Titanium (Ti) alloys have been commonly used in the aerospace industry, not only because they have a high strength-to-weight ratio (comparing to the steels) but also their satisfactory corrosion resistance. Furthermore, they can be assembled with the carbon fibre composite parts. However, conventional manufacturing methods cause high material scrap rate and require lots of machining to obtain the final shape and size, which increases both the manufacturing time and cost. In order to improve the efficiency and reduce the cost of Ti parts, Additive Manufacturing (AM) has been developed. Rolled Wire and Arc Additive Manufacturing (rolled WAAM) is one of the AM processes. The main characteristics of this technology is the reduced β grain size to refine the alloy's microstructure. Both the ultimate tensile strength and yield strength of Ti alloy made by rolled WAAM are at least 10% higher than traditional wrought Ti. This project is to investigate the fatigue crack growth rates of the Ti-6Al-4V built by rolled WAAM process in both the longitudinal and transverse orientations to study the effect of rolling on fatigue crack growth rate of WAAM processed Ti. The project was carried out by testing the fatigue crack growth rates for 4 compact tension specimens. The test results of different orientations were compared with each other, and scatters in fatigue life and fatigue crack growth rate were found. Fatigue crack growth rate is lower in the longitudinal specimens. The results are also compared with those of the unrolled WAAM specimens tested in a previous project. It was found that rolling can significantly improve the fatigue crack growth behaviour in WAAM processed Ti, and can reduce the difference between the two orientations, i.e. achieving better isotropic material properties. Recorded scatters may be caused by the process induced residual stresses, error in measurement, and the test machine load range being much higher than the applied loads. More specimens can be tested to validate above observations further.

This thesis investigates fatigue crack growth rate behavior in the threshold and near-threshold regimes for a Ti-6Al-4V (STOA) alloy using two proposed ASTM procedures- (1) load-shedding (LS) using a larger load-shed rate than the current ASTM Standard E647 load-reduction (LR) test procedure, and (2) compression pre-cracking constant-amplitude (CPCA) or load-increasing (CPLI) and load-shedding (CPLS). Tests were conducted at a low stress ratio (R = 0.1) on compact C(T) specimens of two different widths (W = 51 and 76 mm) and threshold fatigue crack growth rates were generated. These test data were compared to previous test data produced from the same batch of material using the current LR and the CPCA test procedure. While no test procedure provided an exact representation of the threshold value (?Kth), the compression pre-cracking (CP) procedures were the most promising. The LR, LS, and CPLS test procedures were influenced by prior loading-history and various crack-closure mechanisms, leading to higher ?Kth values and slower crack growths in the threshold regime. The LS tests (at shed-rates of -0.08,-0.32, and -0.95 mm-1) generated ?Kth values that were 15% to 32% higher than the estimated threshold stress-intensity factor range (?*Kth)R=0.1. The CP test procedures are a more accurate alternative for developing near-threshold and threshold fatigue crack growth rates. The CPLS test procedure produced a ?Kth value that was 10% higher than (?*Kth)R=0.1. LR and LS tests produced different ?Kth values as a function of the specimen width for the given load ratio. The CP test procedures produced consistent crack growth rates over the same range of ?K values examined, independent of the specimen width. Further research is required for developing test procedure(s) capable of providing a more definitive representation of the ?Kth value and closureree fatigue crack growth rates in the threshold regime.

No description available.

Fatigue crack growth behavior of AA7050 T7451 aluminum alloy under mode II loading condition in two orientations was investigated. Compact shear specimens were prepared in TL and LT directions. A loading frame for mode II type of loading was manufactured. Using the loading frame and the specimen, KIIC values and mode II fatigue crack growth rates were calculated. Fractographic analysis of the fracture surfaces of both mode II fracture toughness test specimens and mode II fatigue crack growth test specimens were done to examine the effects of mode II load. KIIC values were measured between 1.3 and 1.5 times the KIC values for this alloy. As for mode II fatigue crack growth rates, TL orientation shows the highest mode II fatigue crack growth resistance.

The effect of different aging treatments on fatigue crack growth behavior of AA6013 aluminum alloy was investigated. C(T) (Compact Tension) specimens were prepared in L-T and T-L direction for fatigue crack growth tests. Samples were in T651 as received, T42 which is solution heat treated at 538 &ordm / C for 90 minutes, water quenched and aged in room temperature for 96 hours, and one group of samples were overaged at 245 &ordm / C for 12 hours after T42 condition was achieved. Hardness and conductivity measurements were achieved for all conditions after the heat treatments. Fatigue crack growth tests were performed at as received condition T651, T42 and 245 &ordm / C aged samples in laboratory air with sinusoidal loading of stress ratio R=0.1 and at a frequency of 1 Hz. The highest fatigue crack growth resistance is observed for T651 T-L and 245 &ordm / C overaged L-T condition.

The main objective of the project was to establish a fracture-mechanics energy-based approach for the design of structural adhesive joints under cyclic loading. This required understanding how an adhesive system behaved near its fatigue threshold, and how the key factors affected this behavior in a fresh undegraded joint. The investigated factors were mode ratio (phase angle), substrate material, surface treatment and surface roughness (both affecting the bond strength), bondline thickness and load ratio. It was first required to understand how the adhesive system behaved under quasi-static loading by examining a fracture mechanics-based design approach for adhesive systems with different substrate materials and geometries. Experiments were initially performed to characterize the strength of aluminum and steel adhesive systems based on the fracture envelope, critical strain energy release rate as a function of the mode ratio. Ultimate failure loads of aluminum and steel adhesive joints, having different overlap end conditions and different geometries were then experimentally measured. These values were compared with the failure loads extracted from the fracture envelope. Considering the toughening behavior of the adhesive in the fracture mechanics analyses, a very good agreement (average of 6%) was achieved between the predictions and experiments for all types of overlap end conditions and geometries. Different fatigue threshold testing approaches, which are commonly used in the literature or suggested by the ASTM standard, were evaluated for the cracked and intact fillet joints. Based on the experimental and analytical studies, the most appropriate technique for fatigue testing and characterization of adhesive systems was suggested. Comparing the mixed-mode near-threshold behavior of different adhesive systems with the fracture behavior and fatigue mode-I and mixed-mode high crack growth rates showed the high sensitivity of the mixed-mode near-threshold fatigue to the subtle changes in the interfacial bond strength. In order to make a baseline for the design of adhesive joints under cyclic loading, similar to the previous fracture tests and following the energy-based approach, fatigue behavior was characterized as a function of the loading mode ratio for aluminum and steel adhesive joints. The effect of substrate material, surface treatment, bondline thickness, surface roughness and fatigue testing load ratio on the near-threshold fatigue behavior of adhesives joints was evaluated experimentally. The experimental observations were then explained using finite element modeling. To generalize the conclusions, the majority of experiments and studies covered a broad range of crack growth rates, as low as fatigue threshold and as high as 10-2 mm/cycle. Having understood the significant testing and design parameters, an adhesive system can be designed based on a safe cyclic load that produces an insignificant (for automotive industry) or reasonably low but known crack growth rate (for aerospace industry).

The mechanical behavior of a high pressure die cast AM60B Mg alloy is studied. Constant load amplitude fatigue tests were conducted at room, elevated and cold temperatures, with a stress ratio of R=0.1, and frequency of 30 Hz. The objective was to identify the possible effects of temperature on fatigue life cycle. In addition, fatigue crack propagation tests were conducted to ascertain the fatigue response of the alloy and determine its fatigue crack growth rate as a function of the applied stress ratio, experimentally, analytically and computationally, using Walker’s model. The results demonstrated that temperature had a significant influence on the fatigue life, and that the life increased at cold temperature but decreased at elevated temperature as compared to that evaluated at room temperature. In this study, the limit for applicability of LEFM was established for AM60B magnesium alloy. In addition, fatigue crack propagation test results were used to evaluate the coefficients of the Paris model.

The main objective of the project was to establish a fracture-mechanics energy-based approach for the design of structural adhesive joints under cyclic loading. This required understanding how an adhesive system behaved near its fatigue threshold, and how the key factors affected this behavior in a fresh undegraded joint. The investigated factors were mode ratio (phase angle), substrate material, surface treatment and surface roughness (both affecting the bond strength), bondline thickness and load ratio. It was first required to understand how the adhesive system behaved under quasi-static loading by examining a fracture mechanics-based design approach for adhesive systems with different substrate materials and geometries. Experiments were initially performed to characterize the strength of aluminum and steel adhesive systems based on the fracture envelope, critical strain energy release rate as a function of the mode ratio. Ultimate failure loads of aluminum and steel adhesive joints, having different overlap end conditions and different geometries were then experimentally measured. These values were compared with the failure loads extracted from the fracture envelope. Considering the toughening behavior of the adhesive in the fracture mechanics analyses, a very good agreement (average of 6%) was achieved between the predictions and experiments for all types of overlap end conditions and geometries. Different fatigue threshold testing approaches, which are commonly used in the literature or suggested by the ASTM standard, were evaluated for the cracked and intact fillet joints. Based on the experimental and analytical studies, the most appropriate technique for fatigue testing and characterization of adhesive systems was suggested. Comparing the mixed-mode near-threshold behavior of different adhesive systems with the fracture behavior and fatigue mode-I and mixed-mode high crack growth rates showed the high sensitivity of the mixed-mode near-threshold fatigue to the subtle changes in the interfacial bond strength. In order to make a baseline for the design of adhesive joints under cyclic loading, similar to the previous fracture tests and following the energy-based approach, fatigue behavior was characterized as a function of the loading mode ratio for aluminum and steel adhesive joints. The effect of substrate material, surface treatment, bondline thickness, surface roughness and fatigue testing load ratio on the near-threshold fatigue behavior of adhesives joints was evaluated experimentally. The experimental observations were then explained using finite element modeling. To generalize the conclusions, the majority of experiments and studies covered a broad range of crack growth rates, as low as fatigue threshold and as high as 10-2 mm/cycle. Having understood the significant testing and design parameters, an adhesive system can be designed based on a safe cyclic load that produces an insignificant (for automotive industry) or reasonably low but known crack growth rate (for aerospace industry).

The effect of retrogression and reaging heat treatment on corrosion fatigue crack growth behavior on AA7050 T73651 aluminum alloy is investigated. CT (Compact Tension) specimens are prepared in LS direction for fatigue crack growth tests . Samples are solution heat treated at 477 &deg / C and aged at 120 &deg / C for 24 h (T6 condition). After that, samples are retrogressed at 200 &deg / C for times of 1, 5, 30, 55 and 80 minutes in a circulating oil bath. Then, samples are re-aged at 120 &deg / C for 24 h (T6 condition). Hardness measurements are taken at different retrogression times and at the end of the heat treatment. Fatigue crack growth tests are performed at as received condition and at different retrogression times with sinusoidal loading of R=0.1 and f=1 in both laboratory air and corrosive environment of 3.5% NaCl solution. The highest fatigue crack growth resistance is observed for 30 min. and 5 min. retrogression for laboratory air and corrosive environment respectively. It is concluded that RRA can successfully be used to improve fatigue performance of this alloy.

The main subject of this master’s thesis was to evalute inluence of loading cycle asymmetry and long-term thermal exposure on fatigue crack growth rate in martensitic P91 and P92 steels. Experiments were carried out in Material and metallurgical research Ostrava Ltd. and their main aim was to study the influences of different loading cycle asymmetries (R = 0,1 and R = 0,6) as well as 5000 hours/600 °C (P91) respectively 5000 hours/650 °C (P92) of thermal exposure on fatigue crack growth rate.