L’alliage L-605 est un superalliage base cobalt combinant une haute résistance et une bonne ductilité, de plus il est biocompatible et présente une bonne résistance a la corrosion. Dû a son inertie chimique dans le corps humain, ce matériau a été utilise avec succès pour fabriquer des valves cardiaques et des stents. Le contrôle de la microstructure peut influencer grandement les propriétés mécaniques : notamment un raffinement des grains est susceptible d’augmenter d’avantage la résistance et serait intéressant pour permettre de fabriquer des stents selon une architecture plus fine. L’ajustement de la distribution de taille de grains à travers le phénomène de recristallisation lors de la déformation à chaud apparait comme une solution pratique pour ajuster les propriétés mécaniques du matériau. Pour contrôler la microstructure et choisir les conditions de procédé optimales, les mécanismes mis en jeu lors de la recristallisation dynamique et l’effet des conditions de déformation sur la taille de grain doivent être compris et prévisibles par des outils théorique. Les propriétés mécaniques du matériau à haute température sont déterminées par des essais de compression à chaud. L’évolution microstructurale du matériau lors de la compression est analysée par microscopie optique et électronique (EBSD, TEM). Le phénomène de recristallisation dynamique continue est mis en évidence, et procède par nucléation de nouveaux grains aux joints de grain. La corrélation entre le comportement mécanique à chaud et l’évolution microstructurale est déterminée expérimentalement. Les conditions optimales de déformation impliquant la recristallisation dynamique sont déterminées, et la microstructure résultante est étudiée en détail. De nouveaux outils théoriques permettant de prévoir les conditions de recristallisation et d’extraire les paramètres physiques du matériau a partir des données expérimentales sont proposés. Enfin, la recristallisation dynamique est modélisée analytiquement, et permet de prédire le comportement mécanique et l’évolution de la taille de grain lors de la déformation. / Co-20Cr-15W-10Ni alloy (L-605) is a cobalt-based superalloy combining high strength with keeping high ductility, biocompatible and corrosion resistant. It has been used successfully for heart valves for its chemical inertia, and this alloy is a good candidate for stent elaboration. Control of grain size distribution can lead to significant improvement of mechanical properties: in one hand grain refinement enhance the material strength, and on the other hand large grains provide the ductility necessary to avoid the rupture in use. Therefore, tailoring the grain size distribution is a promising way to adapt the mechanical properties to the targeted applications. The grain size can be properly controlled by dynamic recrystallization during the forging process. Therefore, the comprehension of the recrystallization mechanism and its dependence on forging parameters is a key point of microstructure design approach. The optimal conditions for the occurrence of dynamic recrystallization are determined, and correlation between microstructure evolution and mechanical behavior is investigated. Compression tests are carried out at high-temperature on Thermec-master Z and Gleeble forging devices, followed by gas or water quench. Mechanical behavior of the material at high temperature is analyzed in detail, and innovative methods are proposed to determine the metallurgical mechanisms at stake during the deformation process. Mechanical properties of the material after hot-working and annealing treatments are investigated. The grain growth kinetics of L-605 alloy is determined, and experimental results are compared with the static recrystallization process. Microstructures after hot deformation are evaluated using SEM-EBSD and TEM. Significant grain refinement occurs by dynamic recrystallization for high temperature and low strain rate (T≥1100 ◦ C, strain rate < 0.1s−1), and at high strain rate (strain rate > 10s−1). Dynamic recrystallization is discontinuous and takes place from the grain boundaries, leading to a necklace structure. The nucleation mechanism is most likely to be bulging from grain boundaries and twin boundaries. A new insight of the modeling of dynamic recrystallization taking as a starting point the experimental data is proposed. By combining the results from the mechanical behavior study and microstructure observation, the recrystallization at steady-state is thoroughly analyzed and provides the mobility of grain boundaries. The nucleation criterion for the bulging from grain boundaries is reformulated to a more general expression suitable for any initial grain size. Nucleation frequency can be deduced from experimental data at steady-state through modeling, and is extrapolated to any deformation condition. From this point, a complete analytical model of the dynamic recrystallization is established, and provides a fair prediction on the mechanical behavior and the microstructure evolution during the hot-working process.

No presente trabalho foi avaliado o efeito da microestrutura e da capacidade de suportar carregamento de camadas nitretadas produzidas em aços ferramenta AISI H13 e AISI D2 sobre a aderência e a resistência ao desgaste microabrasivo de revestimentos de TiN-PVD. Em cada um desses aços, foram produzidas camadas nitretadas de diferentes estruturas e espessuras, e foram determinadas experimentalmente as curvas potencial início de formação de camada branca, para a nitretação a 520oC. Para o aço ferramenta AISI H13, o emprego de tempos de pré-tratamento de nitretação mais prolongados ( aproximadamente 11 h) foi necessário para aprofundar a camada nitretada e, conseqüentemente, aumentar a capacidade de suportar carregamento dos revestimentos, evitando a formação de bordas que provocam o lascamento e a escamação das camadas de TiN. Observou-se que esse tipo de falha persiste se a zona de endurecimento for pouco profunda, uma vez que a transição de propriedades mecânicas da camada de TiN para o núcleo não nitretado continua abrupta e a capacidade de suportar carregamento da camada nitretada ainda é baixa. Por outro lado, curtos tempos de nitretação (aproximadamente 42 min.) foram suficientes para aumentar a aderência das camadas de TiN ao aço ferramenta D2, pois o núcleo não nitretado desse aço possui uma capacidade de suportar carregamento razoável. Observou-se que a resistência ao desgaste microabrasivo e a aderência dos revestimentos são prejudicadas com a presença de uma camada preta na interface camada de TiN/camada nitretada. Quando a superfície dos revestimentos é carregada, falhas do tipo “casca de ovo" facilmente ocorrem. / In this work, the influence of both the microstructure and the load-bearing capacity of nitrided layers, formed on top of AISI D2 and AISI H13 tool steels, on adhesion and wear resistance of PVD-TiN coatings was studied. The threshold nitriding potential curves for the above mentioned steels and the optimum conditions of the pre-treatments which increased the adhesion as well as the wear resistance of the PVD-TiN were determined experimentally. By using longer nitriding times (about 11 h) and lower nitrogen contents in the gas mixture (about N2-5%vol.), it was possible to minimize the pile-up degree of the TiN/H13 nitrided substrates and, consequently, the occurrence of coatings chipping. This flaw persists when the nitrided layer is thin, due to an abrupt transition of mechanical properties at the TiN coating / steel core interface. Shorter nitriding times (about 42 min.) and lower nitrogen contents (about N2-5%vol.), on the other hand, are sufficient to guarantee a better adhesion of TiN coatings on AISI D2 tool steel, as the core of such steel possesses relatively better load-bearing capacity than the AISI H13 tool steel. The presence of a black layer at the TiN/nitrided layer interface was observed in all coatings deposited over nitrided layers produced above the threshold nitriding potential curves. This layer affects adversely the wear resistance and the adhesion of the TiN coatings. When higher loads are applied on the coated surface, “egg shell" type flaws easily occur.

No presente trabalho foi avaliado o efeito da microestrutura e da capacidade de suportar carregamento de camadas nitretadas produzidas em aços ferramenta AISI H13 e AISI D2 sobre a aderência e a resistência ao desgaste microabrasivo de revestimentos de TiN-PVD. Em cada um desses aços, foram produzidas camadas nitretadas de diferentes estruturas e espessuras, e foram determinadas experimentalmente as curvas potencial início de formação de camada branca, para a nitretação a 520oC. Para o aço ferramenta AISI H13, o emprego de tempos de pré-tratamento de nitretação mais prolongados ( aproximadamente 11 h) foi necessário para aprofundar a camada nitretada e, conseqüentemente, aumentar a capacidade de suportar carregamento dos revestimentos, evitando a formação de bordas que provocam o lascamento e a escamação das camadas de TiN. Observou-se que esse tipo de falha persiste se a zona de endurecimento for pouco profunda, uma vez que a transição de propriedades mecânicas da camada de TiN para o núcleo não nitretado continua abrupta e a capacidade de suportar carregamento da camada nitretada ainda é baixa. Por outro lado, curtos tempos de nitretação (aproximadamente 42 min.) foram suficientes para aumentar a aderência das camadas de TiN ao aço ferramenta D2, pois o núcleo não nitretado desse aço possui uma capacidade de suportar carregamento razoável. Observou-se que a resistência ao desgaste microabrasivo e a aderência dos revestimentos são prejudicadas com a presença de uma camada preta na interface camada de TiN/camada nitretada. Quando a superfície dos revestimentos é carregada, falhas do tipo “casca de ovo” facilmente ocorrem. / In this work, the influence of both the microstructure and the load-bearing capacity of nitrided layers, formed on top of AISI D2 and AISI H13 tool steels, on adhesion and wear resistance of PVD-TiN coatings was studied. The threshold nitriding potential curves for the above mentioned steels and the optimum conditions of the pre-treatments which increased the adhesion as well as the wear resistance of the PVD-TiN were determined experimentally. By using longer nitriding times (about 11 h) and lower nitrogen contents in the gas mixture (about N2-5%vol.), it was possible to minimize the pile-up degree of the TiN/H13 nitrided substrates and, consequently, the occurrence of coatings chipping. This flaw persists when the nitrided layer is thin, due to an abrupt transition of mechanical properties at the TiN coating / steel core interface. Shorter nitriding times (about 42 min.) and lower nitrogen contents (about N2-5%vol.), on the other hand, are sufficient to guarantee a better adhesion of TiN coatings on AISI D2 tool steel, as the core of such steel possesses relatively better load-bearing capacity than the AISI H13 tool steel. The presence of a black layer at the TiN/nitrided layer interface was observed in all coatings deposited over nitrided layers produced above the threshold nitriding potential curves. This layer affects adversely the wear resistance and the adhesion of the TiN coatings. When higher loads are applied on the coated surface, “egg shell” type flaws easily occur.

<p>Proučavane su koroziona postojanost i tendencija lepljenja različitih<br />materijala u kontaktu sa tečnom Al&ndash;Si&ndash;Cu legurom. Ispitivanjem su<br />obuhvaćeni čelik za rad na toplo, plazma nitrirani čelik i dupleks<br />slojevi sa CrN, TiAlN, TiAlSiN i CrAlN prevlakama, različitog nivoa<br />površinske hrapavosti. Za ispitivanja pomenutih fenomena<br />primenjena je metoda izvlačenja, koja je unapređena kako bi se povećale<br />njena tačnost i verodostojnost simulacije procesa livenja. Korozioni<br />efekti su pojačani tako što su uzorci osim kratkog kontakta sa odlivkom<br />zadržavani i u dužim periodima u kontaktu sa tečnom legurom (5 i 20<br />min). Uprkos opštim stavovima, za ispitivane materijale je<br />ustanovljeno da su sile izvlačenja uzoraka iz Al&ndash;Si&ndash;Cu odlivaka<br />nezavisne od njihovog hemijskog sastava. Uticaj hrapavosti je izražen<br />kod uzoraka sa prevlakama kod kojih pri smanjenju hrapavosti dolazi do<br />povećanja sile izvlačenja. Sve ispitane prevlake su sklone mehaničkom<br />lepljenju Al&ndash;Si&ndash;Cu legure za svoje površine, ali sa aspekta korozije u<br />tečnom metalu značajno prevazilaze performanse čelika i plazma<br />nitriranog sloja. Duži kontakt livene legure sa površinama prevlaka<br />uzrokovao je niže vrednosti sila izvlačenja, što je posledica<br />oksidacije površina prevlaka. Ustanovljeno je da su ispitivane<br />prevlake inertne ka tečnoj leguri aluminijuma. Međutim, dolazi do<br />oksidacije i korozije materijala podloge kroz greške rasta koje su<br />prisutne u prevlakama. Stečena znanja o identifikovanim<br />mehanizmima habanja i propadanja zaštitnih slojeva prevlaka<br />poslužiće daljem razvoju dupleks slojeva namenjenih za zaštitu alata<br />za livenje pod pritiskom.</p> / <p>Corrosion resistance and soldering tendency of different materials in molten<br />Al&ndash;Si&ndash;Cu alloy were studied. Hot-working tool steel, plasma nitrided steel and<br />duplex layers with CrN, TiAlN, TiAlSiN and CrAlN top coatings, which were<br />produced to various degree of surface roughness, were covered by the study.<br />An ejection test was employed for investigation of the concerned phenomena.<br />The ejection test was improved in order to increase its accuracy and the<br />reliability of process simulation. Samples were examined in both short and<br />extended periods of contact (5 and 20 min) with liquid casting. Casting<br />solidification was extended in order to intensify the corrosion effects. Contrary<br />to common findings, it was found that the ejection force of the investigated<br />materials does not depend on their chemical composition. For the coated<br />samples, a pronounced dependence of the ejection force on the surface<br />roughness was found. The ejection force increases with decrease in surface<br />roughness. All investigated coatings are prone to mechanical soldering by Al&ndash;<br />Si&ndash;Cu alloy. Still, their corrosion resistance substantially exceeds the corrosion<br />resistance of steel and plasma nitrided layer. Longer exposure of coated<br />samples to cast alloy induced lower ejection forces, which is a consequence<br />of coatings oxidation. It was found that the investigated coatings are inert to<br />liquid aluminium. However, the underlying material undergoes oxidation and<br />corrosion through coating growth defects. The findings concerning the wear<br />mechanisms of protective layers support further development of duplex layers<br />intended for die casting tools protection.</p>