No description available.

The new dihydrobis(4-cyano-3-tert-butylpyrazolylborate) ligand has been synthesized. Isolated crystals of the thallium complex were collected and structurally characterized by X-ray diffraction. Transition metal complexes of the ligand are currently under investigation.

Conductive polymer composite sensors have shown great potential in identifying gaseous analytes. To more thoroughly understand the physical and chemical mechanism of this type of sensors, a model was developed by combining two sub-models: a conductivity model and a thermodynamic model, which gives a relationship between the vapor concentration of analyte(s) and the change of the sensor signals. In this work, 64 chemiresistors representing eight different carbon concentrations (8–60 vol.% carbon) were constructed by depositing thin films of a carbon black–polyisobutylene composite onto concentric spiral platinum electrodes on a silicon chip. The responses of the sensors were measured in dry air and at various vapor pressures of toluene and trichloroethylene. Three parameters in the conductivity model were determined by fitting the experimental data. It was shown that by applying this model, the sensor responses can be predicted if the vapor pressure is known; furthermore the vapor concentration can be estimated based on the sensor responses. This model will guide the improvement of the design and fabrication of conductive polymer composite sensors for detecting and identifying organic vapors. A novel method was developed to optimize the selection of polymeric materials to be used within a chemiresistor array for anticipated samples without performing preliminary experiments. It is based on the theoretical predicted responses of chemiresistors and the criterion of minimizing the mean square error (MSE) of the chemiresistor array. After the number of chemiresistors to be used in an array and the anticipated sample chemistry are determined, the MSE values of all combinations of the candidate chemiresistors are calculated. The combination which has the minimum MSE value is the best choice. This can become computationally intensive for selection of polymers for large arrays from candidates in a large database. The number of combinations can be reduced by using the branch and bound method to save computation time. This method is suitable for samples at low concentrations where thermodynamic multi-component interactions are linear. To help users apply this polymer selection method for the sensors, a website including 10 solvents and 10 polymers was developed. Users can specify a target sample and obtain the best set of polymers for a sensor array to detect the sample. The activities of trichloroethylene and toluene in polyisobutylene were measured at very low concentrations. The activities for toluene are consistent with published values at higher concentrations. The values for trichloroethylene are a new contribution to the literature.

No description available.

O objetivo deste estudo foi o desenvolvimento de compósitos poliméricos flexíveis e altamente condutores elétricos preparados por moldagem por compressão e por fabricação de filamentos fundidos (FFF) para possíveis aplicações como materiais piezoresistivos ou piezoelétricos para sensores de compressão. Compósitos baseados em misturas de poli(fluoreto de vinilideno)/poliuretano termoplástico (PVDF/TPU) como matriz e contendo várias frações de negro de fumo-polipirrol (CB-PPy) como aditivo condutor foram preparados. Diversas técnicas de caracterização foram realizadas para avaliar as propriedades mecânicas, térmicas, químicas e elétricas, morfologia e printabilidade dos materiais investigados. Primeiro, blendas de PVDF/TPU com diferentes composições foram produzidas por mistura por fusão seguida de moldagem por compressão. Os resultados mostraram que a flexibilidade desejada para os materiais foi melhorada com a adição de TPU aos compósitos de PVDF. As imagens SEM evidenciaram a obtenção de uma blenda co-contínua com 50/50 vol% de PVDF/TPU. As blendas compostas de PVDF/TPU 38/62 vol% e a blenda co-contínua de PVDF/TPU 50/50 vol% foram selecionadas como matrizes para a preparação de compósitos moldados por compressão e impressos em 3D a fim de alcançar uma ótima combinação entre condutividade, propriedades mecânicas e printabilidade. Várias quantidades de negro de fumo-polipirrol, de 0 a 15%, foram adicionadas às blendas selecionadas para aumentar a condutividade elétrica dos compósitos e possivelmente atuar como agente nucleante para a fase cristalina do PVDF a fim de aumentar sua resposta piezoelétrica. A adição de CB-PPy aumentou a condutividade elétrica de todos os compósitos. No entanto, a condutividade elétrica dos compósitos baseados em blendas co-contínuas PVDF/TPU 50/50 vol% foi maior do que as encontradas para os compósitos de PVDF/TPU 38/62 vol% com mesma concentração de aditivo. De fato, o limiar de percolação elétrico dos compósitos com blenda co-contínua foi de 2%, enquanto o limiar de percolação elétrico dos compósitos compostos da blenda não contínua foi de 5%. Com relação às propriedades mecânicas, a incorporação do aditivo condutor nas blendas resultou em materiais mais rígidos com maior módulo de elasticidade, menor alongamento na ruptura e maior módulo de armazenamento. O módulo de armazenamento (G') e a viscosidade complexa (η*) dos compósitos aumentaram com a adição de CB-PPy. O limiar de percolação reológico foi de 3% para PVDF/TPU/CB-PPy 38/62 vol% e 1% para PVDF/TPU/CB-PPy 50/50 vol%, indicando que uma quantidade maior de carga poderia comprometer a processabilidade dos compósitos. A adição de CB-PPy também resultou na redução dos valores de Tg e Tm dos compósitos devido à redução da mobilidade das cadeias poliméricas. Com base na condutividade elétrica e no comportamento mecânico dos compósitos, três composições diferentes foram selecionadas para a extrusão de filamentos para serem posteriormente utilizados no processo de impressão 3D. No geral, as peças impressas em 3D apresentaram propriedades mecânicas e elétricas inferiores devido à presença de vazios, defeitos e camadas sobrepostas que podem dificultar o fluxo de elétrons. Os valores de condutividade elétrica dos compósitos impressos em 3D de PVDF/TPU/CB-PPy 38/62 vol% contendo 5% e 6% de CB-PPy são de uma a sete ordens de grandeza menores do que os encontrados para os compósitos com a mesma composição moldados por compressão. Mesmo que o valor da condutividade elétrica para o compósito PVDF/TPU 38/62 vol% com 6% de CB-PPy moldado por compressão foi de 1,94x10-1 S•m-1, o compósito impresso em 3D com a mesma composição mostrou um valor muito baixo de condutividade elétrica de 6,01x10-8 S•m-1. Por outro lado, o compósito co-contínuo de PVDF/TPU 50/50 vol% com 10% de aditivo impresso em 3D apresentou um alto valor de condutividade elétrica de 4,14×100 S•m-1 mesmo após o processo de impressão. Além disso, as respostas piezoresistivas dos compósitos foram investigadas. Para os compósitos PVDF/TPU/CB-PPy 38/62 vol%, as amostras moldadas por compressão e impressas em 3D com 5% e 6% de CB-PPy exibiram boa resposta piezoresistiva. No entanto, apenas os compósitos com 6% de aditivo apresentaram valores elevados de sensibilidade e gauge factor, atuação em ampla faixa de pressão e respostas piezoresistivas reprodutíveis durante a aplicação de 100 ciclos de compressão/descompressão para ambos os métodos de fabricação. Por outro lado, para os compósitos co-contínuos de PVDF/TPU/CB-PPy apenas a amostra moldada por compressão com 5% de CB-PPy apresentou respostas piezorresistivas boas e reprodutíveis. A cristalinidade e o teor de fase β do PVDF foram investigados para os compósitos. Embora o grau de cristalinidade das amostras tenha diminuído com a adição de CB-PPy, a porcentagem de fase β no PVDF aumentou. O coeficiente piezoelétrico d33 das amostras aumentou com a porcentagem de fase β. A adição de 6% ou mais de CB-PPy foi necessária para aumentar significativamente o coeficiente piezoelétrico (d33) dos compósitos. O conteúdo de fase β e as respostas piezoelétricas do PVDF foram menores para as amostras preparadas por FFF. Por fim, como pesquisa colateral, a eficiência de blindagem contra interferência eletromagnética (EMI-SE) foi medida para todos os compósitos. Compósitos com maior condutividade elétrica apresentaram melhor blindagem da radiação eletromagnética. Além disso, os compósitos baseados na blenda co-contínua apresentaram maior eficiência de blindagem contra EMI do que os compósitos de PVDF/TPU 38/62 vol%. O principal mecanismo de blindagem foi a absorção para todos os compósitos. As amostras preparadas por FFF apresentaram respostas de EMI-SE menores quando comparadas às amostras moldadas por compressão. / The aim of this study was the development of flexible and highly electrically conductive polymer composites via compression molding and fused filament fabrication for possible applications as piezoresistive or piezoelectric materials for pressure sensors. Composites based on blends of poly(vinylidene fluoride)/thermoplastic polyurethane (PVDF/TPU) as matrix and containing various fractions of carbon black-polypyrrole (CB-PPy) as conductive filler were prepared. Several characterization techniques were performed in order to evaluate the mechanical, thermal, chemical and electrical properties, morphology and printability of the investigated materials. First, PVDF/TPU blends with different compositions were prepared by melt compounding followed by compression molding. The results showed that the flexibility aimed for the final materials was improved with the addition of TPU to PVDF composites. SEM images evidenced the achievement of a co-continuous blend comprising 50/50 vol% of PVDF/TPU. The blends composed of PVDF/TPU 38/62 vol% and the co-continuous blend of PVDF/TPU 50/50 vol% were selected as matrices for the preparation of compression molded and 3D printed composites in order to achieve an optimal compromise between electrical conductivity, mechanical properties and printability. Various amounts of carbon black-polypyrrole, from 0 up to 15%, were added to the selected blends in order to rise the electrical conductivity of the composites and to possible act as nucleating filler for the β crystalline phase of PVDF in order to increase its piezoelectric response. The addition of CB-PPy increased the electrical conductivity of all composites. However, the electrical conductivity of composites based on PVDF/TPU 50/50 vol% co-continuous blends was higher than those found for PVDF/TPU 38/62 vol% composites at the same filler content. Indeed, the electrical percolation threshold of the conductive co-continuous composite blends was 2%, while the electrical percolation threshold of the composites with the nonco-continuous composite blends was 5%. With respect to the mechanical properties, the incorporation of the filler into the blends leaded to more rigid materials with higher elastic modulus, lower elongation at break and higher storage modulus. The storage modulus (G’) and complex viscosity (η*) of the composites increased with the addition of CB-PPy. The rheological percolation threshold was found to be 3% for PVDF/TPU/CB-PPy 38/62 vol% and 1% for PVDF/TPU/CB-PPy 50/50 vol%, indicating that higher amount of filler could compromise the processability of the composites. The addition of CB-PPy also resulted in a reduction on the Tg and Tm values of the composites due to the reduction of the mobility of the polymeric chains. Based on the electrical conductivity and mechanical behavior of the composites, three different compositions were selected for the extrusion of filaments to be used in a 3D printing process. Overall, the 3D printed parts presented lower mechanical and electrical properties because of the presence of voids, defects and overlapping layers that can hinder the flow of electrons. The electrical conductivity values of PVDF/TPU/CB-PPy 38/62 vol% composites containing 5% and 6 wt% of CB-PPy 3D printed samples are one to seven orders of magnitude lower than those found for compression molded composites with the same composition. Even if the electrical conductivity value for PVDF/TPU 38/62 vol% compression molded composite with 6% of CB-PPy was as high as 1.94x10-1 S•m-1, the 3D printed composite with same composition showed a very low electrical conductivity of 6.01x10-8 S•m-1. On the other hand, the 3D printed co-continuous composite PVDF/TPU 50/50 vol% with 10% of filler displayed a high value of electrical conductivity of 4.14×100 S•m-1 even after the printing process. Moreover, the piezoresistive responses of the composites were investigated. For PVDF/TPU/CB-PPy 38/62 vol% composites, the compression molded and 3D printed samples with 5% and 6% of CB-PPy exhibited good piezoresistive response. However, only the composites with 6% displayed high sensitivity and gauge factor values, large pressure range and reproducible piezoresistive responses under 100 cycles for both methods. On the other hand, for PVDF/TPU/CB-PPy co-continuous composites only the compression molded sample with 5% of CB-PPy presented good and reproducible piezoresistive responses. The crystallinity and β phase content of PVDF were investigated for the composites. Althought the degree of crystallinity of the samples decreased with the addition of CB-PPy, the percentage of β phase in PVDF was increased. The piezoelectric coefficient d33 of the samples increased with the percentage of β phase. The addition of 6% or more of CB-PPy was necessary to increase significatively the piezoelectric coefficient (d33) of the composites. The β phase content and piezoelectric responses of PVDF were lower for samples prepared by FFF. Finally, as a collateral research, the electromagnetic interference shielding effectiveness (EMI-SE) were measured for all composites. Composites with higher electrical conductivity showed better shielding of the electromagnetic radiation. In addition, composites based on the co-continuous blend displayed higher EMI shielding efficiency than 38/62 vol% composites. The main mechanism of shielding was absorption for all composites. Specimens prepared by FFF displayed diminished EMI-SE responses when compared to compression molded samples. / Lo scopo di questo studio è lo sviluppo di compositi polimerici flessibili e ad elevata conducibilità elettrica tramite stampaggio a compressione e manifattura additiva (fused filament fabrication) per possibili applicazioni come materiali piezoresistivi o piezoelettrici in sensori di pressione. In particolare, sono stati preparati compositi a base di miscele di poli(vinilidene fluoruro)/poliuretano termoplastico (PVDF/TPU) come matrice e contenenti varie frazioni di nerofumo-polipirrolo (CB-PPy) come riempitivo conduttivo. Sono state utilizzate diverse tecniche di caratterizzazione al fine di valutare le proprietà meccaniche, termiche, chimiche ed elettriche, la morfologia e la stampabilità dei materiali ottenuti. In primo luogo, miscele PVDF/TPU con diverse composizioni sono state preparate mediante mescolatura allo stato fuso seguita da stampaggio a compressione. I risultati hanno mostrato che la flessibilità del PVDF viene notevolemente migliorata dall’aggiunta di TPU. Le immagini SEM hanno evidenziato il raggiungimento di una miscela co-continua per una composizione 50/50% in volume di PVDF/TPU. Le miscele composte da PVDF/TPU 38/62 vol% e la miscela co-continua di PVDF/TPU 50/50 vol% sono state selezionate come matrici per la preparazione di compositi per stampaggio a compressione e manifattura additiva al fine di ottenere un compromesso ottimale tra conducibilità, proprietà meccaniche e stampabilità. Alle miscele selezionate sono state aggiunte varie quantità di nerofumo-polipirrolo, dallo 0 al 15%, per aumentare la conducibilità elettrica dei compositi ed eventualmente fungere da additivo nucleante per la fase β cristallina del PVDF al fine di aumentarne la risposta piezoelettrica. L'aggiunta di CB-PPy ha aumentato la conduttività elettrica di tutti i compositi. Tuttavia, la conduttività elettrica dei compositi basati su miscele co-continue di PVDF/TPU 50/50% in volume era superiore a quella trovata per compositi PVDF/TPU 38/62% in volume con lo stesso contenuto di riempitivo. Infatti, la soglia di percolazione elettrica delle miscele conduttive era del 2%, mentre la soglia di percolazione elettrica dei compositi con miscele composite non continue era del 5%. Per quanto riguarda le proprietà meccaniche, l'incorporazione del riempitivo nelle mescole ha portato a materiali più rigidi con modulo elastico più elevato, allungamento a rottura inferiore e modulo conservativo più elevato. Il modulo conservativo (G') e la viscosità complessa (η*) dei compositi sono aumentate con l'aggiunta di CB-PPy. La soglia di percolazione reologica è risultata essere del 3% per PVDF/TPU/CB-PPy 38/62 vol% e dell'1% per PVDF/TPU/CB-PPy 50/50 vol%, indicando che una maggiore quantità di riempitivo potrebbe compromettere la processabilità dei compositi. L'aggiunta di CB-PPy ha comportato anche una riduzione dei valori di Tg e Tm dei compositi a causa della riduzione della mobilità delle catene polimeriche. Sulla base della conduttività elettrica e del comportamento meccanico dei compositi, sono state selezionate tre diverse composizioni per l'estrusione di filamenti da utilizzare in un processo di stampa 3D. Nel complesso, le parti stampate in 3D presentavano proprietà meccaniche ed elettriche inferiori a causa della presenza di vuoti, difetti e strati sovrapposti che possono ostacolare il flusso di elettroni. I valori di conducibilità elettrica dei compositi PVDF/TPU/CB-PPy 38/62 vol% contenenti il 5% e il 6% di CB-PPy di campioni stampati in 3D sono da uno a sette ordini di grandezza inferiori a quelli trovati per i compositi stampati a compressione con la stessa composizione. Anche se il valore di conducibilità elettrica per il composito stampato a compressione PVDF/TPU 38/62 vol% con il 6% di CB-PPy era pari a 1,94x10-1 S•m-1, il composito stampato in 3D con la stessa composizione ha mostrato un valore molto basso di conducibilità elettrica, pari a 6,01x10-8 S•m-1. D'altra parte, il composito PVDF/TPU 50/50 vol% stampato in 3D con il 10% di riempitivo ha mostrato un elevato valore di conducibilità elettrica, pari a 4,14 × 100 S•m-1, anche dopo il processo di stampa. Inoltre, sono state studiate le risposte piezoresistive dei compositi. Per i compositi PVDF/TPU/CB-PPy 38/62 vol%, i campioni stampati a compressione e stampati in 3D con il 5% e il 6% di CB-PPy hanno mostrato una buona risposta piezoresistiva. Tuttavia, solo i compositi con il 6% hanno mostrato valori di sensibilità e gauge factor elevati, ampio intervallo di pressione e risposte piezoresistive riproducibili in 100 cicli per entrambi i metodi. D'altra parte, per i compositi co-continui PVDF/TPU/CB-PPy solo il campione stampato a compressione con il 5% di CB-PPy ha presentato risposte piezoresistive adeguate e riproducibili. La cristallinità e il contenuto di fase β del PVDF sono stati studiati per i compositi. Sebbene il grado di cristallinità dei campioni diminuisca con l'aggiunta di CB-PPy, la percentuale di fase β in PVDF risulta aumentata. Il coefficiente piezoelettrico d33 dei campioni aumenta anch’esso con la percentuale di fase β. L'aggiunta del 6% o più di CB-PPy è stata necessaria per aumentare significativamente il coefficiente piezoelettrico (d33) dei compositi. Il contenuto di fase β e le risposte piezoelettriche del PVDF sono inferiori per i campioni ottenuti mediante stampa 3D. Infine, come ricerca collaterale, è stata misurata l'efficacia della schermatura contro le interferenze elettromagnetiche (EMI-SE) per tutti i compositi. I compositi con una maggiore conduttività elettrica hanno mostrato una migliore schermatura della radiazione elettromagnetica. Inoltre, i compositi basati sulla miscela co-continua hanno mostrato un'efficienza di schermatura EMI maggiore rispetto ai compositi a 38/62% in volume. Per tutti i compositi, il principale meccanismo di schermatura è l'assorbimento. I campioni preparati mediante manifattura additiva hanno mostrato risposte EMI-SE inferiori rispetto ai campioni stampati a compressione.

La thèse porte de manière générale sur les polymères électrostrictifs qui peuvent être utilisés soit comme actionneurs électromécaniques souples, soit comme capteurs ou récupérateurs d’énergie. Le premier chapitre est une introduction générale aux systèmes couplés électromécaniques. Le choix des matériaux est exposé et porte sur les élastomères diélectriques et les polyuréthanes (PU) chargés par des nanoparticules conductrices de noir de carbone (CB). Le second chapitre porte sur la réalisation des films. Des particules de CB sous forme de micelles préformées et une technique « solution-cast » sont employées dans cette optique. Ce procédé permet une bonne dispersion des charges. Une amélioration de la déformation d’un facteur 1,6 est obtenue par introduction de particules de CB à 0.89 vol%. Le troisième chapitre présente la modélisation de phénomènes comme la saturation de la polarisation qui implique directement une saturation de la déformation. En modélisant la polarisation comme une fonction non-linéaire dépendant de deux variables (la permittivité bas niveau et un champ de saturation), on décrit ainsi correctement plusieurs phénomènes qui ne peuvent être interprétés par une approche linéaire et homogène. Les simulations effectuées montrent une bonne corrélation avec les expérimentations menées. Le quatrième chapitre propose une comparaison entre les films PU purs et chargés. Cette analyse porte non seulement sur des mesures mécaniques et électriques mais également en XRD ou en DSC afin de détecter le niveau de cristallisation. Une dispersion importante a ainsi été observée visuellement. Des déformations de l’ordre de 50 % ont ainsi été obtenues. Le cinquième chapitre porte sur l’effet lié à l’injection de charges électriques par bombardement électronique (HEBI), sur la déformation électrostrictive. Une telle approche permet ainsi un gain d’un facteur de l’ordre de 2 sur la déformation et semble réduire les pertes de façon très conséquente. / In a general manner, the present thesis focuses on electrostrictive polymers which can be used either as flexible electromechanical actuators or as sensors or energy harvesters. Chapter 1 is a general introduction to electro-mechanical coupled systems. The choice of the materials is described and focuses on dielectric elastomers, polyurethane (PU) with conductive carbon black (CB) nano-particle fillers. Chapter 2 focuses on the film synthesis. CB nano-particles in the form of micelles and solution cast method were employed to provide good filler dispersion. The strain enhancement of a factor of 1.6 was obtained by 0.89 vol% CB doping. Chapter 3 exposes the modeling of electrostrictive actuation and in particular the saturation of the polarization. By modeling the polarization as a nonlinear function depending on two variables (low-level permittivity and saturation field), it is therefore possible to describe several phenomena that cannot be explained by a classical linear and homogeneous approach. Simulations performed using such an approach show a good agreement with experimental results. Chapter 4 presents the comparison between pure PU and composite films. It includes mechanical/electrical characterization as well as XRD or DSC measurements to detect the crystallization level. High dispersion level was visually confirmed. Strains of the order of 50 % were reached. Chapter 5 deals with the effect of electric charge injection by homogeneous electron beam irradiation (HEBI) on the electrostrictive strain. This technique therefore permits a gain of 2 on the obtained strain and seems to significantly reduce the losses in the material as well.

The aim of this study was to improve the mechanical and electrical properties of conductive polymer composites. For this purpose, different studies were performed in this dissertation. In order to investigate the effects of the carbon nanotube (CNT) surface treatment on the morphology, electrical and mechanical properties of the composites, poly(ethylene terephthalate) (PET) based conductive polymer composites were prepared by using as-received, purified and modified carbon nanotubes in a twin screw extruder. During the purification of carbon nanotubes, surface properties of carbon nanotubes were altered by purifying them with nitric acid (HNO3), sulfuric acid (H2SO4), ammonium hydroxide (NH4OH) and hydrogen peroxide (H2O2) mixtures. Electron Spectroscopy for Chemical Analysis (ESCA) results indicated the removal of metallic catalyst residues from the structure of carbon nanotubes and increase in the oxygen content of carbon nanotube surface as a result of purification procedure. Surface structure of the purified carbon nanotubes was also modified by treatment with sodium dodecyl sulfate (SDS), poly(ethylene glycol) (PEG) and diglycidyl ether of Bisphenol A (DGEBA). Fourier Transformed Infrared Spectroscopy (FTIR) spectra of the carbon nanotube samples indicated the existence of functional groups on the surfaces of carbon nanotubes after modification. All composites prepared with purified and modified carbon nanotubes had higher electrical resistivities, tensile and impact strength values than those of the composite based on as-received carbon nanotubes, due to the functional groups formed on the surfaces of carbon nanotubes during surface treatment. In order to investigate the effects of alternative composite preparation methods on the electrical and mechanical properties of the composites, in-situ microfiber reinforced conductive polymer composites consisting of high density polyethylene (HDPE), poly(ethylene terephthalate) and carbon nanotubes were prepared in a twin screw extruder followed by hot stretching of PET/CNT phase in HDPE matrix. Composites were produced by using as-received, purified and PEG treated carbon nanotubes. SEM micrographs of the hot stretched composites pointed out the existence of in-situ PET/CNT microfibers dispersed in HDPE matrix up to 1 wt. % carbon nanotube loadings. Electrical conductivity values of the microfibrillar composites were higher than that of the composites prepared without microfiber reinforcement due to the presence of continuous PET/CNT microfibers with high electrical conductivity in the structure. To investigate the potential application of conductive polymer composites, the effects of surfactant usage and carbon nanotube surface modification / on the damage sensing capability of the epoxy/carbon nanotube/glass fiber composite panels during mechanical loadings were studied. Surface modification of the carbon nanotubes was performed by using hexamethylene diamine (HMDA). 4-octylphenol polyethoxylate (nonionic) (Triton X-100) and cetyl pyridinium chloride (cationic) (CPC) were used as surfactants during composite preparation. Electrical resistivity measurements which were performed during the impact, tensile and fatigue tests of the composite panels showed the changes in damage sensing capabilities of the composites. Surface treatment of carbon nanotubes and the use of surfactants decreased the carbon nanotube particle size and improved the dispersion in the composites which increased the damage sensitivity of the panels.

Orientador: Darcy Hiroe Fujii Kanda / Banca: Luiz Francisco Malmonge / Banca: Dante Luis Chinaglia / Resumo: Compósitos poliméricos condutores, também chamados de polímeros condutores extrínsecos, têm sido alvo de intensa pesquisa científica devido ao seu grande potencial de aplicação nos mais diversificados setores industriais. Esses materiais combinam as características de um polímero (leveza, flexibilidade, fácil processamento) com as de cargas condutoras (alta condutividade). O poliuretano derivado de óleo de mamona (PUR) é um polímero obtido pela mistura de pré-polímero e poliol (derivado de óleo de mamona) que apresenta grande potencial para ser utilizado como matriz polimérica em compósitos. Ele possui propriedades equivalentes aos dos poliuretanos (PU) convencionais e tem como vantagem ser um polímero biodegradável e proveniente de fonte renovável. Em relação às cargas condutoras, o negro de fumo (NF) é um dos materiais mais utilizados para esse fim, enquanto que pouco se encontra na literatura sobre o carvão ativado nano em pó (CANP), mesmo possuindo estrutura semelhante e maior condutividade que o NF. Neste contexto, o presente trabalho tem como objetivo viabilizar os processos de síntese e fazer a caracterização elétrica dos compósitos poliuretano derivado de óleo de mamona/carvão ativado nano em pó (PUR/CANP) e poliuretano derivado de óleo de mamona/negro de fumo (PUR/NF) na forma de filmes pelo método "casting", mantendo fixa a razão pré-polímero/poliol e variando a fração de volume de CANP e NF. A análise térmica foi feita por Calorimetria Diferencial de Varredura (DSC), o estudo da condutividade dc e ac foram feitas pelo Método de Duas Pontas (tensão x corrente) (MDP) e pela técnica de Espectroscopia de Impedância Elétrica (EIE), respectivamente, e a análise morfológica foi feita em Microscópio Eletrônico de Varredura com canhão de elétrons por... (Resumo completo, clicar acesso eletrônico abaixo) / Abstract: Conductive polymer composites, also called extrinsic conducting polymers, has been the subject of intense scientific research due to its great potential for industrial application. These materials combine the characteristics of a polymer (lightness, flexibility, easy processing) with the conductive fillers (high conductivity). The castor oil based polyurethane (PUR) is a polymer obtained from pre-polymer and polyol (based castor oil) mixing which has great potential to be used as matrix polymer in composites. It has properties equivalent to those of conventional polyurethane (PU) and has the advantage of being a biodegradable polymer and from a renewable source. In relation to conductive fillers, carbon black (CB) is one of the most widely used materials for this purpose, while in the literature there are few data about activated carbon nanopowder (ACNP), despite having similar structure and that the higher conductivity than CB. In this context, this work aims to provide the synthesis processes and electrically characterize of composite castor oil based polyurethane/activated carbon nanopowder (PUR/ACNP) and castor oil based polyurethane/carbon black (PUR/CB) in the form of films by casting, keeping the ratio pré-polímero/poliol fixed and varying the volume fraction ACNP and CB. The sample were characterized using Differential Scanning Calorimetry (DSC), Two Points Method (voltage x current) (TPM), Electrical Impedance Spectroscopy (EIS) and Scanning Electron Microscope with electron gun for field emission (FEG-SEM). DSC results showed that the glass transition temperature (Tg) of composites do not depend of type or volume fraction of conductive fillers. The results of electrical analysis showed that the samples of PUR/CB have lower percolation threshold than those of PUR/ACNP (20% vs. 40%). This result is due the distribution... (Summary complete electronic access click below) / Mestre

Les matériaux hybrides organique/inorganiques ont reçu beaucoup d'attention ces dernières années dans les études des nanomatériaux. En effet, ils possèdent des propriétés physiques et chimiques uniques grâce aux effets synergiques de chaque composant. En particulier, les nanoparticules de silice (SiO2) présentent des caractéristiques intéressantes, comme une bonne stabilité chimique et thermique. Elles peuvent être préparées de différentes tailles et peuvent aussi être facilement fonctionnalisées. Les polymères conducteurs intrinsèques comme le polythiophène et la polyaniline (PANI) peuvent exister sous différents états d'oxydation et donc répondre à des stimuli extérieurs en changeant une de leur caractéristique (couleur, conductivité, etc…). La PANI est un polymère non-toxique, thermiquement stable et peu coûteux avec une conductivité relativement élevée qui a été utilisée comme film antistatique, matériel d'électrode, inhibiteur de corrosion et comme surface sensible de capteur. Depuis la découverte des polymères conducteurs en 1977, plusieurs travaux ont été effectués sur la préparation, la caractérisation et les applications de films polymériques construits à la surface de matériaux comme la silice. Parmi les différents types de composites existants, les particules de type cœur@coquille composées d’un cœur inorganique et d’une couronne de polymère sont les plus prometteurs. Dans cette étude, nous avons donc décidé de travailler sur la synthèse de composites cœur@coquille constitués d’une coquille de PANI et d’un cœur de particules de silice.Dans la littérature, en utilisant des protocoles expérimentaux similaires, deux morphologies très contradictoires ont été obtenues après la polymérisation par oxydation chimique d'aniline en présence de particules de silice : cœur@coquille et framboise (structure inversée avec la PANI comme cœur). Nous avons alors décidé de réexaminer la synthèse de PANI en présence de particules de silice. Pour cela, nous avons, dans un premier temps, synthétisé des particules de silice monodisperses de différentes tailles (300, 160 et 90 nm) par procédé Stöber. Nous avons ensuite réalisé la polymérisation chimique de l'aniline en présence de ces particules de silice dans des conditions contrôlées afin de promouvoir une adsorption des ions aniliniums en surface des particules. Différents paramètres expérimentaux ont été étudiés tels que la température, la concentration en réactifs, la taille des particules… Les résultats en termes de morphologie sont discutés en fonction de ces paramètres. Dans un second temps, nous avons fonctionnalisé la surface des particules de silice par un alcoxysilane afin de favoriser la polymérisation de l’aniline à la surface des particules. Ainsi, nous avons obtenu des structures SiO2@PANI avec une épaisseur de polymère contrôlable. La dernière partie de ce travail traite des premiers essais qui ont été réalisés afin d’utiliser ces composites SiO2@PANi pour des applications environnementales. Deux applications ont notamment été envisagées, l'adsorption de métaux pour l'aspect de particule et la détection de gaz pour les capacités conductrices de la PANI. / Organic/inorganic hybrid materials have received much attention in recent years such as in the field of nano-materials. Indeed, these materials possess unique physical and chemical properties due to the synergistic effect of both components. In particular, silica nanoparticles (SiO2) present interesting properties, such as good chemical and thermal stabilities. They can be prepared in different size and can be easily chemically modified. Intrinsically conducting polymers such as polythiophene and polyaniline (PANI) can exist in different oxidation states and respond to external stimuli by changing one of their characteristics (color, conductivity, …). PANI is a non-toxic, thermally stable and low cost polymer with relatively high conductivity that has been used as antistatic coating, electrode materials, corrosion inhibitor and active layer of sensors. Since the discovery of conducting polymer in 1977, several works have been carried out on the preparation, characterization and applications of polymeric films build on various surfaces like silica. Among the different kinds of composites that exist, inorganic-polymer core-shell nanoparticles are more promising candidates. In this study, we decided to work on the synthesis of core@shell hybrid compounds based on PANI shells and silica nanoparticles cores.In the literature, using similar experimental protocols, two morphologies have been obtained after chemical polymerization of aniline in the presence of silica particles: core@shell and raspberry (inverted structure with PANI as core). We thus decided to reinvestigate the synthesis of PANI in the presence of silica particles. For this, we first synthesized silica particles with different sizes by Stöber process. We then performed the chemical polymerization of aniline in the presence of these naked silica particles under different conditions: temperature, concentration of reactive. However, in all cases, we never managed to obtain core@shell structures. Finally, we succeed in developing a method to prepare these core@shell particles which relies on the functionalization of the SiO2 by alkoxysilanes followed by the polymerization of aniline at room temperature. A series of core-shell particles with tunable PANI thickness has been prepared by this method. The last part of this work deals with the first tests that have been carried out in order to use these composites SiO2@PANi for environmental applications. Two applications have been considered, the adsorption of metals for the particle appearance and the detection of gas for the conductive capacities of the PANI.

Cette thèse a pour but de contribuer à la mise au point et le développement, de plaques mono ou bipolaires composites pour piles à combustibles à membranes échangeuses de protons (ou PEMFC). Les plaques mono ou bipolaires (selon le type de refroidissement choisi) sont un élément essentiel au fonctionnement des piles car elles l’alimentent en gaz réactifs (hydrogène et oxygène de l’air), assurent la tenue mécanique des cellules, la séparation des compartiments anodique et cathodique, le collectage des électrons, et l’évacuation des « sous-produits » eau et chaleur. L’optimisation des propriétés physico-chimiques et mécaniques des plaques, et de leur procédé d’élaboration, permettra de rendre de ce fait la technologie pile à combustible plus accessible Après une étude bibliographique centrée sur les systèmes composites à taux de charges ou de renforts élevé et leurs propriétés physicochimiques, mécaniques et électriques, la 2ème phase sera axée sur une contribution à l’optimisation des formulations par des analyses morphologiques, physiques et physicochimiques pertinentes. La 3ème phase sera dédiée à l’analyse des plaques mono ou bipolaires après tests en piles afin de permettre des choix entre les différentes formulations ou procédés de mise en œuvre des plaques mono et bipolaires et dégager des paramètres pertinents reliés aux propriétés d’usage et à leur évolution au cours du temps en conditions réelles d’utilisation. / The objective of this work is to design carbon polymer composites for bipolar plates, with high and homogeneous electrical and mechanical properties. A method was designed in order to analyze the electrical conductivity homogeneity of the bipolar plates. Several designs of experiments were formulated after optimization of the most influencing formulation parameters on the use properties. This first step enhanced the use properties of the resulting materials, though insufficiently. The plates characterization showed highly heterogeneous and anisotropic use properties. The fabrication process conditions optimization (thermosets formulations) and the addition of an annealing step (thermoplastic formulations) then improved significantly the use properties and their homogeneity.