Annular gas seal clearances were simulated with closely spaced parallel plates using a Flat?Plate tester. The device is designed to measure the pressure gradient along the test specimen. The main function of the Flat?Plate tester is to provide friction factor data and measure dynamic pressure oscillations. A detailed description of the test facility is described, and a theory for determining the friction factor is reviewed. Three clearances were investigated: 0.635, 0.381, and 0.254 mm. Tests were conducted at three different inlet pressures (84, 70, and 55 bars), producing Reynolds numbers range from 50,000 to 700,000. Three surface configurations were tested including smooth?on-smooth, smooth?on?hole, and hole?on?hole. The Hole?pattern plates are identical with the exception of the hole depth. The results indicate that, for the smooth?on?smooth and smooth?on?hole configurations, the friction factor remains constant or increases slightly with increasing Reynolds numbers. Moreover, the friction factor increases as the clearance between the plates increases. However, the results from the hole?on-hole configurations are quite different. A "friction?factor jump" phenomenon was observed, and the Helmholtz frequency was detected on the frequency spectra.

This thesis presents the experiment study results on the local heat transfer coefficients for air jet impinging on a flat rectangle board. A transient thermochromatic liquid crystal technique is used to visualize and record isotherms on an impingement surface. The parameter studied include Reynolds number¡]Re=108,142,170¡^,jet height from the rectangular board¡]H/D=0.086,0.172,0.259,0.345,0.431,0.52¡^, and size of outlet¡]B/D=1.45,1.86,2.41¡^. The correlation of average Nusselt number is curve-fitted with Re,H/D and B/D . According to the present study,heat transfer is best when the Reynolds number is large,the jet height is small,and the outlet area is large .

No description available.

The present study considers steady laminar two-dimensional incompressible flow over both in-line and staggered flat tube bundles used in heat exchanger applications. The effects of various independent parameters, such as Reynolds number (Re), Prandtl number (Pr), length ratio (L/Da), and height ratio (H/Da), on the pressure drop and heat transfer were studied. A finite volume based FORTRAN code was developed to solve the governing equations. The scalar and velocity variables were stored at staggered grid locations. Scalar variables (pressure and temperature) and all thermophysical properties were stored at the main grid location and velocities were stored at the control volume faces. The solution to a one-dimensional convection diffusion equation was represented by the power law. The locations of grid points were generated by the algebraic grid generation technique. The curvilinear velocity and pressure fields were linked by the Semi-Implicit Method for Pressure Linked Equations (SIMPLE) algorithm. The line-by-line method, which is a combination of the Tri-Diagonal Matrix Algorithm (TDMA) and the Gauss-Seidel procedure, was used to solve the resulting set of discretization equations. The result of the study established that the flow is observed to attain a periodically fully developed profile downstream of the fourth module. The strength increases and the size of the recirculation gets larger as the Reynolds number increases. As the height ratio increases, the strength and size of the recirculation decreases because the flow has enough space to expand through the tube passages. The increase in length ratio does not significantly impact the strength and size of the recirculation. The non-dimesionalized pressure drop monotonically decreased with an increase in the Reynolds number. In general, the module average Nusselt number increases with an increase in the Reynolds number. The results at Pr = 7.0 indicate a significant increase in the computed module average Nusselt number when compared to those for Pr = 0.7. The overall performance of in-line configuration for lower height ratio (H/Da = 2) and higher length ratio (L/Da = 6) is preferable since it provides higher heat transfer rate for all Reynolds numbers except for the lowest Re value of 25. As expected the staggered configurations perform better than the in-line configuration from the heat transfer point of view.

The following report on ARC 696: Advanced Architectural Design Studio: Alley Flat Initiative, at the University of Texas at Austin in the Spring of 2010 taught by Prof. Louise Harpman and visiting Prof. Sarah Gamble asks how new knowledge is acquired through the in-depth study and reconstruction of documentary recordings taken from a semester of the studio. The recordings were made of the activities that transpired as a result of the educational studio design process, interactions with educators, reviewers, community partners, clients, professional architects, contractors, citizens and the unique sites that were chosen for consideration. The narrative of the studio was then reconstructed into the language of film and supervised by Anne Lewis of the Department of Radio Television and Film at the University of Texas. Through observation, I have recorded the process by which the Alley Flat Initiative attempts to create a unique educational experience for students by exposing them to real life actors in the creation of housing that is affordable, green and mitigates the forces of gentrification. In the recording process, I documented the initial design question posed to the studio, the formation of design partnerships between students, the collaborative engagement of students and clients, faculty and community reviews, stumbling blocks in the process, the negotiations between the concepts of affordability and sustainable design, interactions between the students and stakeholders, and student reflections on their experiences as participants in the Alley Flat Initiative studio. The focus of film is to create a body of research that is easily transmitted on the student’s ability to learn design through exposure to real clients, a real site and a chance that their design might be built. Further, the research seeks to make recommendations that can be implemented into the organizational language of future Alley Flat Studios in the School of Architecture at the University of Texas at Austin. This report will: (1) lay the groundwork for the methodology that was incorporated into the recording; (2) review existing literature on the subject of filmmaking as a means to conduct research; and (3) reveal the findings of the research and implications for future service learning projects. Therefore, the report will serve to contextualize elements of the research that were not able to be addressed by the film. / text

Film cooling is used in gas turbine engines to cool turbine components. Cooler air is bled from the compressor, routed internally through turbine vanes and blades, and exits through discrete holes, creating a film of coolant on the parts’ surfaces. Cooling the turbine components protects them from thermal damage and allows the engine to operate at higher combustion temperatures, which increases the engine efficiency. Shaped film cooling holes with diffuser exits have the advantage that they decelerate the coolant flow, enabling the coolant jets to remain attached to the surface at higher coolant flow rates. Furthermore, the expanded exits of the coolant holes provide a wider coolant distribution over the surface. The first part of this dissertation provides data for a new laidback, fan-shaped hole geometry designed at Pennsylvania State University’s Experimental and Computational Convection Laboratory. The shaped hole geometry was tested on flat plate facilities at the University of Texas at Austin and Pennsylvania State University. The objective of testing at two laboratories was to verify the adiabatic effectiveness performance of the shaped hole, with the intent of the data being a standard of comparison for future experimental and computational shaped hole studies. At first, measurements of adiabatic effectiveness did not match between the labs, and it was later found that shaped holes are extremely sensitive to machining, the material they are machined into, and coolant entrance effects. In addition, the adiabatic effectiveness was found to scale with velocity ratio for multiple density ratios and mainstream turbulence intensities. The second part of this dissertation measures heat transfer coefficient augmentation (hf/h0) at density ratios (DR) of 1.0, 1.2, and 1.5 using a uniform heat flux plate and the same shaped hole geometry. In the past, heat transfer coefficient augmentation was generally measured at DR = 1.0 under the assumption that hf/h0 was independent of density ratio. This dissertation is the first study to directly measure the wall and adiabatic wall temperature to calculate heat transfer coefficient augmentation at DR > 1.0. The results showed that the heat transfer coefficient augmentation was low while the jets were attached to the surface and increased when the jets started to separate. At DR = 1.0, hf/h0 was higher for a given blowing ratio than at DR = 1.2 and DR = 1.5. However, when velocity ratios are matched, better correspondence was found at the different density ratios. Surface contours of hf/h0 showed that the heat transfer was initially increased along the centerline of the jet, but was reduced along the centerline at distances farther downstream. The decrease along the centerline may be due to counter-rotating vortices sweeping warm air next to the heat flux plate toward the center of the jet, where they sweep upward and thicken the thermal boundary layer. This warming of the core of the coolant jet over the heated surface was confirmed with thermal field measurements. / text

Flat slab-column connections are common elements in reinforced concrete (RC) structures such as parking garages. In cold weather regions, these structures are exposed to de-icing salts and aggressive environments. Using fiber reinforced polymer (FRP) bars instead of steel in such structures will overcome the corrosion problems associated with steel reinforcement. However, the available literature shows few studies to evaluate the behaviour of FRP-RC interior slab-column connections tested mainly under concentric loads, which seldom occurs in a real building. The main objectives of this research are to deal with this gap by investigating the behaviour of full-scale glass (G) FRP-RC interior slab-column connections subjected to eccentric load and to provide design recommendations for such type of connections. This study consisted of two phases, experimental and analytical. The experimental phase included the construction and testing of ten full-scale interior slab-column connections. The parameters investigated in the experimental phase were flexural reinforcement ratio, concrete compressive strength, type of the reinforcement, moment-to-shear ratio and the spacing between the shear stud reinforcement. Test results revealed that increasing the GFRP reinforcement ratio or the concrete strength increased the connection capacity. Moreover, compared to the control steel-RC specimen, the GFRP-RC connection with similar reinforcement rigidity showed comparable capacity and deflection at failure. Also, increasing the moment-to-shear ratio resulted in a reduction in the vertical load capacity, while using the shear stud reinforcement enhanced the strength up to 23%. In the analytical phase, a 3-D finite element model (FEM) was constructed using specialized software. The constructed FEM was able to predict the experimental results within a reasonable accuracy. The verified FEM was then used to conduct a parametric study to evaluate the effects of perimeter-to-depth ratio, column aspect ratio, slab thickness and a wide range of flexural reinforcement ratio. The numerical results showed that increasing the reinforcement ratio increased the connection capacity. In addition, increasing the perimeter-to-depth ratio and slab thickness reduced the punching shear stresses at failure, while, the effect of the column rectangularity diminished for a ratio greater than three. Moreover, the results showed prominent agreement with the experimental results from literature. / October 2015

The central objective of this work is to present an analysis of the asymptotic conformal Killing vectors in asymptotically-flat space-times of general relativity. This problem has been examined by two different methods; in Chapter 5 the asymptotic expansion technique originated by Newman and Unti [31] leads to a solution for asymptotically-flat spacetimes which admit an asymptotically shear-free congruence of null geodesics, and in Chapter 6 the conformal rescaling technique of Penrose [54] is used both to support the findings of the previous chapter and to set out a procedure for solution in the general case. It is pointed out that Penrose's conformal technique is preferable to the use of asymptotic expansion methods, since it can be established in a rigorous manner without leading to the possible convergence difficulties associated with asymptotic expansions. Since the asymptotic conformal symmetry groups of asymptotically flat space-times Are generalisations of the conformal group of Minkowski space-time we devote Chapters 3 and 4 to a study of the flat space case so that the results of later chapters may receive an interpretation in terms of familiar concepts. These chapters fulfil a second, equally important, role in establishing local isomorphisms between the Minkowski-space conformal group, 90(2,4) and SU(2,2). The SO(2,4) representation has been used by Kastrup [61] to give a physical interpretation using space-time gauge transformations. This appears as part of the survey of interpretative work in Chapter 7. The SU(2,2) representation of the conformal group has assumed a theoretical prominence in recent years. through the work of Penrose [9-11] on twistors. In Chapter 4 we establish contact with twistor ideas by showing that points in Minkowski space-time correspond to certain complex skew-symmetric rank two tensors on the SU(2,2) carrier space. These objects are, in Penrose's terminology [91, simple skew-symmetric twistors of valence [J. A particularly interesting aspect of conformal objects in space-time is explored in Chapter 8, where we extend the work of Geroch [16] on multipole moments of the Laplace equation in 3-space to the consideration. of Q tý =0 in Minkowski space-time. This development hinges upon the fact that multipole moment fields are also conformal Killing tensors. In the final chapter some elementary applications of the results of Chapters 3 and 5 are made to cosmological models which have conformal flatness or asymptotic conformal flatness. In the first class here we have 'models of the Robertson-Walker type and in the second class we have the asymptotically-Friedmann universes considered by Hawking [73].

This thesis is a study of three categories of problems in fermionic systems for which topology plays an important role: (i) The properties of zero modes arising in systems of fermions interacting with a bosonic background, with a special focus on Majorana modes arising in the superconductor state. We propose a method for counting Majorana modes and we study a mechanism for controlling their number parity in lattice systems, two questions that are of relevance to the protection of quantum bits. (ii) The study of dispersionless bands in two dimensions as a platform for correlated physics, where it is shown the possibility of stabilizing the fractional quantum Hall effect in a flat band with Chern number. (iii) The extension of the hierarchy of quantum Hall fluids to the case of time-reversal symmetric incompressible ground states describing a phase of strongly interacting topological insulators in two dimensions. / Physics

Water scarcity is among the most serious, long-term challenges in the world. To an ever increasing degree, sustainable water supply depends on the utilization of water of impaired initial quality. This is particularly true in developing nations and in water-stressed areas such as the American Southwest. Water of impaired quality could be water of high salinity such as brackish groundwater. Traditionally, reverse osmosis (RO) would be chosen to desalinate the brackish groundwater, since RO costs are competitive with those of thermal desalination, even for seawater applications. However, both conventional thermal distillation and RO are energy intensive, complex processes that discourage decentralized or rural implementation. In addition, both technologies require enhanced expertise for operation and maintenance, and are susceptible to scaling and fouling unless extensive feed pretreatment is employed. Membrane distillation (MD), driven by vapor pressure gradients, can potentially overcome many of these drawbacks. MD can operate using low-grade, sub-boiling temperature heat sources. When it is driven by solar energy it does not require highly concentrating collection devices, non-aqueous working fluids, or complex temperature control systems, nor does it require extensive operational expertise. Membrane Distillation (MD) applications, background and modeling efforts are discussed in the first part of this dissertation. Two main studies are presented in this document: Firstly, Sweeping Gas Membrane Distillation (SGMD) through a hollow fiber membrane was studied both experimentally and modeled mathematically to describe performance of SGMD and extend results to predict membrane module efficiency and secondly, SGMD through a flat sheet MD module to study the effect of membrane characteristics in combination with operational variables. A final study was conducted to examine the effect of mesh spacer insertion in flat sheet membrane module on the permeate water production.