No description available.

No description available.

No description available.

The motion of shock waves is important in many fields of engineering and increasingly so with medical applications and applications to inertial confinement fusion technologies. The flow structures that moving shock waves create when they encounter a change in area is complex and can be difficult to understand. Previousresearchers have carried out experimental studies and many numerical studies looking at this problem in more detail. There has been a discrepancy between numerical and experimental work which had remained unanswered. One of the aims of this project is to try and resolve the discrepancy between numerical and experimental work and try to investigate what experimental techniques are suitable for work of this type and the exact way in which they should be applied. Most previous work has focused on sharp changes in geometry which induce immediate flow separation. In this project rounded corners will also be investigated and the complex flow features will be analyzed.Two geometries, namely a sharp 172 degree knife-edge and a 2.8 mm radius rounded corner will be investigated at three experimental pressure ratios of 4, 8 and 12 using air as the driver gas. This yields experimental shock Mach numbers of 1.28, 1.46 and 1.55. High-speed schlieren and shadowgraph photography with varying levels of sensitivity were used to qualitatively investigate the wave structures. Particle image velocimetry (PIV), pressure-sensitive paint (PSP) and traditional pressure transducers were used to quantify the flow field. Numerical simulations were performed using the commercial package Fluent to investigate the effect of numerical schemes on the flow field produced and for comparison with the experimental results. The sharp geometry was simulated successfully using an inviscid simulation while the rounded geometry required the addition of laminar viscosity. Reynolds number effects will be only sparsely referred to in this project as the flows under investigation show largely inviscid characteristics. As the flow is developing in time rather than in space, quotation of a distance-based Reynolds number is not entirely appropriate; however, Reynolds number based on the same spatial location but varying in time will be mentioned. The density-based diagnostics in this project were designed to have a depth of field appropriate to the test under consideration. This approach has been used relatively few times despite its easy setup and significant impact on the results. This project contains the first quantative use of PIV and PSP to shock wave diffraction. Previous studies have almost exclusively used density-based diagnostics which, although give the best impression of the flow field, do not allow for complete analysis and explanation of all of the flow features present. PIV measurements showed a maximum uncertainty of 5% while the PSP measurements showed an uncertainty of approximately 10%.The shock wave diffraction process, vortex formation, shear layer structure, secondary and even tertiary expansions and the shock vortex interaction were investigate. The experimental results have shown that using one experimental technique in isolation can give misleading results. Only by using a combination of experimental techniques can we achieve a complete understanding of the flow field and draw conclusions on the validity of the numerical results. Expanding the range of the experimental techniques currently in use is vital for experimental aerodynamic testing to remain relevant in an industry increasingly dominated by numerical research. To this end, significant research work has been carried out on extending the range of the PSP technique to allow for the capture of shock wave diffraction, one of the fastest transient fluid processes, and for applications to low-speed flow (< 20 ms−1).

Fluid dynamicists are always in need of innovative instruments for flow velocity measurements. An ideal instrument would be non-intrusive, have a very fine spatial resolution as well as a very fine temporal resolution, be able to measure three-components of velocity, and be compact. Through recent advancements, laser Doppler velocimetry can now meet all of those requirements making it an important part of aerodynamicist's research toolbox. The first paper presented in this manuscript style thesis explains the development of an advanced three-velocity component, spatially-resolving laser-Doppler velocimetry (LDV) system for highly resolved velocity measurements in situations with limited optical access. The new instrument, a next generation version of the previously developed 'comprehensive' LDV technology, enables measurements of three components of velocity and particle position in the axial direction all through a single transceiving lens. Described here is the design process and the final design for the 'compact, comprehensive' LDV (Comp²LDV). The probe was designed to achieve ± 10 micron root-mean-square uncertainties in axial particle position, which combined with the long measurement volume, allow researchers to obtain a three-velocity-component velocity statistics profiles over a span of approximately 1.5mm without the need for traversing. Results from measurements in a flat plate turbulent boundary layer very near the wall have compared favorably to data from previous studies. The second paper focuses on the motion and evolution of coherent structures in supersonic jet flows and how that relates to the intense noise the flows generate. As a preliminary study to experimentally address these relationships, novel non-intrusive measurements using two-component laser Doppler velocimetry (LDV) have been conducted at exceptionally high data rates to lend insight into the statistical behavior of noise-generating flow structures. A new heated supersonic jet facility has been constructed to provide supersonic flow at total temperatures ratios (T₀/Tₐ) up to 3. In the present work, the instrumentation is validated via comparison of LDV measurements along the centerline of a screeching cold jet with microphone and high-speed shadowgraph results. Reynolds stress spectra are presented for an over-expanded case (nozzle pressure ratio of 3.2) of a design Mach number 1.65 nozzle operated cold (T₀/Tₐ = 1). A preliminary study was then conducted in the near-nozzle shear layer, up to x/d = 4.0, at design nozzle pressure ratio (4.58) and total temperature ratio of 2.0. Results are presented for Reynolds stress time-delay correlations and power spectra at Re_d = 1.1M for this case. The stream-wise Reynolds normal stress spectra are compared with published spectral behavior reported by other researchers, indicating a similar spectral shape in the downstream stations as previously measured with LDV and hot wire anemometry for cold jets, but which differ in shape from density-based techniques. / Master of Science

An advanced laser-Doppler velocimeter is designed to acquire fully-resolved turbulence structural measurements in high Reynolds number two- and three-dimensional turbulent boundary layers. The new instrument combines, for the first time, new techniques allowing for the direct measurement of particle acceleration and sub-measurement-volume-scale position resolution so that second-order 3D particle trajectories may be measured at high repetitions. Using these measurements, several terms in the Reynolds stress transport equations may be directly estimated, giving new data for modeling and understanding the processes leading to the transport of turbulence in boundary layer flows. Due to the unique performance of the probe, many aspects of LDV instrumentation development were addressed. The LDV configuration was optimized for lowest uncertainties by considering the demanding applications of particle position and acceleration measurements. Low noise light detection and signal conditioning was specified for the three electronic channels. A high-throughput data acquisition system allows for exceptional burst rate acquisition. Signal detection and processing algorithms have been implemented which draw from previous techniques but also address distinctive problems with the current system. In short, the instrument was designed to advance the state-of-the-art in LDV systems. Measurements presented include turbulence dissipation rate and fluctuating velocity-pressure gradient correlations that have been measured in 2D and 3D turbulent boundary layers using the unique capabilities of the CompLDV--many of these measurements are the first of their kind ever acquired in high Reynolds number turbulent flows. The flat-plate turbulent boundary layer is studied at several momentum thickness Reynolds numbers up to 7500 to examine Reynolds numbers effects on terms such as the velocity-pressure gradient correlation and the dissipation rate in the Reynolds transport equations. Measurements are also presented in a pressure-driven three-dimensional turbulent boundary layer created upstream from a wing-body junction. The current results complement the extensive data from previous studies and provide even richer depth of knowledge on the most-completely-documented 3D boundary layer flow in existence. Further measurements include the wakes of three circular-cylinder protuberances submerged in a constant pressure turbulent boundary layer. / Ph. D.

The hypersonic laminar to turbulent transition problem above Mach 10 is addressed experimentally in the short duration VKI Longshot gun tunnel. Reentry conditions are partially duplicated in terms of Mach and Reynolds numbers. Pure nitrogen is used as a test gas with flow enthalpies sufficiently low to avoid its dissociation, thus approaching a perfect gas behavior. The stabilizing effects of Mach number and nosetip bluntness on the development of natural boundary layer disturbances are evaluated over a 7 degrees half-angle conical geometry without angle of attack. <p><p>Emphasis is initially placed on the flow characterization of the Longshot wind tunnel where these experiments are performed. Free-stream static pressure diagnostics are implemented in order to complete existing stagnation point pressure and heat flux measurements on a hemispherical probe. An alternative method used to determine accurate free-stream flow conditions is then derived following a rigorous theoretical approach coupled to the VKI Mutation thermo-chemical library. Resulting sensitivities of free-stream quantities to the experimental inputs are determined and the corresponding uncertainties are quantified and discussed. The benefits of this different approach are underlined, revealing the severe weaknesses of traditional methods based on the measurement of reservoir conditions and the following assumptions of an isentropic and adiabatic flow through the nozzle. The operational map of the Longshot wind tunnel is redefined accordingly. The practical limits associated with the onset of nitrogen flow condensation under non-equilibrium conditions are also accounted for. <p><p>Boundary layer transition experiments are then performed in this environment with free-stream Mach numbers ranging between 10-12. Instrumentation along the 800mm long conical model includes flush-mounted thermocouples and fast-response pressure sensors. Transition locations on sharp cones compare favorably with engineering correlations. A strong stabilizing effect of nosetip bluntness is reported and no transition reversal regime is observed for Re_RN<120000. Wavelet analysis of wall pressure traces denote the presence of inviscid instabilities belonging to Mack's second mode. An excellent agreement with Linear Stability Theory results is obtained from which the N-factor of the Longshot wind tunnel in these conditions is inferred. A novel Schlieren technique using a short duration laser light source is developed, allowing for high-quality flow visualization of the boundary layer disturbances. Comparisons of these measurement techniques between each other are finally reported, providing a detailed view of the transition process above Mach 10. / Doctorat en Sciences de l'ingénieur / info:eu-repo/semantics/nonPublished