abstract: Polymer matrix composites (PMCs) are attractive structural materials due to their high stiffness to low weight ratio. However, unidirectional PMCs have low shear strength and failure can occur along kink bands that develop on compression due to plastic microbuckling that carry strains large enough to induce nonlinear matrix deformation. Reviewing the literature, a large fraction of the existing work is for uniaxial compression, and the effects of stress gradients, such as those present during bending, have not been as well explored, and these effects are bound to make difference in terms of kink band nucleation and growth. Furthermore, reports on experimental measurements of strain fields leading to and developing inside these bands in the presence of stress gradients are also scarce and need to be addressed to gain a full understanding of their behavior when UDCs are used under bending and other spatially complex stress states. In a light to bridge the aforementioned gaps, the primary focus of this work is to understand mechanisms for kink band evolution under an influence of stress-gradients induced during bending. Digital image correlation (DIC) is used to measure strains inside and around the kink bands during 3-point bending of samples with 0°/90° stacking made of Ultra-High Molecular Weight Polyethylene Fibers. Measurements indicate bands nucleate at the compression side and propagate into the sample carrying a mixture of large shear and normal strains (~33%), while also decreasing its bending stiffness. Failure was produced by a combination of plastic microbuckling and axial splitting. The microstructure of the kink bands was studied and used in a microstructurally explicit finite element model (FEM) to analyze stresses and strains at ply level in the samples during kink band evolution, using cohesive zone elements to represent the interfaces between plies. Cohesive element properties were deduced by a combination of delamination, fracture and three-point bending tests used to calibrate the FEMs. Modeling results show that the band morphology is sensitive to the shear and opening properties of the interfaces between the plies. / Dissertation/Thesis / Doctoral Dissertation Mechanical Engineering 2016

L'objectif de cette thèse est l'étude de la déformation, à l'échelle microscopique, de la phase MAX Ti2AlN, synthétisée par métallurgie des poudres. Ce travail se divise en trois parties : une première dans laquelle l'accent a été mis sur l'hystérèse mécanique des phases MAX via des essais cyclés, en nanoindentation sphérique et compression ex-situ de micro-piliers, sur des grains d'orientations différentes déterminées par l'EBSD. Dans la deuxième nous nous sommes intéressés à la déformation de micropiliers via des essais de compression cyclés in-situ couplés à la micro-diffraction Laue. L'objectif a été d'analyser les taches diffraction au cours de la déformation du pilier afin de mettre en évidence les mécanismes de déformation élémentaires mis en jeu et d'observer les structures finales via des images MEB post-mortem des piliers. Enfin, une dernière dans laquelle l'objectif a été l'étude des mécanismes de déformation en température à l'échelle microscopique via des essais de nano-indentation allant jusqu'à 800°C. La caractérisation des lignes de glissement en surface et des configurations microstructurales sous l'empreinte a été réalisée par AFM et MET respectivement. Toutes les données recueillies par ces divers essais aux petites échelles, ont permis d'affiner notre compréhension des mécanismes de déformation du monocristal de phase MAX, notamment vis à vis des modèles usuellement proposés dans la littérature. / The thesis's goal is to study the deformation, at microscopic scale, of the MAX phase Ti2AlN synthesized by powder metallurgy. This work is divided into three parts: in the first part, the interest has been put on the hysteretic behavior of the MAX phases via cyclic mechanical solicitations, during spherical indentation tests and ex-situ compression of micro-pillars, on differently orientated grains beforehand determined by EBSD. In the second part, we were interested into the micro-pillar's deformation via insitu cyclic compression tests coupled with Laue micro-diffraction. The goal was to analyse the evolution diffraction lines during the pillar's deformation in order to highlight the elementary deformation mechanisms and to observe the finale structures via the post-mortem SEM imaging of the pillars. Finally, a last part was devoted to study the deformation mechanisms in temperature at microscopic scale via nano-indentation tests up to 800°C. The characterization of the slip lines on the surface has been revealed by AFM and that of t he microstructural configurations (dislocations) under the indent has been done by TEM. All data collected by these various tests at the small scales have refined our understanding of the deformation mechanisms of crystal MAX phase, particularly with respect to the models usually proposed in the literature.