Global ETD Search

1	Development of a Flexural Yielding Energy Dissipation Device for Controlled Rocking Masonry Walls Li, Jeff (Jie Fei) January 2019 (has links) Steel flexural yielding arms can be an effective energy dissipation device for several seismic force resisting systems, including controlled rocking masonry walls. In controlled rocking masonry walls, uplift of the wall from the foundation is allowed in a way that can localize damage and minimize post-earthquake residual drifts. However, along with other modes of failure, sliding of the rocking walls can increase drifts and damage if not adequately addressed. Controlled rocking systems have different alternatives to prevent sliding, which include the use of additional mechanical components (e.g. metal stoppers) at the corners to resist lateral forces while allowing the wall rocking motion. However, these mechanical components hinder the constructability of the wall in some cases. The use of an energy dissipation device (i.e. steel flexural yielding arm) to also prevent the wall sliding mechanism has not been fully explored to date. The development of an easily replaceable energy dissipation device with the ability to simultaneously resist sliding demands is expected to maintain the overall performance of controlled rocking masonry walls, while also enhancing post-earthquake repairability. The objective of the current study is to experimentally investigate the effect of axial forces on the behaviour of steel flexural yielding arms under cyclic loading. In this respect, the study first presents a description of the experimental program, test setup, and instrumentation. Next, the experimental results of the tested specimens are discussed in terms of the effect of axial forces on the load, displacement, and energy dissipation capacities of the tested devices. Finally, new design equations that account for axial forces are proposed and verified against the experimental data along with a finite element model. Based on the results, recommendations are given for the further development of externally attached and replaceable flexural yielding arms for controlled rocking masonry walls. / Thesis / Master of Applied Science (MASc) / Controlled rocking masonry walls can be a cost-efficient alternative to traditional masonry shear walls because of their enhanced performance, specifically to reduce and localize structural damage induced by seismic loads. However, a controlled rocking wall requires additional energy dissipation devices or post-tensioning techniques to compliment the rocking wall to achieve the desired performance. This thesis explores and improves a type of energy dissipation device for controlled rocking masonry walls and aims to provide detailed design specifications for professional engineers. A design and considerations from previous studies are discussed, followed by the experimental validation, and finally new design equations are proposed for this type of reliable, flexural energy dissipation device. Controlled Rocking Masonry Walls Energy Dissipation Device Flexural Yielding Seismic Design Base Shear
2	Rehabilitation of Exterior RC Beam-Column Joints using Web-Bonded FRP Sheets Mahini, Seyed Saeid Unknown Date (has links) In a Reinforced Concrete (RC) building subjected to lateral loads such as earthquake and wind pressure, the beam to column joints constitute one of the critical regions, especially the exterior ones, and they must be designed and detailed to dissipate large amounts of energy without a significant loss of, strength, stiffness and ductility. This would be achieved when the beam-column joints are designed in such a way that the plastic hinges form at a distance away from the column face and the joint region remain elastic. In existing frames, an easy and practical way to implement this behaviour following the accepted design philosophy of the strong-column weak-beam concept is the use a Fibre Reinforced Plastic (FRP) retrofitting system. In the case of damaged buildings, this can be achieved through a FRP repairing system. In the experimental part of this study, seven scaled down exterior subassemblies were tested under monotonic or cyclic loads. All specimens were designed following the strong-column weak-beam principal. The three categories selected for this investigation included the FRP-repaired and FRP-retrofitted specimens under monotonic loads and FRP-retrofitted specimen under cyclic loads. All repairing/retrofitting was performed using a new technique called a web-bonded FRP system, which was developed for the first time in the current study. On the basis of test results, it was concluded that the FRP repairing/retrofitting system can restore/upgrade the integrity of the joint, keeping/upgrading its strength, stiffness and ductility, and shifting the plastic hinges from the column face toward the beam in such a way that the joint remains elastic. In the analytical part of this study, a closed-form solution was developed in order to predict the physical behaviour of the repaired/retrofitted specimens. Firstly, an analytical model was developed to calculate the ultimate moment capacity of the web-bonded FRP sections considering two failure modes, FRP rupture and tension failure, followed by an extended formulation for estimating the beam-tip displacement. Based on the analytical model and the extended formulation, failure mechanisms of the test specimens were implemented into a computer program to facilitate the calculations. All seven subassemblies were analysed using this program, and the results were found to be in good agreement with those obtained from experimental study. Design curves were also developed to be used by practicing engineers. In the numerical part of this study, all specimens were analysed by a nonlinear finite element method using ANSYS software. Numerical analysis was performed for three purposes: to calculate the first yield load of the specimens in order to manage the tests; to investigate the ability of the web-bonded FRP system to relocate the plastic hinge from the column face toward the beam; and to calibrate and confirm the results obtained from the experiments. It was concluded that numerical analysis using ANSYS could be considered as a practical tool in the design of the web-bonded FRP beam-column joints. Reinforced concrete Reinforcement Bar strong-column weak-beam principal Exterior Beam-Column Joints Core Small scale modelling Experimental Test set-up Control Plain specimen Rehabilitation Retrofitting retrofitted Repair Repaired Repairing Strengthening Controlling Relocating Plastic hinge Pre-cracking Cracking Crushing Post-cracking Crack Cracked Penetration Damaged Pre-cracked Web-Bonded Wrapping De-bonding Fibre Reinforced Plastic FRP Sheets Composite Confinement Monotonic loads Cyclic loading Loads Displacement control Load control Regime Phase Loading sequence Procedure Available ductility factor Curvature ductility factor Ultimate First yield Flexural yielding Strength Moment Stiffness Failure mechanism Modes Sudden Brittle failure Measured beam-tip displacement Deflection Numerical analysis ANSYS Solid65 Solid45 Link8 Non-linear Finite Element (FE) Convergence criteria Analytical Closed from FRP rupture tension failure Compression failure Minimum thickness Maximum thickness Compressive Tensile Steel Ratio Design charts Effective Moment of Inertia Compatibility Strain Stress

Search results

Development of a Flexural Yielding Energy Dissipation Device for Controlled Rocking Masonry Walls

Rehabilitation of Exterior RC Beam-Column Joints using Web-Bonded FRP Sheets