The thesis is focused on design the switching power supply according to Push-pull topology rules. The work describes basic theoretic principles of Push-pull topology with design of circuit and circuit elements.

This Master’s thesis is focused on design of voltage converter’s system operating with supply voltage of batteries. There are selected appropriate types of batteries, converter topologies and modes of their control. The specified output branches are systematically divided into three separate modules. Each module is designed in detail with focus on high efficiency. The modules are implemented and optimized. Parameter of final modules were measured and compared with correctness of design and theoretical assumptions.

This diploma thesis deals with a design layout of the fan power supply that ensures the increase of the efficiency of the heating unit. For usage in the areas without electric power, the power supply is secured by thermoelectric generator. The system has to function on the basis of autonomous system which turns itself on only when necessary. In the introductory part of the paper there is a recherché of thermoelectric generators for general usage. Next it mentions the basic findings in from the field of DC/DC converters for low power applications. In this part attention is given to MPPT algorithm. Furthermore basic knowledge from the field of heat transmission together with its most used elements is described. Subsequently existing applications that increase the effectiveness of heating are mentioned. Their disadvantage however is that they depend on the external source of power supply. The practical part to a large extent covers the analysis of the suitability of the chosen thermoelectric module. For securing of the heat gradient of the generator there was a model created meeting the figures in the manual and there are several simulations in the MATLAB program. Furthermore several measurements of the thermoelectric module took place in order to secure realistic figures. Subsequently a DC/DC converter was chosen. Finally the testing was made on the real composition. In conclusion there is an overall evaluation including the real usage and the economical aspect of the project. The outcomes of the work enable to avoid common mistakes that are part of many specialized articles. The created system is to be used after the adjustment of the cooling to the required aim. At the same time it becomes very effective.

Tato diplomová práce se zabývá vývojem autonomního zdroje elektrické energie založeného na MEMS termoelektrickém generátoru. Uvažovaný generátor bude následně použit pro napájení autonomní senzorické jednotky pro letecké aplikace. Systémový pohled na autonomní senzorickou jednotku zahrnuje senzor se zpracováním a přenosem dat, energy harvester (termoelektrický generátor), power management, akumulační prvek a autodiagnostiku. Všechny výše uvedené komponenty jsou v práci podrobně popsány. V úvodu práce je provedena široká rešerše existujících termoelektrických generátorů pro letecké aplikace. Následně jsou popsány základní teoretické poznatky z oblasti DC/DC měničů pro energy harvesting. Zvláštní pozornost je věnována metodám MPPT (Maximum Power Point Tracking). Jako základ pro vývoj napájení autonomní senzorické jednotky bylo provedeno množství simulací za pomoci nástroje MATLAB/Simulink Simscape. Pro identifikaci prametrů modelu posloužilo měření na speciálním přípravku. Praktická implementace teoreticky popsaných problémů je provedena na k tomuto účelu navrženém technologickém demonstrátoru. Závěrem je zhodnocena reálná využitelnost navržené technologie pro finální aplikaci v leteckém průmyslu.

This thesis describes energy consumption and power supplying low-power IoT devices. There is general analysis of current consumption and selecting suitable primary battery cell depends of behavior battery type. The next point is analysis of low-power and high-effectivity DC/DC convertor’s feature. The second part contains available solutions for energy monitoring and current measurement. This thesis also contains design of device for measure these energy consumption, with user application, which interprets measured data.

Ce travail concerne l'étude théorique,l’analyse numérique et la validationexpérimentale d'une topologie de convertisseurd’électronique de puissance basée sur unconvertisseur multiniveau modulaire entrelacéavec transformateur moyenne fréquence.L’architecture est adaptée pour l’étage deconversion AC-DC dans les applications detransformateur d'électronique de puissance pourla connexion entre un réseau alternatif moyennetension et un réseau continu basse tension.L’entrelacement réduit les pertes par conductiondans les interrupteurs. Le transformateurmoyenne fréquence 10 kHz assure une isolationgalvanique et connecte le convertisseurmultiniveau modulaire entrelacé à unconvertisseur pont complet. Avec comme pointde départ la structure, le principe defonctionnement, la modélisation, la technique demodulation et le schéma de commande sontdiscutés. Une caractéristique du convertisseur estla génération simultanée de la tension du réseaubasse fréquence et de la tension primaire dutransformateur moyenne fréquence.L'équilibrage de la tension des condensateurs etla minimisation du courant de circulation sontcombinés dans un seul algorithme. La commanderégule le courant alternatif et la tension du buscontinu, du côté haute tension, ainsi que latension continue et le flux de puissance, du côtébasse tension. La validation expérimentale duconvertisseur est réalisée avec un prototype de720 W monophasé à l’échelle réduite. Lesrésultats démontrent la stabilité du système decommande lors d'opérations en régimepermanent et dynamiques (pas de charge,inversion du flux de puissance). / This work aims to present thetheoretical study, the numerical analysis and theexperimental validation of a power electronicsconverter topology based on an interleavedmodular multilevel converter with mediumfrequencytransformer. The architecture issuitable for the AC-DC stage in solid-statetransformer applications for the connectionbetween a medium-voltage AC grid and a lowvoltageDC grid. The interleaving reduces theswitch conduction losses. The 10 kHz mediumfrequencytransformer provides galvanicisolation and connects the interleaved modularmultilevel converter to a full-bridge converter.From the converter structure, the principle ofoperation, the modeling, the modulationtechnique, and the control scheme are discussed.One feature of the converter is the simultaneousgeneration of the low-frequency grid voltageand the medium-frequency transformer primaryvoltage. The capacitor voltage balancing and thecirculating currents minimization are combinedtogether in a single algorithm. The controlsystem regulates the AC current and the DC busvoltage, on the high-voltage side, and the DCvoltage and power flow, on the low voltage side.The experimental validation of the converter ismade with a scaled-down single-phase 720 Wprototype. The results demonstrate the controlsystem stability in steady-state and dynamic(load step, power flow inversion) operations.

No description available.

In sustainable energy systems those using fuel cells, high step-up gain converters are widely used to increase the output voltage to levels that can be used by other converters, such as inverters for grid connection or powering other AC loads. In order to obtain a higher voltage gain, in comparison to a traditional boost converter, often different topologies techniques are involved. In this project a new topology is studied, cascading to half bridges, each working similar to a boost converter but with magnetic coupled inductors in-between.    The converter design is modeled in PLECS Blockset and MATLAB Simulink to simulate and evaluate the performance with proper design procedure. The results showed that a high step-up gain was achieved, and the gain could easily be adjusted by changing the duty cycle and/or the coupling factor. The converter design showed similarities and differences to a traditional boost converter. The coupled inductor has its advantage reducing the fuel cell current ripple with the effect of the duty cycle.

The present thesis deals with fault impact mitigation in grid connected converters used for High Voltage Direct Current transmission. Certain critical fault cases require additional obstructing protection actions to ease the impact on the converter valves. DC sided faults drives high fault currents through the converters. Single phase to ground faults at the converter AC bus results in overvoltages across the converter valve arms. The phenomenon of these faults are described both for symmetric and asymmetric configurations. Different available solutions are explained and evaluated. Simulations in PSCAD/EMTDC show the impact of the protection measures. A three phase short circuit introduced on the tertiary winding of the transformer is an effective temporary measure against the destructive fault cases. It is shown in this report that a tertiary shortcircuit will greatly reduce the overvoltages after converter bus faults and redirect a large part of the fault currents after DC faults. With the lower voltage on the tertiary winding, it is a suitable connection point for short circuit devices.

This thesis presents an active clamp forward converter for use in the Energy Harvesting From Exercise Machines project. Ideally, this converter will find use as the centerpiece in a process that links elliptical trainers to the California grid. This active clamp forward converter boasts a 14V-60V input voltage range and 150W power rating, which closely match the output voltage and power levels from the elliptical trainer. The isolated topology outputs 51V, higher than previous, non-isolated attempts, which allows the elliptical trainers to interact with a central grid-tied inverter instead of many small ones. The final converter operated at greater than 86% efficiency over most of the elliptical trainer’s input range, and produced very little noise, making it a solid choice for this implementation.