Spelling suggestions: "subject:"highstrength"" "subject:"hightrength""
211 |
Flexural Resistance Factors for Partially Prestressed Members Using ASTM A 1035 Reinforcing SteelChamberlain, James M., Jr. January 2012 (has links)
No description available.
|
212 |
Static and Blast Performance of Reinforced Concrete Beams Built with High-Strength Steel and Stainless Steel ReinforcementLi, Yang 06 October 2022 (has links)
High-strength steel (HSS) conforming to ASTM A1035 is becoming increasingly used in various structural applications, including in high-rise buildings and bridges. Due to their chemistry and manufacturing process, ASTM A1035 steel bars result in a combination of high tensile strength to yield ratio and varying levels of corrosion resistance. One potential application of ASTM A1035 bars is in the blast-resistant design of concrete structures, where their use can allow for reduced steel congestion, and increased blast resistance. Despite their high initial cost, stainless steel (SS) reinforcing bars are also seeing increased use in concrete construction. Solid stainless steel bars are referenced in ASTM A955, which is applicable to various stainless steel alloys. In addition to their inherent corrosion resistance, most stainless steel bars possess greater tensile strength, and importantly, exceptional ductility, when compared to ordinary steel reinforcement. This unique combination of strength and ductility makes SS bars well-suited for blast design applications.
The overarching aim of this thesis is to gain better understanding of the blast behavior of RC flexural members designed with high-strength (HSS) and stainless steel (SS) reinforcement. This objective is achieved through a combined experimental and numerical research program. As part of the experimental research, a large set of beams, subdivided into three series, are tested under either quasi-static bending or simulated blast loads using the University of Ottawa shock-tube. Series 1 (HSC-HSS) and Series 2 (HSC-SS) aim at examining the effects of blast detailing (as recommended in modern blast codes,) on the quasi-static, blast and post-blast behaviour of high-strength concrete (HSC) beams reinforced with either ASTM A1035 high-strength bars (8 beams) or ASTM A955 stainless steel bars (16 beams). In addition to the influence of detailing, the effects of steel grade/type, steel ratio and steel fibers are also studied. Series 3 further studies the benefits of combining higher grade or higher ductility reinforcement, with more advanced ultra-high performance concrete (UHPC). This series includes 20 UHPC beams built with either ordinary, HSS or SS reinforcing bars (UHPC-NSS, UHPC-HSS and UHPC-SS). In addition to the effect of steel grade/type, concrete type, steel ratio and steel detailing are also studied.
The results from Series 1 and 2 demonstrate the benefits of implementing high-strength and stainless steel reinforcement in HSC beams subjected to blast loads, where their use leads to increased blast capacity, reduced support rotations, and higher damage tolerance. The results further demonstrate the benefits of “blast detailing” on the ductility and resilience of such beams, under both static and blast loads. The results also show that the use of steel fibers can be used to relax blast detailing in the beams with high-strength or stainless steel by increasing the required tie spacing from d/4 to d/2. The results from Series 3 confirm that the use of UHPC in beams enhances flexural response (in terms of strength and stiffness), which in turn results in superior blast resistance. Conversely, the high bond capacity of UHPC makes such beams more vulnerable to bar fracture. Increasing the steel ratio is found to effectively increase the failure displacement and ductility of the UHPC beams. The use of high-strength steel is found to increase load capacity and blast resistance, while the use of stainless steel results in remarkable ductility, which further enhances beam response under blast loading.
As part of the numerical research program, the static and blast responses of the test beams are simulated using either 2D or 3D finite element (FE) modelling, using software VecTor2 and LS-DYNA. The numerical results show that the 2D FE modelling using software VecTor2 can provide reliable predictions of the static and blast responses of the HSS or SS reinforced HSC beams built with varying detailing, in terms of load-deflection response, cracking patterns, failure mode, displacement time histories and dynamic reactions. Likewise, the 3D FE modelling using software LS-DYNA with appropriate modelling of UHPC (using the Winfrith Concrete or CSCM models) can well predict the blast responses of UHPC beams with ordinary, high-strength and stainless steel, in terms of displacement/load-time histories, damage and failure modes.
|
213 |
Anaerobic Co-Digestion of High Strength Food Waste with Municipal Sewage Sludge: An assessment of Digester Performance and gas productionPathak, Ankit Bidhan 06 June 2014 (has links)
Anaerobic digestion is perhaps the simplest and most widely accepted method for solids and residuals management in the field of wastewater treatment. An emerging trend with regard to anaerobic digestion is the addition of additional organic or industrial wastes rich in degradable material (COD) that can lead to increased methane production and reduce the energy demand of the facility.
The objective of this research was to evaluate the effect of adding significant quantities (>20% of feed volume) of High Strength Food Wastes (HSW) to digesters treating conventional municipal sludge by monitoring key parameters such as pH, influent and effluent solids, ammonia, Volatile Fatty Acids (VFAs) and alkalinity. Daily gas production was also closely monitored. Four digesters were set up and exposed to different food waste loading rates. A comparison was drawn between the performance of these reactors, one of which was fed only with sewage sludge and served as the control. If the bacteria in the system are able to metabolize this additional COD, it should show up as an increase in gas production with little or no increase in effluent COD.
Ammonia is another crucial parameter that needs to be closely watched as it can have an inhibitory effect on methane production. As part of this study, the impact of addition of free ammonium (simulating high ammonium concentration in the feed sludge or food waste) on digester performance was assessed. The digesters were closely monitored for signs of poor performance or failure. / Master of Science
|
214 |
Effect of Addition of High Strength Food Wastes on Anaerobic Digestion of Sewage SludgeVaidya, Ramola Vinay 11 June 2015 (has links)
Anaerobic co-digestion of municipal sludge and food wastes high in chemical oxygen demand (COD) has been an area of interest for waste water treatment facilities looking to increase methane production, and at the same time, dispose of the wastes and increase the revenue. However, addition of food wastes containing fats, oils and grease (FOG) to the conventional anaerobic digestion process can be difficult and pose challenges to utilities. Incorporating these wastes into the treatment plants can potentially inhibit the digestion process.
In this study four lab-scale, anaerobic digesters were operated under mesophilic conditions and fed municipal sludge. One of them served as the control, while the other three digesters were fed with different volumetric loadings of juice processing waste, cheese processing waste (whey), dissolved air flotation waste (DAF) from a food processor, and grease trap waste (GTW), in addition to the municipal sludge. The impact of these high strength wastes (HSWs) on digester performance was analyzed for a total period of 150 days.
Among the parameters analyzed were pH, total and soluble COD (tCOD and sCOD), Total and Total Volatile Solids (TS and TVS), Total Ammonia Nitrogen (TAN), Total Kjeldahl Nitrogen (TKN), Volatile Fatty Acids (VFA), Long Chain Fatty Acids (LCFA), and alkalinity. Biogas was collected and analyzed for methane content. The dewatering characteristics of digested sludge were also studied. Volatile organic sulfur compounds were analyzed on the dewatered sludge in order to monitor odors.
This study showed that different high strength wastes have different impacts on digester performance. HSWs have the ability to degrade along with municipal sludge and to increase biogas production. However, anaerobic digestion can be inhibited by the presence of FOG, and addition of these wastes might not always be cost effective. Careful selection of these wastes is necessary to ensure stable digester operation, while bringing about increases in gas production. Utilities need to be cautious before adding any high strength wastes to their digesters. / Master of Science
|
215 |
Eccentrically loaded concrete encased steel composite columnsEl-Lobody, E., Young, B., Lam, Dennis January 2011 (has links)
This paper presents a nonlinear 3-D finite element model for eccentrically loaded concrete encased steel composite columns. The columns were pin-ended subjected to an eccentric load acting along the major axis, with eccentricity varied from 0.125 to 0.375 of the overall depth (D) of the column sections. The model accounted for the inelastic behaviour of steel, concrete, longitudinal and transverse reinforcement bars as well as the effect of concrete confinement of the concrete encased steel composite columns. The interface between the steel section and concrete, the longitudinal and transverse reinforcement bars, and the reinforcement bars and concrete were also considered allowing the bond behaviour to be modelled and the different components to retain its profile during the deformation of the column. The initial overall geometric imperfection was carefully incorporated in the model. The finite element model has been validated against existing test results. The concrete strengths varied from normal to high strength (30¿110 MPa). The steel section yield stresses also varied from normal to high strength (275¿690 MPa). Furthermore, the variables that influence the eccentrically loaded composite column behaviour and strength comprising different eccentricities, different column dimensions, different structural steel sizes, different concrete strengths, and different structural steel yield stresses were investigated in a parametric study. Generally, it is shown that the effect on the composite column strength owing to the increase in structural steel yield stress is significant for eccentrically loaded columns with small eccentricity of 0.125D. On the other hand, for columns with higher eccentricity 0.375D, the effect on the composite column strength due to the increase in structural steel yield stress is significant for columns with concrete strengths lower than 70 MPa. The strength of composite columns obtained from the finite element analysis were compared with the design strengths calculated using the Eurocode 4 for composite columns. Generally, it is shown that the EC4 accurately predicted the eccentrically loaded composite columns, while overestimated the moment.
|
216 |
Experimental investigation of bond behaviour of two common GFRP bar types in high-strength concreteSaleh, N., Ashour, Ashraf, Lam, Dennis, Sheehan, Therese 07 January 2019 (has links)
Yes / Although several research studies have been conducted on investigating the bond stress – slip behaviour of Glass-Fibre Reinforced Polymer (GFRP) bars embedded in high strength concrete (HSC) using a pull-out method, there is no published work on the bond behaviour of GFRP bars embedded in high strength concrete using a hinged beam. This paper presents the experimental work consisted of testing 28 hinged beams prepared according to RILEM specifications. The investigation of bond performance of GFRP bars in HSC was carried out by analysing the effect of the following parameters: bar diameter (9.5, 12.7 and 15.9 mm), embedment length (5 and 10 times bar diameter), surface configuration (helical wrapping with slight sand coating (HW-SC) and sand coating (SC)) and bar location (top and bottom). Four hinged beams reinforced with 16 mm steel bar were also tested for comparison purposes.
The majority of beam specimens failed by pull-out. Visual inspection of the test specimens showed that the bond failure of GFRP (HW-SC) bars usually occurred owing to the bar surface damage, while the bond failure of GFRP (SC) bars was caused due to the detachment of sand coating. The GFRP bars with helical wrapping and sand coated surface configurations showed different bond behaviour and it was found that the bond performance of the sand coated surface was better than that of the helically wrapped surface. Bond strength reduced as the embedment length and bar diameter increased. It was also observed that the bond strength for the bottom bars was higher than that of the top bars. The bond strength was compared against the prediction methods given in ACI-440.1R, CSA-S806 and CSA-S6 codes. All design guidelines underestimated the bond strength of both GFRP re-bars embedded in high strength concrete. / Ministry of Higher Education in Libya for funding.
|
217 |
Microstructural Investigation Of Precipitation Hardened Cuni2s+zr Alloys For Rotor ApplicationsVega-Garcia, Jean-Paul 01 January 2010 (has links)
Industrial generator components experience high stresses and electrical fields during their service life. Material integrity is key in guaranteeing component performance. CuNi2SiZr, used as rotor wedges in generators, serve to maintain rotor slot content in place while experiencing high centrifugal stresses and low cycle fatigue during start and stop at elevated temperature. The quality and integrity of this material in service can be directly related to its microstructure, which is determined by the processing procedures of the wedges. In this study, the microstructure development in this material is evaluated to eliminate grain boundary defects by optimizing processing parameters, determining the best temperature/time combination for precipitation hardening, and determining cold work effect on aging parameters. Two chemistries containing Nickel-to-Silicon ratios of 3.2 and 3.8 were selected for analysis. Cast samples were hot extruded, cold worked, and precipitation hardened. Parameters were varied at each processing step. Five different levels of cold work (4, 5, 7, 10 and 13%) were evaluated using 5 different aging temperatures (450, 460, 470, 490 and 500°C). Each processing parameters' effect on microstructure and subsequently on hardness, conductivity, and tensile strength was recorded to assess material performance and identify grain boundary defects origination. Finding of this study identified observed grain boundary defects, using Transmission Electron Analysis, as voids/micro-tears. These defects on grain boundary are detrimental to low cycle fatigue, creep rupture and tensile strength properties and important aspects of the material performance. Grain boundary defects were observed at all levels of cold work, however, origination of defects was only observed in grain sizes larger than 50µm. The strengthening phases for the CuNi2Si+Zr alloy system were identified as Ni2Si and Cr3Si. The Nickel-to-Silicon ratio had an evident effect on the electrical conductivity of the material. However, aging benefits were not clearly established between the two Nickel-to-Silicon ratios.
|
218 |
Selective oxidation and reactive wetting of an Fe-0.15C-5.5Mn-1.17Si-1Al advanced high strength steel (AHSS) during hot-dip galvanizingGol, Saba January 2021 (has links)
Third-generation advanced high-strength steels (3G AHSS) are being developed to assist in vehicle light weighting so that fuel efficiency may be improved without sacrificing passenger safety. 3G-AHSS have received significant interest from the automotive industry as a critical candidate for their unique combination of high strength and ductility. However, due to selective oxidation of the principal alloying elements such as Mn, Si, Al, and Cr at the steel surface during the annealing stage prior to immersion in the galvanizing Zn(Al, Fe) bath, the process of continuous hot-dip galvanizing of these steel is challenging. This thesis determined the influence of annealing process parameters such as oxygen partial pressure and annealing time, on the selective oxidation and reactive wetting of an Fe-0.15C-5.56Mn-1.17Si-1Al (wt%) prototype 3G AHSS during intercritical annealing as well as continuous galvanizing.
Simulated annealing and galvanizing were conducted on the prototype Fe-0.15C-5.56Mn-0117Si-1Al (wt%) 3G steel; Intercritical annealing heat treatments were carried out at 690˚C in a N2-5 vol pct H2 process atmosphere under dew points of 223 K (–50 °C), 243 (–30 °C) and 268 K (–5 °C). MnO was the major oxide formed at the outmost layer of the external oxides on all annealed samples. The experimental parameters, on the other hand, had a substantial impact on the morphology, distribution, thickness, and surface oxide coverage.
The greatest Mn surface concentration as well as maximum surface oxide coverage and thickness was obtained by annealing the panels under the 223 K (–50 °C) and 243 (–30 °C) dp process atmospheres. The oxides formed under these process atmospheres largely comprised coarse, compact, and continuous film nodules. In contrast, MnO nodules formed under the 268 K (–5 °C) dewpoint process, exhibited wider spacing between finer and thinner nodules, which was consistent with the internal oxidation mode, while under 223 K (–50 °C) dp process atmosphere, generally external oxidation took place.
Poor reactive wetting was obtained for the panels annealed under the 223 K (–50 °C) dp process atmosphere for both the 60 s and 120 s holding times as well as the 243 K (–30 °C) dp process atmosphere for 120 s. This was attributed to the formation of a thick, compact oxide layer on the steel surface, which acted as a barrier between the substrate and Zn bath, preventing Fe dissolution from the substrate surface for the formation of the desired Fe2Al5Znx interfacial layer. However, a well-developed interfacial Fe-Al intermetallic layer was formed under the 268 K (–5 °C) and 243 (–30 °C) dp process atmospheres for intercritical annealing times of 60 s, which is indicative of a good reactive wetting since the thinner and nodule-like oxides on the steel surface after annealing encourage the reactive wetting. External oxides morphology plays a dominant role in facilitating the contact between Zn-alloy bath and the substrate via different mechanisms such as aluminothermic reduction which occurred for the sample annealed under the 268 K (–5 °C) dp process atmosphere. / Thesis / Master of Applied Science (MASc)
|
219 |
Influence of Fine-scale Niobium Carbonitride Precipitates on Hydrogen-Induced Cracking of X70 Pipeline SteelWojnas, Caroline Theresa January 2021 (has links)
The microstructure of steel is well known to affect hydrogen-induced cracking (HIC) susceptibility by having certain heterogeneities serving as effective hydrogen trap sites. A consensus on whether or not fine-scale niobium carbide (NbC), nitride (NbN) and carbonitride (Nb(C,N)) precipitates can behave as effective hydrogen traps has yet to be established. The H-trapping capacity of Nb precipitates in a Fe-C-Mn-Nb model steel was investigated with the goal of minimizing embrittlement effects and improving the design of X70 pipeline grade steel for sour service oil and gas applications. First, a heat treatment was applied to the model steel to change the Nb-based precipitate size distribution, which was subsequently characterized via transmission electron microscopy, electron energy loss spectroscopy, and atom probe tomography. The experimental heat treatment increased the number of fine-scale precipitates (<15 nm) that are ideal for APT characterization. NbN and NbC precipitates of various stoichiometries were confirmed within the steel. Further, a custom electrolytic H-charging device was designed, fabricated, and validated using thermal desorption spectroscopy. Additionally, the extent of galvanic corrosion between NbC and NbN and the steel matrix was determined using custom scaled-up particle matrix specimens. Potentiodynamic polarizations conducted using active and passivating electrolytes revealed the relative nobility of the materials. Both NbC and NbN particles were more noble than the steel matrix; thus, possessing driving force for galvanic corrosion, with the particles serving as cathodes. Future studies involving electrolytic charging of the steel in a D-based electrolyte coupled with atom probe tomography will facilitate the direct observation of H-trapping sites relative to various Nb-based precipitates and contribute to an improved understanding of the mechanisms governing HIC. / Thesis / Master of Science in Materials Science and Engineering (MSMSE)
|
220 |
Flexural And Tensile Properties Of Thin, Very High-Strength, Fiber-Reinforced Concrete PanelsRoth, Michael Jason 15 December 2007 (has links)
This research was conducted to characterize the flexural and tensile characteristics of thin, very high-strength, discontinuously reinforced concrete panels developed by the U.S. Army Engineer Research and Development Center. Panels were produced from a unique blend of cementitous material and fiberglass reinforcing fibers, achieving compressive strength and fracture toughness levels that far exceeded that of typical concrete.The research program included third-point flexural experiments, novel direct tension experiments, implementation of micromechanically based analytical models, and development of finite element numerical models. The experimental, analytical, and numerical efforts were used conjunctively to determine parameters such as elastic modulus, first-crack strength, post-crack modulus and fiber/matrix interfacial bond strength. Furthermore, analytical and numerical models implemented in the work showed potential for use as design tools in future engineered material improvements.
|
Page generated in 0.0392 seconds