Fluidized bed dryers are used in the pharmaceutical industry for the batch drying of pharmaceutical granulate. Maintaining optimal hydrodynamic conditions throughout the drying process is essential to product quality. Due to the complex interactions inherent in the fluidized bed drying process, mechanistic models capable of identifying these optimal modes of operation are either unavailable or limited in their capabilities. Therefore, empirical models based on experimentally generated data are relied upon to study these systems.<p> Principal Component Analysis (PCA) and Partial Least Squares (PLS) are multivariate statistical techniques that project data onto linear subspaces that are the most descriptive of variance in a dataset. By modeling data in terms of these subspaces, a more parsimonious representation of the system is possible. In this study, PCA and PLS are applied to data collected from a fluidized bed dryer containing pharmaceutical granulate. <p>System hydrodynamics were quantified in the models using high frequency pressure fluctuation measurements. These pressure fluctuations have previously been identified as a characteristic variable of hydrodynamics in fluidized bed systems. As such, contributions from the macroscale, mesoscale, and microscales of motion are encoded into the signals. A multiresolutional decomposition using a discrete wavelet transformation was used to resolve these signals into components more representative of these individual scales before modeling the data. <p>The combination of multiresolutional analysis with PCA and PLS was shown to be an effective approach for modeling the conditions in the fluidized bed dryer. In this study, datasets from both steady state and transient operation of the dryer were analyzed. The steady state dataset contained measurements made on a bed of dry granulate and the transient dataset consisted of measurements taken during the batch drying of granulate from approximately 33 wt.% moisture to 5 wt.%. Correlations involving several scales of motion were identified in both studies.<p> In the steady state study, deterministic behavior related to superficial velocity, pressure sensor position, and granulate particle size distribution was observed in PCA model parameters. It was determined that these properties could be characterized solely with the use of the high frequency pressure fluctuation data. Macroscopic hydrodynamic characteristics such as bubbling frequency and fluidization regime were identified in the low frequency components of the pressure signals and the particle scale interactions of the microscale were shown to be correlated to the highest frequency signal components. PLS models were able to characterize the effects of superficial velocity, pressure sensor position, and granulate particle size distribution in terms of the pressure signal components. Additionally, it was determined that statistical process control charts capable of monitoring the fluid bed hydrodynamics could be constructed using PCA<p>In the transient drying experiments, deterministic behaviors related to inlet air temperature, pressure sensor position, and initial bed mass were observed in PCA and PLS model parameters. The lowest frequency component of the pressure signal was found to be correlated to the overall temperature effects during the drying cycle. As in the steady state study, bubbling behavior was also observed in the low frequency components of the pressure signal. PLS was used to construct an inferential model of granulate moisture content. The model was found to be capable of predicting the moisture throughout the drying cycle. Preliminary statistical process control models were constructed to monitor the fluid bed hydrodynamics throughout the drying process. These models show promise but will require further investigation to better determine sensitivity to process upsets.<p> In addition to PCA and PLS analyses, Multiway Principal Component Analysis (MPCA) was used to model the drying process. Several key states related to the mass transfer of moisture and changes in temperature throughout the drying cycle were identified in the MPCA model parameters. It was determined that the mass transfer of moisture throughout the drying process affects all scales of motion and overshadows other hydrodynamic behaviors found in the pressure signals.

Cette thèse s'inscrit dans la recherche d'images basée sur leur contenu. La recherche opère sur des images eprésentéesdans un domaine transformé et où sont construits directement les vecteurs de caractéristiques ou indices. Deux types detransformations sont explorés : la transformée en cosinus discrète ou Discrete Cosine Transform (DCT) et la transforméen ondelettes discrète ou Discrete Wavelet Transform (DWT), utilisés dans les normes de compression JPEG et JPEG2000. Basés sur les propriétés des coefficients de la transformation, différents vecteurs de caractéristiquessont proposés. Ces vecteurs sont mis en oeuvre dans la reconnaissance de visages et de textures couleur.Dans le domaine DCT, sont proposés quatre types de vecteurs de caractéristiques dénommés "patterns" : Zigzag-Pattern,Sum-Pattern, Texture-Pattern et Color-Pattern. Le premier type est l'amélioration d'une approche existante. Les trois derniers intègrent la capacité de compactage des coefficients DCT, sachant que certains coefficients représentent une information de directionnalité. L'histogramme de ces vecteurs est retenu comme descripteur de l'image. Pour une réduction de la dimension du descripteur lors de la construction de l'histogramme il est défini, soit une adjacence sur des patterns proches puis leur fusion, soit une sélection des patterns les plus fréquents. Ces approches sont évaluées sur des bases de données d'images de visages ou de textures couramment utilisées. Dans le domaine DWT, deux types d'approches sont proposés. Dans le premier, un vecteur-couleur et un vecteur-texture multirésolution sont élaborés. Cette approche se classe dans le cadre d'une caractérisation séparée de la couleur et de la texture. La seconde approche se situe dans le contexte d'une caractérisation conjointe de la couleur et de la texture. Comme précédemment, l'histogramme des vecteurs est choisi comme descripteur en utilisant l'algorithme K-means pour construire l'histogramme à partir de deux méthodes. La première est le procédé classique de regroupement des vecteurs par partition. La seconde est un histogramme basé sur une représentation parcimonieuse dans laquelle la valeur des bins représente le poids total des vecteurs de base de la représentation.

No description available.

No description available.

This Master thesis is focused on the analysis of currently used methods which whose target is to determine the rate of image focus. This analysis was used during the development of the program which evaluates the rate of image focus in percentage rate, works in real time and cooperates with a camera capable of 4k image resolution with a manual focus of the lenses. Application is then capable of a finding of a pre-defined image under certain circumstances which is being used for increasing of effectivity of image focusing. Another option is represented by a method that is searching the most suitable area for focusing in the center of the image. A detailed description of these methods and program itself are also included in the thesis. The final part of the thesis contains records of measurement tests with its results.

yes / PICARD is a space-based observatory hosting the Solar Diameter Imager and Surface Mapper (SODISM) telescope, which has continuously observed the Sun from July 2010 and up to March 2014. In order to study the fine structure of the solar surface, it is helpful to apply techniques that enhance the images so as to improve the visibility of solar features such as sunspots or faculae. The objective of this work is to develop an innovative technique to enhance the quality of the SODISM images in the five wavelengths monitored by the telescope at 215.0 nm, 393.37 nm, 535.7 nm, 607.1 nm and 782.2 nm. An enhancement technique using interpolation of the high-frequency sub-bands obtained by Discrete Wavelet Transforms (DWT) and the input image is applied to the SODISM images. The input images are decomposed by the DWT as well as Stationary Wavelet Transform (SWT) into four separate sub-bands in horizontal and vertical directions namely, low-low (LL), low-high (LH), high-low (HL) and high–high (HH) frequencies. The DWT high frequency sub-bands are interpolated by a factor 2. The estimated high frequency sub-bands (edges) are enhanced by introducing an intermediate stage using a stationary Wavelet Transform (SWT), and then all these sub-bands and input image are combined and interpolated with half of the interpolation factor α/2, used to interpolate the high-frequency sub-bands, in order to reach the required size for IDWT processing. Quantitative and visual results show the superiority of the proposed technique over a bicubic image resolution enhancement technique. In addition, filling factors for sunspots are calculated from SODISM images and results are presented in this work.

No / Study is presented into the performance of Fast Fourier Transform (FFT) and Discrete Wavelet Transform (DWT) and MIMO-DWT with transmit beamforming. Feedback loop has been used between the equalizer at the transmitter to the receiver which provided the channel state information which was then used to construct a steering matrix for the transmission sequence such that the received signals at the transmitter can be combined constructively in order to provide a reliable and improved system for next generation wireless systems. As convolution in time domain equals multiplication in frequency domain no such counterpart exist for the symbols in space, means linear convolution and Intersymbol Interference (ISI) generation so both zero forcing (ZF) and minimum mean squared error (MMSE) equalizations have been employed. The results show superior performance improvement and in addition allow keeping the processing, power and implementation cost at the transmitter which has less constraints and the results also show that both equalization algorithms perform alike in wavelets and the ISI is spread equally between different wavelet domains.

The task of detecting human faces within either a still image or a video frame is one of the most popular object detection problems. For the last twenty years researchers have shown great interest in this problem because it is an essential pre-processing stage for computing systems that process human faces as input data. Example applications include face recognition systems, vision systems for autonomous robots, human computer interaction systems (HCI), surveillance systems, biometric based authentication systems, video transmission and video compression systems, and content based image retrieval systems. In this thesis, non-traditional methods are investigated for detecting human faces within color images or video frames. The attempted methods are chosen such that the required computing power and memory consumption are adequate for real-time hardware implementation. First, a standard color image database is introduced in order to accomplish fair evaluation and benchmarking of face detection and skin segmentation approaches. Next, a new pre-processing scheme based on skin segmentation is presented to prepare the input image for feature extraction. The presented pre-processing scheme requires relatively low computing power and memory needs. Then, several feature extraction techniques are evaluated. This thesis introduces feature extraction based on Two Dimensional Discrete Cosine Transform (2D-DCT), Two Dimensional Discrete Wavelet Transform (2D-DWT), geometrical moment invariants, and edge detection. It also attempts to construct a hybrid feature vector by the fusion between 2D-DCT coefficients and edge information, as well as the fusion between 2D-DWT coefficients and geometrical moments. A self organizing map (SOM) based classifier is used within all the experiments to distinguish between facial and non-facial samples. Two strategies are tried to make the final decision from the output of a single SOM or multiple SOM. Finally, an FPGA based framework that implements the presented techniques, is presented as well as a partial implementation. Every presented technique has been evaluated consistently using the same dataset. The experiments show very promising results. The highest detection rate of 89.2% was obtained when using a fusion between DCT coefficients and edge information to construct the feature vector. A second highest rate of 88.7% was achieved by using a fusion between DWT coefficients and geometrical moments. Finally, a third highest rate of 85.2% was obtained by calculating the moments of edges. / Master of Science

This thesis examines three decomposition techniques and their usability for economic and financial time series. The stock index DAX30 and the exchange rate from British pound to US dollar are used as representative economic time series. Additionally, autoregressive and conditional heteroscedastic simulations are analysed as benchmark processes to the real data. Discrete wavelet transform (DWT) uses wavelike functions to adapt the behaviour of time series on different time scales. The second method is the singular spectral analysis (SSA), which is applied to extract influential reconstructed modes. As a third algorithm, empirical mode decomposition (END) leads to intrinsic mode functions, who reflect the short and long term fluctuations of the time series. Some problems arise in the decomposition process, such as bleeding at the DWT method or mode mixing of multiple EMD mode functions. Conclusions to evaluate the predictability of the time series are drawn based on entropy - and recurrence - analysis. The cyclic behaviour of the decompositions is examined via the coefficient of variation, based on the instantaneous frequency. The results show rising predictability, especially on higher decomposition levels. The instantaneous frequency measure leads to low values for regular oscillatory cycles, irregular behaviour results in a high variation coefficient. The singular spectral analysis show frequency - stable cycles in the reconstructed modes, but represents the influences of the original time series worse than the other two methods, which show on the contrary very little frequency - stability in the extracted details.

This thesis focuses on image processing using wavelet transform. The usage of wavelet transform is analysed especially for image compression and image noise reduction purposes. The analysis describes in detail aspects and application of the following wavelet transform methods: CWT, DWT, DTWT, 2D DWT. The thesis further explains the meaning of the mother wavelet and studies certain specific kinds of wavelets, kinds of thresholding and its purposes and also touches on the JPEG2000 standard. Mathematica and Sage software packages were used to design algorithms for image compression and image noise reduction, utilising relevant wavelet transform findings. The concluding part of the thesis compares the two software packages and results obtained using different algorithms.