An experimental and analytical study was conducted on a BT-63 prestressed concrete girder to investigate the thermal effects on the girder. A 2D finite element heat transfer analysis model was then developed which accounted for heat conduction, convection, radiation, and irradiation. The solar radiation was predicted using the location and geometry of the girder, variations in the solar position, and the shadow from the top flange on other girder surfaces. The girder temperatures obtained from the 2D heat transfer analysis matched well with the measurements. Using the temperatures from the 2D heat transfer analysis, a 3D solid finite element analysis was performed assuming the temperatures constant along the length of the girder. The maximum vertical displacement due to measured environmental conditions was found to be 0.29 inches and the maximum lateral displacement was found to be 0.57 inches. Using the proposed numerical approach, extremes in thermal effects including seasonal variations and bridge orientations were investigated around the United States to propose vertical and transverse thermal gradients which could then be used in the design of I-shaped prestressed concrete bridge girders. A simple beam model was developed to calculate the vertical and lateral thermal deformations which were shown to be within 6% of the 3D finite element analyses results. Finally, equations were developed to predict the maximum thermal vertical and lateral displacements for four AASHTO-PCI standard girders. To analyze the combined effects of thermal response, initial sweep, and bearing support slope on a 100-foot long BT-63 prestressed concrete girder, a 3D finite element sequential analysis procedure was developed which accounted for the changes in the geometry and stress state of the girder in each construction stage. The final construction stage then exposed the girder to thermal effects and performed a geometric nonlinear analysis which also considered the nonlinear behavior of the elastomeric bearing pads. This solution detected an instability under the following conditions: support slope of 5¡Æ and initial sweep of 4.5 inches.

Ultra-High Performance Concrete (UHPC) is a new class of concrete characterized by no coarse aggregate, steel fiber reinforcement, low w/c, low permeability, compressive strength exceeding 29,000 psi (200 MPa), tensile strength ranging from 1,200 to 2,500 psi (8 to 17 MPa), and very high toughness. These properties make prestressed precast UHPC bridge girders a very attractive replacement material for steel bridge girders, particularly when site demands require a comparable beam depth to steel and a 100+ year life span is desired. In order to efficiently utilize UHPC in bridge construction, it is necessary to create new design recommendations for its use. The interface between precast UHPC girder and cast-in-place concrete decks must be characterized in order to safely use composite design methods with this new material. Due to the lack of reinforcing bars, all shear forces in UHPC girders have to be carried by the concrete and steel fibers. Current U.S. codes do not consider fiber reinforcement in calculating shear capacity. Fiber contribution must be accurately accounted for in shear equations in order to use UHPC. Casting of UHPC may cause fibers to orient in the direction of casting. If fibers are preferentially oriented, physical properties of the concrete may also become anisotropic, which must be considered in design. The current research provides new understanding of shear and shear friction phenomena in UHPC including: *Current AASHTO codes provide a non-conservative estimate of interface shear performance of smooth UHPC interfaces with and without interface steel. *Fluted interfaces can be created by impressing formliners into the surface of plastic UHPC. AASHTO and ACI codes for roughened interfaces are conservative for design of fluted UHPC interfaces. *A new equation for the calculation of shear capacity of UHPC girders is presented which takes into account the contribution of steel fiber reinforcement. *Fibers are shown to preferentially align in the direction of casting, which significantly affects compressive behavior of the UHPC.

Condition assessment and safety verification of existing bridges and decisions as to whether bridge posting is required are addressed through analysis, load testing, or a combination of methods. Bridge rating through structural analysis is by far the most common procedure for rating existing bridges. The American Association of State Highway and Transportation Officials (AASHTO) Manual for Bridge Evaluation (MBE), First Edition permits bridge capacity ratings to be determined through allowable stress rating (ASR), load factor rating (LFR) or load and resistance factor rating (LRFR); the latter method is keyed to the AASHTO LRFD Bridge Design Specifications, which is reliability-based and has been required for the design of new bridges built with federal findings since October, 2007. A survey of current bridge rating practices in the United States has revealed that these three methods may lead to different ratings and posting limits for the same bridge, a situation that carries serious implications with regard to the safety of the public and the economic well-being of communities that may be affected by bridge postings or closures. To address this issue, a research program has been conducted with the overall objective of providing recommendations for improving the process by which the condition of existing bridge structures is assessed. This research required a coordinated program of load testing and finite element analysis of selected bridges in the State of Georgia to gain perspectives on the behavior of older bridges under various load conditions. Structural system reliability assessments of these bridges were conducted and bridge fragilities were developed for purposes of comparison with component reliability benchmarks for new bridges. A reliability-based bridge rating framework was developed, along with a series of recommended improvements to the current bridge rating methods, which facilitate the incorporation of various in situ conditions of existing bridges into the bridge rating process at both component and system levels. This framework permits bridge ratings to be conducted at three levels of increasing complexity to achieve the performance objectives, expressed in the terms of reliability, that are embedded in the LRFR option of the AASHTO Manual of Bridge Evaluation. This research was sponsored by the Georgia Department of Transportation, and has led to a set of Recommended Guidelines for Condition Assessment and Evaluation of Existing Bridges in Georgia.

Este trabalho consiste no estudo dos fatores envolvidos no projeto estrutural de pontes, mais especificamente aqueles relacionados com o comportamento dos seus pilares. A análise é efetuada mediante uma modelagem única da estrutura integrada ao maciço de solos, onde as não-linearidades física e geométricas e interação solo-estrutura são consideradas. Inicialmente é feita uma abordagem sobre a concepção do projeto dos pilares e seus arranjos, destacando os problemas diretamente envolvidos no seu cálculo. É apresentada uma formulação simples, baseada em uma só fibra ativa, para levar em consideração a não linearidade física do concreto armado. A não-linearidade geométrica é tratada quanto aos seus aspectos e critérios de utilização, e também é apresentada uma formulação baseada na Energia Potencial Total para a obtenção da matriz de rigidez tangente da estrutura. O maciço de solos é modelado com dispositivos discretos parametrizados através de curvas de resistência lateral p-y. Os aparelhos de apoio são modelados através de elementos de contato devidamente parametrizados. Finalmente, são incluídos alguns exemplos numéricos de casos típicos de pontes / This work deals with the study of factories involved in bridge structural design, specifically in regards with column behavior. The analysis is made by a unique model integrated in the soil massy, where the geometric and physics non-linearity and soil-structure interactions are taken into account. At first, it is made an approach about criteria and details of bridge column design. It is showed a simple formulation; based in one unique active fiber discretization, to consider the physics non-linearity of reinforced concrete Main aspects of geometrical non-linearity are presented. Also it is showed a formulation based in Total Potential Energy in order to obtain the structure tangent stuffiness matrix. The soil massy is modeled with discrete mechanisms by p-y lateral resistance curves. The bearing cushion pads are modeled by contact elements. At end, they are included some numerical examples of bridge typical structures

An increase in the demand for the freight shipping in the United States has been predicted for the near future and Longer Combination Vehicles (LCVs), which can carry more loads in each trip, seem like a good solution for the problem. Currently, utilizing LCVs is not permitted in most states of the US and little research has been conducted on the effects of these heavy vehicles on the roads and bridges. In this research, efforts are made to study these effects by comparing the dynamic and fatigue effects of LCVs with more common trucks. Ten Steel and prestressed concrete bridges with span lengths ranging from 30’ to 140’ are designed and modeled using the grid system in MATLAB. Additionally, three more real bridges including two single span simply supported steel bridges and a three span continuous steel bridge are modeled using the same MATLAB code. The equations of motion of three LCVs as well as eight other trucks are derived and these vehicles are subjected to different road surface conditions and bumps on the roads and the designed and real bridges. By forming the bridge equations of motion using the mass, stiffness and damping matrices and considering the interaction between the truck and the bridge, the differential equations are solved using the ODE solver in MATLAB and the results of the forces in tires as well as the deflections and moments in the bridge members are obtained. The results of this study show that for most of the bridges, LCVs result in the smallest values of Dynamic Amplification Factor (DAF) whereas the Single Unit Trucks cause the highest values of DAF when traveling on the bridges. Also in most cases, the values of DAF are observed to be smaller than the 33% threshold suggested by the design code. Additionally, fatigue analysis of the bridges in this study confirms that by replacing the current truck traffic with higher capacity LCVs, in most cases, the remaining fatigue life of the bridge is only slightly decreased which means that taking advantage of these larger vehicles can be a viable option for decision makers.

Accelerated Bridge Construction (ABC) has gained substantial popularity in new bridge construction and bridge deck replacement because it offers innovative construction techniques that result in time and cost savings when compared to traditional bridge construction practice. One technology commonly implemented in ABC to effectively execute its projects is the use of prefabricated bridge components (precast/prestressed bridge components). Precast/prestressed bridge components are fabricated offsite or near the site and then connected on-site using small volume closure pour connections. Diaphragms are also commonly used to strengthen the connection between certain prefabricated components used in ABC, such as beam elements. Bridges containing closure pour connections and diaphragms can be designed using AASHTO LRFD live-load distribution factor formulas under the condition that the bridge must be sufficiently connected. However, these formulas were developed using analytical models that did not account for the effects of closure pours and diaphragms on live-load distribution. This research study investigates live-load distribution characteristics of precast/prestressed concrete bridges with closure pour connections and diaphragms. The investigation was conducted using finite element bridge models with closure pour joints that were calibrated using experimental data and different configuration of diaphragms. The concrete material used for the closure pour connections was developed as part of a larger project intended to develop high early-strength concrete mixtures that specifically reach strength in only 12 hours, a critical requirement for ABC projects.

Railway noise is a very important and growing health hazard in today´s society.Railway systems pass through towns and cities and create noise. When trainsride through or over railway bridges, switches and crossings the noise increasessubstantially, causing great annoyance to the residents in the area.At the present time, acoustic regulations exist in most countries and are set to achievea good environmental quality in residential areas, schools, hospitals, offices andhotels.A few calculation models exist for railway traffic noise, such as The NPM 1996,NORD2000 and Cnossos-EU. The NPM 1996 is currently used in Sweden to calculatenoise propagation from railway traffic. To uphold the regulations set, it is importantthat the method used is as precise as possible. All of these calculation modelsare based on several correction factors. Today, the current corrections for trackconditions, that is railway bridges, switches and crossings, are not very accurate andneed to be reconsidered.The aim of this project was to investigate and quantify the error of the NPM correctionfactors and give some indication of how they should be adjusted. This is done to makethe noise prediction from railway traffic more accurate and thus protect the residentsfrom these health risks.The specific objective was to perform significant amount of field measurements ofnoise from trains on different steel bridges, switches and crossings, as well as on afew concrete bridge according to the measurement standard Nordtest NT 098. Thefield work was carried out over the period March to May, when weather conditionsmet the criteria for field measurements, in and around the Stockholm area.The results obtained revealed that the correction factors for steel bridges andcrossings are considerably lower in the NPM than measured in this project. However,the correction factors for switches and concrete bridges are similar to the ones inthe NPM. In this thesis, a part of the correction factors have only been invalidatedto a degree. It has been shown that each bridge is unique and perhaps there is apossibility of finding similarities between some type of bridges. However, much moreiv |measurements are needed to see any correlation between each bridge type. Thus,further and more comprehensive measurements have to be carried out in order toestablish new accurate correction factors for track conditions in the Nordic PredictionMethod.

As vigas celulares ocupam um lugar de destaque crescente na construção de pontes em concreto protendido. Dentro desta opção, a tendência moderna é de se construírem pontes unicelulares cada vez mais largas, o que traz como conseqüência um aumento considerável da flexão transversal em seus elementos, especialmente em suas almas, submetendo-as a uma combinação de cisalhamento com flexão transversal que pode atingir valores importantes. Este trabalho tem por finalidade apresentar um novo critério de dimensionamento das almas das vigas de seção celular, incluindo o caso do estado limite último de fadiga. Este critério foi idealizado a partir de uma análise crítica dos modelos vigentes, os quais são analisados e comparados por meio de gráficos de interação relacionando força cortante com flexão transversal, que permitem a escolha da melhor opção para as situações de projeto. Desenvolveu-se uma investigação experimental, a fim de verificar a validade do critério de dimensionamento desenvolvido. Foram analisados os seguintes modos de colapso: esmagamento das bielas comprimidas de concreto, alongamento plástico excessivo dos estribos e ruptura dos estribos por fadiga. Os resultados experimentais mostraram uma boa aproximação do Critério de Dimensionamento Proposto e revelaram novidades nos ensaios de fadiga: a ruptura dos estribos por fadiga se deu por etapas, um estribo de cada vez, num processo gradual. A ruptura por fadiga ocorreu sistematicamente próximo à ligação da alma com a mesa inferior e não no dobramento dos estribos. / Box-girders have received a growing attention in the field of prestressed concrete bridges. The modern trend is to build wider unicellular bridges, which leads to a considerable increase in the transverse bending moment acting mainly in their webs. These are subjected to a combination of shear force and transverse bending moments, which may reach important values. The purpose of this thesis is to introduce a new design approach of box-girder webs, including the Ultimate Limit State due to fatigue. This design approach is derived from a critical analysis of the current criteria. The different criteria for the design of box-girder webs are analyzed and compared by means of shear-bending moment interaction diagrams as an attempt to identify the more realistic one. An experimental investigation has been undertaken with the purpose of verifying the validity of the new developed approach. The following failure modes have been considered: crushing of the compressed struts, excessive plastic deformation of the stirrups and rupture of the stirrups due to fatigue. The experimental results have shown good agreement with those predicted by the proposed approach. Furthermore, the tests have revealed new aspects of the fatigue behavior: the rupture of the stirrups due to fatigue occurred in stages, one at a time in a gradual manner. In all cases the failure took place near the top face of the lower flange and not at the corner of the stirrups.

As vigas celulares ocupam um lugar de destaque crescente na construção de pontes em concreto protendido. Dentro desta opção, a tendência moderna é de se construírem pontes unicelulares cada vez mais largas, o que traz como conseqüência um aumento considerável da flexão transversal em seus elementos, especialmente em suas almas, submetendo-as a uma combinação de cisalhamento com flexão transversal que pode atingir valores importantes. Este trabalho tem por finalidade apresentar um novo critério de dimensionamento das almas das vigas de seção celular, incluindo o caso do estado limite último de fadiga. Este critério foi idealizado a partir de uma análise crítica dos modelos vigentes, os quais são analisados e comparados por meio de gráficos de interação relacionando força cortante com flexão transversal, que permitem a escolha da melhor opção para as situações de projeto. Desenvolveu-se uma investigação experimental, a fim de verificar a validade do critério de dimensionamento desenvolvido. Foram analisados os seguintes modos de colapso: esmagamento das bielas comprimidas de concreto, alongamento plástico excessivo dos estribos e ruptura dos estribos por fadiga. Os resultados experimentais mostraram uma boa aproximação do Critério de Dimensionamento Proposto e revelaram novidades nos ensaios de fadiga: a ruptura dos estribos por fadiga se deu por etapas, um estribo de cada vez, num processo gradual. A ruptura por fadiga ocorreu sistematicamente próximo à ligação da alma com a mesa inferior e não no dobramento dos estribos. / Box-girders have received a growing attention in the field of prestressed concrete bridges. The modern trend is to build wider unicellular bridges, which leads to a considerable increase in the transverse bending moment acting mainly in their webs. These are subjected to a combination of shear force and transverse bending moments, which may reach important values. The purpose of this thesis is to introduce a new design approach of box-girder webs, including the Ultimate Limit State due to fatigue. This design approach is derived from a critical analysis of the current criteria. The different criteria for the design of box-girder webs are analyzed and compared by means of shear-bending moment interaction diagrams as an attempt to identify the more realistic one. An experimental investigation has been undertaken with the purpose of verifying the validity of the new developed approach. The following failure modes have been considered: crushing of the compressed struts, excessive plastic deformation of the stirrups and rupture of the stirrups due to fatigue. The experimental results have shown good agreement with those predicted by the proposed approach. Furthermore, the tests have revealed new aspects of the fatigue behavior: the rupture of the stirrups due to fatigue occurred in stages, one at a time in a gradual manner. In all cases the failure took place near the top face of the lower flange and not at the corner of the stirrups.

There has been increasing interest in evaluating the performance of existing reinforced concrete (RC) bridges just after natural disasters or man-made events especially when the defects are invisible, or in quantifying the improvement after rehabilitations. In order to obtain an accurate assessment of the reliability of a RC bridge, it is critical to incorporate information about its current structural properties, which reflects the possible aging and deterioration. This dissertation proposes to develop an adaptive reliability analysis of RC bridges incorporating the damage detection information obtained from nondestructive testing (NDT). In this study, seismic fragility is used to describe the reliability of a structure withstanding future seismic demand. It is defined as the conditional probability that a seismic demand quantity attains or exceeds a specified capacity level for given values of earthquake intensity. The dissertation first develops a probabilistic capacity model for RC columns and the capacity model can be used when the flexural stiffness decays nonuniformly over a column height. Then, a general methodology to construct probabilistic seismic demand models for RC highway bridges with one single-column bent is presented. Next, a combination of global and local NDT methods is proposed to identify in-place structural properties. The global NDT uses the dynamic responses of a structure to assess its global/equivalent structural properties and detect potential damage locations. The local NDT uses local measurements to identify the local characteristics of the structure. Measurement and modeling errors are considered in the application of the NDT methods and the analysis of the NDT data. Then, the information obtained from NDT is used in the probabilistic capacity and demand models to estimate the seismic fragility of the bridge. As an illustration, the proposed probabilistic framework is applied to a reinforced concrete bridge with a one-column bent. The result of the illustration shows that the proposed framework can successfully provide the up-to-date structural properties and accurate fragility estimates.