environmental impacts. Despite the growing concern on water, the existing water footprint methodologies are too complex and require large amounts of data. This study develops a streamlined water footprint methodology for concrete production, simple enough to be useful to the industry and robust enough to be environmentally meaningful. An extensive study on existing water footprint methodologies have been conducted. Then a streamlined methodology was proposed focused on the water flows that are more relevant in concrete production including water quantity and quality letting to meaningful results with less data. Typical water inventory includes the batch water (150-200 H kg/m3), dust control (500-1500 H kg/day), truck washing (13-500 H kg/m3), cement production (0.185-1.333 H kg/kg) and aggregates production (0.116-2.0 H kg/kg). Regarding water quality, the most critical flows - Zinc, Lead, Nitrate, Nitrogen oxides and Sulfur dioxide- were identified based on the contribution of these flows to the potential environmental impacts, the control or influence that the concrete producer has on the activities were these flows appear and the feasibility to measure these flows on site. Concrete water footprint varies due to mix design, technological routes, location and choice of impact assessment method. The results are of interest to the research community as well as to the stakeholders of the cement and concrete industries and a contribution to sustainable construction since study of water footprint is fundamental to improve water efficiency. / A água é a substância mais utilizada no mundo, seguida pelo concreto. A escassez de água é hoje em dia mais comum devido ao crescimento populacional concentrado e às mudanças climáticas. A demanda de concreto é ~15 billion m3 por ano que atende a demanda de mais e melhor moradia e infraestrutura para uma população crescente e mais prospera. Uma vez que nenhum outro material pode satisfazer essa demanda, o concreto precisa ser produzido de forma sustentável, minimizando as cargas ambientais, como o consumo de água. A pegada hídrica é uma ferramenta que mede o uso da água ao longo do ciclo de vida de um produto e estima seus potenciais impactos ambientais. Apesar da crescente preocupação com a água, as metodologias existentes de pegada hídrica são muito complexas e exigem grandes quantidades de dados. Este estudo desenvolve uma metodologia optimizada de pegada hídrica para produção de concreto, simples o suficiente para ser útil para a indústria e robusta o suficiente para ser ambientalmente significativa. Um estudo extensivo em metodologias existentes da pegada da água foi conduzido. Em seguida, uma metodologia optimizada foi proposta focada nos fluxos de água que são mais relevantes na produção de concreto, incluindo quantidade e qualidade, permitindo resultados significativos com menos dados. O inventário de água típica inclui a água de mistura (150-200 H kg/m3), controle de poeira (500-1500 H kg/dia), lavagem de caminhões (13-500 H kg/m3), produção de cimento (0.185-1.333 H kg/kg ) e produção de agregados (0.116-2,0 H kg/kg). Em relação à qualidade da água, os fluxos mais críticos -Zinco, Chumbo, Nitrato, Óxidos de nitrogênio e Dióxido de enxofre-foram identificados com base na contribuição destes fluxos para os potenciais impactos ambientais, o controle ou a influência que o produtor de concreto tem sobre as atividades onde esses fluxos aparecem e a viabilidade para medir esses fluxos no local. A pegada de água de concreto varia devido à formulação, rotas tecnológicas, localização e escolha do método de avaliação de impacto. Os resultados são de interesse para a comunidade de pesquisa, bem como para as partes interessadas das indústrias de cimento e concreto e uma contribuição para a construção sustentável, uma vez que o estudo da pegada hídrica é fundamental para melhorar a eficiência da água.

Civil engineers are at times required to stabilize sulfate bearing clay soils with calcium based stabilizers. Deleterious heaving in these stabilized soils may result over time. This dissertation addresses critical questions regarding the consequences of treating sulfate laden soils with calcium-based stabilizers. The use of a differential scanning calorimeter was introduced in this research as a tool to quantify the amount of ettringite formed in stabilized soils. The first part of this dissertation provides a case history analysis of the expansion history compared to the ettringite growth history of three controlled low strength mixtures containing fly ash with relatively high sulfate contents. Ettringite growth and measurable volume changes were monitored simultaneously for mixtures subjected to different environmental conditions. The observations verified the role of water in causing expansion when ettringite mineral is present. Sorption of water by the ettringite molecule was found to be a part of the reason for expansion. The second part of this dissertation evaluates the existence of threshold sulfate levels in soils as well as the role of soil mineralogy in defining the sensitivity of soils to sulfate-induced damage. A differential scanning calorimeter and thermodynamics based phase diagram approach are used to evaluate the role of soil minerals. The observations substantiated the difference in sensitivity of soils to ettringite formation, and also verified the existence of a threshold level of soluble sulfates in soils that can trigger substantial ettringite growth. The third part of this dissertation identifies alternative, probable mechanisms of swelling when sulfate laden soils are stabilized with lime. The swelling distress observed in stabilized soils is found to be due to one or a combination of three separate mechanisms: (1) volumetric expansion during ettringite formation, (2) water movement triggered by a high osmotic suction caused by sulfate salts, and (3) the ability of the ettringite mineral to absorb water and contribute to the swelling process.

Using recycled concrete aggregate (RCA) as a replacement for natural aggregate in new concrete is a promising way to increase the overall sustainability of new concrete. This has been hindered, however, by a general perception that RCA is a sub-standard material due to the lack of technical guidance, specifically related to long-term durability, on incorporating RCA into new concrete. The goal of this research project was to determine whether current testing methods could be used to assess the potential alkali-silica reactivity of concrete incorporating RCA. The test methods investigated were ASTM C1260 and ASTM C1567 for assessing natural aggregate susceptibility to alkali-silica reactivity (ASR), and the ability of supplementary cementitious materials (SCMs) to mitigate ASR, respectively. Seven different RCA sources were investigated. It was determined that ASTM C1260 was effective in detecting reactivity but expansion varied based on RCA processing. Depending on the aggregate type and the extent of processing, up to a 100% increase in expansion was observed. Replicate testing was performed at four university laboratories to evaluate repeatability and consistency of results. The authors recommend modification to the mixing and aggregate preparation procedures, when testing the reactivity of RCA using ASTM C 1260. This study also investigated the efficacy of replacing portland cement with supplementary cementitious materials (SCMs), known to mitigate alkali-silica reaction (ASR) in concrete with virgin aggregates, to control ASR in concrete incorporating reactive RCA. The SCMs investigated as part of this study included: fly ash (class F), silica fume, and metakaolin. The results of modified alkali-silica reactivity tests, ASTM C1260 and ASTM C1567 (AMBT), are presented for two different recycled concrete aggregates when using 100% portland cement, binary blends of portland cement and fly ash, and ternary blends of portland cement, fly ash and metakaolin or silica fume. The results indicate that SCMs can effectively mitigate ASR in concrete made with RCA. A 40% replacement of portland cement with class F fly ash was able to reduce expansions to below 0.10% in the AMBT for concrete containing 100% of a highly reactive recycled concrete aggregate. A ternary blend, however, of portland cement with a class F fly ash and metakaolin was most effective for both RCAs tested in this study. Higher levels of mitigation may be required for some RCAs, compared to the level required to mitigate ASR in concrete made with their original natural aggregates, depending on the age and composition of the RCA. / Graduation date: 2012

La prédiction du comportement à long terme des matériaux cimentaires est un enjeu majeur pour contribuer à l'étude de la durabilité des structures précontraintes. Le présent travail porte sur l'utilisation de la méthode de l'inclusion équivalente, approche d'homogénéisation multi-échelle simplifiée, pour la prédiction du fluage dans ces matériaux. Le fluage est modélisé par la viscoélasticité linéaire sans vieillissement. La méthode de l'inclusion équivalente permet de contourner certaines difficultés et limitations que présentent les approches classiques. Pour les matériaux cimentaires, fortement hétérogènes, les approches multiéchelles classiques sont ou bien numériquement lourdes et très complexes à mettre en œuvre, ou bien pas suffisamment détaillées pour prendre en compte les spécificités d'une microstructure. La méthode de l'inclusion équivalente présente un juste-milieu et permet de calculer des microstructures simplifiées de type matrice-inclusions et de fournir des estimations ou des bornes sur le comportement homogénéisé. Sous sa forme variationnelle, la méthode de l'inclusion équivalente n'a jusqu'alors été mise en œuvre que pour des inclusions de forme sphérique. Le présent travail propose d'étendre cette méthode à des inclusions de forme ellipsoïdale dont la variation de l'élancement permet de modéliser de nouveaux éléments asphériques tels que les fissures, les fibres et les cristaux de portlandite. Cette complexification de la géométrie a un impact sur le temps de calcul, qui est amplifié dans le cadre du fluage. Le second volet du travail porte alors sur l'extension de la méthode de l'inclusion équivalente à la viscoélasticité linéaire sans vieillissement par l'intermédiaire de la transformée de Laplace-Carson. Une méthodologie efficace (tant du point de vue de la précision que de celui du temps de calcul) est finalement proposée pour effectuer l'inversion numérique de cette transformée / The prediction of long-term behaviour of cementitious materials is a major concern which contributs to the study of the durability of prestressed structures. This work focuses on the use of the equivalent inclusion method, simplified multi-scale homogenization approach, for the prediction of creep in these materials. Creep is modelled by the non-ageing linear viscoelasticity. The equivalent inclusion method overcomes certain difficulties and limitations posed by conventional approaches. For cementitious materials (highly heterogeneous), conventional multi-scale approaches are, either digitally heavy and complex to implement, or not sufficiently detailed to take into account the specificities of a microstructure. The equivalent inclusion method presents a middle way and allows the calculation of simplified matrix-inclusion type microstructures and to provide estimates or bounds on the homogenized behaviour.Under its variational form, the equivalent inclusion method has, up to now, been implemented only for spherical inclusions. This work proposes to extend this method to ellipsoidal inclusions whose variation of slenderness allows the modelling of new aspheric elements such as cracks, fibers and portlandite crystals. Such enrichment of the geometry has an impact on the computation time, that is amplified in the context of creep. The second aspect of the work then applies to the extension of the equivalent inclusion method to the non-ageing linear viscoelasticity by means of the Laplace-Carson transform. An effective methodology (both from the viewpoint of precision and calculation time) is finally proposed to perform the numerical inversion of this transform

La prédiction du comportement à long terme des matériaux cimentaires est un enjeu majeur pour contribuer à l'étude de la durabilité des structures précontraintes. Le présent travail porte sur l'utilisation de la méthode de l'inclusion équivalente, approche d'homogénéisation multi-échelle simplifiée, pour la prédiction du fluage dans ces matériaux. Le fluage est modélisé par la viscoélasticité linéaire sans vieillissement. La méthode de l'inclusion équivalente permet de contourner certaines difficultés et limitations que présentent les approches classiques. Pour les matériaux cimentaires, fortement hétérogènes, les approches multiéchelles classiques sont ou bien numériquement lourdes et très complexes à mettre en œuvre, ou bien pas suffisamment détaillées pour prendre en compte les spécificités d'une microstructure. La méthode de l'inclusion équivalente présente un juste-milieu et permet de calculer des microstructures simplifiées de type matrice-inclusions et de fournir des estimations ou des bornes sur le comportement homogénéisé. Sous sa forme variationnelle, la méthode de l'inclusion équivalente n'a jusqu'alors été mise en œuvre que pour des inclusions de forme sphérique. Le présent travail propose d'étendre cette méthode à des inclusions de forme ellipsoïdale dont la variation de l'élancement permet de modéliser de nouveaux éléments asphériques tels que les fissures, les fibres et les cristaux de portlandite. Cette complexification de la géométrie a un impact sur le temps de calcul, qui est amplifié dans le cadre du fluage. Le second volet du travail porte alors sur l'extension de la méthode de l'inclusion équivalente à la viscoélasticité linéaire sans vieillissement par l'intermédiaire de la transformée de Laplace-Carson. Une méthodologie efficace (tant du point de vue de la précision que de celui du temps de calcul) est finalement proposée pour effectuer l'inversion numérique de cette transformée / The prediction of long-term behaviour of cementitious materials is a major concern which contributs to the study of the durability of prestressed structures. This work focuses on the use of the equivalent inclusion method, simplified multi-scale homogenization approach, for the prediction of creep in these materials. Creep is modelled by the non-ageing linear viscoelasticity. The equivalent inclusion method overcomes certain difficulties and limitations posed by conventional approaches. For cementitious materials (highly heterogeneous), conventional multi-scale approaches are, either digitally heavy and complex to implement, or not sufficiently detailed to take into account the specificities of a microstructure. The equivalent inclusion method presents a middle way and allows the calculation of simplified matrix-inclusion type microstructures and to provide estimates or bounds on the homogenized behaviour.Under its variational form, the equivalent inclusion method has, up to now, been implemented only for spherical inclusions. This work proposes to extend this method to ellipsoidal inclusions whose variation of slenderness allows the modelling of new aspheric elements such as cracks, fibers and portlandite crystals. Such enrichment of the geometry has an impact on the computation time, that is amplified in the context of creep. The second aspect of the work then applies to the extension of the equivalent inclusion method to the non-ageing linear viscoelasticity by means of the Laplace-Carson transform. An effective methodology (both from the viewpoint of precision and calculation time) is finally proposed to perform the numerical inversion of this transform

La durabilité des structures en béton armé ainsi que leur durée de vie sont étroitement liées à la mise en œuvre simultanée de nombreux phénomènes physiques et chimiques. Ceux-ci sont de diverses natures mais restent, en général, fonction des propriétés hydriques des matériaux étudiés. Ainsi, la prédiction des dégradations potentielles d'un matériau cimentaire requiert l'étude du transport de l'eau liquide et des phases gazeuses à travers ce dernier, considéré comme un milieu poreux. En milieu naturel, les structures subissent des variations périodiques de l'humidité relative extérieure (HR). Cependant, la plupart des modèles de transfert hydrique préexistants dans la littérature, s'intéresse uniquement au processus de séchage. Il existe peu de modèles décrivant à la fois l'humidification et le séchage du matériau (ces deux phénomènes se produisent dans le matériau en condition naturelle d'humidité relative (HR)). Tenir compte des phénomènes d'hystérésis dans les transferts hydriques réduit à nouveau le nombre de modèles à disposition. Ainsi, cette thèse s'attache à proposer une meilleure compréhension de l'état hydrique du béton en fonction des variations d'humidité relative extérieure, sur la base d'une nouvelle campagne expérimentale et de modélisations numériques. Un soin sera apporté afin de tenir compte dans les modèles numériques des effets d'hystérésis. Dans ce travail, nous détaillerons, tout d'abord, un modèle multi-phasiques complet. Un modèle simplifié est obtenu, sur la base de considérations théoriques et de vérifications expérimentales dans le cas où la perméabilité intrinsèque à l'eau liquide reste très inférieure à la perméabilité intrinsèque au gaz. Une étude comparative des modèles d'hystérésis couramment utilisés permet d'obtenir un jeu de modèles proposant les meilleures prédictions d'isothermes de sorption d'eau et de leurs hystérésis. Par la suite, le modèle de transport simplifié est couplé avec les modèles d'hystérésis sélectionnés afin de simuler les transferts hydriques dans des bétons soumis à des cycles d'humidification-séchage. La comparaison avec des données expérimentales révèle que la prise en compte de l'hystérésis de l'isotherme de sorption d'eau ne peut pas être négligé. De plus, il est montré que les prédictions obtenues avec des modèles d'hystérésis théoriques, sont les plus cohérentes avec les résultats expérimentaux, en particulier, pour des chemins secondaires d'hystérésis. Plusieurs scénarios (conditions environnementales, bétons différents) sont également simulés. Les résultats obtenus pointent à nouveau la nécessité de tenir compte de l'hystérésis lors de la modélisation des transferts hydriques à travers des matériaux cimentaires soumis à des variations d'humidité relative. La définition d'une profondeur pour laquelle le profil hydrique du béton est modifié par les variations périodiques d'humidité relative permet de mieux comprendre comment la modélisation de la pénétration des espèces ioniques est influencée par les cycles d'humidification-séchage. Par ailleurs, notre analyse révèle qu'il est pertinent de considérer l'effet de Knudsen pour la diffusion de la vapeur afin d'améliorer la prédiction de la diffusivité apparente / The durability of reinforced concrete structures and their service life are closely related to the simultaneous occurrence of many physical and chemical phenomena. These phenomena are diverse in nature, but in common they are dependent on the moisture properties of the material. Therefore, the prediction of the potential degradation of cementitious materials requires the study of the movement of liquid-water and gas-phase transport in the material which is considered as a porous medium. In natural environment, structures are always affected by periodic variations of external relative humidity (RH). However, most moisture transport models in the literature only focus on the drying process. There are few researches considering both drying and wetting, although these conditions represent natural RH variations. Even few studies take into account hysteresis in moisture transport. Thus, this work is devoted to better understand how the moisture behaviour within cementitious materials responds to the ambient RH changes through both experimental investigations and numerical modelling. In particular, hysteretic effects will be included in numerical modelling. In this thesis, we first recalled a complicate multi-phase continuum model. By theoretical analysis and experimental verification, a simplified model can be obtained for the case of that the intrinsic permeability to liquid-water is smaller than the intrinsic permeability to gas-phase. The review of commonly-used hysteresis models enabled to conclude a set of best models for the prediction of water vapour sorption isotherms and their hysteresis. After that, the simplified model was coupled with selected hysteresis models to simulate moisture transport under drying and wetting cycles. Compared with experimental data, numerical simulations revealed that modelling with hysteretic effects can provide much better results than non-hysteresis modelling. Among different hysteresis models, results showed that the use of the conceptual hysteresis model, which presents closed form scanning loops, can provide more accuracy predictions. Further simulations for different scenarios were also performed. All comparisons and investigations enhanced the necessity of considering hysteresis to model moisture transport for varying relative humidity at the boundary. The investigation of moisture penetration depth could provide a better understanding of how deep moisture as well as ions can move into the material. Furthermore, the analysis revealed that the consideration of Knudsen effects for diffusion of vapour can improve the prediction of the apparent diffusivity