Spelling suggestions: "subject:"combustion research"" "subject:"ombustion research""
21 |
Smoldering combustion of flexible polyurethane foamOrtiz Molina, Marcos German. January 1980 (has links)
Thesis: Ph. D., Massachusetts Institute of Technology, Department of Mechanical Engineering, 1980 / Includes bibliographical references. / by Marcos German Ortiz Molina. / Ph. D. / Ph. D. Massachusetts Institute of Technology, Department of Mechanical Engineering
|
22 |
Experimental measurement of combustion noise and comparison to a predictive modelWesterman, William J. 12 March 2009 (has links)
The acoustic emission from the combustion of turbulent mixtures of several gaseous fuels and oxygen was measured to determine the effect of burner diameters, flow velocities and reactant chemistries. The data are presented in the form of acoustic pressure spectra and over-all sound pressure levels.
The experiment consisted of a geometrically simple pre-mixed burner with five interchangeable nozzles whose diameters varied from 0.117 cm to 0.541 cm. The fuels examined in the experiment were acetylene, methane and propane. Three flow velocities were tested for each fuel. Methane was tested within a velocity range of 10 m/s to 25 m/s while propane was examined within a range of 20 m/s to 40 m/s. Acetylene was tested at somewhat higher velocities ranging from 50 m/s to 100 m/s.
The resulting data base consisted of 23 unique test conditions. The data were evaluated based on peak frequency and overall sound pressure level. The experimental data are also compared to a predictive model. / Master of Science
|
23 |
Development of air/fuel ratio control and secondary combustion for a commercial-scale biomass-fueled boilerHarris, Charles G. January 1988 (has links)
The development, testing, and modeling of a multi-fuel biomass combustion system is described. The system is developed by adding air/fuel ratio control and catalytic secondary combustion to a commercially available 150 kW biomass-fueled boiler. The basis of the air/fuel ratio control system is an inexpensive electrochemical oxygen sensor. A catalytic secondary combustion system is developed from monolithic noble metal catalytic combustor segments commonly used on domestic wood burning equipment. The development and understanding of the combustion system is supported by both experimental measurements and theoretical modeling of the combustion process. Experimentally measured variables include gas temperatures, combustion air and exhaust gas flow rates, exhaust gas CO and CO₂ concentrations, and useful heat output. Both equilibrium and chemical kinetic models of the gas-phase combustion process are developed. In the kinetic model, mixing is modeled by assuming the combustion passages behave as a series of perfectly mixed reactors.
The modified boiler reduces CO output to about 10 to 15 percent of the CO produced by the baseline unit in steady operation. Results of the combustion modeling indicate that the combustion proceeds nearly to equilibrium except when operating with fuel/air equivalence ratios less than about 0.7 and immediately after addition of a batch of fuel. Under these conditions the gas temperatures are usually low enough to impose a kinetic limit on the combustion process. Equilibrium calculations reveal that more than one-half of the total heat transfer from the combustion products occurs in the combustion zone, indicating that there may be opportunity to reduce kinetic limitations by restricting heat losses from the combustion zone. / Master of Science
|
24 |
Long-term thermal/chemical degradation of ceramic candle filter materialsMiller, Jean P. 17 March 2010 (has links)
Commercial ceramic candle filters were exposed to harsh environments to determine the effects of alkali and steam on their long-term durability. Ceramic candle filters are composed of relatively coarse aggregates fixed by a ceramic bond. The filters studied include a clay-bonded, granular aluminosilicate candle and three types of clay-bonded, granular SiC candles. The alkali, steam, and steam-alkali corrosion of these commercial ceramic candle filters was examined at temperatures ranging from 450 to 1225°C and pressures up to 1000 psi. Results indicate that the aluminosilicate candle filters perform better than filters made from granular SiC. The SiC filters show binder degradation in steam as well as in alkali-containing environments at temperatures as low as 700°C, with oxidation of the SiC occurring in the steam environments at higher temperatures. Sodium and potassium contaminants in the steam atmospheres accelerate the degradation of both types of filter material. / Master of Science
|
25 |
Low NOx coal burner temperature profile evaluationSmit, Dewan January 2016 (has links)
A dissertation submitted to the Faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, in fulfilment of the requirements for the degree of Master of Science in Engineering.
Johannesburg 2016 / Stringent worldwide emissions legislation, the drive to lower carbon emissions, together with the ever increasing demand to preserve the environment has led to a considerable demand for cleaner and more efficient coal combustion technologies. A primary technology for the reduction of emissions of oxides of nitrogen (NOx) is the installation of low NOx coal combustion burners. Extensive research into various burner characteristics and, in particular, the aerodynamic characteristics required to improve combustion performance of low NOx coal burners has been extensively undertaken and is ongoing.
In this work the aerodynamic behaviour of a full-scale, aerodynamically staged, single low-NOx coal burner was numerically investigated. The objective of the study was to develop a single low NOx burner CFD model in Ansys Fluent, to better characterize and understand the flame shape in terms of the temperature profile achieved. CFD serve as an additional tool to assist with plant optimization, design proposals and occurrence investigations. To have confidence in the single burner coal combustion CFD model, the results of the model were compared to data obtained from an existing operational low NOx burner on site during a pre-defined load condition. To further improve on the theoretical CFD combustion model, drop tube furnace (DTF) experiments have been done to calculate the single rate Arrhenius kinetic parameters (pre-exponential factor and activation energy) for coal devolatilization and char combustion of the specific South African coal used.
The combustion CFD simulations showed with a lower than design air flow through the burner, a reduced amount of swirl was achieved. This reduced amount of swirl produces a jet like flame and influences the way in which the combustion species are brought together. Under these operating conditions the flame distance from the burner mouth was predicted to be 1.2 (m). A very promising result was obtained through CFD and compared well with the in-flame temperature measurement obtained through the burner centre-line of approximately 1.4 (m). In an attempt to improve the aerodynamic profile of the burner under the same operating conditions the swirl angle on the tertiary air (TA) inlet was increased. The increased swirl on the TA inlet of the burner showed an improvement on the aerodynamic profile and had a significant impact on the temperature distribution within the flame. The increased swirl resulted in an improved flame distance of approximately 0.5 (m) from the burner mouth. The effect of increased swirl on the temperature profile of the flame displayed the aerodynamic dependence of the low NOx burner on combustion performance. / MT2017
|
26 |
Self-sustained combustion of low grade solid fuels in a stagnation-point reverse-flow combustorRadhakrishnan, Arun 13 January 2014 (has links)
This thesis investigates the use of the Stagnation-Point Reverse-Flow (SPRF) combustor geometry for burning low-grade solid fuels that are attractive for specific industrial applications because of their low cost and on-site availability. These fuels are in general, hard to burn, either because of high moisture and impurity-content, e.g. biomass, or their low-volatiles content, e.g., petroleum-coke. This results in various challenges to the combustor designer, for example reduced flame stability and poor combustion efficiency. Conventional solutions include preheating the incoming flow as well as co-firing with high-grade fuels. The SPRF combustor geometry has been chosen because it was demonstrated to operate stably on standard gaseous and liquid-fuels corresponding to ultra fuel-lean conditions and power densities at atmospheric-pressure around 20-25 MW/m3. Previous studies on the SPRF combustor have proven that the unique, reverse flow-geometry allows entrainment of near-adiabatic products into the incoming reactants, thereby enhancing the reactivity of the mixture. Further, the presence of the stagnation-end created a region of low mean velocities and high levels of unsteadiness and mixing-rates that supported the reaction-zones. In this study, we examine the performance of the SPRF geometry on a specific low grade solid fuel, petroleum coke.
There are three main goals of this thesis. The first goal is the design of a SPRF combustor to operate on solid-fuels based on a design-scaling methodology, as well as demonstration of successful operation corresponding to a baseline condition. The second goal involves understanding the mode of operation of the SPRF combustor on solid-fuels based on visualization studies. The third goal of this thesis is developing and using reduced-order models to better understand and predict the ignition and quasi-steady burning behavior of dispersed-phase particles in the SPRF combustor.
The SPRF combustor has been demonstrated to operate stably on pure-oxygen and a slurry made from water and petroleum-coke, both at the baseline conditions (125 kW, 18 g/s, ~25 µm particles) and higher power-densities and powder sizes. For an overall combustor length less than a meter, combustion is not complete (global combustion efficiency less than 70%). Luminance imaging results indicate the incoming reactant jet ignites and exhibits intense burning at the mid-combustor region, around 15 jet diameters downstream of the inlet, most likely due to enhanced mixing as a result of the highly unsteady velocity field. This roughly corresponds to the location of the reaction zones in the previous SPRF combustors operating on gas and liquid fuels. Planar laser visualization of the reacting flow-field using particle-scattering reveals that ignition of a significant amount of the reactants occurs only after the incoming jet has broken into reactant packets. Post-ignition, these burning packets burn out slowly as they reverse direction and exit the combustor on either side of the central injector. This is unlike the behavior in liquid and gas-fueled operation where the incoming reactants burned across a highly corrugated, thin-flame front. Based on these findings, as well as the results of previous SPRF studies, an idealized model of combustor operation based on a plug flow reactor has been developed. The predictions suggest that fuel-conversion efficiency is enhanced by the combustor operating pressure and lowered by the heat-losses.
Overall, this effort has shown the SPRF geometry is a promising compact-combustor concept for self-sustained operation on low-grade solid-fuels for typical high-pressure applications such as direct steam-generation. Based on these findings, it is recommended that future designs for the specific application previously mentioned have a shorter base-combustor with lower heat-losses and a longer steam-generation section for injection of water.
|
27 |
Laser diagnostics in MILD combustion.Medwell, Paul R. January 2007 (has links)
Despite mounting concerns of looming global warming and fuel shortages, combustion will remain the predominant source of fulfilling the world’s ever-increasing demand for energy in the foreseeable future. In light of these issues, the combustion regime known as Moderate and Intense Low oxygen Dilution (MILD) combustion has the potential of offering increased efficiency whilst lowering pollutant emissions. Essentially, MILD combustion relies on the reuse of the exhaust gases from the combustion process to simultaneously dilute the oxygen concentration of the oxidant stream, and increase its temperature. The benefit of this technique is that it results in a vast reduction in emissions, especially oxides of nitrogen. In addition, the thermal efficiency of the combustion process is increased, reducing fuel demands, as well as producing a more uniform heating profile and subsequently better product quality for many applications. The recirculation of exhaust gas and heat has been utilised for applications in the past. MILD combustion aims to extend the advantages of heat recovery and exhaust gas recirculation beyond the boundaries that are otherwise possible using conventional techniques. The relatively new concept of MILD combustion is a major advancement to the previous technology, and many fundamental issues have not yet been resolved. In a furnace environment, the dilution and preheating of the reactants generate a unique “distributed” reaction zone. There is a need to better understand the structure of this combustion regime and the parameters which control it. To emulate MILD combustion conditions in a controlled experimental environment, a Jet in Hot Coflow (JHC) burner is used in this study. The MILD combustion regime is examined using laser diagnostic techniques. The two key flame intermediates hydroxyl radical (OH) and formaldehyde (H2CO), as well as temperature, are imaged simultaneously to reveal details relating to the reaction zone. Simultaneous imaging enables not only the spatial distribution of each scalar to be investigated, but also the combined effect of the interactions of the three measured scalars. The role of four key variables are investigated as part of this work, namely; the coflow oxygen (O2) level, the jet Reynolds number, fuel dilution and fuel type. Also considered is the effect of surrounding air entrainment into the hot and diluted coflow, which causes a deviation from MILD combustion conditions. The local oxygen (O2) concentration is a key parameter in the establishment of MILD combustion conditions. The effect of lowering the O2 level is to lead to reductions in the OH and temperature in the reaction zone, in effect leading to a less intense reaction. When comparatively high oxygen laden, cold surrounding air mixes with the hot and low O2 coflow, MILD combustion conditions no longer exist. In this case, the flame front can become locally extinguished and subsequent premixing with the high O2 concentrations can lead to increased reaction rates and hence higher temperatures. It is therefore essential that fresh air must be excluded from a MILD combustor to maintain the stable reaction which typifies MILD combustion. It is found that the flame structure is relatively insensitive to both the type of hydrocarbon fuel and the Reynolds number. Each of these parameters can lead to changes in some intermediate species, namely formaldehyde, yet the OH and temperature measurements show comparatively minor variation. Nevertheless, fuel type and Reynolds number, in the form of increased flow convolution, can lead to striking differences in the flame structure. One of the most prominent effects is noted with the dilution of the fuel with various diluents. Some of the flames visually appear lifted, whereas the measurements reveal the occurrence of pre-ignition reactions in the “lifted” region. The unique characteristics of the stabilisation for these particular cases has lead to the term transitional flames. The fundamental aspects discovered by this study shed new light on the reaction zone structure under MILD combustion conditions. By advancing understanding of MILD combustion, future combustion systems will be able to better utilise the efficiency increases and lower pollutant benefits it offers. / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1293788 / Thesis (Ph.D.) -- University of Adelaide, School of Mechanical Engineering, 2007.
|
28 |
Laser diagnostics in MILD combustion.Medwell, Paul R. January 2007 (has links)
Despite mounting concerns of looming global warming and fuel shortages, combustion will remain the predominant source of fulfilling the world’s ever-increasing demand for energy in the foreseeable future. In light of these issues, the combustion regime known as Moderate and Intense Low oxygen Dilution (MILD) combustion has the potential of offering increased efficiency whilst lowering pollutant emissions. Essentially, MILD combustion relies on the reuse of the exhaust gases from the combustion process to simultaneously dilute the oxygen concentration of the oxidant stream, and increase its temperature. The benefit of this technique is that it results in a vast reduction in emissions, especially oxides of nitrogen. In addition, the thermal efficiency of the combustion process is increased, reducing fuel demands, as well as producing a more uniform heating profile and subsequently better product quality for many applications. The recirculation of exhaust gas and heat has been utilised for applications in the past. MILD combustion aims to extend the advantages of heat recovery and exhaust gas recirculation beyond the boundaries that are otherwise possible using conventional techniques. The relatively new concept of MILD combustion is a major advancement to the previous technology, and many fundamental issues have not yet been resolved. In a furnace environment, the dilution and preheating of the reactants generate a unique “distributed” reaction zone. There is a need to better understand the structure of this combustion regime and the parameters which control it. To emulate MILD combustion conditions in a controlled experimental environment, a Jet in Hot Coflow (JHC) burner is used in this study. The MILD combustion regime is examined using laser diagnostic techniques. The two key flame intermediates hydroxyl radical (OH) and formaldehyde (H2CO), as well as temperature, are imaged simultaneously to reveal details relating to the reaction zone. Simultaneous imaging enables not only the spatial distribution of each scalar to be investigated, but also the combined effect of the interactions of the three measured scalars. The role of four key variables are investigated as part of this work, namely; the coflow oxygen (O2) level, the jet Reynolds number, fuel dilution and fuel type. Also considered is the effect of surrounding air entrainment into the hot and diluted coflow, which causes a deviation from MILD combustion conditions. The local oxygen (O2) concentration is a key parameter in the establishment of MILD combustion conditions. The effect of lowering the O2 level is to lead to reductions in the OH and temperature in the reaction zone, in effect leading to a less intense reaction. When comparatively high oxygen laden, cold surrounding air mixes with the hot and low O2 coflow, MILD combustion conditions no longer exist. In this case, the flame front can become locally extinguished and subsequent premixing with the high O2 concentrations can lead to increased reaction rates and hence higher temperatures. It is therefore essential that fresh air must be excluded from a MILD combustor to maintain the stable reaction which typifies MILD combustion. It is found that the flame structure is relatively insensitive to both the type of hydrocarbon fuel and the Reynolds number. Each of these parameters can lead to changes in some intermediate species, namely formaldehyde, yet the OH and temperature measurements show comparatively minor variation. Nevertheless, fuel type and Reynolds number, in the form of increased flow convolution, can lead to striking differences in the flame structure. One of the most prominent effects is noted with the dilution of the fuel with various diluents. Some of the flames visually appear lifted, whereas the measurements reveal the occurrence of pre-ignition reactions in the “lifted” region. The unique characteristics of the stabilisation for these particular cases has lead to the term transitional flames. The fundamental aspects discovered by this study shed new light on the reaction zone structure under MILD combustion conditions. By advancing understanding of MILD combustion, future combustion systems will be able to better utilise the efficiency increases and lower pollutant benefits it offers. / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1293788 / Thesis (Ph.D.) -- University of Adelaide, School of Mechanical Engineering, 2007.
|
29 |
Premixed flame kinematics in a harmonically oscillating velocity fieldShin, Dong-hyuk 13 November 2012 (has links)
Air pollution regulations have driven modern power generation systems to move from diffusion to premixed combustion. However, these premixed combustion systems are prone to combustion instability, causing high fluctuations in pressure and temperature. This results in shortening of component life, system failure, or even catastrophic disasters. A large number of studies have been performed to understand and quantify the onset of combustion instability and the limit cycle amplitude. However, much work remains due to the complexity of the process associated with flow dynamics and chemistry. This thesis focuses on identifying, quantifying and predicting mechanisms of flame response subject to disturbances.
A promising tool for predicting combustion instability is a flame transfer function. The flame transfer function is obtained by integrating unsteady heat release over the combustor domain. Thus, the better understanding of spatio-temporal characteristics of flame is required to better predict the flame transfer function. The spatio-temporal flame response is analyzed by the flame kinematic equation, so called G-equation. The flame is assumed to be a thin interface separating products and reactant, and the interface is governed by the local flow and the flame propagation.
Much of the efforts were done to the flame response subject to the harmonic velocity disturbance. A key assumption allowing for analytic solutions is that the velocity is prescribed. For the mathematical tools, small perturbation theory, Hopf-Lax formula and numerical simulation were used. Solutions indicated that the flame response can be divided into three regions, referred to here as the near-field, mid-field, and farfield. In each regime, analytical expressions were derived, and those results were compared with numerical and experimental data.
In the near field, it was shown that the flame response grows linearly with the normal component of the velocity disturbance. In the mid field, the flame response shows peaks in gain, and the axial location of these peaks can be predicted by the interference pattern by two characteristic waves. Lastly, in the far field where the flame response decreases, three mechanisms are studied; they are kinematic restoration, flame stretch, and turbulent flow effects. For each mechanism, key parameters are identified and their relative significances are compared.
|
30 |
Dynamics of longitudinally forced bluff body flames with varying dilatation ratiosPlaks, Dmitriy Vital 09 November 2009 (has links)
This thesis focuses on experimentally measuring the response of varying dilatation ratio bluff body flames under harmonic excitation. Such flames are often encountered in jet engine afterburners and are susceptible to combustion instabilities. Previous work has been done modeling such flames, however, only limited experimental data has been obtained at these conditions and is the motivation for this thesis.
The focus of this work is to measure the transfer function of longitudinally forced, varying dilatation ratio bluff body flames. The transfer function is obtained by measuring flame position and flame luminosity fluctuations at the forcing frequency. Specifically, the amplitude and phase of the fluctuations are characterized as a function of flow velocity, axial location, and perturbation amplitude. These measurements are also compared to available theoretical predictions, showing that qualitative measured trends are consistent with theory. In addition, a detailed quantitative comparison is performed at one condition, showing good agreement between predictions and measurements in the near and mid-field of the flame response. However, agreement is not obtained in the far-field, indicating that continued theoretical work is needed to understand the flame response characteristics in this region.
|
Page generated in 0.1086 seconds