1 |
Boundary-Layer Stability and Transition on a Flared Cone in a Mach 6 Quiet Wind TunnelHofferth, Jerrod William 16 December 2013 (has links)
A key remaining challenge in the design of hypersonic vehicles is the incomplete understanding of the process of boundary-layer transition. Turbulent heating rates are substantially higher than those for a laminar boundary layer, and large uncertainties in transition prediction therefore demand conservative, inefficient designs for thermal protection systems. It is only through close collaboration between theory, experiment, and computation that the state of the art can be advanced, but experiments relevant to flight require ground-test facilities with very low disturbance levels.
To enable this work, a unique Mach 6 low-disturbance wind tunnel, previously of NASA Langley Research Center, is established within a new pressure-vacuum blow-down infrastructure at Texas A&M. A 40-second run time at constant conditions enables detailed measurements for comparison with computation. The freestream environment is extensively characterized, with a large region of low-disturbance flow found to be reliably present for unit Reynolds numbers Re < 11×10^6 m-1.
Experiments are performed on a 5º half-angle flared cone model at Re = 10×10^6 m-1 and zero angle of attack. For the study of the second-mode instability, well-resolved boundary-layer profiles of mean and fluctuating mass flux are acquired at several axial locations using hot-wire probes with a bandwidth of 330 kHz. The second mode instability is observed to undergo significant growth between 250 and 310 kHz. Mode shapes of the disturbance agree well with those predicted from linear parabolized stability equation (LPSE) computations. A 17% (40 kHz) disagreement is observed in the frequency for most-amplified growth between experiment and LPSE. Possible sources of the disagreement are discussed, and the effect of small misalignments of the model is quantified experimentally.
A focused schlieren deflectometer with high bandwidth (1 MHz) and high signal-to-noise ratio is employed to complement the hot-wire work. The second-mode fundamental at 250 kHz is observed, as well as additional harmonic content not discernible in the hot-wire measurements at two and three times the fundamental. A bispectral analysis shows that after sufficient amplification of the second mode, several nonlinear mechanisms become significant, including ones involving the third harmonic, which have not hitherto been reported in the literature.
|
2 |
Characterization of the Quiet Flow Freestream and a Flat Plate Model in the Boeing/AFOSR Mach 6 Quiet TunnelDerek V Mamrol (11711882) 22 November 2021 (has links)
<div>The ambient pressure fluctuations within a wind tunnel test environment can severely affect the boundary layer transition witnessed on test articles The Boeing/AFOSR Mach 6 Quiet Tunnel was designed to minimize these fluctuations, also referred to as noise, and is the world's premier facility for studying hypersonic boundary layer transition in a quiet flow environment. All experiments performed for this work were conducted at this facility.</div><div><br></div><div> </div><div> The freestream flow field of this tunnel has been characterized multiple times since its creation, however an extensive three-dimensional spatial sweep has never been conducted. A pitot rake model was designed to allow for an extensive spatial survey of tunnel noise. This model created measurement capabilities that were previously unknown to the BAM6QT facility, including the ability to take concurrent freestream pitot probe measurements. The performance of this new measurement method was evaluated, and suggestions for future verification tests are made. The pitot rake appears to suffer from probe-probe interactions in certain configurations, and has demonstrated variation in measurements that depends on the individual sensor used.</div><div><br></div><div> </div><div> This new measurement apparatus was used to investigate the effect that cavities in the tunnel wall created by the installation of new optical windows had on the freestream noise level. A control dataset corresponding to a perfectly conformal tunnel wall was not collected during this work. The experiments conducted provide evidence that the tunnel wall cavities do increase the noise downstream of their location by approximately 100%, however a control dataset is needed to verify this finding.</div><div><br></div><div> </div><div> In addition to tunnel characterization, a novel flat plate model was evaluated for use in the BAM6QT. This model was intended for use as a platform for observing second mode instability growth. These experiments show that the initial flat plate geometry proved incompatible with the BAM6QT as the tunnel could not achieve nominal flow conditions with the model installed. The flat plate model was streamlined to rectify the startup issue, but no evidence of the second mode instability was found. A 2.5° half angle cone is being designed to replace the flat plate model as a platform for the continuation of this project.</div>
|
3 |
Longshot hypersonic wind tunnel flow characterization and boundary layer stability investigationsGrossir, Guillaume 01 July 2015 (has links)
The hypersonic laminar to turbulent transition problem above Mach 10 is addressed experimentally in the short duration VKI Longshot gun tunnel. Reentry conditions are partially duplicated in terms of Mach and Reynolds numbers. Pure nitrogen is used as a test gas with flow enthalpies sufficiently low to avoid its dissociation, thus approaching a perfect gas behavior. The stabilizing effects of Mach number and nosetip bluntness on the development of natural boundary layer disturbances are evaluated over a 7 degrees half-angle conical geometry without angle of attack. <p><p>Emphasis is initially placed on the flow characterization of the Longshot wind tunnel where these experiments are performed. Free-stream static pressure diagnostics are implemented in order to complete existing stagnation point pressure and heat flux measurements on a hemispherical probe. An alternative method used to determine accurate free-stream flow conditions is then derived following a rigorous theoretical approach coupled to the VKI Mutation thermo-chemical library. Resulting sensitivities of free-stream quantities to the experimental inputs are determined and the corresponding uncertainties are quantified and discussed. The benefits of this different approach are underlined, revealing the severe weaknesses of traditional methods based on the measurement of reservoir conditions and the following assumptions of an isentropic and adiabatic flow through the nozzle. The operational map of the Longshot wind tunnel is redefined accordingly. The practical limits associated with the onset of nitrogen flow condensation under non-equilibrium conditions are also accounted for. <p><p>Boundary layer transition experiments are then performed in this environment with free-stream Mach numbers ranging between 10-12. Instrumentation along the 800mm long conical model includes flush-mounted thermocouples and fast-response pressure sensors. Transition locations on sharp cones compare favorably with engineering correlations. A strong stabilizing effect of nosetip bluntness is reported and no transition reversal regime is observed for Re_RN<120000. Wavelet analysis of wall pressure traces denote the presence of inviscid instabilities belonging to Mack's second mode. An excellent agreement with Linear Stability Theory results is obtained from which the N-factor of the Longshot wind tunnel in these conditions is inferred. A novel Schlieren technique using a short duration laser light source is developed, allowing for high-quality flow visualization of the boundary layer disturbances. Comparisons of these measurement techniques between each other are finally reported, providing a detailed view of the transition process above Mach 10. / Doctorat en Sciences de l'ingénieur / info:eu-repo/semantics/nonPublished
|
Page generated in 0.0656 seconds