No description available.

No description available.

No description available.

The goal of this thesis is to develop more effective quantitative procedures to evaluate the stability of deteriorated metal culverts and a better understanding of the deteriorated culverts' behaviour through non-destructive testing, full scale experiments and numerical analyses. First, three design cases were examined using numerical analysis to study the effects of corrosion, burial depth and staged construction on the capacity of deteriorated steel culverts. Then, a method to measure the remaining wall thickness of two 1.8 m diameter corroded metal culverts using ultrasonic device was developed. Both culverts were then buried in the test pit at Queen's University and tested under nominal and working vehicle loads at 0.9m cover and 0.6m cover. The more heavily corroded structure (CSP1) was tested up to its ultimate limit state, inducing local bending across the crown, as well as local buckling of the remnants of the corrugated steel wall between perforations at the haunches. The results suggest that the single axle pads interact to influence the culvert's behaviour despite the shallow cover used in these experiments. CSP1 was able to carry the working load and did not fail until reaching 340 kN, which was equal to 90% of the fully factored load. The experiment suggests that less deteriorated metal culverts (as compared to CSP1) may have the required capacity. Two finite element packages, CANDE and ABAQUS, were used to perform the numerical investigation and the AASHTO and CHBDC approaches were then used to calculate the thrust force in the culverts. Although the numerical analysis produced conservative values for the thrust forces, it failed to capture the non-linear behaviour of both specimens in the experiments. Both the AASHTO and the CHBDC approaches produced unconservative thrust forces compared to experimental results while numerical analysis using Moore's spreading factor produced the most conservative results in terms of thrust. The analysis suggests that CANDE could be used to predict thrust forces in less deteriorated metal culverts. A procedure to assess the stability of deteriorated corrugated metal culverts based on quantitative data was developed using the numerical analysis and experimental results. / Thesis (Master, Civil Engineering) -- Queen's University, 2013-01-30 12:56:17.945

Research on auctions that involve more than one identical item for sale was,almost non-existing in the 90’s, but has since then been getting increasing attention. External incentives for this research have come from the US spectrum, sales, the European 3G mobile-phone auctions,  and Internet auctions. The policy relevance and the huge amount of money involved in many of them have helped the theory and experimental research advance. But in auctions where values are equal across bidders, common value auctions, that is, when the value depends on some outside parameter, equal to all bidders, the research is still embryonic. This thesis contributes to the topic with three studies. The first uses a Bayesian game to model a simple multi-unit common value auction, the task being to compare equilibrium strategies and the seller’s revenue from three auction formats; the discriminatory, the uniform and the Vickrey auction. The second study conducts an economic laboratory experiment on basis of the first study. The third study comprises an experiment on the multi-unit common value uniform auction and compares the dynamic and the static environments of this format. The most salient result in both experiments is that subjects overbid. They are victims of the winner’s curse and bid above the expected value, thus earning a negative profit. There is some learning, but most bidders continue to earn a negative profit also in later rounds. The competitive effect when participating in an auction seems to be stronger than the rationality concerns. In the first experiment, subjects in the Vickrey auction do somewhat better in small groups than subjects in the other auction types and, in the second experiment, subjects in the dynamic auction format perform much better than subjects in the static auction format; but still, they overbid. Due to this overbidding, the theoretical (but not the behavioral) prediction that the dynamic auction should render more revenue than the static fails inthe second experiment. Nonetheless, the higher revenue of the static auction comes at a cost; half of the auctions yield negative profits to the bidders, and the winner’s curse is more severely widespread in this format. Besides, only a minority of the bidders use the equilibrium bidding strategy.The bottom line is that the choice between the open and sealed-bid formats may be more important than the choice of price mechanism, especially in common value settings.

Micro drilling has been applied in the interconnection and precision manufacturing industries extensively. As a promising machining technique, Ultrasonically Assisted Drilling (UAD) has become increasingly popular in both academia and industry in recent years. In this thesis, modelling techniques and experiments for Ultrasonically Assisted Micro Drilling (UAMD) are investigated. Representative work on modelling of micro drills and UAD has been documented and categorised. Existing gaps in the literature are identified and the aims of this research are formulated. Using the Finite Element (FE) technique, a hybrid model is developed to realise modelling for the whole drill bit without compromising the computation efficiency, even when the drill has a complicated geometry (small diameter flute, multiple step shanks, etc). A specific drill model (Φ0.3 mm diameter, 2 step shanks) is chosen for a case study in order to evaluate the model. The hybrid tool shows sufficiently accurate results and impressive computation efficiency in the evaluation. For vibration modelling, force modelling and experimental work, a standard Φ1 mm drill with 1 step shank is used across the chapters. First of all, FE analysis is conducted on the whole drill and normal modes are solved with boundary condition as fixed simply supported. A 2 Degree-of-Freedom (DOF) model is then built considering rotation and the ultrasonic excitation to solve the transverse vibration with boundary conditions consistent with the FE model. The asymmetric geometric characteristics of the drill bit are taken account of through using the first two fundamental modes in the FE model. Potential parametric resonances are discussed in the numerical simulation. Other vibration characteristics are also discussed with varying parameters such as ultrasonic frequency, ultrasonic amplitude and rotational speed. In order to extend the vibration model, a nonlinear thrust force model has been developed for incorporation into the 2 DOF model. The force model considers ultrasonic parameters, feed rate, material properties and the nonlinearity of the UAMD process. Force reduction during the UAMD process is explained qualitatively with the model and a full range of feed rates have been simulated to study their effect on the force reduction. The limitations of this model have also been explained. A high speed UAMD system was designed to examine the effects of key parameters. Experiments with different ultrasonic frequencies, amplitudes and rotational speeds were conducted and the influences of these parameters on thrust force were investigated. With the thrust force data from these experiments, a correlation study to the simulation results based on the force model is carried out. The study identifies the limitations on the current one dimensional force model and leads to recommendations for the further development of the force model. Further work is identified for both modelling and experiments, and the present models can be expanded to suit the research and development of UAMD techniques.

The efficient identification of photons is a crucial aspect in the search for the Higgs boson at ATLAS. With the high luminosity and collision energies provided by the Large Hadron Collider, rejection of backgrounds to photons is of key importance. It is often not feasible to fully simulate background processes that require large numbers of events, due to processing time and disk space constraints. The standard fast simulation program, ATLFAST-I, is able to simulate events ∼1000 times faster than the full simulation program but does not always provide enough detailed information to make accurate background estimates. To bridge the gap, a set of photon reconstruction efficiency parameterisations, for converted and unconverted photons, have been derived from full simulation events and subsequently applied to ATLFAST-I photons. Photon reconstruction efficiencies for isolated photons from fully simulated and ATLFAST-I, plus parameterisations, events are seen to agree within statistical error. A study into a newly proposed Two Higgs Doublet Model channel, gg → H → hh → γγγγ, where the light Higgs (h) boson is fermiophobic, has been investigated. The channel is of particular interest as it exploits the large production cross-section of a heavy Higgs (H) boson via gluon-fusion at the LHC in conjunction with the enhanced branching ratio of a light fermiophobic Higgs (h) boson to a pair of photons. This channel is characterised by a distinct signature of four high pT photons in the final state. Samples of signal events have been generated across the (mh,mH) parameter space along with the dominant backgrounds. An event selection has been developed with the search performed at generator-level. In addition, the search was also performed with simulated ATLFAST-I events utilising the above photon reconstruction efficiency parameterisations. For both analyses, the expected upper limit on the cross-section at 95% confidence level is determined and exclusion regions of the (mh,mH) parameter space are defined for integrated luminosities of 1 f b−1 and 10 f b−1 in seven fermiophobic model benchmarks.

The search potential of a Standard Model Higgs boson in the Vector Boson Fusion production mechanism with Higgs boson decaying to two leptons and two neutrinos via decay to two Z bosons with the ATLAS detector is investigated. The ATLAS detector is a general purpose detector in operation at CERN measuring proton-proton collisions produced by the Large Hadron Collider. This channel has been shown to have high sensitivity at large Higgs mass, where large amounts of missing energy in the signal provide good discrimination over expected backgrounds. This work takes a first look at whether the sensitivity of this channel may be improved using the remnants of the vector boson fusion process to pro- vide extra discrimination, particularly at lower mass where sensitivity of the main analysis is reduced because of lower missing energy. Simulated data samples at centre of mass energy 7 Te V are used to derive signal significances over the mass range between 200-600 Ge V / c2. Because of varying signal properties with mass, a low and a high mass event selection were developed and optimized. A comparison between simulated and real data (collected in 2010) is made of variables used in the analysis and the effect of pileup levels corresponding to those in the 2010 data is investigated. Possible methods to estimate some of the main backgrounds to this search are described and discussed. The impact • of important theoretical and detector related systematics are taken into account. Final results are presented in the form of 95 % Confidence Level exclusion limits on the signal cross section relative to the SM prediction as a function of Higgs boson mass, based on an integrated luminosity of 33.4 pb -1 of data collected during 2010.

The usage of statistical methods in the production industry has resulted in quality improvements for several organisations during the last decade. However, advanced statistical methods are still underutilised and underappreciated in quality improvement programs and projects in many companies. Therefore it is of interest to investigate how these methods can be used for quality improvements in the production industry. A case study was conducted at Teufelberger’s wire rope production plant in Wels, Austria. Wire rope type BS 909 was studied by utilising the arsenal of tools and methods that Six Sigma provides, with an emphasis on statistical methods -- especially Design of Experiments. Teufelberger is currently (2016) experiencing diameter issues along the rope and it has been found through customer reclamations and quality controls in the production that the variation in a production lot can be substantial. Furthermore, there is no master setting of process parameters and each operator has their own way of setting and adjusting them, as there are different ways to achieve a product which is within given tolerances. The purpose of this study is to investigate how statistical tools can be applied to minimise variance in a Teufelberger rope manufacturing process, by conducting a case study utilising the quality improvement methodology DMAIC. Experiments were conducted in the following four sub processes which produce input components used during the manufacturing of BS909: KL-A, KL-B, IL and Al. In KL-A the following main effects were identified as significant: Postformers Spin and Postformers Diameter. In KL-B the main effect Postformers Spin was significant. In IL the following main effects were identified as significant: Compacting device, Postformers Spin and Postformers Diameter. In AL the main effect Compacting device was significant. Based on the conclusion derived from analysing these experiments theoretical master setups were created in order to address the variance issue and standardise process parameters. Further verification testing must be conducted in order to verify and tune the proposed master setups before they can be utilised. / Det senaste årtiondet har användningen av statistiska metoder inom tillverkningsindustrin resulterat i kvalitetsförbättringar för flera organisationer men dessa metoder är fortfarande undervärderade och utnyttjas ej till fullo inom program och projekt för kvalitetsförbättringar. Därför är det av intresse att undersöka hur dessa metoder kan användas för kvalitetsförbättringar inom tillverkningsindustrin. Vid en av Teufelbergers produktionsanläggningar av stålvajrar i Wels, Österrike, har en fallstudie med kvalitetsförbättringsmetodiken DMAIC genomförts. Stålvajer typ BS 909 har studerats genom att använda den arsenal av verktyg och metoder som Six Sigma innefattar, med betoning på statistiska metoder och särskilt försöksplanering. Teufelberger hade för tillfället problem med främst diametern av stålvajern. Det har visat sig genom kundreklamationer och kvalitetskontroller i produktionen att variationen i en produktionsserie kan vara betydande. Dessutom finns det ej några dokumenterade optimala inställningar av processparametrar så varje maskinoperatör har sitt eget sätt att ställa in och justera processparametrarna. Detta är möjligt då det finns olika kombinationer av  parameterinställningar som kan ge en produkt som är inom givna toleranser. Syftet med denna studie är att undersöka hur statistikverktyg kan användas för att minimera variansen i en tillverkningsprocess av stålvajer hos företaget Teufelberger, detta genom att utföra en fallstudie med kvalitetsförbättringsmetodiken DMAIC Experiment utfördes i följande fyra processer som producerar ingående komponenter som används vid tillverkningen av BS909: KL-A, KL-B, IL och Al. I processen för KL-A identifierades följande huvudeffekter som aktiva;  Postformers-Spin och Postformers-Diameter. Den enda huvudeffekt som identifierades vara aktiv för KL-B var Postformers-Spin. För IL var följande huvudeffekter aktiva: Compacting device, Postformers-Spin och Postformers-Diameter. I processen AL var endast huvudeffekten Compacting device aktiv. Baserat på det resultat som framkom vid analysen av dessa experiment har nya teoretiskt optimala inställningar beräknats, som förväntas minska variationen i responsvariabeln diameter. De nya rekommenderade inställningarna bör tills vidare kunna fungera som ny standard för produktionen, men verifieringsförsök bör ändå utföras för att bekräfta och finjustera  inställningarna.

Slamming of marine planing craft is expected to arise due to the high speed nature of their operating conditions. High hydrodynamic forces are inevitably induced causing the shell plating to deflect, which in turn can influence the flow physics surrounding the hull. In order to study the hull’s hydroelastic response due to a slamming event, wedge drop experiments were performed with an aluminum wedge of 57 inches in length, 47 inches in breadth, and 20 degree deadrise with 1/4 in. thick unstiffened bottom panels. The elastic behavior of the hull plating was measured via two methods. The first method uses strain gages to analyze the wedge’s deadrise panel deflections, and the second method is a Stereoscopic- Digital Image Correlation (S-DIC) technique. In the present investigation, an S-DIC code has been developed and utilized to study the deflections and to advance the capabilities of future research. Comparisons are made between the methods and also with theoretical studies. The deflections measured are approximately 0.1 in. on a panel spanning 24.5 inches, and the predictions made using S-DIC and strain gages differ by approximately 23%.