Conventional multicell wireless systems operate with out-of-cell interference treated as background noise; consequently, their performance faces two major limitations: 1)Signal processing is performed on a per-cell basis; and 2)Intercell interference detection is infeasible as intercell interference, although significantly above the noise level, is typically quite weak. In this thesis, we consider a multicell downlink scenario, where base-stations are equipped with multiple transmit antennas, the remote users are equipped with a single antenna, and multiple remote users are active simultaneously via spatial division multiplexing. We propose solutions for the above limitations by considering techniques for mitigating interference. The first part of the thesis proposes solutions for the first limitation. It considers the benefit of coordinating base-stations across multiple cells, where multiple base-stations may jointly optimize their respective beamformers to improve the overall system performance. It focuses on the design criteria of minimizing either the total weighted transmitted power or the maximum per-antenna power across the base-stations subject to signal-to-interference-and-noise-ratio (SINR) constraints at the remote users. The main contribution of this part is an efficient algorithm for finding the joint globally optimal beamformers across all base-stations. The proposed algorithm is based on a generalization of uplink-downlink duality to the multicell setting using the Lagrangian duality theory. An important feature is that it naturally leads to a distributed implementation in time-division duplex (TDD) systems. Simulation results suggest that coordinating the beamforming vectors alone already provides appreciable performance improvements as compared to the conventional per-cell optimized network. The second part of the thesis considers the transmission of both private and common messages for the sole purpose of intercell interference mitigation. It solves the issues of the second limitation mentioned above. It considers the benefit of designing decodable interference signals by allowing common-private message splitting at the transmitter and common message decoding by users in adjacent cells. It solves a network optimization problem of jointly determining the appropriate users in adjacent cells for rate splitting, the optimal beamforming vectors for both common and private messages, and the optimal common-private rates to minimize the total transmit power across the base-stations subject to service rate requirements for remote users. Observe that for fixed user selection and fixed common-private rate splitting, the optimization of beamforming vectors can be performed using a semidefinite programming approach. Further, this part of the thesis proposes a heuristic user-selection and rate splitting strategy to maximize the benefit of common message decoding. This part proposes a heuristic algorithm to characterize the improvement in the feasible rates with common-message decoding. Simulation results show that common message decoding can significantly improve both the total transmit power and the feasibility region for cell-edge users when base-stations are closely spaced from each other.

Conventional multicell wireless systems operate with out-of-cell interference treated as background noise; consequently, their performance faces two major limitations: 1)Signal processing is performed on a per-cell basis; and 2)Intercell interference detection is infeasible as intercell interference, although significantly above the noise level, is typically quite weak. In this thesis, we consider a multicell downlink scenario, where base-stations are equipped with multiple transmit antennas, the remote users are equipped with a single antenna, and multiple remote users are active simultaneously via spatial division multiplexing. We propose solutions for the above limitations by considering techniques for mitigating interference. The first part of the thesis proposes solutions for the first limitation. It considers the benefit of coordinating base-stations across multiple cells, where multiple base-stations may jointly optimize their respective beamformers to improve the overall system performance. It focuses on the design criteria of minimizing either the total weighted transmitted power or the maximum per-antenna power across the base-stations subject to signal-to-interference-and-noise-ratio (SINR) constraints at the remote users. The main contribution of this part is an efficient algorithm for finding the joint globally optimal beamformers across all base-stations. The proposed algorithm is based on a generalization of uplink-downlink duality to the multicell setting using the Lagrangian duality theory. An important feature is that it naturally leads to a distributed implementation in time-division duplex (TDD) systems. Simulation results suggest that coordinating the beamforming vectors alone already provides appreciable performance improvements as compared to the conventional per-cell optimized network. The second part of the thesis considers the transmission of both private and common messages for the sole purpose of intercell interference mitigation. It solves the issues of the second limitation mentioned above. It considers the benefit of designing decodable interference signals by allowing common-private message splitting at the transmitter and common message decoding by users in adjacent cells. It solves a network optimization problem of jointly determining the appropriate users in adjacent cells for rate splitting, the optimal beamforming vectors for both common and private messages, and the optimal common-private rates to minimize the total transmit power across the base-stations subject to service rate requirements for remote users. Observe that for fixed user selection and fixed common-private rate splitting, the optimization of beamforming vectors can be performed using a semidefinite programming approach. Further, this part of the thesis proposes a heuristic user-selection and rate splitting strategy to maximize the benefit of common message decoding. This part proposes a heuristic algorithm to characterize the improvement in the feasible rates with common-message decoding. Simulation results show that common message decoding can significantly improve both the total transmit power and the feasibility region for cell-edge users when base-stations are closely spaced from each other.

In this thesis, multiuser receivers for code division multiple-access (CDMA) downlink are studied under frequency selective fading channel conditions. The receivers investigated in this thesis attempt to estimate desired symbol as a linear combination of chip-rate sampled received signal sequence. A common matrix-vector representation of signals, which is similar to the model given by Paulraj et. al. is constructed in order to analyze the receivers studied in this thesis. Two receivers already well known in the literature are introduced and derived by using the common signal model. One of the receivers uses traditional matched filter and the other uses symbol-level linear minimum mean square error (MMSE) estimation. The receiver that uses traditional matched filter, also known as the conventional RAKE receiver, benefits from time diversity by combining the signal energy from multiple paths. The conventional RAKE receiver is optimal when multiple-access interference (MAI) is absent. Linear MMSE based receivers are known to suppress MAI and to be more robust to noise enhancement. The optimal symbol-level linear MMSE based receiver requires inversion of large matrices whose size is determined by either number of active users or spreading factor. These two parameters can be quite large in many practical systems and hence the computational load of this receiver can be a problem. In this thesis, two alternative low-complexity receivers, which are chip-level linear MMSE equalizer proposed by Krauss et. al. and interference-suppressing RAKE receiver proposed by Paulraj et. al., are compared with the linear full-rank MMSE based receiver and with the conventional RAKE receiver in terms of bit-error-rate performance. Various simulations are performed to evaluate the performance of the receivers and the parameters affecting the receiver performance are investigated.

The increasing complexity of heterogeneous cellular networks (HetNets) due to the irregular deployment of small cells demands significant rethinking in the way cellular networks are perceived, modeled and analyzed. In addition to threatening the relevance of classical models, this new network paradigm also raises questions regarding the feasibility of state-of-the-art simulation-based approach for system design. This dissertation proposes a fundamentally new approach based on random spatial models that is not only tractable but also captures current deployment trends fairly accurately. First, this dissertation presents a general baseline model for HetNets consisting of K different types of base stations (BSs) that may differ in terms of transmit power, deployment density and target rate. Modeling the locations of each class of BSs as an independent Poisson Point Process (PPP) allows the derivation of surprisingly simple expressions for coverage probability and average rate. One interpretation of these results is that adding more BSs or tiers does not necessarily change the coverage probability, which indicates that fears of "interference overload" in HetNets are probably overblown. Second, a flexible notion of BS load is incorporated by introducing a new idea of conditionally thinning the interference field. For this generalized model, the coverage probability is shown to increase when lightly loaded small cells are added to the existing macrocellular networks. This is due to the fact that owing to the smaller loads, small cells typically transmit less often than macrocells, thus contributing less to the interference power. The same idea of conditional thinning is also shown to be useful in modeling the non-uniform user distributions, especially when the users lie closer to the BSs. Third, the baseline model is extended to study multi-antenna HetNets, where BSs across tiers may additionally differ in terms of the number of transmit antennas, number of users served and the multi-antenna transmission strategy. Using novel tools from stochastic orders, a tractable framework is developed to compare the performance of various multi-antenna transmission strategies for a fairly general spatial model, where the BSs may follow any general stationary distribution. The analysis shows that for a given total number of transmit antennas in the network, it is preferable to spread them across many single-antenna BSs vs. fewer multi-antenna BSs. Fourth, accounting for the load on the serving BS, downlink rate distribution is derived for a generalized cell selection model, where shadowing, following any general distribution, impacts cell selection while fading does not. This generalizes the baseline model and all its extensions, which either ignore the impact of channel randomness on cell selection or lumps all the sources of randomness into a single random variable. As an application of these results, it is shown that in certain regimes, shadowing naturally balances load across various tiers and hence reduces the need for artificial cell selection bias. Fifth and last, a slightly futuristic scenario of self-powered HetNets is considered, where each BS is powered solely by a self-contained energy harvesting module that may differ across tiers in terms of the energy harvesting rate and energy storage capacity. Since a BS may not always have sufficient energy, it may not always be available to serve users. This leads to a notion of availability region, which characterizes the fraction of time each type of BS can be made available under variety of strategies. One interpretation of this result is that the self-powered BSs do not suffer performance degradation due to the unreliability associated with energy harvesting if the availability vector corresponding to the optimal system performance lies in the availability region. / text

Research Doctorate - Doctor of Philosophy (PhD) / The Radio Access Network (RAN) accounts for the major proportion of the UMTS system operating cost. Transmission from radio base station sites contributes a larger part of the RAN operating costs. Selection of suitable transport technologies and proper allocation of network resources are vital from an operator cost optimisation and the Quality of Experience (QoE) points of view. This thesis extensively investigated the performance of a RAN to support multimedia traffic on a HSDPA air interface. Transport network layer of a future RAN could be based on a number of transport protocols such as ATM, IP and Ethernet. With the increasing traffic volume and diversity the efficiencies of IP and Ethernet based RAN could increases significantly due to the use of larger payloads and simpler resource allocation techniques. Also, on IP and Ethernet based links relatively fewer overhead bits are transmitted compared to an ATM based link. Both the IP and Ethernet based links appear to perform better under heavy traffic load conditions. An IP based link could perform better than an Ethernet based link when an IP header compression technique is used. An Ethernet based link is an alternative transport technique for the UTRAN transport network due to its flexibility, economy and bandwidth efficiency. The HSDPA (High Speed Downlink Packet Access) is considered to be one of the initial evolutionary steps to enhance the data rate, and QoS of downlink data and multimedia services for the evolved UMTS network. It can provide high data rate up to 28.8 Mbps on the downlink shared channel using the packet access technique. A HSDPA network can dynamically adjust a connection data rate to match radio conditions to ensure the highest possible data rate for different type of traffic. Inappropriate RAN capacity allocation could lead to low radio resource or RAN resource utilizations. In this thesis, a Markov chain based analytical model has been developed to study the interaction between the air interface and the RAN for a HSDPA network. The analytical model was used to study interactions of RAN transport protocols, flow control techniques and the air interface transmission conditions. Further a simulation model was developed to investigate the relationship between the HSDPA air interface and its RAN parameters. Another important issue in the HSDPA network design is the scheduling algorithm used at the Node-B. A scheduling algorithm plays a key role in allocating a RAN’s network resources. Impacts of scheduling algorithms are studied in this work using a simulation model. Based on the study of the HSDPA air interface and its RAN parameter interactions this work has developed an adaptive resource management algorithm, which uses the measured air interface information to allocate the corresponding connection data rate on the Iub link. The developed algorithm reduces RAN resource requirements while increasing the air interface resource utilization and QoS of connections.

This thesis describes GSM communication, the method of its jamming and design of a jammer for this band. This document is mainly focused on design of the jammer with the variable bandwidth of jamming and the variable level of output power. Requested parameters of jamming are set by a control panel with a LCD display. In this document there is a detailed description of each function block and connection between them. At the end of this thesis there are released measured results of designed jammer.

With increasing technological advancements more sophisticated mobile devices are being used by end-users. Third generation (3G) mobile communication systems such as Universal Mobile Telecommunication System (UMTS) are not able to satisfy the rising demand for higher throughputs and low latencies. New standards based on Orthogonal Frequency Division Multiplexing (OFDM), such as Long Term Evolution (LTE) and Worldwide Interoperability for Microwave Access (WiMAX), have been proposed and are currently being integrated into existing mobile networks all over the world. LTE specifications are being finalized within the 3rd Generation Partnership Project (3GPP) with the ambitious goals of increased spectral efficiency and end user throughput. Despite the introduction of several high data rate services, voice communication is still an essential part of the overall wireless wide area cellular communication market. In LTE, the core network is purely packet switched, thus voice is transmitted entirely using a Voice over Internet Protocol (VoIP). Like its predecessor standards it is desired that a large number of simultaneous VoIP calls be supported in LTE, while satisfying the desired Quality of Service (QoS) demands. This thesis examines issues related to VoIP capacity for LTE. One of the key challenges is the limited number of schedulable voice packets per sub frame. The main goal of this thesis is to quantify the impact of this limitation. After describing basic LTE concepts, a detailed description of the control channel resource limitations for the scheduling of voice packets is presented. Consequences of these limitations are explained systematically by presenting the problem in a wider context. Simulation results were obtained using the openWNS Simulator, an event driven system level simulation platform developed at the Communication Networks Research Group (ComNets), RWTH Aachen University Germany. Results are presented showing the impact of different scheduling strategies on VoIP capacity. These results illustrate how the limited control channel resources, specifically the Physical Downlink Control Channel (PDCCH) resources, affect the total number of schedulable VoIP user audio media streams. / Med ökande tekniska framsteg mer avancerade mobila enheter som används av slutanv ändarna. Tredje generationens (3G) mobila kommunikationssystem såsom Universal Mobile Telecommunication System (UMTS) inte kan tillgodose den ökande efterfrågan på högre genomströmning och låga latenser. Nya standarder som bygger på Orthogonal Frequency Division Multiplexing (OFDM), såsom Long Term Evolution (LTE) och Worldwide Interoperability för Microwave Access (WiMAX), har föreslagits och håller på att integreras I befintliga mobilnät över hela världen. LTE specifikationer håller på att färdigställas inom 3rd Generation Partnership Project (3GPP) med de ambitiösa målen om ökad spektral effektivitet och slutanvändare genomstr ömning. Trots införandet av flera tjänster av hög datahastighet, är röstkommunikation fortfarande en väsentlig del av den totala Wireless Wide Area cellulär kommunikation marknaden. I LTE är kärnnätet rent paketförmedlande därmed röst överförs helt och hållet med hjälp av en Voice over Internet Protocol (VoIP). Precis som sina föregångare standarder är det önskvärt att ett stort antal samtidiga VoIP samtal få stöd i LTE, samtidigt som det uppfyller önskade Quality of Service (QoS) krav. Denna avhandling undersöker frågor relaterade till VoIP kapacitet för LTE. En av de viktigaste utmaningarna är det begränsade antalet schemaläggningsbart röst paket per sub ram. Det huvudsakliga målet med denna avhandling är att kvantifiera effekterna av denna begränsning. Efter att ha beskrivit de grundläggande LTE begrepp, är en detaljerad beskrivning av de resurser kontroll kanal begränsningar för schemaläggning av röst paket presenteras. Konsekvenser av dessa begränsningar förklaras systematiskt genom att presentera problemet i ett större sammanhang. Simulering resultat erhölls med hjälp av openWNS Simulator, en händelse driven systemnivå simulering som utvecklats vid Communication Networks Research Group (ComNets), RWTH Aachen University Tyskland. Resultat presenteras som visar effekterna av olika schemaläggning strategier för VoIP kapacitet. Dessa resultat illustrerar hur de begränsade kontroll kanalresurser, särskilt fysiskt Downlink (PDCCH) resurser, påverkar det totala antalet schemaläggningsbart VoIP användare ljud mediaströmmar.

No description available.

Code Division Multiple Access (CDMA) is the technology used in all third generation cellular communications networks, and it is a promising candidate for the definition of fourth generation standards. The wireless mobile channel is usually frequency-selective causing interference among the users in one CDMA cell. Multiuser Transmission (MUT) algorithms for the downlink can increase the number of supportable users per cell, or decrease the necessary transmit power to guarantee a certain quality-of-service. Transmitter-based algorithms exploiting the channel knowledge in the transmitter are also motivated by information theoretic results like the Writing-on-Dirty-Paper theorem. The signal-to-noise ratio (SNR) is a reasonable performance criterion for noise-dominated scenarios. Using linear filters in the transmitter and the receiver, the SNR can be maximized with the proposed Eigenprecoder. Using multiple transmit and receive antennas, the performance can be significantly improved. The Generalized Selection Combining (GSC) MIMO Eigenprecoder concept enables reduced complexity transceivers. Methods eliminating the interference completely or minimizing the mean squared error exist for both the transmitter and the receiver. The maximum likelihood sequence detector in the receiver minimizes the bit error rate (BER), but it has no direct transmitter counterpart. The proposed Minimum Bit Error Rate Multiuser Transmission (TxMinBer) minimizes the BER at the detectors by transmit signal processing. This nonlinear approach uses the knowledge of the transmit data symbols and the wireless channel to calculate a transmit signal optimizing the BER with a transmit power constraint by nonlinear optimization methods like sequential quadratic programming (SQP). The performance of linear and nonlinear MUT algorithms with linear receivers is compared at the example of the TD-SCDMA standard. The interference problem can be solved with all MUT algorithms, but the TxMinBer approach requires less transmit power to support a certain number of users. The high computational complexity of MUT algorithms is also an important issue for their practical real-time application. The exploitation of structural properties of the system matrix reduces the complexity of the linear MUT mthods significantly. Several efficient methods to invert the ystem matrix are shown and compared. Proposals to reduce the omplexity of the Minimum Bit Error Rate Multiuser Transmission mehod are made, including a method avoiding the constraint by pase-only optimization. The complexity of the nonlinear methods i still some magnitudes higher than that of the linear MUT lgorithms, but further research on this topic and the increasing processing power of integrated circuits will eventually allow to exploit their better performance. / Der codegeteilte Mehrfachzugriff (CDMA) wird bei allen zellularen Mobilfunksystemen der dritten Generation verwendet und ist ein aussichtsreicher Kandidat für zukünftige Technologien. Die Netzkapazität, also die Anzahl der Nutzer je Funkzelle, ist durch auftretende Interferenzen zwischen den Nutzern begrenzt. Für die Aufwärtsstrecke von den mobilen Endgeräten zur Basisstation können die Interferenzen durch Verfahren der Mehrnutzerdetektion im Empfänger verringert werden. Für die Abwärtsstrecke, die höhere Datenraten bei Multimedia-Anwendungen transportiert, kann das Sendesignal im Sender so vorverzerrt werden, dass der Einfluß der Interferenzen minimiert wird. Die informationstheoretische Motivation liefert dazu das Writing-on-Dirty-Paper Theorem. Das Signal-zu-Rausch-Verhältnis ist ein geeignetes Kriterium für die Performanz in rauschdominierten Szenarien. Mit Sende- und Empfangsfiltern kann das SNR durch den vorgeschlagenen Eigenprecoder maximiert werden. Durch den Einsatz von Mehrfachantennen im Sender und Empfänger kann die Performanz signifikant erhöht werden. Mit dem Generalized Selection MIMO Eigenprecoder können Transceiver mit reduzierter Komplexität ermöglicht werden. Sowohl für den Empfänger als auch für den Sender existieren Methoden, die Interferenzen vollständig zu eliminieren, oder den mittleren quadratischen Fehler zu minimieren. Der Maximum-Likelihood-Empfänger minimiert die Bitfehlerwahrscheinlichkeit (BER), hat jedoch kein entsprechendes Gegenstück im Sender. Die in dieser Arbeit vorgeschlagene Minimum Bit Error Rate Multiuser Transmission (TxMinBer) minimiert die BER am Detektor durch Sendesignalverarbeitung. Dieses nichtlineare Verfahren nutzt die Kenntnis der Datensymbole und des Mobilfunkkanals, um ein Sendesignal zu generieren, dass die BER unter Berücksichtigung einer Sendeleistungsnebenbedingung minimiert. Dabei werden nichtlineare Optimierungsverfahren wie Sequentielle Quadratische Programmierung (SQP) verwendet. Die Performanz linearer und nichtlinearer MUT-Verfahren MUT-Algorithmen mit linearen Empfängern wird am Beispiel des TD-SCDMA-Standards verglichen. Das Problem der Interferenzen kann mit allen untersuchten Verfahren gelöst werden, die TxMinBer-Methode benötigt jedoch die geringste Sendeleistung, um eine bestimmt Anzahl von Nutzern zu unterstützen. Die hohe Rechenkomplexität der MUT-Algorithmen ist ein wichtiges Problem bei der Implementierung in Real-Zeit-Systemen. Durch die Ausnutzung von Struktureigenschaften der Systemmatrizen kann die Komplexität der linearen MUT-Verfahren signifikant reduziert werden. Verschiedene Verfahren zur Invertierung der Systemmatrizen werden aufgezeigt und verglichen. Es werden Vorschläge gemacht, die Komplexität der Minimum Bit Error Rate Multiuser Transmission zu reduzieren, u.a. durch Vermeidung der Sendeleistungsnebenbedingung durch eine Beschränkung der Optimierung auf die Phasen des Sendesignalvektors. Die Komplexität der nichtlinearen Methoden ist um einige Größenordungen höher als die der linearen Verfahren. Weitere Forschungsanstrengungen an diesem Thema sowie die wachsende Rechenleistung von integrierten Halbleitern werden künftig die Ausnutzung der besseren Leistungsfähigkeit der nichtlinearen MUT-Verfahren erlauben.

Pushing wireless data traffic onto small cells is important for alleviating congestion in the over-loaded macrocellular network. However, the ultimate potential of such load balancing and its effect on overall system performance is not well understood. With the ongoing deployment of multiple classes of access points (APs) with each class differing in transmit power, employed frequency band, and backhaul capacity, the network is evolving into a complex and “organic” heterogeneous network or HetNet. Resorting to system-level simulations for design insights is increasingly prohibitive with such growing network complexity. The goal of this dissertation is to develop realistic yet tractable frameworks to model and analyze load balancing dynamics while incorporating the heterogeneous nature of these networks. First, this dissertation introduces and analyzes a class of user-AP association strategies, called stationary association, and the resulting association cells for HetNets modeled as stationary point processes. A “Feller-paradox”-like relationship is established between the area of the association cell containing the origin and that of a typical association cell. This chapter also provides a foundation for subsequent chapters, as association strategies directly dictate the load distribution across the network. Second, this dissertation proposes a baseline model to characterize downlink rate and signal-to-interference-plus-noise-ratio (SINR) in an M-band K-tier HetNet with a general weighted path loss based association. Each class of APs is modeled as an independent Poisson point process (PPP) and may differ in deployment density, transmit power, bandwidth (resource), and path loss exponent. It is shown that the optimum fraction of traffic offloaded to maximize SINR coverage is not in general the same as the one that maximizes rate coverage. One of the main outcomes is demonstrating the aggressive of- floading required for out-of-band small cells (like WiFi) as compared to those for in-band (like picocells). To achieve aggressive load balancing, the offloaded users often have much lower downlink SINR than they would on the macrocell, particularly in co-channel small cells. This SINR degradation can be partially alleviated through interference avoidance, for example time or frequency resource partitioning, whereby the macrocell turns off in some fraction of such resources. As the third contribution, this dissertation proposes a tractable framework to analyze joint load balancing and resource partitioning in co-channel HetNets. Fourth, this dissertation investigates the impact of uplink load balancing. Power control and spatial interference correlation complicate the mathixematical analysis for the uplink as compared to the downlink. A novel generative model is proposed to characterize the uplink rate distribution as a function of the association and power control parameters, and used to show the optimal amount of channel inversion increases with the path loss variance in the network. In contrast to the downlink, minimum path loss association is shown to be optimal for uplink rate coverage. Fifth, this dissertation develops a model for characterizing rate distribution in self-backhauled millimeter wave (mmWave) cellular networks and thus generalizes the earlier multi-band offloading framework to the co-existence of current ultra high frequency (UHF) HetNets and mmWave networks. MmWave cellular systems will require high gain directional antennas and dense AP deployments. The analysis shows that in sharp contrast to the interferencelimited nature of UHF cellular networks, mmWave networks are usually noiselimited. As a desirable side effect, high gain antennas yield interference isolation, providing an opportunity to incorporate self-backhauling. For load balancing, the large bandwidth at mmWave makes offloading users, with reliable mmWave links, optimal for rate. / text