<p>The objective of this master thesis was to investigate the possibility to measure the gain in stiffness of the dry coating due to film formation of latex with a Dynamic Mechanic Thermal Analyzer (DMTA). This could tell when and to which extent the latex forms a film after the drying process.</p><p>Two latices with different Tg was used for the experiments, one with a Tg of 36°C, denoted hard, and the one with a Tg of 8°C, denoted soft. The hard latex was used to make coating samples that would not form a film when dried at room temperature and the soft latex was used as a reference to the coating with hard latex since it would form a film at room temperature.</p><p>It was shown that a gain in stiffness due to film formation of latex in coating can be measured with a DMTA. It was also shown that that the film forming of latex in coatings depend on time, temperature and the history of the sample. Further investigations were carried out to try to determine the time for film formation to be completed at a certain temperature.. These investigations showed that this type of trials cannot be carried out in a DMTA directly since the stiffness seemed to increase monotonically during a very ling time. This might be due to the rearrangements in the pigment structure that might affect the gain in stiffness. Therefore, a method involving oven curing was developed. Only one series of test were performed with this method due to lack of time but the method showed promising results.</p> / <p>Syftet med detta examensarbete var att undersöka möjligheten att använda en Dynamic Mechanic Thermal Analyzer (DMTA) för att mäta ökningen av styvhet som följd av filmbildning av latex i en torr bestrykning.</p><p>Två olika latexer användes för experimenten, en med Tg = 36°C (hård) och en med Tg = 8°C (mjuk). Den hårda latexen användes för att kunna göra tester på prover som ännu inte filmbildat när de torkat vid rumstemperatur och den mjuka latexen användes för att göra referens prover mot bestrykningen med hård latex.</p><p>Resultaten visade att det går att mäta styvhetsökning i bestrykningen som en följd av filmformation med DMTA och filmformation av latex i bestrykningen troligtvis beror på både tid, temperatur och provets historia. Ett försök att mäta vilken uppehålls tid vid en specifik temperatur som krävs för att filmbildningen skall fulländas genomfördes. Dessa försök visade att DMTA:n inte var en lämplig metod för att mäta denna tid då styvheten verkade öka under en längre tid. Detta kan bero på att pigment partiklarna packade sig tätare och på så sätt orsakade en ökning av styvheten. Därför gjordes ett annat försök som involverar ugns härdning, men på grund av tidsbrist blev det bara en mätserie utförd. Den sist nämnda metoden visade dock goda resultat och måste därför bedömas ha en potential.</p>

The objective of this master thesis was to investigate the possibility to measure the gain in stiffness of the dry coating due to film formation of latex with a Dynamic Mechanic Thermal Analyzer (DMTA). This could tell when and to which extent the latex forms a film after the drying process. Two latices with different Tg was used for the experiments, one with a Tg of 36°C, denoted hard, and the one with a Tg of 8°C, denoted soft. The hard latex was used to make coating samples that would not form a film when dried at room temperature and the soft latex was used as a reference to the coating with hard latex since it would form a film at room temperature. It was shown that a gain in stiffness due to film formation of latex in coating can be measured with a DMTA. It was also shown that that the film forming of latex in coatings depend on time, temperature and the history of the sample. Further investigations were carried out to try to determine the time for film formation to be completed at a certain temperature.. These investigations showed that this type of trials cannot be carried out in a DMTA directly since the stiffness seemed to increase monotonically during a very ling time. This might be due to the rearrangements in the pigment structure that might affect the gain in stiffness. Therefore, a method involving oven curing was developed. Only one series of test were performed with this method due to lack of time but the method showed promising results. / Syftet med detta examensarbete var att undersöka möjligheten att använda en Dynamic Mechanic Thermal Analyzer (DMTA) för att mäta ökningen av styvhet som följd av filmbildning av latex i en torr bestrykning. Två olika latexer användes för experimenten, en med Tg = 36°C (hård) och en med Tg = 8°C (mjuk). Den hårda latexen användes för att kunna göra tester på prover som ännu inte filmbildat när de torkat vid rumstemperatur och den mjuka latexen användes för att göra referens prover mot bestrykningen med hård latex. Resultaten visade att det går att mäta styvhetsökning i bestrykningen som en följd av filmformation med DMTA och filmformation av latex i bestrykningen troligtvis beror på både tid, temperatur och provets historia. Ett försök att mäta vilken uppehålls tid vid en specifik temperatur som krävs för att filmbildningen skall fulländas genomfördes. Dessa försök visade att DMTA:n inte var en lämplig metod för att mäta denna tid då styvheten verkade öka under en längre tid. Detta kan bero på att pigment partiklarna packade sig tätare och på så sätt orsakade en ökning av styvheten. Därför gjordes ett annat försök som involverar ugns härdning, men på grund av tidsbrist blev det bara en mätserie utförd. Den sist nämnda metoden visade dock goda resultat och måste därför bedömas ha en potential.

Les nanocomposites suscitent un intérêt croissant depuis leur développement dans les années 90 par Toyota. Par conséquent, l'amélioration des propriétés de ce type de matériaux est un enjeu fort tant d'un point de vue fondamental qu'industriel. Cette amélioration peut passer par un choix pertinent des charges renforçantes ajoutées à la matrice notamment en ce qui concerne le type, la géométrie, la proportion et le traitement de ces charges. L’optimisation des paramètres d’élaboration du mélange y joue aussi un rôle important. L’objectif de ce travail est de contribuer à l’identification et à la compréhension des mécanismes à l'origine du renforcement des matrices thermoplastiques par des nanocharges. Cet aspect est abordé à travers l’étude des propriétés thermiques et mécaniques des nanocomposites formés d’une matrice Polyamide 12 (PA12) chargées par des nanoparticules d’argile organiquement modifiée. Plus précisément, nous avons analysé les effets de la fraction massique des charges et du vieillissement naturel sur les propriétés structurales, thermiques et mécaniques de ces nanocomposites. L’influence des conditions de mélangeage sur ces propriétés ont aussi été examinées. Nous avons particulièrement mis l’accent sur l’identification des liens qui existent entre les propriétés macroscopiques et la structure des nanocomposites. Nous avons aussi fait une étude comparative des propriétés viscoélastiques de ces matériaux à l'état fondu et à l'état solide, ce qui représente une des originalités forte de ce travail. / Nanocomposites are interestingly growing since their development in the 1990s by Toyota Company. Therefore, improving the properties of such materials is a major issue from fundamental and industrial point of view. This improvement can pass through a relevant choice of reinforcing loads added to the matrix particularly regarding the type, geometry, the proportion, and the treatment of these fillers. The processing parameters of the mixture play also a key role. The objective of this work is to contribute to the identification and understanding of the mechanisms at the origin of the reinforcing thermoplastic matrices by nanofillers. This aspect presented through the study of the thermal and mechanical properties of nanocomposites formed by a polyamide 12 matrix (PA12) filled with organically modified clay nanoparticles. More specifically, we analysed the effects of the filler mass fraction and environmental aging on structural, thermal and mechanical properties of these nanocomposites. The mixing conditions on these properties were also examined. A particular attention has been paid to the study of relationships between the macroscopic properties and the structure of nanocomposites. Viscoelastic properties of these materials in both melt and solid states were compared, which represents one of the originalities of this work.

A transmissão de dados e informação na fibra óptica vem aumentando nos últimos anos. O interesse para avaliar melhor a confiabilidade mecânica tomou-se uma necessidade, depois que uma fibra, de um cabo instalado, estava se partindo com muita facilidade. O foco principal deste trabalho foi voltado para estabelecer metodologias para avaliar o estado de degradação dos polímeros usados. Através destas técnicas, buscou-se encontrar parâmetros (E\', E\", tan &#948, Tg, etc.) que pudessem indicar o estado de degradação dos revestimentos. Diferentes técnicas foram empregadas para avaliar o revestimento das fibras tais como: calorimetria exploratória diferencial (DSC), diferencial fotocalorimetria (DPC), análise térmica dinâmico mecânico (DMTA) e espectroscopia na região do infravermelho (FIIR). A partir da técnica desenvolvida, DMTA, esta pode ser empregada para avaliar a confiabilidade mecânica de várias fibras comercias. As técnicas DMTA e FIIR mostraram ser muito promissoras, pois consegue-se, através delas, obter muitos dados a respeito das características dos polímeros. / The datas and information transmission in the optical fiber have been increasing in the last years. The interest to evaluate the mechanical reliability became necessary, after that a optical fiber, from a cable installed, was cracking very easily. The principal aim of this work was establishing methodologies to evaluate the polymer degradation state. Through of this techniques we search to find out parameters (E\', E\", tan &#948, Tg. etc) that could denote the degradation state of the coatings. Different techniques were utilized to evaluate the coating of the optical fibers such as: differential scanning calorimeter (DSC), differential photocalorimeter (DPC), dynamic mechanic thermal analyzer (DMTA) and infrared spectroscopy (FIIR). From the method development (DMTA), it was possible to evaluate the mechanical realiability of many commercial fibers. DMTA and FTIR techniques shown to be very promising to obtain very dates to respect of polymer characteristics.

Made available in DSpace on 2016-06-02T19:12:04Z (GMT). No. of bitstreams: 1 3292.pdf: 2469537 bytes, checksum: cab8a8d13a7ab1753c5b3bbfe24b647a (MD5) Previous issue date: 2010-08-11 / The growing advanced composites appliance in aircraft s structural parts has demanded to spread the knowledge about mechanical behavior prediction in longer time periods. In this way, the main purpose of this study is to establish an accelerated test method based on mechanical-dynamical-thermal analysis (DMTA), to predict the mechanical behavior of carbon fiber/epoxy resin composites. The DMTA technique was used on two modes: multi-frequency and creep. In the first case, three point bending tests on dynamical mode did not present a good fitting to built master curves, considering the experimental parameters used. Though, creep tests showed good results. In these tests, parameters used as temperature range from 25ºC to 235ºC and isothermals at every 15ºC for 100 minutes allowed to obtain compliance modulus versus time master curves with a good fitting. From the obtained results, it is possible to conclude that the proposed method presented good adhesion to the basic concept of material viscoelasticity, therefore can be used to predict mechanical behavior of composite materials. / A crescente demanda de uso de compósitos poliméricos avançados em peças de responsabilidade estrutural na indústria aeronáutica tem exigido ampliar o conhecimento sobre a predição do comportamento mecânico desses materiais em longos períodos de tempo. Nesse sentido, este trabalho tem como objetivo estabelecer uma metodologia de ensaios acelerados, utilizando a técnica de análise térmica dinâmico-mecânica (DMTA), para prever o comportamento mecânico de compósitos de fibras de carbono em matriz de resina epóxi. O uso da técnica de DMTA foi baseado em dois tipos de ensaios: multifrequências e fluência. No primeiro caso, ensaios de flexão três pontos, em modo dinâmico, não mostraram bom ajuste na construção de curvas mestre, dentro das condições usadas neste estudo. Já ensaios realizados no modo de fluência apresentaram resultados promissores. Neste tipo de ensaio, o uso dos parâmetros, como intervalo de temperaturas de 25ºC a 235ºC e isotermas a cada 15ºC, com 100 minutos de duração, possibilitaram a construção de curvas mestre do módulo de compliância em função do tempo com um bom ajuste. A partir dos resultados obtidos pode-se concluir que o método proposto apresenta adesão aos conceitos básicos de viscoelasticidade de materiais e, portanto, pode ser utilizado para previsão do comportamento de materiais compósitos em longos períodos de tempo. A crescente demanda de uso de compósitos poliméricos avançados em peças de responsabilidade estrutural na indústria aeronáutica tem exigido ampliar o conhecimento sobre a predição do comportamento mecânico desses materiais em longos períodos de tempo. Nesse sentido, este trabalho tem como objetivo estabelecer uma metodologia de ensaios acelerados, utilizando a técnica de análise térmica dinâmico-mecânica (DMTA), para prever o comportamento mecânico de compósitos de fibras de carbono em matriz de resina epóxi. O uso da técnica de DMTA foi baseado em dois tipos de ensaios: multifrequências e fluência. No primeiro caso, ensaios de flexão três pontos, em modo dinâmico, não mostraram bom ajuste na construção de curvas mestre, dentro das condições usadas neste estudo. Já ensaios realizados no modo de fluência apresentaram resultados promissores. Neste tipo de ensaio, o uso dos parâmetros, como intervalo de temperaturas de 25ºC a 235ºC e isotermas a cada 15ºC, com 100 minutos de duração, possibilitaram a construção de curvas mestre do módulo de compliância em função do tempo com um bom ajuste. A partir dos resultados obtidos pode-se concluir que o método proposto apresenta adesão aos conceitos básicos de viscoelasticidade de materiais e, portanto, pode ser utilizado para previsão do comportamento de materiais compósitos em longos períodos de tempo.

A transmissão de dados e informação na fibra óptica vem aumentando nos últimos anos. O interesse para avaliar melhor a confiabilidade mecânica tomou-se uma necessidade, depois que uma fibra, de um cabo instalado, estava se partindo com muita facilidade. O foco principal deste trabalho foi voltado para estabelecer metodologias para avaliar o estado de degradação dos polímeros usados. Através destas técnicas, buscou-se encontrar parâmetros (E\', E\", tan &#948, Tg, etc.) que pudessem indicar o estado de degradação dos revestimentos. Diferentes técnicas foram empregadas para avaliar o revestimento das fibras tais como: calorimetria exploratória diferencial (DSC), diferencial fotocalorimetria (DPC), análise térmica dinâmico mecânico (DMTA) e espectroscopia na região do infravermelho (FIIR). A partir da técnica desenvolvida, DMTA, esta pode ser empregada para avaliar a confiabilidade mecânica de várias fibras comercias. As técnicas DMTA e FIIR mostraram ser muito promissoras, pois consegue-se, através delas, obter muitos dados a respeito das características dos polímeros. / The datas and information transmission in the optical fiber have been increasing in the last years. The interest to evaluate the mechanical reliability became necessary, after that a optical fiber, from a cable installed, was cracking very easily. The principal aim of this work was establishing methodologies to evaluate the polymer degradation state. Through of this techniques we search to find out parameters (E\', E\", tan &#948, Tg. etc) that could denote the degradation state of the coatings. Different techniques were utilized to evaluate the coating of the optical fibers such as: differential scanning calorimeter (DSC), differential photocalorimeter (DPC), dynamic mechanic thermal analyzer (DMTA) and infrared spectroscopy (FIIR). From the method development (DMTA), it was possible to evaluate the mechanical realiability of many commercial fibers. DMTA and FTIR techniques shown to be very promising to obtain very dates to respect of polymer characteristics.

Cette thèse s'articule autour de la caractérisation des propriétés thermophysiques et mécaniques d'un produit modèle : la Tylose et d'un produit alimentaire: le chocolat, ainsi qu'une modélisation du couplage thermique-mécanique en cours de congélation. L'étude expérimentale (en statique et en dynamique) a mis en évidence l'influence de la formation de glace sur la variation des propriétés mécaniques en fonction de la température. L'étude numérique a été réalisée sur une géométrie simple (plaque de Tylose) et sur deux géométries bicouches (plaque et cylindre), en éléments finis. Les simulations ont mis en évidence une contrainte parallèle au flux thermique qui engendre au sein de la structure une compression (proche de la température de cristallisation) suivi d'une tension (après l'apparition de 90% de glace). Cette contrainte complexe pourra engendrer l'apparition de fissures au sein du produit. De plus, le champ de déformation globale peut être utilisé comme un nouveau paramètre de contrôle et d'optimisation de la congélation. La présence de fortes contraintes aux interfaces peut également engendrer la création de fissures.

This work deals with the measurement of electrical conductivity and mechanical properties of gel polymer electrolyte containing Lithium ion and their preparation. The theoretical part deals with the development of gel polymer electrolyte, their use and methods of measurement of electrical conductivity and mechanical properties. In the experimental part describes the preparation of gel electrolyte, the measurement of electrical conductivity, temperature dependence and the measurement of mechanical properties.

Le refroidissement global et les oscillations entre cycles glaciaires et interglaciaires du Pléistocène inférieur ont pour conséquence une alternance entre milieux steppiques et forestiers, favorisant par là-même renouvellements et dispersions fauniques dont celui du genre Homo.Dans les interprétations paléoenvironnementales basées sur les assemblages fauniques, les cervidés, parmi les plus abondants mammifères, sont classiquement considérés comme forestiers, mais ce paradigme ne reflète pas la complexité de la diversité écologique réelle des cervidés.L'analyse texturale de 921 spécimens représentant les 5 cervidés actuels à l'écologie référencée a permis d'établir une robuste base de données et d'attester du lien significatif entre micro-usure dentaire et ressources végétales. L'analyse de 547 cervidés fossiles issus de 15 localités européennes souligne leur grande diversité écologique. Eucladoceros ctenoides et Metacervoceros rhenanus présentent une alimentation plastique. Leur analyse permet l'identification de réponses alimentaires adaptatives aux modifications environnementales liées aux oscillations climatiques. Ces deux cervidés, eurytopiques, constituent des indicateurs écologiques incontournables. La composante forestière supportée par la présence des cervidés est ici remise en cause ; les cervidés étant plus diversifiés écologiquement. L'analyse de la texture de la micro-usure dentaire des cervidés présents dans des sites européens, où la présence du genre Homo a été avancée, vise à identifier le type potentiel d'habitat favorable à sa dispersion en Eurasie. / The early Pleistocene is a period of global cooling and climatic oscillations punctuated by glacial and interglacial cycles. This period of climatic instability leads to an alternation of steppe and forest habitats resulting in faunal renewals and dispersals, including Homo dispersal.In paleoenvironmental reconstructions based on faunal assemblages, deer, which are among the most abundant mammals, are traditionally considered forest dwellers. However, this paradigm is far from reflecting the real complexity of deer ecological diversity.Via the textural analysis of 921 representatives of the 5 extant European deer with known ecology, a solid reference database has been setup. It attests of the significative link existing between dental micro-wear and vegetal resources. The analysis of 547 fossils from 15 European localities underlines the ecological diversity among fossil deer. Eucladoceros ctenoides and Metacervoceros rhenanus are plastic in their diet. The analysis of such deer allows the identification of dietary adaptive answers to environmental modifications resulting from climatic oscillations. Being eurytopic, they constitute essential proxies for paleoenvironmental reconstructions. The results challenge the link existing between the occurrence of deer and the presence of forest habitats, as deer are ecologically more diversified.The textural analysis of deer from European human bearing localities aims at characterizing potential habitats favorable toward Homo dispersion in Eurasia.

The aim of this research was to analyze the mechanical and thermal properties of composites andhybrid composites prepared with four types of jute fibers and two different resins; biobased thermosetresins acrylated epoxidized soybean oil (AESO) and mathacrylated anhydride modified soybean oil(MMSO). The processing technique used was vacuum injection molding (VIM). Tensile and, flexuraltestings and dynamic mechanical and thermal analysis (DMTA) were used to characterize thecomposites’ properties. The results showed that the AESO composites have better tensile and flexuralproperties. This may be due to the fact that the curing conditions were quite the same for both AESOand MMSO composites but MMSO composites showed different behavior during curing step. Theywere completely cured in a shorter time compared to AESO composites. Having equal curing time forboth resins’ composites can damage the structure of MMSO composites and hybrids. Tan delta peak forthe MMSO reinforced composites occurs at higher temperatures, compared to AESO reinforcedcomposites, which means better thermal properties for MMSO reinforced composites.