Nowadays, Multi-GHz analog-to-digital converters (ADCs) are becoming more and more popular in radar systems, software-de ned radio (SDR) and wideband communications, because they can realize much higher operation speed through using many interleaved sub-ADCs to relax ADC sampling rates. Although the time interleaved ADC has some issues such as gain mismatch, o set mismatch and timing skew between each ADC channel, these deterministic errors can be solved by previous works such as digital calibration technique. However, time-interleaved ADCs require a precise sample clock to achieve an acceptable e ective-numberof- bits (ENOB) which can be degraded by jitter in the sample clock. The clock generation circuits presented in this work achieves sub-picosecond jitter performance in 180nm CMOS which is suitable for time-interleaved ADC. Two di erent test chips were fabricated in 180nm CMOS to investigate the low jitter design technique. The low jitter delay line in two chips were designed in two di erent ways, but both of them utilized the low jitter design technique. In rst test chip, the measured RMS jitter is 0.1061ps for each delay stage. The second chip uses the proposed low jitter Delay-Locked Loop can work from 80MHz to 120MHz, which means it can provide the time interleaved ADC with 2.4GHz to 3.6GHz low jitter sample clock, the measured delay stage jitter performance in second test chip is 0.1085ps.

Time-Interleaved Analog to Digital Converters (TI ADC) consist of several individual sub-converters operating at a lower sampling rate, working in parallel, and in a circular loop. Thereby, they are increasing the sampling rate without compromising on the resolution during conversion, at high sampling rates. The latter is the main requirement in the area of radio frequency sampling. However, they suffer from mismatches caused by the different characteristics in each sub-converter and the TI structure. The output of the TI ADC under consideration contains a lot of harmonics and spurious tones due to the non-linearities mismatch between the sub-converters. Therefore, previously extensive frequency planning was performed to avoid the input signal from coinciding with these harmonic bins. More importance has been given to digital calibration in recent years where algorithms are developed and implemented outside ADC in a Digital signal processor (DSP), whereas the compensation is done in real time. In this work, we model the distortions and the harmonics present in the TI ADC output to get a clear understanding of the TI ADC. A post-correction block is developed for the cancellation of the characterized harmonics. The suggested method is tested on the TI ADCs working at radio frequencies, but is valid also for other types of ADCs, such as pipeline ADCs and sigma-delta ADCs.

Les convertisseurs analogique-numérique à entrelacement temporel (TIADC) semblent être une solution prometteuse dans le monde de la conversion analogique-numérique. Leur fréquence d’échantillonnage peut théoriquement être augmentée en augmentant le nombre de convertisseurs en parallèle. En réalité, des désappariements entre les convertisseurs peuvent fortement dégrader les performances, particulièrement à haute fréquence d’échantillonnage ou à haute résolution. Ces défauts d’appariement peuvent être réduits en utilisant des techniques de calibration en arrière-plan. La première partie de cette thèse est consacrée à l’étude des sources et effets des différents types de désappariements dans un TIADC. Des indicateurs de performance tels que le SNDR ou la SFDR sont exprimés en fonction du niveau des désappariements. Dans la deuxième partie, des nouvelles techniques de calibration sont proposées. Ces techniques permettent de réduire les effets des désappariements d’offset, de gain, d’instant d’échantillonnage et de bande passante. Les désappariements sont estimés en se basant sur des propriétés statistiques du signal et la reconstruction des échantillons de sortie se fait en utilisant des filtres numériques. La troisième partie démontre les performance d’un TIADC fonctionnant a une fréquence d’échantillonnage de 1.6 GE/s et comprenant les calibration d’offset, de gain et d’instant d’échantillonnage proposées. Les raies fréquentielles dues aux désappariements sont réduites à un niveau de -70dBc jusqu’à une fréquence d’entrée de 750 MHz. Ce circuit démontre une meilleure correction de désappariements que des circuits similaires récemment publiés, et ce avec une augmentation de puissance consommée et de surface relativement faible. / Time-interleaved analog-to-digital converters (TIADC) seem to be the holy grail of analog-to-digital conversion. Theoretically, their sampling speed can be increased, very simply, by duplicating the sub-converters. The real world is different because mismatches between the converters strongly reduce the TIADC performance, especially when trying to push forward the sampling speed, or the resolution of the converter. Using background digital mismatch calibration can alleviate this limitation. The first part of the thesis is dedicated to studying the sources and effects of mismatches in a TIADC. Performance metrics such as the SNDR and the SFDR are derived as a function of the mismatch levels. In the second part, new background digital mismatch calibration techniques are presented. They are able to reduce the offset, gain, skew and bandwidth mismatch errors. The mismatches are estimated by using the statistical properties of the input signal and digital filters are used to reconstruct the correct output samples. In the third part, a 1.6 GS/s TIADC circuit, implementing offset, gain and skew mismatch calibration, demonstrates a reduction of the mismatch spurs down to a level of -70 dBFS, up to an input frequency of 750 MHz. The circuit achieves the lowest level of mismatches among TIADCs in the same frequency range, with a reasonable power and area, in spite of the overhead caused by the calibration.

"This work describes the integrated circuit design of a 16-bit, 10Msample/sec, combination ‘split’ interleaved analog to digital converter. Time interleaving of analog to digital converters has been used successfully for many years as a technique to achieve faster speeds using multiple identical converters. However, efforts to achieve higher resolutions with this technique have been difficult due to the precise matching required of the converter channels. The most troublesome errors in these types of converters are gain, offset and timing differences between channels. The ‘split ADC’ is a new concept that allows the use of a deterministic, digital, self calibrating algorithm. In this approach, an ADC is split into two paths, producing two output codes from the same input sample. The difference of these two codes is used as the calibration signal for an LMS error estimation algorithm that drives the difference error to zero. The ADC is calibrated when the codes are equal and the output is taken as the average of the two codes. The ‘split’ ADC concept and interleaved architecture are combined in this IC design to form the core of a high speed, high resolution, and self-calibrating ADC system. The dual outputs are used to drive a digital calibration engine to correct for the channel mismatch errors. This system has the speed benefits of interleaving while maintaining high resolution. The hardware for the algorithm as well as the ADC can be implemented in a standard 0.25um CMOS process, resulting in a relatively inexpensive solution. This work is supported by grants from Analog Devices Incorporated (ADI) and the National Science Foundation (NSF). "

Les convertisseurs analogique-numérique à entrelacement temporel (TIADC) semblent être une solution prometteuse dans le monde de la conversion analogique-numérique. Leur fréquence d’échantillonnage peut théoriquement être augmentée en augmentant le nombre de convertisseurs en parallèle. En réalité, des désappariements entre les convertisseurs peuvent fortement dégrader les performances, particulièrement à haute fréquence d’échantillonnage ou à haute résolution. Ces défauts d’appariement peuvent être réduits en utilisant des techniques de calibration en arrière-plan. La première partie de cette thèse est consacrée à l’étude des sources et effets des différents types de désappariements dans un TIADC. Des indicateurs de performance tels que le SNDR ou la SFDR sont exprimés en fonction du niveau des désappariements. Dans la deuxième partie, des nouvelles techniques de calibration sont proposées. Ces techniques permettent de réduire les effets des désappariements d’offset, de gain, d’instant d’échantillonnage et de bande passante. Les désappariements sont estimés en se basant sur des propriétés statistiques du signal et la reconstruction des échantillons de sortie se fait en utilisant des filtres numériques. La troisième partie démontre les performance d’un TIADC fonctionnant a une fréquence d’échantillonnage de 1.6 GE/s et comprenant les calibration d’offset, de gain et d’instant d’échantillonnage proposées. Les raies fréquentielles dues aux désappariements sont réduites à un niveau de -70dBc jusqu’à une fréquence d’entrée de 750 MHz. Ce circuit démontre une meilleure correction de désappariements que des circuits similaires récemment publiés, et ce avec une augmentation de puissance consommée et de surface relativement faible. / Time-interleaved analog-to-digital converters (TIADC) seem to be the holy grail of analog-to-digital conversion. Theoretically, their sampling speed can be increased, very simply, by duplicating the sub-converters. The real world is different because mismatches between the converters strongly reduce the TIADC performance, especially when trying to push forward the sampling speed, or the resolution of the converter. Using background digital mismatch calibration can alleviate this limitation. The first part of the thesis is dedicated to studying the sources and effects of mismatches in a TIADC. Performance metrics such as the SNDR and the SFDR are derived as a function of the mismatch levels. In the second part, new background digital mismatch calibration techniques are presented. They are able to reduce the offset, gain, skew and bandwidth mismatch errors. The mismatches are estimated by using the statistical properties of the input signal and digital filters are used to reconstruct the correct output samples. In the third part, a 1.6 GS/s TIADC circuit, implementing offset, gain and skew mismatch calibration, demonstrates a reduction of the mismatch spurs down to a level of -70 dBFS, up to an input frequency of 750 MHz. The circuit achieves the lowest level of mismatches among TIADCs in the same frequency range, with a reasonable power and area, in spite of the overhead caused by the calibration.

<p>Nonuniform sampling occurs in many practical applications either intentionally or unintentionally. This thesis deals with the reconstruction of two-periodic nonuniform signals which is of great importance in two-channel time-interleaved analog-to-digital converters. In a two-channel time-interleaved ADC, aperture delay mismatch between the channels gives rise to a two-periodic nonuniform sampling pattern, resulting in distortion and severely affecting the linearity of the converter. The problem is solved by digitally recovering a uniformly sampled sequence from a two-periodic nonuniformly sampled set. For this purpose, a time-varying FIR filter is employed. If the sampling pattern is known and fixed, this filter can be designed in an optimal way using least-squares or minimax design. When the sampling pattern changes now and then as during the normal operation of time-interleaved ADC, these filters have to be redesigned. This has implications on the implementation cost as general on-line design is cumbersome. To overcome this problem, a novel time-varying FIR filter with polynomial impulse response is developed and characterized in this thesis. The main advantage with these filters is that on-line design is no longer needed. It now suffices to perform only one design before implementation and in the implementation it is enough to adjust only one variable parameter when the sampling pattern changes. Thus the high implementation cost is decreased substantially.</p><p>Filter design and the associated performance metrics have been validated using MATLAB. The design space has been explored to limits imposed by machine precision on matrix inversions. Studies related to finite wordlength effects in practical filter realisations have also been carried out. These formulations can also be extended to the general M - periodic nonuniform sampling case.</p>

Nonuniform sampling occurs in many practical applications either intentionally or unintentionally. This thesis deals with the reconstruction of two-periodic nonuniform signals which is of great importance in two-channel time-interleaved analog-to-digital converters. In a two-channel time-interleaved ADC, aperture delay mismatch between the channels gives rise to a two-periodic nonuniform sampling pattern, resulting in distortion and severely affecting the linearity of the converter. The problem is solved by digitally recovering a uniformly sampled sequence from a two-periodic nonuniformly sampled set. For this purpose, a time-varying FIR filter is employed. If the sampling pattern is known and fixed, this filter can be designed in an optimal way using least-squares or minimax design. When the sampling pattern changes now and then as during the normal operation of time-interleaved ADC, these filters have to be redesigned. This has implications on the implementation cost as general on-line design is cumbersome. To overcome this problem, a novel time-varying FIR filter with polynomial impulse response is developed and characterized in this thesis. The main advantage with these filters is that on-line design is no longer needed. It now suffices to perform only one design before implementation and in the implementation it is enough to adjust only one variable parameter when the sampling pattern changes. Thus the high implementation cost is decreased substantially. Filter design and the associated performance metrics have been validated using MATLAB. The design space has been explored to limits imposed by machine precision on matrix inversions. Studies related to finite wordlength effects in practical filter realisations have also been carried out. These formulations can also be extended to the general M - periodic nonuniform sampling case.