Les antennes présentes dans la plupart des systèmes communicants comme les véhicules automobiles, les avions et les trains se multiplient et sont soumises à une contrainte d’intégration de plus en plus sévère. De nombreuses techniques de miniaturisation d’antennes existent et passent toutes par un compromis entre la taille et les performances (bande passante et/ou rendement de rayonnement). Pour les systèmes cités ci-dessus, les antennes sont souvent placées devant ou à proximité d’un réflecteur métallique (toit de véhicule, carlingue d’aéronef). Dans ce cas, l’épaisseur de système antennaire est une contrainte majeure et les métamatériaux de type Conducteur Magnétique Artificiel (CMA) ouvrent des perspectives intéressantes grâce à leurs propriétés électromagnétiques non conventionnelles. Cependant, pour les applications sub-GHz (RFID, LTE, PMR…), les CMA sont limités par les dimensions des cellules unitaires nécessaires à leur mise en œuvre (λg/4) ainsi que leur bande réduite de fonctionnement. Réduire leurs dimensions permet de rendre leur utilisation compatible avec le contexte des antennes miniatures intégrées. Ajouter l’agilité fréquentielle permet de palier le problème de la bande passante réduite dans le cas des antennes et des CMA miniaturisés en ajustant le fonctionnement du système antennaire sur une large bande passante. Cette thèse de doctorat propose d’étudier et de développer un nouveau système antennaire à faible profil composé d’une antenne miniature associée à une métasurface compacte reconfigurable en fréquence et compatible avec le standard NB-IoT dans la bande basse LTE (700 MHz – 960 MHz). / Antennas are now very integrated in several connected systems like cars, airplanes and trains. Many antenna miniaturization techniques exist and all go through a compromise between size and performance (bandwidth and/or radiation efficiency). For the systems mentioned above, the antennas are often placed near a metallic reflector (vehicle roof, aircraft cabin). Within this context, Artificial Magnetic Conductors (AMC) present an attractive reflector for low profile antennas which can take advantage of intrinsic zero reflection phase response to boost antenna performance without the need for thick quarter wave backplane. However, for sub-GHz applications (RFID, LTE, PMR ...), AMC are limited by the size of the unit cells necessary for their implementation (λg/4) as well as their reduced operating bandwidth. AMC miniaturization makes their use compatible with small antennas. Adding tunability restores the possibility of adjusting the operating frequency over a large bandwidth. This PhD thesis proposes to study and develop a new electrically small, low-profile antenna based on miniaturized and tunable AMC for the NB-IoT standard in low LTE band (700 MHz – 960 MHz).

Artificial magnetic materials (AMMs) are a type of metamaterials which are engineered to exhibit desirable magnetic properties not found in nature. AMMs are realized by embedding electrically small metallic resonators aligned in parallel planes in a host dielectric medium. In the presence of a magnetic field, an electric current is induced on the inclusions leading to the emergence of an enhanced magnetic response inside the medium at the resonance frequency of the inclusions. AMMs with negative permeability are used to develop single negative, or double negative metamaterials. AMMs with enhanced positive permeability are used to provide magneto-dielectric materials at microwave or optical frequencies where the natural magnetic materials fail to work efficiently. Artificial magnetic materials have proliferating applications in microwave and optical frequency region. Such applications include inversely refracting the light beam, invisibility cloaking, ultra miniaturizing and frequency bandwidth enhancing low profile antennas, planar superlensing, super-sensitive sensing, decoupling proximal high profile antennas, and enhancing solar cells efficiency, among others. AMMs have unique enabling features that allow for these important applications. Fundamental limitations on the performance of artificial magnetic materials have been derived. The first limitation which depends on the generic model of permeability functions expresses that the frequency dispersion in an AMM is limited by the desired operational bandwidth. The other constraints are derived based on the geometrical limitations of inclusions. These limitations are calculated based on a circuit model. Therefore, a formulation for permeability and magnetic susceptibility of the media based on a circuit model is developed. The formulation is in terms of a geometrical parameter that represents the geometrical characteristics of the inclusions such as area, perimeter and curvature, and a physical parameter that represents the physical, structural and fabrication characteristics of the medium. The effect of the newly introduced parameters on the effective permeability of the medium and the magnetic loss tangent are studied. In addition, the constraints and relations are used to methodically design artificial magnetic material meeting specific operational requirements. A novel design methodology based on an introduced analytical formulation for artificial magnetic material with desired properties is implemented. The synthesis methodology is performed in an iterative four-step algorithm. In the first step, the feasibility of the design is tested to meet the fundamental constraints. In consecutive steps, the geometrical and physical factors which are attributed to the area and perimeter of the inclusion are synthesized and calculated. An updated range of the inclusion's area and perimeter is obtained through consecutive iterations. Finally, the outcome of the iterative procedure is checked for geometrical realizability. The strategy behind the design methodology is generic and can be applied to any adopted circuit based model for AMMs. Several generic geometries are introduced to realize any combination of geometrically realizable area and perimeter (s,l) pairs. A realizable geometry is referred to a contour that satisfies Dido's inequality. The generic geometries introduced here can be used to fabricate feasible AMMs. The novel generic geometries not only can be used to enhance magnetic properties, but also they can be configured to provide specific permeability with desired dispersion function over a certain frequency bandwidth with a maximum magnetic loss tangent. The proposed generic geometries are parametric contours with uncorrelated perimeter and area function. Geometries are configured by tuning parameters in order to possess specified perimeter and surface area. The produced contour is considered as the inclusion's shape. The inclusions are accordingly termed Rose curve resonators (RCRs), Corrugated rectangular resonators (CRRs) and Sine oval resonators (SORs). Moreover, the detailed characteristics of the RCR are studied. The RCRs are used as complementary resonators in design of the ground plane in a microstrip stop-band filter, and as the substrate in design of a miniaturized patch antenna. The performance of new designs is compared with the counterpart devices, and the advantages are discussed.

Artificial magnetic materials (AMMs) are a type of metamaterials which are engineered to exhibit desirable magnetic properties not found in nature. AMMs are realized by embedding electrically small metallic resonators aligned in parallel planes in a host dielectric medium. In the presence of a magnetic field, an electric current is induced on the inclusions leading to the emergence of an enhanced magnetic response inside the medium at the resonance frequency of the inclusions. AMMs with negative permeability are used to develop single negative, or double negative metamaterials. AMMs with enhanced positive permeability are used to provide magneto-dielectric materials at microwave or optical frequencies where the natural magnetic materials fail to work efficiently. Artificial magnetic materials have proliferating applications in microwave and optical frequency region. Such applications include inversely refracting the light beam, invisibility cloaking, ultra miniaturizing and frequency bandwidth enhancing low profile antennas, planar superlensing, super-sensitive sensing, decoupling proximal high profile antennas, and enhancing solar cells efficiency, among others. AMMs have unique enabling features that allow for these important applications. Fundamental limitations on the performance of artificial magnetic materials have been derived. The first limitation which depends on the generic model of permeability functions expresses that the frequency dispersion in an AMM is limited by the desired operational bandwidth. The other constraints are derived based on the geometrical limitations of inclusions. These limitations are calculated based on a circuit model. Therefore, a formulation for permeability and magnetic susceptibility of the media based on a circuit model is developed. The formulation is in terms of a geometrical parameter that represents the geometrical characteristics of the inclusions such as area, perimeter and curvature, and a physical parameter that represents the physical, structural and fabrication characteristics of the medium. The effect of the newly introduced parameters on the effective permeability of the medium and the magnetic loss tangent are studied. In addition, the constraints and relations are used to methodically design artificial magnetic material meeting specific operational requirements. A novel design methodology based on an introduced analytical formulation for artificial magnetic material with desired properties is implemented. The synthesis methodology is performed in an iterative four-step algorithm. In the first step, the feasibility of the design is tested to meet the fundamental constraints. In consecutive steps, the geometrical and physical factors which are attributed to the area and perimeter of the inclusion are synthesized and calculated. An updated range of the inclusion's area and perimeter is obtained through consecutive iterations. Finally, the outcome of the iterative procedure is checked for geometrical realizability. The strategy behind the design methodology is generic and can be applied to any adopted circuit based model for AMMs. Several generic geometries are introduced to realize any combination of geometrically realizable area and perimeter (s,l) pairs. A realizable geometry is referred to a contour that satisfies Dido's inequality. The generic geometries introduced here can be used to fabricate feasible AMMs. The novel generic geometries not only can be used to enhance magnetic properties, but also they can be configured to provide specific permeability with desired dispersion function over a certain frequency bandwidth with a maximum magnetic loss tangent. The proposed generic geometries are parametric contours with uncorrelated perimeter and area function. Geometries are configured by tuning parameters in order to possess specified perimeter and surface area. The produced contour is considered as the inclusion's shape. The inclusions are accordingly termed Rose curve resonators (RCRs), Corrugated rectangular resonators (CRRs) and Sine oval resonators (SORs). Moreover, the detailed characteristics of the RCR are studied. The RCRs are used as complementary resonators in design of the ground plane in a microstrip stop-band filter, and as the substrate in design of a miniaturized patch antenna. The performance of new designs is compared with the counterpart devices, and the advantages are discussed.

The concept for a novel new antenna design is presented and investigated for application to ground penetrating radar (GPR). The proposed new antenna design is called the shielded magnetic bowtie antenna (MBA). As the name suggests, it is predominately constructed from a bowtie-shaped volume of magnetic material that is fed from the centre of the structure by a small magnetic loop antenna. This thesis develops the magnetic antenna concept and investigates its potential for GPR predominately through numerical modelling. However, a significant part of the investigation concentrates on validating the numerical modelling technique developed to study the shielded MBA by comparing the results with measurements obtained from a scale model constructed to operate in the watertank antenna test facility, a controlled environment for GPR antenna research. The broadband properties required for GPR antennas are achieved uniquely with the shielded MBA design by a combination of the antenna shape being defined in terms of angles and an inherent magnetic loss mechanism within the antenna material structure. The design also affords an intrinsically placed antenna shield that has the potential for mitigating problems typically experienced with shielding electric dipole antennas. Antenna shielding is an important consideration for GPR antenna designers, especially given the recent US government (FCC) changes that restrict radiated energy emissions within the regulated spectrum used by GPR systems. In addition to providing the intended directional radiation properties, the magnetic antenna shield also provides an elegant solution for a low-loss wideband balun, allowing the antenna to be effectively fed from an unbalanced coaxial transmission line. Other important aspects of the proposed design are discussed in relation to the requirements for GPR antennas. Numerical models of the magnetic antenna concept show encouraging bandwidth results. For example, from a simple comparison with an equivalent sized electric bowtie antenna model, the effective gain bandwidth of the magnetic antenna is found to be at least 3-octaves compared to approximately 2-octaves for the electric bowtie. The shielded magnetic antenna achieves a gain of approximately 2 dB, compared to 5 dB for the unshielded electric bowtie antenna. However, it is noted that the magnetic antenna models contain significantly more loss compared to the electric bowtie model. The shielded MBA design emerged from a theoretical investigation of electrically small GPR antennas, given that the initial thesis objective was to investigate ways of improving low frequency GPR antennas. In general, GPR systems are operated with electric dipole antennas, such as the electric bowtie. Interestingly, the electrically small antenna investigation revealed that only the small magnetic loop (i.e., magnetic dipole) antenna can be constructed to approach, arbitrarily closely, the fundamental bandwidth limit for small antennas. This surprising and counter intuitive result is shown to be theoretically achievable with the use of magnetic materials. For the small loop antenna, energy stored within the antenna structure can be avoided by filling the antenna sphere with a perfect magnetic material. This theoretical argument is discussed and supported by numerically modelled results. The electrically small antenna investigation presented in this thesis extends to include the influence that proximity to a lossy dielectric half-space has, on improving the antenna impedance bandwidth. This investigation is of general interest for GPR; it is performed numerically and supported by measurements conducted on an experimental loop antenna situated at various heights above the ground. These results provide support for the hypothesis that a magnetic antenna may experience less influence from near-field changes in the dielectric properties of the ground compared to the equivalent sized electric field antenna.

Electroconductive composites are modern materials that are commonly used in many industries such as the construction industry among others. For example these materials can be useful as sensors for monitoring changes in constructions. The aim of this thesis is the research of electrically conductive silicate composite based on secondary raw materials. The design of this composite is based on the development of its own mixtures and experimental verification of the effect of the structure. The introduction part consists of a detailed analysis of 15 materials. Samples of the 5 fine and 2 coarse electrically conductive fillers were tested. Composite with filler Condufit C4 was selected as representative for type of fine fillers. Composite with filler Supragraphite C300 was selected as representative for type of coarse fillers. The selection of the composites was based on the impedance of the fabricated composites with these fillers. Subsequently, the individual components of the primary mixture were substituted. The cement was replaced by high-temperature fly ash in the amount of 20, 30, and 40 %, the aggregate of a similar fraction was replaced by steel sawdust, and the primary electrically conductive fillers were replaced by secondary ones in the amount of 30 and 50 %. All proposed replacements reduced the impedance of the composite. The most effective replacement for impedance reduction was replacement with waste graphite (up to 92 % reduction), which also slightly improved the mechanical properties of the composite. The result of this thesis is an optimized electrically conductive composite based on secondary raw materials with a fine type of filler with 30 % replacement by waste graphite "odpad vysavač"which achieves an impedance of 5 ohms. The partial goal of this thesis is a verification of the influence of moisture on the impedance of composites. Results are significantly affected by moisture when using the coarse type of filler, when using the fine type are not.

No description available.

В работе представлены результатыисследования метода, который позволяет увеличить полосу частот электрически малой антенны с помощью “нефостеровской цепи”на основе операционного усилителя. Были получены графики, которые позволяют оценить входное реактивное сопротивление и полосу частот электрически малой антенны с представленным методом расширения полосы частот. / The paper presents the results of a study of the method, which makes it possible to increase the frequency band of an electrically small antenna by means of a "Non-foster circuit"with operational amplifier. The graphs were obtain, which allow estimating the input reactance and the bandwidth of an electrically small antenna with the method of bandwidth extension represented.

В работе представлены результатыисследования метода, который позволяет увеличить полосу частот электрически малой антенны с помощью “нефостеровской цепи”.Также были представлены классические методы расширения полосы частот антенны с помощью индуктивности и колебательного контура, чтобы сравнить их эффективность с исследуемым методом. Были получены графики, которые позволяют оценить входное реактивное сопротивление и полосу частот электрически малой антенны со всеми представленными методами расширения полосы частот. / The paper presents the results of a study of the method, which makes it possible to increase the frequency band of an electrically small antenna by means of a "Non-foster circuit". Also, classical methods for extending the frequency band of the antenna with the help of inductance and a vibrational circuit were presented to compare their effectiveness with the method being studied.

No description available.

No description available.