Spelling suggestions: "subject:"hpmcas"" "subject:"pmcas""
1 |
The use of solubility parameters to predict the behaviour of a co-crystalline drug dispersed in a polymeric vehicle : approaches to the prediction of the interactions of co-crystals and their components with hypromellose acetate succinate and the characterization of that interaction using crystallographic, microscopic, thermal, and vibrational analysisIsreb, Abdullah January 2012 (has links)
Dispersing co-crystals in a polymeric carrier may improve their physicochemical properties such as dissolution rate and solubility. Additionally co-crystal stability may be enhanced. However, such dispersions have been little investigated to date. This study focuses on the feasibility of dispersing co-crystals in a polymeric carrier and theoretical calculations to predict their stability. Acetone/chloroform, ethanol/water, and acetonitrile were used to load and grow co-crystals in a HPMCAS film. Caffeine-malonic acid and ibuprofennicotinamide co-crystals were prepared using solvent evaporation method. The interactions between each of the co-crystals components and their mixtures with the polymer were studied. A solvent evaporation approach was used to incorporate each compound, a mixture, and co-crystals into HPMCAS films. Differential scanning calorimetry data revealed a higher affinity of the polymer to acidic compounds than their basic counterparts as noticed by the depression of the glass transition temperature (Tg). Moreover, the same drug loading produced films with different Tgs when different solvents were used. Solubility parameter values (SP) of the solvents were employed to predict that effect on the depression of polymer Tg with relative success. SP values were more successful in predicting the preferential affinity of two acidic compounds to interact with the polymer. This was confirmed using binary mixtures of naproxen, flurbiprofen, malonic acid, and ibuprofen. On the other hand, dispersing basic compounds such as caffeine or nicotinamide with malonic acid in HPMCAS film revealed the growth of co-crystals. A dissolution study showed that the average release of caffeine from films containing caffeine-malonic acid was not significantly different to that of films containing similar caffeine concentration. The stability of the caffeine-malonic acid co-crystals in HPMC-AS was prolonged to 8 weeks at 95% relative humidity and 45°C. The theory developed in this project, that an acidic drug with a SP value closer to the polymer will dominate the interaction process and prevent the majority of the other material from interacting with the polymer, may have utility in designing co-crystal systems in polymeric vehicles
|
2 |
The use of solubility parameters to predict the behaviour of a co-crystalline drug dispersed in a polymeric vehicle. Approaches to the prediction of the interactions of co-crystals and their components with hypromellose acetate succinate and the characterization of that interaction using crystallographic, microscopic, thermal, and vibrational analysis.Isreb, Abdullah January 2012 (has links)
Dispersing co-crystals in a polymeric carrier may improve their physicochemical
properties such as dissolution rate and solubility. Additionally co-crystal stability
may be enhanced. However, such dispersions have been little investigated to
date. This study focuses on the feasibility of dispersing co-crystals in a
polymeric carrier and theoretical calculations to predict their stability.
Acetone/chloroform, ethanol/water, and acetonitrile were used to load and grow
co-crystals in a HPMCAS film. Caffeine-malonic acid and ibuprofennicotinamide
co-crystals were prepared using solvent evaporation method. The
interactions between each of the co-crystals components and their mixtures
with the polymer were studied. A solvent evaporation approach was used to
incorporate each compound, a mixture, and co-crystals into HPMCAS films.
Differential scanning calorimetry data revealed a higher affinity of the polymer to
acidic compounds than their basic counterparts as noticed by the depression of
the glass transition temperature (Tg). Moreover, the same drug loading
produced films with different Tgs when different solvents were used. Solubility
parameter values (SP) of the solvents were employed to predict that effect on
the depression of polymer Tg with relative success. SP values were more
successful in predicting the preferential affinity of two acidic compounds to
interact with the polymer. This was confirmed using binary mixtures of
naproxen, flurbiprofen, malonic acid, and ibuprofen. On the other hand,
dispersing basic compounds such as caffeine or nicotinamide with malonic acid
in HPMCAS film revealed the growth of co-crystals. A dissolution study showed
that the average release of caffeine from films containing caffeine-malonic acid
was not significantly different to that of films containing similar caffeine concentration. The stability of the caffeine-malonic acid co-crystals in HPMC-AS was prolonged to 8 weeks at 95% relative humidity and 45°C.
The theory developed in this project, that an acidic drug with a SP value closer to the polymer will dominate the interaction process and prevent the majority of the other material from interacting with the polymer, may have utility in designing co-crystal systems in polymeric vehicles
|
3 |
Investigation of injection moulding for novel drug delivery systems. An investigation into the use of injection moulding to produce pharmaceutical dosage forms and to understand the relationship between materials, processing conditions and performance, in particular drug release and stabilityDeshmukh, Shivprasad S. January 2015 (has links)
The feasibility of the injection moulding (IM) was explored for the development of novel drug delivery systems. Controlled release formulations were developed using a substituted cellulose derivative, hydroxypropyl methyl cellulose acetate succinate (HPMCAS) and a graft co-polymer (Soluplus®). BCS class II drugs ibuprofen and the felodipine were selected based on their physicochemical properties.
In the present work, a homogenous dispersion of drugs in the polymer matrices was achieved using Hot Melt Extrusion (HME) and extruded pellets obtained were used for the development of the injection moulded systems. Four systems were developed using the IM consisting of ibuprofen-HPMCAS, ibuprofen-Soluplus®, felodipine-PEO-HPMCAS and felodipine-Soluplus®.
The ibuprofen acts as a good plasticiser compared to felodipine therefore, felodipine containing IM systems required a plasticiser (PEO) when processed with HPMCAS. The analysis of extruded pellets and injection moulded systems using modulated DSC (MDSC) and Raman spectroscopy confirmed the formation of an amorphous molecular dispersion (i.e solid solution) in the case of all four systems. The phase separation behaviour and the amorphous stability of the systems was studied at various stress conditions. This revealed the “surface crystallisation” behaviour of the ibuprofen-HPMCAS systems. Temperature-composition phase diagram constructed based on the melting point depression and the Flory-Huggins lattice solution theory provided the explanation for the phase separation and crystallisation behaviour of ibuprofen-HPMCAS systems. The advanced characterisation techniques like DMA, 2D XRD and 3D laser microscopy provided the detailed understanding of crystal habits, phase seperation and surface crystallisation. The significant effect of the stress conditions on the rate of shrinkage was observed where, higher shrinkage tendency of a HPMCAS IM system was observed compared to Soluplus® IM systems.
The extruded pellets provided the faster drug release compared to the moulded tablets suggests the effect of particle size as well as the densification during IM on the dissolution rate of the dosage form. The nature of the polymer and processing history were the contributing factors for the dissolution of the dosage forms. / The thesis is hardbound in two volumes. Volume II starts at Chapter 5, page 135.
|
4 |
Investigation of injection moulding for novel drug delivery systems : an investigation into the use of injection moulding to produce pharmaceutical dosage forms and to understand the relationship between materials, processing conditions and performance, in particular drug release and stabilityDeshmukh, Shivprasad Shahajirao January 2015 (has links)
The feasibility of the injection moulding (IM) was explored for the development of novel drug delivery systems. Controlled release formulations were developed using a substituted cellulose derivative, hydroxypropyl methyl cellulose acetate succinate (HPMCAS) and a graft co-polymer (Soluplus®). BCS class II drugs ibuprofen and the felodipine were selected based on their physicochemical properties. In the present work, a homogenous dispersion of drugs in the polymer matrices was achieved using Hot Melt Extrusion (HME) and extruded pellets obtained were used for the development of the injection moulded systems. Four systems were developed using the IM consisting of ibuprofen-HPMCAS, ibuprofen-Soluplus®, felodipine-PEO-HPMCAS and felodipine-Soluplus®. The ibuprofen acts as a good plasticiser compared to felodipine therefore, felodipine containing IM systems required a plasticiser (PEO) when processed with HPMCAS. The analysis of extruded pellets and injection moulded systems using modulated DSC (MDSC) and Raman spectroscopy confirmed the formation of an amorphous molecular dispersion (i.e solid solution) in the case of all four systems. The phase separation behaviour and the amorphous stability of the systems was studied at various stress conditions. This revealed the “surface crystallisation” behaviour of the ibuprofen-HPMCAS systems. Temperature-composition phase diagram constructed based on the melting point depression and the Flory-Huggins lattice solution theory provided the explanation for the phase separation and crystallisation behaviour of ibuprofen-HPMCAS systems. The advanced characterisation techniques like DMA, 2D XRD and 3D laser microscopy provided the detailed understanding of crystal habits, phase seperation and surface crystallisation. The significant effect of the stress conditions on the rate of shrinkage was observed where, higher shrinkage tendency of a HPMCAS IM system was observed compared to Soluplus® IM systems. The extruded pellets provided the faster drug release compared to the moulded tablets suggests the effect of particle size as well as the densification during IM on the dissolution rate of the dosage form. The nature of the polymer and processing history were the contributing factors for the dissolution of the dosage forms.
|
5 |
Suitability of cellulose ester derivatives in hot melt extrusion : thermal, rheological and thermodynamic approaches used in the characterization of cellulose ester derivatives for their suitability in pharmaceutical hot melt extrusionKarandikar, Hrushikesh M. January 2015 (has links)
Applications of Hot Melt Extrusion (HME) in pharmaceuticals have become increasingly popular over the years but nonetheless a few obstacles still remain before wide scale implementation. In many instances these improvements are related to both processing and product performance. It is observed that HME process optimisation is majorly focused on the active pharmaceutical ingredient's (API) properties. Characterising polymeric properties for their suitability in HME should be equally studied since the impact of excipients on both product and process performance is just as vital. In this work, two well-established cellulose ester derivatives: Hydroxy Propyl Methyl Cellulose Acetate Succinate (HPMCAS) and Hydroxy Propyl Methyl Cellulose Phthalate (HPMCP) are studied for their HME suitability. Their thermal, thermodynamic, rheological, thermo-chemical and degradation kinetic properties were evaluated with model plasticisers and APIs. It was found the thermal properties of HPMCP are severely compromised whereas HPMCAS is more stable in the processing zone of 150 to 200 °C. Thermodynamic properties revealed that both polymers share an important solubility parameter range (20-30 MPa P1/2P) where the majority of plasticisers and BCS class II APIs lie. Thus, greater miscibility/solubility can be expected. Further, the processability of these two polymers investigated by rheometric measurements showed HPMCAS possesses better flow properties than HPMCP because HPMCP forms a weak network of chain interactions at a molecular level. However, adding plasticisers such as PEG and TEC the flow properties of HPMCP can be tailored. The study also showed that plasticisers have a major influence on thermo-chemical and kinetic properties of polymers. For instance, PEG reduced polymer degradation with reversal in kinetic parameters whereas blends of CA produced detrimental effects and increased polymer degradation with reduction in onset degradation temperatures. Further, both polymers are observed to be chemically reactive with the APIs containing free -OH, -SOR2RN- and -NH2 groups. Finally, these properties prove that suitability of HPMCP is highly debated for HME and demands great care in use while that of HPMCAS is relatively better than HPMCP in many instances.
|
6 |
Thermal and rheological approaches for the systematic enhancement of pharmaceutical polymeric coating formulations : effects of additives on glass transition temperature, dynamic mechanical properties and coating performance in aqueous and solvent-free coating process using DSC, shear rheometry, dissolution, light profilometry and dynamic mechanical analysisIsreb, Mohammad January 2011 (has links)
Additives, incorporated in film coating formulations, and their process parameters are generally selected using a trial-and-error approach. However, coating problems and defects, especially those associated with aqueous coating systems, indicate the necessity of embracing a quality-by-design approach to identify the optimum coating parameters. In this study, the feasibility of using thermal and rheological measurements to help evaluate and design novel coating formulations has been investigated. Hydroxypropyl methylcellulose acetate succinate (HPMCAS), an enteric coating polymer, was used as the film forming polymer. Differential Scanning Calorimetry (DSC), Dynamic Mechanical Analysis (DMA), and Parallel Plate Shear Rheometery (PPSR) were used to evaluate the effect of different plasticisers on the performance of HPMCAS. The results illustrate that, for identical formulations, the DSC and DMA methods yielded up to 40% differences in glass transition temperature (Tg) values. Moreover, Tg measured using loss modulus signals were always 20-30 oC less than those measured using tan delta results in DMA testing. Absolute and relative Tg values can significantly vary depending on the geometry of the samples, clamp size, temperature ramping rate and the frequency of the oscillations. Complex viscosity data for different formulations demonstrated a variable shear thinning behaviour and a Tg independent ranking. It is, therefore, insufficient to rely purely on Tg values to determine the relative performance of additives. In addition, complex viscosity results, obtained using both the DMA and PPSR techniques at similar temperatures, are shown to be comparable. The results from both techniques were therefore used to produce continuous master curves for the HPMCAS formulations. Additionally, step strain tests showed that HPMCAS chains do not fully III disentangle after 105 seconds as predicted by the Maxwell model. Finally, in situ aqueous-based coating experiments proved that mixtures of triethyl acetyl citrate and acetylated monoglyceride (TEAC/AMG), even without cooling of the suspension, do not cause blocking of the spray nozzle whereas triethyl citrate (TEC) based formulae did. TEAC (alone or in a combination with AMG) exhibits superior wettability to HPMCAS than TEC/AMG formulations and can be used to enhance the efficiency and film quality of the dry coating process.
|
7 |
Fused deposition modeling of API-loaded mesoporous magnesium carbonateAbdelki, Andreas January 2020 (has links)
In this thesis, the incorporation of drug loaded mesoporous magnesium carbonate as an excipient for the additive manufacturing of oral tablets by fused deposition modeling was investigated. Cinnarizine, a BCS class II drug, was loaded into the pores of the mesoporous material via a soaking method, corresponding to a drug loading of 8.68 wt%. DSC measurements on the loaded material suggested that the drug was partially crystallized after incorporation, meanwhile the XRD diffractogram implied that the drug was in a state lacking long range order. The drug loaded material was combined with two pharmaceutical polymers, Aquasolve LG and Klucel ELF, and extruded into filaments with a single screw extruder. Filaments of Klucel ELF and drug loaded Upsalite (30:70 wt% ratio) were successfully implemented for the printing oral tablets, in contrast to the Aquasolve LG based filaments which were difficult to print due to thickness variations and non-uniform material distributions. The drug content obtained by TGA suggested drug loadings of 7.71 wt% and 2.23 wt% in the drug loaded Upsalite and tablets respectively. Dissolution studies using an USP II apparatus showed a slower API-release from the tablets in comparison to the crystalline drug, most probably due to slow diffusion of drug species through the polymeric matrix. For future studies, pharmaceutical polymers with higher aqueous solubility should be investigated in order to thoroughly examine the potential of utilizing the immediate release property of Upsalite.
|
8 |
Suitability of cellulose ester derivatives in hot melt extrusion.Thermal, rheological and thermodynamic approaches used in the characterization of cellulose ester derivatives for their suitability in pharmaceutical hot melt extrusionKarandikar, Hrushikesh M. January 2015 (has links)
Applications of Hot Melt Extrusion (HME) in pharmaceuticals have become increasingly popular over the years but nonetheless a few obstacles still remain before wide scale implementation. In many instances these improvements are related to both processing and product performance. It is observed that HME process optimisation is majorly focused on the active pharmaceutical ingredient's (API) properties. Characterising polymeric properties for their suitability in HME should be equally studied since the impact of excipients on both product and process performance is just as vital. In this work, two well-established cellulose ester derivatives: Hydroxy Propyl Methyl Cellulose Acetate Succinate (HPMCAS) and Hydroxy Propyl Methyl Cellulose Phthalate (HPMCP) are studied for their HME suitability. Their thermal, thermodynamic, rheological, thermo-chemical and degradation kinetic properties were evaluated with model plasticisers and APIs. It was found the thermal properties of HPMCP are severely compromised whereas HPMCAS is more stable in the processing zone of 150 to 200 °C. Thermodynamic properties revealed that both polymers share an important solubility parameter range (20-30 MPa P1/2P) where the majority of plasticisers and BCS class II APIs lie. Thus, greater miscibility/solubility can be expected. Further, the processability of these two polymers investigated by rheometric measurements showed HPMCAS possesses better flow properties than HPMCP because HPMCP forms a weak network of chain interactions at a molecular level. However, adding plasticisers such as PEG and TEC the flow properties of HPMCP can be tailored. The study also showed that plasticisers have a major influence on thermo-chemical and kinetic properties of polymers. For instance, PEG reduced polymer degradation with reversal in kinetic parameters whereas blends of CA produced detrimental effects and increased polymer degradation with reduction in onset degradation temperatures. Further, both polymers are observed to be chemically reactive with the APIs containing free -OH, -SOR2RN- and -NH2 groups. Finally, these properties prove that suitability of HPMCP is highly debated for HME and demands great care in use while that of HPMCAS is relatively better than HPMCP in many instances.
|
9 |
Thermal and rheological approaches for the systematic enhancement of pharmaceutical polymeric coating formulations. Effects of additives on glass transition temperature, dynamic mechanical properties and coating performance in aqueous and solvent-free coating process using DSC, shear rheometry, dissolution, light profilometry and dynamic mechanical analysis.Isreb, Mohammad January 2011 (has links)
Additives, incorporated in film coating formulations, and their process
parameters are generally selected using a trial-and-error approach. However,
coating problems and defects, especially those associated with aqueous
coating systems, indicate the necessity of embracing a quality-by-design
approach to identify the optimum coating parameters. In this study, the
feasibility of using thermal and rheological measurements to help evaluate and
design novel coating formulations has been investigated. Hydroxypropyl
methylcellulose acetate succinate (HPMCAS), an enteric coating polymer, was
used as the film forming polymer. Differential Scanning Calorimetry (DSC),
Dynamic Mechanical Analysis (DMA), and Parallel Plate Shear Rheometery
(PPSR) were used to evaluate the effect of different plasticisers on the
performance of HPMCAS. The results illustrate that, for identical formulations,
the DSC and DMA methods yielded up to 40% differences in glass transition
temperature (Tg) values. Moreover, Tg measured using loss modulus signals
were always 20-30 oC less than those measured using tan delta results in DMA
testing. Absolute and relative Tg values can significantly vary depending on the
geometry of the samples, clamp size, temperature ramping rate and the
frequency of the oscillations. Complex viscosity data for different formulations
demonstrated a variable shear thinning behaviour and a Tg independent
ranking. It is, therefore, insufficient to rely purely on Tg values to determine the
relative performance of additives. In addition, complex viscosity results,
obtained using both the DMA and PPSR techniques at similar temperatures, are
shown to be comparable. The results from both techniques were therefore used
to produce continuous master curves for the HPMCAS formulations.
Additionally, step strain tests showed that HPMCAS chains do not fully
III
disentangle after 105 seconds as predicted by the Maxwell model. Finally, in situ aqueous-based coating experiments proved that mixtures of triethyl acetyl citrate and acetylated monoglyceride (TEAC/AMG), even without cooling of the suspension, do not cause blocking of the spray nozzle whereas triethyl citrate (TEC) based formulae did. TEAC (alone or in a combination with AMG) exhibits superior wettability to HPMCAS than TEC/AMG formulations and can be used to enhance the efficiency and film quality of the dry coating process.
|
10 |
Systematic identification of thermal degradation products of HPMCP during hot melt extrusion processKarandikar, Hrushikesh M., Ambardekar, Rohan, Kelly, Adrian L., Gough, Tim, Paradkar, Anant R January 2015 (has links)
No / A systematic identification of the degradation products of hydroxypropyl methylcellulose phthalate (HPMCP) during hot melt extrusion (HME) has been performed. A reverse phase HPLC method was developed for the extrudates of both hydroxypropyl methylcellulose acetate succinate (HPMCAS) and HPMCP polymers to quantify their thermal hydrolytic products: acetic acid (AA), succinic acid (SA) for HPMCAS and phthalic acid (PA) for HPMCP, without hydrolysing the polymers in strong alkaline solutions. The polymers were extruded in the temperature range of 160-190 degrees C at different screw rotation speeds and hydrolytic impurities were analysed. Investigation of extruded HPMCP showed an additional thermal degradation product, who is structural elucidation revealed to be phthalic anhydride (PAH). Moreover, two environmental analytical impurities, dimethyl phthalate and methyl benzoate formed in situ were recorded on GC-MS and their origin was found to be associated with PAH derivatization. Using the experimental data gathered during this study, a degradation mechanism for HPMCP is proposed.
|
Page generated in 0.0273 seconds