The objective of this research is to develop a customized hardware-in-the-loop system that is used to test Electronic Stability Program (ESP) systems to prevent heavy truck rollovers when navigating horizontal roadway curves. While most of the published literature on electronic stability control focuses on the effectiveness of stability systems in passenger cars, very few researchers have considered its application as it pertains to commercial vehicles. Detailed crash data that have been extracted from the crashes that are represented in the Large Truck Crash Causation Study database have been used to draw conclusions regarding the main cause of the crashes and the geometry of the road upon which the crashes occurred. Those crash scenarios were run through a hardware-in-the-loop system that communicates between the TruckSim software, a vehicle dynamics based simulation program, and a real-time tractor-trailer braking rig. The simulations were first run without the ESP enabled to determine the critical speed which will cause the truck to roll, then the same simulation runs were executed with the Bendix stability system enabled to determine the difference in speeds in which a rollover is inevitable with and without the technology. A third speed that represents the lowest speed in which the stability system activates was also determined. As requested by the National Highway Traffic Safety Administration (NHTSA), this study also serves as a comparison between the Bendix system and the Meritor WABCO system which has already been tested by the University of Michigan Transportation Research Institute. / Master of Science

Thesis(M.S.)--Auburn University, 2005. / Abstract. Includes bibliographic references.

Thesis(M.S.)--Auburn University, 2007. / Abstract. Vita. Includes bibliographic references.

Thesis(M.S.)--Auburn University, 2008. / Abstract. Vita. Includes bibliographic references (p.96-99).

No description available.

No description available.

In the presented work, first principle studies on electronic structure, stability, and magnetic properties of metal chalcogenide, CrnTem clusters have been carried out within a density functional framework using generalized gradient functions to incorporate the exchange and correlation effects. The energetic and electronic stability was investigated, and it was found that they are not always correlated as seen in the cluster Cr6Te8 which has smaller gap between its HOMO (Highest Occupied Molecular Orbital) and LUMO (Lowest Unoccupied Molecular Orbital) and a high electron affinity of 3.39 eV indicating lower electronic stability whereas higher fragmentation energy indicating energetic stability. The high electron affinity shows that the stability of Cr6Te8 cluster can be enhanced by adding charge donating ligands including PEt3 to form stable Cr6Te8(PEt3)6 clusters as seen in experiments. The other cluster of interest was Cr4Te6 in which energetic stability was accompanied with electronic inertness marked by its large HOMO-LUMO gap, non-magnetic ground state and high fragmentation energy.

This thesis contains the design and simulation test results for the implementation of a new all-wheel drive (AWD) torque vectoring (TV) control system. A separate algorithm using standard control methods is included in this study for a comparison. The proposed controller was designed to be applied to an AWD independent drive electric vehicle, however the main concepts can be re-purposed for other vehicle drive train configurations. The purpose of the control system is to assist the driver in achieving a desired vehicle trajectory whilst also maintaining stability and control of the vehicle. This is accomplished by measuring various real time parameters of the vehicle and using this information as feedback for the control system to act on. The focus of this thesis resides on the controller. Hence, this study assumes perfect observation of feedback parameters, therefore some uncertainties are not accounted for. Using feedback parameters, the control system will manage wheel slip whilst simultaneously generating a torque around the center of gravity of the vehicle by applying a torque differential between the left and right wheels. The proposed TV algorithm is simulated in MATLAB/Simulink along with another separate TV algorithm for comparison. Both algorithms are comprised of two main parts: a slip ratio controller applied to each wheel individually and stability controller that manages yaw rate and side slip of the vehicle. The new algorithm leverages the super twisting algorithm for the slip ratio controller and uses a fusion of a linear quadratic regulator with the integral term of a super twisting algorithm to implement the yaw rate and side slip controller. The other algorithm used for comparison derives its implementation for the slip ratio controller and yaw rate and side slip controllers from simple and standard first order sliding mode control methods. Both control algorithms were tested in three different main tests: anti-lock braking, sine dwell (SD) steering, and constant steering angle (CSA) tests. To increase the comprehensive nature of the study, the SD and CSA tests were simulated at 3 speeds (30,50, and 80 mph) and the steering angle parameter was varied from 2 to 24 degrees in increments of 2. The result of this study proves that the proposed controller is a feasible option for use in theory. Simulated results show advantages and disadvantages of the new controller with respect to the standard comparison controller. Both controllers are also shown to provide positive impacts on the vehicle response under most test conditions.

No description available.

This dissertation details the methods and analysis of extensive physical tests and simulation conducted by the Center for Vehicle Systems and Safety (CVeSS) at Virginia Tech on the maneuverability, roll-stability, and brake type performance of 33-ft double trailers. Little literature exists for 33-ft doubles because they are uncommon on the U.S. roads due to current federal restrictions limiting long-combination vehicles to 28-ft doubles. With the continual rise in e-commerce, however, there is a push by package carriers on legislation to permit carriers to introduce 33-ft doubles into their fleets. Three separate studies detailed herein highlight 33-ft double trailers' off-tracking, roll-stability with stability control systems, and brake type influence on braking performance. The first study compares low-speed off-tracking of a 33-ft double to 28-ft double and 53-ft single configurations via simulation and full-scale tests. Novel numerical tractrix models are introduced and compared to existing models commonly used to evaluate low-speed off-tracking of long combination vehicles (LCVs). Unlike pre-existing models, accuracy of one of the proposed models is largely unaffected by input path resolution and regularity—a significant benefit for reducing computational cost and easing implementation for many applications. Full-scale tests are conducted at Virginia Tech and an extensive uncertainty analysis is detailed for the test procedure and measurements. Field tests compare favorably with simulations for all tested maneuvers and trailer configurations and clearly demonstrate the order from least to most off-tracking as 28-ft double, 33-ft double, and 53-ft single. The 33-ft doubles have slightly larger off-tracking than 28-ft doubles, whereas 53-ft singles have substantially larger off-tracking than 28-ft and 33-ft doubles. The second study evaluates 33-ft double straight-rail trailers rollover propensity with different stability control system implementations: stock (none), tractor electronic stability control (ESC), trailer roll-stability control (RSC), and RSC+ESC. Extensive test vehicle instrumentation and structural reinforcement are detailed for the test preparations. Tests are conducted on a test track with either driver or robot steering. On their own, both ESC and RSC clearly reduce the rollover propensity of the trailers for all maneuvers, and the trailers exhibit the highest roll-stability when both RSC and ESC are active. The tested ESC and RSC modules are off-the-shelf products from industry suppliers chosen by the program sponsor. The third study compares trailer drum and disc brake performance in three conditions: straight-line braking distance, brake type influence on RSC performance, and roll dynamics in a combined braking and turning maneuver. A braking robot is designed, fabricated, and implemented to provide precise and repeatable brake pedal application. Test results suggest that disc brakes tend to provide reduced braking distance and are less susceptible to brake fade than drum brakes. Anti-lock braking system (ABS) and suspension dynamics react differently to the two brake types. Small, noticeable differences in RSC performance are evident between the two brake types. Within the test limitations, rollover dynamics were not clearly different between the two brake types for braking-in-turn maneuvers, performed for a large range of entry speeds and brake activation delay relative to the start of steering. / Doctor of Philosophy / Due to their large size, mass, and high center-of-gravity, heavy vehicles, especially long combination vehicles (LCVs) require a substantial amount of space to negotiate turns, long distances to brake from highway speeds to a stop and are susceptible to rollover. Combination vehicles on the U.S. roads are commonly in 53-ft single trailer or 28-ft double trailer configurations. With the continual rise of e-commerce, package carriers are pursuing 33-ft double trailers to increase each vehicle's cargo volume. Before introducing these trailers into a fleet, there is a need to understand (1) if 33-ft doubles can negotiate existing routes traveled by 28-ft double and 53-ft single configurations, (2) if 33-ft doubles can benefit from existing stability control systems, and (3) how trailer brake types perform on 33-ft doubles. Three separate studies are conducted to address these topics. The first study compares off-tracking for the three mentioned trailer configurations through low-speed, real-world maneuvers via physical full-scale tests and simulation. Off-tracking is a metric illustrative of maneuverability and is defined as the relative distance in paths of the rearmost axle to the lead steer axle. New mathematical models are introduced and used to simulate vehicle motion through low-speed maneuvers. The simulation and field tests determine that, for all tested maneuvers, the order from smallest to largest off-tracking is 28-ft double, 33-ft double, and 53-ft single configurations, with the 33-ft doubles having slightly larger off-tracking than 28-ft doubles. This suggests that 33-ft doubles can travel through routes typically traveled by a 53-ft single but need slightly more space on the road than a 28-ft double. The second study tests 33-ft double trailers with and without stability control systems. Tests, conducted at a test track, are designed to replicate real-world maneuvers that induce trailer rollover. It is found that the 33-ft double trailers are clearly less likely to rollover with the tested stability enhancement systems than without. The tests also illustrate that the different tested control systems' effectiveness in reducing rollover propensity is maneuver dependent. The third study tests the braking distance, brake influence on the stability control systems, and rollover dynamics while braking-in-turn for two different types of brakes, drum brakes and disc brakes. Small but evident differences in the performance of the two brake types suggest disc brakes could provide shorter stopping distance and time at highway speeds, compared with drum brakes. The studies detailed in this dissertation provide valuable information on 33-ft doubles dynamics and provide guidance for their safe introduction on the U.S. roadways.