Near surface structures across the Brevard fault zone are studied using the refraction and reflection arrivals recovered from the Appalachian Ultradeep Core Hole (ADCOH) regional seismic Line 1. In using refracted arrivals, a new processing approach is introduced that translates refracted first arrivals from multifold seismic data into a refraction stack of two-way delay time sections. Reprocessing of reflected arrivals has improved shallow reflectors and allowed better imaging of the Brevard fault zone. Following processing of refraction and reflection arrivals independently, both data sets are combined into a <u>composite stack</u> section. The composite stack section displays one bright refractor interpreted as the boundary between the weathered layer and high velocity crystalline rocks. This refractor is continuous in the Inner Piedmont with occasional vertical offsets. The continuity of the refractor diminishes across the Brevard fault zone. In the eastern Blue Ridge, the refractor is discontinuous with high angle truncations. On the composite stack section, the Brevard fault zone can be traced from the surface to 6 km (2 s) where it appears to splay from the Blue Ridge thrust. Different from previous interpretations, the Brevard fault zone is imaged as having both an upper and a lower boundary surface as well as a group of reflectors within the zone. This reflection package initially thickens to 2 km at 3 km depth, then thins as it reaches the Blue Ridge master decollement. The Blue Ridge thrust is as shallow as 1.5 km (0.5 s) at the northwest end of the Line l. A deeper decollement is interpreted below the Blue Ridge thrust. The depth of this deeper thrust is 3 km (1 s) at the northwest end of the line, and also joins to the Blue Ridge thrust at 6 km depth making the structures below the Brevard fault zone more complex than previously published. / Master of Science

Untersuchungen zur internen Architektur von großen Störungszonen beschränken sich üblicherweise auf die, an der Erdoberfläche aufgeschlossene, störungsbezogene Deformation. Eine Methode, die es ermöglicht, Informationen über die Tiefenfortsetzung einer Störung zu erhalten, ist die Abbildung der elektrischen Leitfähigkeit des Untergrundes.<br /> <br /> Die vorliegende Arbeit beschäftigt sich mit der kombinierten strukturgeologischen und magnetotellurischen Untersuchung eines Segmentes der 'West Fault'-Störung in den nordchilenischen Anden. Die West Fault ist ein Abschnitt des über 2000 km langen Präkordilleren-Störungssystem, welches im Zusammenhang mit der Subduktion vor der südamerikanischen Westküste entstanden ist. Die Aktivität dieses Störungssystems reichte vom Eozän bis in das Quartär. Der Verlauf der West Fault ist im Untersuchungsgebiet (22&#176;04'S, 68&#176;53'W) an der Oberfläche klar definiert und weist über viele zehner Kilometer eine konstante Streichrichtung auf. Die Aufschlussbedingungen und die Morphologie des Arbeitsgebietes sind ideal für kombinierte Untersuchungen der störungsbezogenen Deformation und der elektrischen Leitfähigkeit des Untergrundes mit Hilfe magnetotellurischer Experimente (MT) und der erdmagnetischen Tiefensondierung (GDS). Ziel der Untersuchungen war es, eine mögliche Korrelation der beiden Meßmethoden herauszuarbeiten, und die interne Störungsarchitektur der West Fault umfassend zu beschreiben.<br /> <br /> Die Interpretation von Sprödbruch-Strukturen (kleinmaßstäbliche Störungen sowie Störungsflächen mit/ohne Bewegungslineationen) im Untersuchungsgebiet weist auf überwiegend seitenverschiebende Deformation entlang von subvertikal orientierten Scherflächen hin. Dextrale und sinistrale Bewegungsrichtungen können innerhalb der Störungszone bestätigt werden, was auf Reaktivierungen des Störungssystems schliessen läßt. Die jüngsten Deformationen im Arbeitsgebiet haben dehnenden Charakter, wobei die kinematische Analyse eine unterschiedliche Orientierung der Extensionsrichtung beiderseits der Störung andeutet. Die Bruchflächendichte nimmt mit Annäherung an die Störung zu und zeichnet einen etwa 1000 m breiten Bereich erhöhter Deformationsintensität um die Störungsspur aus (damage zone). Im Zentrum dieser Zone weist das Gestein eine intensive Alteration und Brekzierung auf, die sich über eine Breite von etwa 400 m erstreckt. Kleine Störungen und Scherflächen in diesem zentralen Abschnitt der Störung fallen überwiegend steil nach Osten ein (70-80&#176;).<br /> <br /> Innerhalb desselben Arbeitsgebietes wurde ein 4 km langes MT/GDS Profil vermessen, welches senkrecht zum Streichen der West Fault verläuft. Für die zentralen 2 km dieses Hauptprofils beträgt der Abstand der Meßstationen jeweils 100 m. Ein weiteres Profil, bestehend aus 9 Stationen mit einem Abstand von 300 m zueinander, quert die Störung einige Kilometer entfernt vom eigentlichen Arbeitsgebiet. Die Aufzeichnung der Daten erfolgte mit vier S.P.A.M MkIII Apparaturen in einem Frequenzbereich von 1000 Hz bis 0.001 Hz.<br /> <br /> In den GDS Daten beider Profile ist die Störung für Frequenzen >1 Hz deutlich abgebildet: Die Induktionspfeile kennzeichnen eine mehrere hundert Meter breite Zone erhöhter Leitfähigkeit, welche sich entlang der West Fault erstreckt. Die Dimensionalitätsanalyse der MT Daten rechtfertigt die Anpassung der gemessenen Daten mit einem zwei-dimensionalen Modell für einen Frequenzbereich von 1000 Hz bis 0.1 Hz. In diesem Frequenzbereich, der eine Auflösung der Leitfähigkeitsstruktur bis mindestens 5 km Tiefe ermöglicht, läßt sich eine regionale geoelektrische Streichrichtung parallel zum Verlauf der West Fault nachweisen.<br /> <br /> Die Modellierung der MT Daten beruht auf einem Inversionsalgorithmus von Mackie et al. (1997). Leitfähigkeitsanomalien, die sich aus der Inversions-Modellierung ergeben, werden anhand von empirischen Sensitivitätsstudien auf ihre Robustheit überprüft. Dabei werden die Eigenschaften (Geometrie, Leitfähigkeit) der Strukturen systematisch variiert und sowohl Vorwärts- als auch Inversionsrechnungen der modifizierten Modelle durchgeführt. Die jeweiligen Modellergebnisse werden auf ihre Konsistenz mit dem Ausgangsdatensatz überprüft. Entlang beider MT Profile wird ein guter elektrischer Leiter im zentralen Abschnitt der West Fault aufgelöst, wobei die Bereiche erhöhter Leitfähigkeit östlich der Störungsspur liegen. Für das dicht vermessene MT Profil ergibt sich eine Breite des Störungsleiters von etwa 300 m sowie ein steiles Einfallen der Anomalie nach Osten (70&#176;). Der Störungsleiter reicht bis in eine Tiefe von mindestens 1100 m, während die Modellierungsstudien auf eine maximale Tiefenerstreckung <2000 m hinweisen. Das Profil zeigt weitere leitfähige Anomalien, deren Geometrie aber weniger genau aufgelöst ist.<br /> <br /> Die Störungsleiter der beiden MT Profile stimmen in ihrer Position mit der Alterationszone überein. Im zentralen Bereich des Hauptprofils korreliert darüber hinaus das Einfallen der Sprödbruch-Strukturen und der Leitfähigkeitsanomalie. Dies weist darauf hin, daß die Erhöhung der Leitfähigkeit im Zusammenhang mit einem Netzwerk von Bruchstrukturen steht, welches mögliche Wegsamkeiten für Fluide bietet. Der miteinander in Verbindung stehende Gesteins-Porenraum, der benötigt wird, um die gemessene Erhöhung der Leitfähigkeit durch Fluide im Gestein zu erklären, kann anhand der Salinität einiger Grundwasserproben abgeschätzt werden (Archies Gesetz). Wasserproben aus größerer Tiefe, weisen aufgrund intensiverer Fluid-Gesteins-Wechselwirkung eine höhere Salinität, und damit eine verbesserte Leitfähigkeit, auf. Für eine Probe aus einer Tiefe von 200 m ergibt sich demnach eine benötigte Porosität im Bereich von 0.8% - 4%. Dies legt nahe, daß Wässer, die von der Oberfläche in die Bruchzone der Störung eindringen, ausreichen, um die beobachtete Leitfähigkeitserhöhung zu erklären. Diese Deutung wird von der geochemischen Signatur von Gesteinsproben aus dem Alterationsbereich bestätigt, wonach die Alteration in einem Regime niedriger Temperatur (<95&#176;C) stattfand. Der Einfluß von aufsteigenden Tiefenwässern wurde hier nicht nachgewiesen. Die geringe Tiefenerstreckung des Störungsleiters geht wahrscheinlich auf Verheilungs- und Zementationsprozesse der Bruchstrukturen zurück, die aufgrund der Lösung und Fällung von Mineralen in größerer Tiefe, und damit bei erhöhter Temperatur, aktiv sind.<br /> <br /> Der Vergleich der Untersuchungsergebnisse der zur Zeit seismisch inaktiven West Fault mit veröffentlichten Studien zur elektrischen Leitfähigkeitsstruktur der aktiven San Andreas Störung, deutet darauf hin, daß die Tiefenerstreckung und die Leitfähigkeit von Störungsleitern eine Funktion der Störungsaktivität ist. Befindet sich eine Störung in einem Stadium der Deformation, so bleibt das Bruchnetzwerk für Fluide permeabel und verhindert die Versiegelung desselben. / The characterisation of the internal architecture of large-scale fault zones is usually restricted to the outcrop-based investigation of fault-related structural damage on the Earth's surface. A method to obtain information on the downward continuation of a fault is to image the subsurface electrical conductivity structure.<br /> <br /> This work deals with such a combined investigation of a segment of the West Fault, which itself is a part of the more than 2000 km long trench-linked Precordilleran Fault System in the northern Chilean Andes. Activity on the fault system lasted from Eocene to Quaternary times. In the working area (22&#176;04'S, 68&#176;53'W), the West Fault exhibits a clearly defined surface trace with a constant strike over many tens of kilometers. Outcrop condition and morphology of the study area allow ideally for a combination of structural geology investigation and magnetotelluric (MT) / geomagnetic depth sounding (GDS) experiments. The aim was to achieve an understanding of the correlation of the two methods and to obtain a comprehensive view of the West Fault's internal architecture.<br /> <br /> Fault-related brittle damage elements (minor faults and slip-surfaces with or without striation) record prevalent strike-slip deformation on subvertically oriented shear planes. Dextral and sinistral slip events occurred within the fault zone and indicate reactivation of the fault system. Youngest deformation increments mapped in the working area are extensional and the findings suggest a different orientation of the extension axes on either side of the fault. Damage element density increases with approach to the fault trace and marks an approximately 1000 m wide damage zone around the fault. A region of profound alteration and comminution of rocks, about 400 m wide, is centered in the damage zone. Damage elements in this central part are predominantly dipping steeply towards the east (70-80&#176;).<br /> <br /> Within the same study area, the electrical conductivity image of the subsurface was measured along a 4 km long MT/GDS profile. This main profile trends perpendicular to the West Fault trace. The MT stations of the central 2 km were 100 m apart from each other. A second profile with 300 m site spacing and 9 recording sites crosses the fault a few kilometers away from the main study area. Data were recorded in the frequency range from 1000 Hz to 0.001 Hz with four real time instruments S.P.A.M. MkIII.<br /> <br /> The GDS data reveal the fault zone for both profiles at frequencies above 1 Hz. Induction arrows indicate a zone of enhanced conductivity several hundred meters wide, that aligns along the WF strike and lies mainly on the eastern side of the surface trace. A dimensionality analysis of the MT data justifies a two dimensional model approximation of the data for the frequency range from 1000 Hz to 0.1 Hz. For this frequency range a regional geoelectric strike parallel to the West Fault trace could be recovered. The data subset allows for a resolution of the conductivity structure of the uppermost crust down to at least 5 km.<br /> <br /> Modelling of the MT data is based on an inversion algorithm developed by Mackie et al. (1997). The features of the resulting resistivity models are tested for their robustness using empirical sensitivity studies. This involves variation of the properties (geometry, conductivity) of the anomalies, the subsequent calculation of forward or constrained inversion models and check for consistency of the obtained model results with the data. A fault zone conductor is resolved on both MT profiles. The zones of enhanced conductivity are located to the east of the West Fault surface trace. On the dense MT profile, the conductive zone is confined to a width of about 300 m and the anomaly exhibits a steep dip towards the east (about 70&#176;). Modelling implies that the conductivity increase reaches to a depth of at least 1100 m and indicates a depth extent of less than 2000 m. Further conductive features are imaged but their geometry is less well constrained.<br /> <br /> The fault zone conductors of both MT profiles coincide in position with the alteration zone. For the dense profile, the dip of the conductive anomaly and the dip of the damage elements of the central part of the fault zone correlate. This suggests that the electrical conductivity enhancement is causally related to a mesh of minor faults and fractures, which is a likely pathway for fluids. The interconnected rock-porosity that is necessary to explain the observed conductivity enhancement by means of fluids is estimated on the basis of the salinity of several ground water samples (Archie's Law). The deeper the source of the water sample, the more saline it is due to longer exposure to fluid-rock interaction and the lower is the fluid's resistivity. A rock porosity in the range of 0.8% - 4% would be required at a depth of 200 m. That indicates that fluids penetrating the damaged fault zone from close to the surface are sufficient to explain the conductivity anomalies. This is as well supported by the preserved geochemical signature of rock samples in the alteration zone. Late stage alteration processes were active in a low temperature regime (<95&#176;C) and the involvement of ascending brines from greater depth is not indicated. The limited depth extent of the fault zone conductors is a likely result of sealing and cementation of the fault fracture mesh due to dissolution and precipitation of minerals at greater depth and increased temperature.<br /> <br /> Comparison of the results of the apparently inactive West Fault with published studies on the electrical conductivity structure of the currently active San Andreas Fault, suggests that the depth extent and conductivity of the fault zone conductor may be correlated to fault activity. Ongoing deformation will keep the fault/fracture mesh permeable for fluids and impede cementation and sealing of fluid pathways.

A basin analysis was conducted at the Conway Flat coast (Marlborough Fault Zone, South Island, New Zealand) to investigate the interaction of regional and local structure in a transpressional plate boundary and its control on basin formation. A multi-tiered approach has been employed involving: (i) detailed analysis of sedimentary deposits; (ii) geomorphic mapping of terraces, fault traces and lineaments; (iii) dating of deposits by 14C and OSL and (iv) the integration of data to form a basin-synthesis in a sequence stratigraphy framework. A complex thrust fault zone (the Hawkswood Thrust Fault Zone), originating at the hinge of the thrust-cored Hawkswood anticline, is interpreted to be a result of west-dipping thrust faults joining at depth with the Hundalee Fault and propagating eastwards. The faults uplift and dissect alluvial fans to form terraces along the Conway Flat coast that provide the necessary relief to form the fan deltas. These terrace/fan surfaces are ~9 km long and ~3 km wide, composite features, with their upper parts representing sub-aerial alluvial fans. These grade into delta plains of Quaternary Gilbert-style fan deltas. Uplift and incision have created excellent 3D views of the underlying Gilbert-style fan delta complexes from topsets to prodelta deposits. Erosive contacts between the Medina, Rafa, Ngaroma and modern Conway fan delta deposits, coupled with changes in terrace elevations allow an understanding of the development of multiple inset terraces along the Conway Flat coast. These terraces are divided into five stages of evolution based on variations in sedimentary facies and geomorphic mapping: Stage I involves the uplift of the Hawkswood Range and subsequent increased sedimentation rate such that alluvial fans prograded to the sea to form the Medina fan delta Terrace. Stage II began with a period of incision, from lowering sea level or changes in the uplift and sedimentation rate and continued with the deposition of the Dawn and Upham fan deltas. Stage III starts with the incision of the Rafa Terrace and deposition of aggradational terraces in the upper reaches. Stage IV initiated by a period of incision followed by deposition of estuarine facies at ~8ka and Stage V began with a period of incision and continues today with the infilling of the incised valley by the modern fan delta of the Conway River and its continued progradation. New dates from within the Gilbert-type fan deltas along the Conway Flat coast are presented, using OSL and 14C dating techniques. Faulting at the Conway Flat coast began ~ 94 ka, based on the development of the Medina Terrace fan delta with uplift rates ~1.38~1.42 m/ka. The interplay of tectonics and sea level fluctuations continued as the ~79 ka Rafa Terrace fan deltas were created, with uplift rates calculated at ~1.39 m/ka. Detailed 14C ages from paleoforest (~8.4-~6.4 ka) in the Ngaroma Terrace and from the mouths of smaller streams have established uplift rates during the Holocene ~1-3 m/ka, depending on sea level.

Bulk rock strength is greatly dependent on fracture density, so that reductions in rock strength associated with faulting and fracturing should be reflected by reduced shear coupling and hence S-wave velocity. This study is carried out along the Canterbury rangefront and in Otago. Both lie within the broader plate boundary deformation zone in the South Island of New Zealand. Therefore built structures are often, , located in areas where there are undetected or poorly defined faults with associated rock strength reduction. Where structures are sited near to, or across, such faults or fault-zones, they may sustain both shaking and ground deformation damage during an earthquake. Within this zone, management of seismic hazards needs to be based on accurate identification of the potential fault damage zone including the likely width of off-plane deformation. Lateral S-wave velocity variability provides one method of imaging and locating damage zones and off-plane deformation. This research demonstrates the utility of Multi-Channel Analysis of Surface Waves (MASW) to aid land-use planning in such fault-prone settings. Fundamentally, MASW uses surface wave dispersive characteristics to model a near surface profile of S-wave velocity variability as a proxy for bulk rock strength. The technique can aid fault-zone planning not only by locating and defining the extent of fault-zones, but also by defining within-zone variability that is readily correlated with measurable rock properties applicable to both foundation design and the distribution of surface deformation. The calibration sites presented here have well defined field relationships and known fault-zone exposure close to potential MASW survey sites. They were selected to represent a range of progressively softer lithologies from intact and fractured Torlesse Group basement hard rock (Dalethorpe) through softer Tertiary cover sediments (Boby’s Creek) and Quaternary gravels. This facilitated initial calibration of fracture intensity at a high-velocity-contrast site followed by exploration of the limits of shear zone resolution at lower velocity contrasts. Site models were constructed in AutoCAD in order to demonstrate spatial correlations between S-wave velocity and fault zone features. Site geology was incorporated in the models, along with geomorphology, river profiles, scanline locations and crosshole velocity measurement locations. Spatial data were recorded using a total-station survey. The interpreted MASW survey results are presented as two dimensional snapshot cross-sections of the three dimensional calibration-site models. These show strong correlations between MASW survey velocities and site geology, geomorphology, fluvial profiles and geotechnical parameters and observations. Correlations are particularly pronounced where high velocity contrasts exist, whilst weaker correlations are demonstrated in softer lithologies. Geomorphic correlations suggest that off-plane deformation can be imaged and interpreted in the presence of suitable topographic survey data. A promising new approach to in situ and laboratory soft-rock material and mass characterisation is also presented using a Ramset nail gun. Geotechnical investigations typically involve outcrop and laboratory scale determination of rock mass and material properties such as fracture density and unconfined compressive strength (UCS). This multi-scale approach is espoused by this study, with geotechnical and S-wave velocity data presented at multiple scales, from survey scale sonic velocity measurements, through outcrop scale scanline and crosshole sonic velocity measurements to laboratory scale property determination and sonic velocity measurements. S-wave velocities invariably increased with decreasing scale. These scaling relationships and strategies for dealing with them are investigated and presented. Finally, the MASW technique is applied to a concealed fault on the Taieri Ridge in Macraes Flat, Central Otago. Here, high velocity Otago Schist is faulted against low velocity sheared Tertiary and Quaternary sediments. This site highlights the structural sensitivity of the technique by apparently constraining the location of the principal fault, which had been ambiguous after standard processing of the seismic reflection data. Processing of the Taieri Ridge dataset has further led to the proposal of a novel surface wave imaging technique termed Swept Frequency Imaging (SFI). This inchoate technique apparently images the detailed structure of the fault-zone, and is in agreement with the conventionally-determined fault location and an existing partial trench. Overall, the results are promising and are expected to be supported by further trenching in the near future.

The study of deformation zones is of great geological interest since these zones can separate rocks with different characteristics. The geometry of these structures with depth is important for interpreting the geological history of an area. Paper I to III present 2D reflection seismic data over deformation zones targeting structures in the upper 3-4 km of the crust. These seismic profiles were acquired with a crooked-line recording geometry. 2D seismic processing assumes a straight recording geometry. Most seismic processing tools were developed for sub-horizontally layered structures. However, in the crystalline rocks in Scandinavia more complex structures with contrasting dip directions and folding are common. The crooked-line recording geometries have the benefit of sampling a 3D volume. This broader sampling can be used to gain knowledge about the true geometry of subsurface structures. Correlation with geological maps and other geophysical data along with seismic data modeling can be used to differentiate reflections from faults or fracture zones from other reflectivity, e.g. mafic bodies. Fault and fracture zones may have a large impedance contrast to surrounding rocks, while ductile shear zones usually do not. The ductile shear zones can instead be interpreted based on differing reflectivity patterns between domains and correlations with geology or magnetic maps. Paper IV presents 3D reflection seismic data from a quick-clay landslide site in southern Sweden. The area is located in a deformation zone and structures in unconsolidated sediments may have been influenced by faults in the bedrock. The main target layer is located at only 20 m depth, but good surface conditions during acquisition and careful processing enabled a clear seismic image of this shallow layer to be obtained.The research presented in this thesis provides increased knowledge about subsurface structures in four geologically important areas. The unconventional processing methods used are recommended to future researchers working with data from crooked-line recording geometries in crystalline environments. The imaging of shallow structures at the quick-clay landslide site shows that the 3D reflection seismic method can be used as a complement to other geophysical measurements for shallow landslide site investigations.

Geologic storage of anthropogenic carbon dioxide (CO2) by injection into underground porous sandstone reservoirs has been proposed as a method for the reduction of anthropogenic greenhouse gas emissions. Upwards migration and leakage of injected fluids along natural fault and fracture networks is a key risk factor for potential injection locations. We examine exposed natural analogs to evaluate the impacts of faulting and fracturing on reservoir and top-seal pairs and to evaluate evidence for paleomigration of fluids along the fault zone. We examine the Iron Wash fault, a 25-km long normal fault which cuts Jurassic sedimentary rocks and has throws that range from 20-120 m, to examine how a fault may affect seal integrity. Field mapping, kinematic analysis, petrographic analysis, characterization of the fault zone facies and fault architecture, analysis of altered and mineralized rocks in and around the fault zone, and modeling of fault seal capacity was conducted to provide an understanding of the Iron Wash fault zone. Field data and observations were combined with well log and borehole data to produce three types of models for the Iron Wash fault: 1) geometric model of the fault in the subsurface, 2) predictive models of fault zone behavior and fault seal analysis, and 3) predictive geomechanical models of the response of the fault zone to an imposed stress field and increasing the effective stress on the fault. We conclude that the Iron Wash fault zone has low sealing capacity and will likely not behave as a seal for fluids against the fault zone due primarily to modest throw on the fault and high frequency of fractures associated with the fault zone. Analysis of fluid alteration and mineralization around the fault zone indicates that the fault zone was conduit for paleo-fluids. We conclude that the fault is not likely to develop a sealing membrane and therefore will most likely fail as a seal to fluids moving through the reservoirs modeled here. Modeling results indicate that a reduction in the effective normal stress on fault surfaces may induce failure of faults resulting in earthquakes or increased hydraulic conductivity of fractures.

The research area is located to the northern tip of Tuzgolu fault zone in the junction of neotectonic structures, namely, EskiSehir-Cihanbeyli, Sungurlu-Kirikkale and Tuzg&ouml / l&uuml / fault zones (Central Anatolia). The study is carried out in Paleocene sequences of PaSadag group on the structural analysis of bed, gash vein, fault and fault plane slippage data. The method of study based on i) the rose and stereo analysis of the planar structure (beds, gash veins and faults) on ROCKWORKS 2009 software and ii) on fault slip analysis on ANGELIER 1979 software. The bed analyses done on 605 measurements manifest N10&deg / -20&deg / E bedding attitude. The analysis done on 64 gash veins shows a general trend of NNE-SSW (N15&deg / E). The final analysis done on 160 fault planes pointed out a general trend of NNWSSE (N20&deg / W). Analysis based on the fault plane slip data manifest two stages of faulting under almost NE-SW compression during post-Paleocene &ndash / pre-Miocene period and one stage of faulting under WNW-ESE extension most probably during post-Miocene. To conclude, the Paleocene sequences are deformed continuously under WNW-ESE directed compression which is followed by a NE-SW to N-S compression resulted in the development of a reverse to dextral strike slip faulting during post-Paleocene &ndash / pre-Miocene period.

The geology of the Sierra Mojada silver-lead-zinc mining district gives new insights into the stratigraphic evolution of the Coahuila Block and the Coahuila Folded Belt and the history of deformation along the basement-rooted San Marcos Fault Zone. Sierra Mojada provides the opportunity for substantial data collection relevant to the interaction of regional tectono-stratigraphic elements in a generally data-poor region of northeastern Mexico. Active mineral exploration has produced an extensive database of closely spaced drill core. Expansive underground workings facilitate subsurface geologic mapping. Sierra Mojada is situated at the northwestern edge of two tectono-stratigraphic provinces, the Coahuila Block, to the south, and the Coahuila Folded Belt, to the north. The San Marcos Fault, a west-northwest-trending regional structure extends through Sierra Mojada and is the informal boundary between these two provinces. Sierra Mojada is situated on uplifted and deformed late Paleozoic Ouachita siliciclastic strata intruded by Triassic diorites. This basement is diagnostic of the Coahuila Block. Basement rocks are overlain by an immature conglomerate that is interpreted to be the updip equivalent of the Jurassic La Casita Formation. The stratigraphy of Sierra Mojada principally consists of a continuous succession of Barremian through Albian carbonates unconformably overlying the basal conglomerate. The Barremian-Aptian Cupido Formation locally records deepening conditions from a clastic-influenced evaporitic interior to high energy, open water conditions. The shale and lime mudstone of the La Pena Formation were deposited during a Gulf-wide transgression that signals the end of the Aptian. The Sierra Mojada region of the Coahuila Block was inundated throughout the Aptian and was affected by the late Aptian transgression. The Albian Aurora Formation constitutes the bulk of the Cretaceous section. Sierra Mojada exposes the Aurora shelf rim, progressing from platform margin to shelf rim and platform interior facies. The structural features of Sierra Mojada affect the entire Cretaceous section. The high angle San Marcos Fault was reactivated with reverse motion during the Paleogene as a result of Laramide shortening. This juxtaposed basement and Jurassic conglomerate against the Cretaceous carbonates consistent with offset observed along the southern trace of the San Marcos Fault. A local colluvial unit suggests a lag in Laramide deformation. The carbonate strata and colluvial unit were overridden by a low angle, northeast-dipping thrust fault that placed a Neocomian through Aptian sequence atop the autochthonous Aptian-Albian carbonates. The allochthonous San Marcos Formation suggests regional-scale tectonic transport of this immature fluvial conglomerate from a downdip depozone within the Sabinas Basin. Kinematic indicators are consistent with the southwest-northeast axis for maximum compression established for Paleogene shortening throughout the Coahuila Folded Belt. The thrust fault bisects the principal ore zone within the Lower Aurora and upper La Pena Formations. This relation constrains the minimum age of ore emplacement to the Paleogene and suggests mineralization was genetically tied to the late stages of the Laramide Orogeny. / text

The ENE-trending Himalayan fold-thrust belt in Pakistan exhibits contrasting deformation styles both along and across the strike. The centrifuge modelling technique has been used to investigate these variations in structural style. For the purpose of modelling, the Salt Range and Potwar Plateau (SR/PP) stratigraphy has been grouped into four mechanical units. From bottom to top these are the Salt Range Formation, carapace unit (Cambrian-Eocene platform sequences), Rawalpindi Group, and Siwalik Group. These stratigraphic units of alternating competence, composed of thin layers of plasticine modelling clay and silicone putty, rest on a rigid base plate that represents the crystalline basement of the Indian plate. The models are built at a linear scale ratio of ~10-6 (1mm=1km) and deformed in a centrifuge at 4000g. The models are subjected to horizontal shortening by collapse and lateral spreading of a “hinterland wedge” which simulates overriding by the Himalayan orogen (above the Main Boundary Thrust). The models of the central SR/PP show that the accretionary wedge develops a prominent culmination structure with fault-bend fold geometry over the frontal ramp, while the eastern SR/PP is more internally deformed by detachment folds, fault-propagation folds and pop-up and pop-down structures. Model results show that the transition from fault-bend fold to detachment-fold and fault-propagation-fold geometry in the prototype may take place in a transfer zone marked by an S-bend structure (Chambal Ridge and Jogi Tilla) at the surface and the lateral ramp in the subsurface. Moreover, the models suggest that an oblique ramp below the Kalabagh strike-slip connecting the two frontal ramps below the Surghar Range and the central Salt Range developed similar structure that can be observed in the prototype. The model results also show that the Northern Potwar Deformed Zone may have been developed over ductile substrata due to the close similarity between the models and the prototype structures. The deformation style in the models illustrates the importance of mechanical stratigraphic and basement ramp systems in the evolution and the structural styles of the SR/PP. / Thesis (Master, Geological Sciences & Geological Engineering) -- Queen's University, 2010-07-29 19:42:25.027

Bulk rock strength is greatly dependent on fracture density, so that reductions in rock strength associated with faulting and fracturing should be reflected by reduced shear coupling and hence S-wave velocity. This study is carried out along the Canterbury rangefront and in Otago. Both lie within the broader plate boundary deformation zone in the South Island of New Zealand. Therefore built structures are often, , located in areas where there are undetected or poorly defined faults with associated rock strength reduction. Where structures are sited near to, or across, such faults or fault-zones, they may sustain both shaking and ground deformation damage during an earthquake. Within this zone, management of seismic hazards needs to be based on accurate identification of the potential fault damage zone including the likely width of off-plane deformation. Lateral S-wave velocity variability provides one method of imaging and locating damage zones and off-plane deformation. This research demonstrates the utility of Multi-Channel Analysis of Surface Waves (MASW) to aid land-use planning in such fault-prone settings. Fundamentally, MASW uses surface wave dispersive characteristics to model a near surface profile of S-wave velocity variability as a proxy for bulk rock strength. The technique can aid fault-zone planning not only by locating and defining the extent of fault-zones, but also by defining within-zone variability that is readily correlated with measurable rock properties applicable to both foundation design and the distribution of surface deformation. The calibration sites presented here have well defined field relationships and known fault-zone exposure close to potential MASW survey sites. They were selected to represent a range of progressively softer lithologies from intact and fractured Torlesse Group basement hard rock (Dalethorpe) through softer Tertiary cover sediments (Boby’s Creek) and Quaternary gravels. This facilitated initial calibration of fracture intensity at a high-velocity-contrast site followed by exploration of the limits of shear zone resolution at lower velocity contrasts. Site models were constructed in AutoCAD in order to demonstrate spatial correlations between S-wave velocity and fault zone features. Site geology was incorporated in the models, along with geomorphology, river profiles, scanline locations and crosshole velocity measurement locations. Spatial data were recorded using a total-station survey. The interpreted MASW survey results are presented as two dimensional snapshot cross-sections of the three dimensional calibration-site models. These show strong correlations between MASW survey velocities and site geology, geomorphology, fluvial profiles and geotechnical parameters and observations. Correlations are particularly pronounced where high velocity contrasts exist, whilst weaker correlations are demonstrated in softer lithologies. Geomorphic correlations suggest that off-plane deformation can be imaged and interpreted in the presence of suitable topographic survey data. A promising new approach to in situ and laboratory soft-rock material and mass characterisation is also presented using a Ramset nail gun. Geotechnical investigations typically involve outcrop and laboratory scale determination of rock mass and material properties such as fracture density and unconfined compressive strength (UCS). This multi-scale approach is espoused by this study, with geotechnical and S-wave velocity data presented at multiple scales, from survey scale sonic velocity measurements, through outcrop scale scanline and crosshole sonic velocity measurements to laboratory scale property determination and sonic velocity measurements. S-wave velocities invariably increased with decreasing scale. These scaling relationships and strategies for dealing with them are investigated and presented. Finally, the MASW technique is applied to a concealed fault on the Taieri Ridge in Macraes Flat, Central Otago. Here, high velocity Otago Schist is faulted against low velocity sheared Tertiary and Quaternary sediments. This site highlights the structural sensitivity of the technique by apparently constraining the location of the principal fault, which had been ambiguous after standard processing of the seismic reflection data. Processing of the Taieri Ridge dataset has further led to the proposal of a novel surface wave imaging technique termed Swept Frequency Imaging (SFI). This inchoate technique apparently images the detailed structure of the fault-zone, and is in agreement with the conventionally-determined fault location and an existing partial trench. Overall, the results are promising and are expected to be supported by further trenching in the near future.